Results for “parametric study” — Page 33

NASA NTRS2011

Higher Order Parametric Excitation Modes for Spaceborne Quadrupole Mass Spectrometers

This paper describes a technique to significantly improve upon the mass peak shape and mass resolution of spaceborne quadrupole mass spectrometers (QMSs) through higher order auxiliary excitation of the quadrupole field. Using a novel multiresonant tank circuit, additional frequency components can be used to drive modulating voltages on the quadrupole rods in a practical manner, suitable for both improved commercial applications and spaceflight instruments. Auxiliary excitation at frequencies near twice that of the fundamental quadrupole RF frequency provides the advantages of previously studied parametric excitation techniques, but with the added benefit of increased sensed excitation amplitude dynamic range and the ability to operate voltage scan lines through the center of upper stability islands. Using a field programmable gate array, the amplitudes and frequencies of all QMS signals are digitally generated and managed, providing a robust and stable voltage control system. These techniques are experimentally verified through an interface with a commercial Pfeiffer QMG422 quadrupole rod system.When operating through the center of a stability island formed from higher order auxiliary excitation, approximately 50% and 400% improvements in 1% mass resolution and peak stability were measured, respectively, when compared with traditional QMS operation. Although tested with a circular rod system, the presented techniques have the potential to improve the performance of both circular and hyperbolic rod geometry QMS sensors.

Gershman, D. J.↗

NASA NTRS2013

Development of a SMA-Based Slat-Cove Filler for Reduction of Aeroacoustic Noise Associated With Transport-Class Aircraft Wings

Airframe noise is a significant part of the overall noise produced by typical, transport-class aircraft during the approach and landing phases of flight. Leading-edge slat noise is a prominent source of airframe noise. The concept of a slat-cove filler was proposed in previous work as an effective means of mitigating slat noise. Bench-top models were deployed at 75% scale to study the feasibility of producing a functioning slat-cove filler. Initial results from several concepts led to a more-focused effort investigating a deformable structure based upon pseudoelastic SMA materials. The structure stows in the cavity between the slat and main wing during cruise and deploys simultaneously with the slat to guide the aerodynamic flow suitably for low noise. A qualitative parametric study of SMA-enabled, slat-cove filler designs was performed on the bench-top. Computational models were developed and analyses were performed to assess the displacement response under representative aerodynamic load. The bench-top and computational results provide significant insight into design trades and an optimal design.

Turner, Travis L.↗

NASA NTRS1993

ISPAN (Interactive Stiffened Panel Analysis): A tool for quick concept evaluation and design trade studies

Interactive Stiffened Panel Analysis (ISPAN) modules, written in FORTRAN, were developed to provide an easy to use tool for creating finite element models of composite material stiffened panels. The modules allow the user to interactively construct, solve and post-process finite element models of four general types of structural panel configurations using only the panel dimensions and properties as input data. Linear, buckling and post-buckling solution capability is provided. This interactive input allows rapid model generation and solution by non finite element users. The results of a parametric study of a blade stiffened panel are presented to demonstrate the usefulness of the ISPAN modules. Also, a non-linear analysis of a test panel was conducted and the results compared to measured data and previous correlation analysis.

Hairr, John W.↗

NASA NTRS1980

Analytical study of the effects of wind tunnel turbulence on turbofan rotor noise

An analytical study of the effects of wind tunnel turbulence on turbofan rotor noise was carried out to evaluate the effectiveness of the NASA Ames 40 by 80-foot wind tunnel in simulating flight levels of fan noise. A previously developed theory for predicting rotor/turbulence interaction noise, refined and extended to include first-order effects of inlet turbulence anisotropy, was employed to carry out a parametric study of the effects of fan size, blade number, and operating line for outdoor test stand, NASA Ames wind tunnel, and flight inlet turbulence conditions. A major result of this study is that although wind tunnel rotor/turbulence noise levels are not as low as flight levels, they are substantially lower than the outdoor test stand levels and do not mask other sources of fan noise.

Gliebe, P. R.↗

NASA NTRS1983

Analysis of Nonplanar Wing-tip-mounted Lifting Surfaces on Low-speed Airplanes

Nonplanar wing tip mounted lifting surfaces reduce lift induced drag substantially. Winglets, which are small, nearly vertical, winglike surfaces, are an example of these devices. To achieve reduction in lift induced drag, winglets produce significant side forces. Consequently, these surfaces can seriously affect airplane lateral directional aerodynamic characteristics. Therefore, the effects of nonplanar wing tip mounted surfaces on the lateral directional stability and control of low speed general aviation airplanes were studied. The study consists of a theoretical and an experimental, in flight investigation. The experimental investigation involves flight tests of winglets on an agricultural airplane. Results of these tests demonstrate the significant influence of winglets on airplane lateral directional aerodynamic characteristics. It is shown that good correlations exist between experimental data and theoretically predicted results. In addition, a lifting surface method was used to perform a parametric study of the effects of various winglet parameters on lateral directional stability derivatives of general aviation type wings.

Vandam, C. P.↗

NASA NTRS1989

A case study of wave-current interaction near an oceanic front

High resolution directional wave spectrum data were obtained from two NASA airborne radars during the Frontal Air-Sea Interaction Experiment in February 1986. The observations show a significant change in the wave number spectrum across the front. On the basis of surveys from a towed sensor and on satellite imagery, the front location and current field are estimated. A numerical model is developed for the wave-current interaction and is used to model the wave refraction across the frontal current. A parametric study is performed to demonstrate the effects of current meandering. The main consequence of meandering is the formation of caustics and shadow zone regions in which the wave energy is significantly enhanced or reduced. Spectral simulation along the aircraft track reveals a reduction of more that 60 percent in wave energy in the shadow zone; this is consistent with the observations.

Liu, A. K.↗

NASA NTRS1999

Buckling Behavior of Compression-Loaded Quasi-Isotropic Curved Panels with a Circular Cutout

Results from a numerical and experimental study of the response of compression-loaded quasi-isotropic curved panels with a centrally located circular cutout are presented. The numerical results were obtained by using a geometrically nonlinear finite element analysis code. The effects of cutout size, panel curvature and initial geo- metric imperfections on the overall response of compression-loaded panels are described. In addition, results are presented from a numerical parametric study that indicate the effects of elastic circumferential edge restraints on the prebuckling and buckling response of a selected panel and these numerical results are compared to experimentally measured results. These restraints are used to identify the effects of circumferential edge restraints that are introduced by the test fixture that was used in the present study. It is shown that circumferential edge restraints can introduce substantial nonlinear prebuckling deformations into shallow compression-loaded curved panels that can results in a significant increase in buckling load.

Hilburger, Mark W.↗

NASA NTRS2023

Strategic Deconfliction of Small Unmanned Aircraft Using Operational Volume Blocks at Crossing Waypoints

In this research, first, analytical case studies are performed to understand the parameters on which the minimum temporal separation between unmanned aircraft at crossing waypoints is dependent for enabling strategic deconfliction. The analytical expressions show that the minimum temporal separation is a function of the length and width of operational volume blocks, the relative positions of the active operational volume blocks, groundspeed of unmanned aircraft, and the incoming crossing angle. Next, the parametric study shows that the impact of the incoming crossing angle on the minimum temporal separation at a crossing waypoint increases with an increase in the width of the operational volume blocks. Finally, simulation studies are performed to understand the impact of operational volume block sizing, on-demand departure rate, minimum departure time separation, and the incoming crossing angle on the average ground delay of unmanned aircraft traveling on two routes with a single crossing waypoint and identical on-demand departure rate. Each unmanned aircraft’s estimated time of arrival at a crossing waypoint is adjusted by introducing a ground delay in departure time; no other controls (e.g., speed adjustments) are applied for strategic deconfliction. Simulation studies show that the impact of the minimum temporal separation at a crossing waypoint on the average ground delay of flights is negligible if the minimum departure time separation is at least two times the minimum temporal separation. Therefore, with an increase in minimum departure time separation at a depot, the impact of increased length of operational volume blocks enclosing the crossing waypoint on the ground delay is offset to an extent.

Operational intent↗

NASA NTRS2023

Strategic Deconfliction of Small Unmanned Aircraft Using Operational Volume Blocks at Crossing Waypoints

In this research, first, analytical case studies are performed to understand the parameters on which the minimum temporal separation between unmanned aircraft at crossing waypoints is dependent for enabling strategic deconfliction. The analytical expressions show that the minimum temporal separation is a function of the length and width of operational volume blocks, the relative positions of the active operational volume blocks, groundspeed of unmanned aircraft, and the incoming crossing angle. Next, the parametric study shows that the impact of the incoming crossing angle on the minimum temporal separation at a crossing waypoint increases with an increase in the width of the operational volume blocks. Finally, simulation studies are performed to understand the impact of operational volume block sizing, on-demand departure rate, minimum departure time separation, and the incoming crossing angle on the average ground delay of unmanned aircraft traveling on two routes with a single crossing waypoint and identical on-demand departure rate. Each unmanned aircraft’s estimated time of arrival at a crossing waypoint is adjusted by introducing a ground delay in departure time; no other controls (e.g., speed adjustments) are applied for strategic deconfliction. Simulation studies show that the impact of the minimum temporal separation at a crossing waypoint on the average ground delay of flights is negligible if the minimum departure time separation is at least two times the minimum temporal separation. Therefore, with an increase in minimum departure time separation at a depot, the impact of increased length of operational volume blocks enclosing the crossing waypoint on the ground delay is offset to an extent.

Operational Intent↗

NASA NTRS1988

An analytical study of the effects of transverse shear deformation and anisotropy on natural vibration frequencies of laminated cylinders

Natural vibration frequencies of orthotropic and anisotropic simply supported right circular cylinders are predicted using a higher-order transverse-shear deformation theory. A comparison of natural vibration frequencies predicted by first-order transverse-shear deformation theory and the higher-order theory shows that an additional allowance for transverse shear deformation has a negligible effect on the lowest predicted natural vibration frequencies of laminated cylinders but significantly reduces the higher natural vibration frequencies. A parametric study of the effects of ply orientation on the natural vibration frequencies of laminated cylinders indicates that while stacking sequence affects natural vibration frequencies, cylinder geometry is more important in predicting transverse-shear deformation effects. Interaction curves for cylinders subjected to axial compressive loadings and low natural vibration frequencies indicate that transverse shearing effects are less important in predicting low natural vibration frequencies than in predicting axial compressive buckling loads. The effects of anisotropy are more important than the effects of transverse shear deformation for most strongly anisotropic laminated cylinders in predicting natural vibration frequencies. However, transverse-shear deformation effects are important in predicting high natural vibration frequencies of thick-walled laminated cylinders. Neglecting either anisotropic effects or transverse-shear deformation effects leads to non-conservative errors in predicted natural vibration frequencies.

Jegley, Dawn C.↗

NASA NTRS1989

An analytical study of the effects of transverse shear deformation and anisotropy on natural vibation frequencies of laminated cylinders

Natural vibration frequencies of orthotropic and anisotropic simply supported right circular cylinders are predicted using a higher-order transverse-shear deformation theory. A comparison of natural vibration frequencies predicted by first-order transverse-shear deformation theory and the higher-order theory shows that an additional allowance for transverse shear deformation has a negligible effect on the lowest predicted natural vibration frequencies of laminated cylinders but significantly reduces the higher natural vibration frequencies. A parametric study of the effects of ply orientation on the natural vibration frequencies of laminated cylinders indicates that while stacking sequence affects natural vibration frequencies, cylinder geometry is more important in predicting transverse-shear deformation effects. Interaction curves for cylinders subjected to axial compressive loadings and low natural vibration frequencies indicate that transverse shearing effects are less important in predicting low natural vibration frequencies than in predicting axial compressive buckling loads. The effects of anisotropy are more important than the effects of transverse shear deformation for most strongly anisotropic laminated cylinders in predicting natural vibration frequencies. However, transverse-shear deformation effects are important in predicting high natural vibration frequencies of thick-walled laminated cylinders. Neglecting either anisotropic effects or transverse-shear deformation effects leads to non-conservative errors in predicted natural vibration frequencies.

Jegley, Dawn C.↗

NASA NTRS1993

Response of laminated composite plates to low-speed impact by airgun-propelled and dropped-weight impactors

An analytical procedure has been developed to determine the transient response of simply supported, rectangular laminated composite plates subjected to impact loads from airgun-propelled or dropped-weight impactors. A first-order shear-deformation theory has been included in the analysis to represent properly any local short-wavelength transient bending response. The impact force has been modeled as a locally distributed load with a cosine-cosine distribution. A double Fourier series expansion and the Timoshenko small increment method have been used to determine the contact force, out-of-plane deflections, and inplane strains and stresses at any plate location due to an impact force at any plate location. The results of experimental and analytical studies are compared for quasi-isotropic laminates. The results indicate the importance of including transverse shear deformation effects in the analysis for predicting the response of laminated plates subjected to both airgun-propelled and dropped-weight impactors. The results also indicate that plate boundary conditions influence the axial strains more significantly than the contact force for a dropped-weight impactor. The results of parametric studies identify a scaling approach based on impactor momentum that suggests an explanation for the differences in the responses of plates impacted by airgun-propelled or dropped-weight impactors.

Prasad, Chunchu B.↗

NASA NTRS1994

Response of laminated composite plates to low-speed impact by different impactors

An analytic procedure has been developed to determine the transient response of simply supported, retangular laminated composite plates subjected to impact loads from airgun-propelled or drop-weight impactors. A first-order shear deformation theory has been included in the analysis to represent properly any local short-wavelength transient bending response. The impact force has been modeled as a locally distributed load with cosine-cosine distribution. A double Fourier series expansion and the Timoshenko small increment method have been used to determine the contact force, out-of-plane deflections, and in-plane strains and stresses at any plate location due to an impact force at any plate location. The results of experimental and analytical studies are compared for quasi-isotropic laminates. The results indicate the importance of including transverse shear deformation effects in the analysis for predicting the response of laminated plates subjected to both airgun-propelled and dropped-weight impactors. The results also indicate that plate boundary conditions influence the axial strains more significantly than the contact force for a dropped-weight impactor. The results of parametric studies identify a scaling approach based on impactor momentum that may account for the differences in the responses of plates impacted by airgun-propelled or dropped-weight impactors.

Prasad, Chunchu↗

NASA NTRS2003

Aerodynamic Design Study of an Advanced Active Twist Rotor

An Advanced Active Twist Rotor (AATR) is currently being developed by the U.S. Army Vehicle Technology Directorate at NASA Langley Research Center. As a part of this effort, an analytical study was conducted to determine the impact of blade geometry on active-twist performance and, based on those findings, propose a candidate aerodynamic design for the AATR. The process began by creating a baseline design which combined the dynamic design of the original Active Twist Rotor and the aerodynamic design of a high lift rotor concept. The baseline model was used to conduct a series of parametric studies to examine the effect of linear blade twist and blade tip sweep, droop, and taper on active-twist performance. Rotor power requirements and hub vibration were also examined at flight conditions ranging from hover to advance ratio = 0.40. A total of 108 candidate designs were analyzed using the second-generation version of the Comprehensive Analytical Model of Rotorcraft Aerodynamics and Dynamics (CAMRAD II) code. The study concluded that the vibration reduction capabilities of a rotor utilizing controlled, strain-induced twisting are enhanced through the incorporation of blade tip sweep, droop, and taper into the blade design, while they are degraded by increasing the nose-down linear blade twist. Based on the analysis of rotor power, hub vibration, and active-twist response, a candidate aerodynamic design for the AATR consisting of a blade with approximately 10 degrees of linear blade twist and a blade tip design with 30 degree sweep, 10 degree droop, and 2.5:1 taper ratio over the outer five percent of the blade is proposed.

Sekula, Martin K.↗

NASA NTRS1989

A combined Eulerian-Lagrangian two-phase flow analysis of SSME HPOTP nozzle plug trajectories. I - Methodology

A computer code has been developed for the analysis of SSME (Space Shuttle Main Engine) HPOTP (High Pressure Oxidizer Turbo Pump) nozzle plug trajectories in the turnaround duct downstream of the turbine. The algorithm is based on a combined Eulerian-Lagrangian analysis originally developed for the study of two-phase flows. The Lagrangian part of this analysis has been enhanced to include three-dimensional particle motion and the effect of particle-wall collisions in complex geometries (with a large number of boundaries). The sensitivity of the nozzle plug trajectories to a variety of parameters has been determined, via the qualitative analysis of a select number of computed trajectories. The results of extensive parametric studies have been reported in a companion paper.

De Jong, Frederik J.↗

NASA NTRS1990

Recent experience with multidisciplinary analysis and optimization in advanced aircraft design

The task of modern aircraft design has always been complicated due to the number of intertwined technical factors from the various engineering disciplines. Furthermore, this complexity has been rapidly increasing by the development of such technologies as aeroelasticity tailored materials and structures, active control systems, integrated propulsion/airframe controls, thrust vectoring, and so on. Successful designs that achieve maximum advantage from these new technologies require a thorough understanding of the physical phenomena and the interactions among these phenomena. A study commissioned by the Aeronautical Sciences and Evaluation Board of the National Research Council has gone so far as to identify technology integration as a new discipline from which many future aeronautical advancements will arise. Regardless of whether one considers integration as a new discipline or not, it is clear to all engineers involved in aircraft design and analysis that better methods are required. In the past, designers conducted parametric studies in which a relatively small number of principal characteristics were varied to determine the effect on design requirements which were themselves often diverse and contradictory. Once a design was chosen, it then passed through the various engineers' disciplines whose principal task was to make the chosen design workable. Working in a limited design space, the discipline expert sometimes improved the concept, but more often than not, the result was in the form of a penalty to make the original concept workable. If an insurmountable problem was encountered, the process began over. Most design systems that attempt to account for disciplinary interactions have large empirical elements and reliance on past experience is a poor guide in obtaining maximum utilizations of new technologies. Further compounding the difficulty of design is that as the aeronautical sciences have matured, the discipline specialist's area of research has generally narrowed as more sophisticated methods are developed in the specialist's area of expertise. The results have been a decrease in the awareness of the impact of his decisions on other disciplines. This paper will outline the progress and problems encountered in the analysis, design, optimization sensitivity analysis, mathematical modeling, and configurations control and the means by which they are being solved. The breadth versus depth dilemma in analysis and design and the means for coping with that dilemma will be discussed. Finally, the all-important human aspects and the need for a new 'culture ' for doing business in an integrated, multidisciplinary design environment are discussed.

Dollyhigh, Samuel M.↗

NASA NTRS1975

Microwave power transmission system studies. Volume 4: Sections 9 through 14 with appendices

The microwave rectifier technology, approaches to the receiving antenna, topology of rectenna circuits, assembly and construction, ROM cost estimates are discussed. Analyses and cost estimates for the equipment required to transmit the ground power to an external user. Noise and harmonic considerations are presented for both the amplitron and klystron and interference limits are identified and evaluated. The risk assessment discussion is discussed wherein technology risks are rated and ranked with regard to their importance in impacting the microwave power transmission system. The system analyses and evaluation are included of parametric studies of system relationships pertaining to geometry, materials, specific cost, specific weight, efficiency, converter packing, frequency selection, power distribution, power density, power output magnitude, power source, transportation and assembly. Capital costs per kW and energy costs as a function of rate of return, power source and transportation costs as well as build cycle time are presented. The critical technology and ground test program are discussed along with ROM costs and schedule. The orbital test program with associated critical technology and ground based program based on full implementation of the defined objectives is discussed.

Maynard, O. E.↗

NASA NTRS2000

Solar Power System Options for the Radiation and Technology Demonstration Spacecraft

The Radiation and Technology Demonstration (RTD) Mission has the primary objective of demonstrating high-power (10 kilowatts) electric thruster technologies in Earth orbit. This paper discusses the conceptual design of the RTD spacecraft photovoltaic (PV) power system and mission performance analyses. These power system studies assessed multiple options for PV arrays, battery technologies and bus voltage levels. To quantify performance attributes of these power system options, a dedicated Fortran code was developed to predict power system performance and estimate system mass. The low-thrust mission trajectory was analyzed and important Earth orbital environments were modeled. Baseline power system design options are recommended on the basis of performance, mass and risk/complexity. Important findings from parametric studies are discussed and the resulting impacts to the spacecraft design and cost.

Kerslake, Thomas W.↗