Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “parabolic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Complete flowfields over low and wide angle AOTV conceptual configurations

Flowfields over two conceptual aeroassisted orbital transfer vehicles, a moderate lift-to-drag ratio biconic, and an axisymmetric zero lift aerobrake are investigated. The solution procedures employ a compressible Navier-Stokes time-asymptotic technique for blunt body flow and a Parabolized Navier-Stokes spatial marching technique for the primarily supersonic shock layer flow over low-angle bodies. Emphasis is placed on the laminar convective heating predictions and comparisons to experimental data where available. Code robustness and solution times are discussed and guidelines are given for the specification of various numerical parameters. The Parabolized Navier-Stokes technique has a high probability of solution success for the range of applications considered herein, and very good comparisons with experimental heat-transfer data have been obtained. The blunt body Navier-Stokes code is more sensitive to parameter specification for the aerobrake calculations. Still, coarse grid solutions can be obtained quickly to get a good first cut at flowfield definition. Fair to good comparisons have been obtained between experimental heating and pressure data and coarse and fine grid solutions.

Gnoffo, P. A.↗
NASA NTRS1984

Thermal oxidation of 3C silicon carbide single-crystal layers on silicon

Thermal oxidation of thick single-crystal 3C SiC layers on silicon substrates was studied. The oxidations were conducted in a wet O2 atmosphere at temperatures from 1000 to 1250 C for times from 0.1 to 50 h. Ellipsometry was used to determine the thickness and index of refraction of the oxide films. Auger analysis showed them to be homogeneous with near stoichiometric composition. The oxide growth followed a linear parabolic relationship with time. Activation energy of the parabolic rate constant was found to be 50 kcal/mole, while the linear rate constant was 74 kcal/mole. The latter value corresponds approximately to the energy required to break a Si-C bond. Electrical measurements show an effective density of 4-6 x 10 to the 11th per sq cm for fixed oxide charges at the oxide-carbide interface, and the dielectric strength of the oxide film is aproximately 6 x 10 to the 6th V/cm.

Fung, C. D.↗
NASA NTRS1982

Propagation of wide bandwidth signals through strongly turbulent ionized media

Analytic and numerical techniques are presented which directly address the problem of propagation of wide bandwidth signals through random ionized media. This work is applicable to the problems of satellite communication and space based radar observation through a disturbed ionospheric propagation channel that would result from a high altitude chemical release or nuclear detonation. An analytic solution is presented for the two-position, two-frequency mutual coherence function for spherical wave propagation in the strong scattering limit. This solution is used to derive simple expressions for the power impulse response function and to determine its relationship to the important parameters of decorrelation distance and coherence bandwidth which describe the disturbed propagation channel. Results for mean time delay and time delay jitter are presented and compared to direct simulation results and to other theoretical calculations. A numerical/analytical solution to the parabolic wave equation is presented in the form of a multiple phase-screen (MPS) propagation simulation. In this very general solution technique, the random medium is divided into a finite number of layers. The field fluctuation through each layer is obtained by replacing the layer by a centrally located thin phase-screen, whose statistical properties are determined from the statistics of the electron-density irregularities. The waveform then propagates from phase-screen to phase-screen via an exact solution to the Fresnel-Kirchnoff equation. For wide bandwidth waveforms, numerical solutions are obtained at a number of discrete frequencies centered about the carrier and then time-domain solutions are obtained by Fourier transform techniques. Detailed results are presented for a number of interesting cases including propagation of a 20 MHz bandwidth signal through a finite barium cloud at a carrier frequency of 100 MHz. One of the major uses of the MPS propagation simulation has been to provide realizations of the received signal after propagation through a disturbed channel. The MPS simulation obtains a general solution of the parabolic wave equation under both weak and strong scattering conditions. A second technique to directly obtain realizations of wide bandwidth waveforms is presented here. This technique is limited to the case of strong scattering but requires only a fraction of the computer resources needed for MPS signal generation. Detailed comparisons of the two signal generation techniques are presented.

Random Media↗
NASA NTRS1985

Analysis of Satellite Communications Antenna Patterns

Computer program accurately and efficiently predicts far-field patterns of offset, or symmetric, parabolic reflector antennas. Antenna designer uses program to study effects of varying geometrical and electrical (RF) parameters of parabolic reflector and its feed system. Accurate predictions of far-field patterns help designer predict overall performance of antenna. These reflectors used extensively in modern communications satellites and in multiple-beam and low side-lobe antenna systems.

Rahmat-Samii, Y.↗
NASA NTRS1984

Transformation of two and three-dimensional regions by elliptic systems

The research during this period continued to expand the class of numerical algorithms that can be accurately and efficiently implemented on overlapping grids. Whereas previous calculations have been used to solve elliptic equations and to find the steady-state solution of parabolic equations, the present work is aimed towards developing time-accurate solution techniques for parabolic and hyperbolic equations. The primary difficulty here is in the correct treatment of the interior boundary nodes that must be updated at each iteration. The implementation of explicit methods is straightforward. However, the common practice of lagging these values when using an implicit methods leads to inconsistencies in the difference equation. One way to avoid this problem is to alternately calculate with an implicit and an explicit method on each subgrid. With this procedure, the explicit method generates boundary values at the next time level which are then used by the implicit step. It can be shown that when a backward implicit method is combined with a forward explicit method, the composite method is second order accurate and unconditionally stable for linear problems. A second area in which progress can be reported is in the distribution of grid points on curves and surfaces.

Mastin, E. W.↗
NASA NTRS1985

Effects of airfoil shape, thickness, camber, and angle of attack on calculated transonic unsteady airloads

The effects of airfoil shape, thickness, camber, and mean angle of attack on transonic unsteady airloads were investigated as calculated by the transonic small-disturbance computer code XTRAN2L. Shape effects were investigated by examining the pressure distributions, shock locations, and unsteady airloads for three 10 percent thick airfoils. NACA 0010, NACA 64A010, and parabolic arc. Thickness effects were determined by studying a single airfoil shape with three different thicknesses: NACA 0008, NACA 0010, and NACA 0012. Angle of attack and camber effects were studied by including mean angle of attack or by adding a simple parabolic camber distribution to the originally symmetric airfoils. Comparisons of unsteady airloads for different airfoil configurations show similar results caused by variations in airfoil shape, thickness, camber, or mean angle of attack. Computer costs can be reduced by limiting the number of transonic unsteady aerodynamic calculations for small changes in airfoil geometry or angle of attack.

Batina, J. T.↗
NASA NTRS1984

Prediction of the space adaptation syndrome

The univariate and multivariate relationships of provocative measures used to produce motion sickness symptoms were described. Normative subjects were used to develop and cross-validate sets of linear equations that optimally predict motion sickness in parabolic flights. The possibility of reducing the number of measurements required for prediction was assessed. After describing the variables verbally and statistically for 159 subjects, a factor analysis of 27 variables was completed to improve understanding of the relationships between variables and to reduce the number of measures for prediction purposes. The results of this analysis show that none of variables are significantly related to the responses to parabolic flights. A set of variables was selected to predict responses to KC-135 flights. A series of discriminant analyses were completed. Results indicate that low, moderate, or severe susceptibility could be correctly predicted 64 percent and 53 percent of the time on original and cross-validation samples, respectively. Both the factor analysis and the discriminant analysis provided no basis for reducing the number of tests.

Reschke, M. F.↗
NASA NTRS1985

Effects of chromium and aluminum on mechanical and oxidation properties of iron-nickel-base superalloys based on CG-27

The effects of chromium and aluminum on the mechanical and oxidation properties of a series of gamma-prime-strengthened alloys based on CG-27 were studied. Gamma-prime dispersion and solid-solution strengthening were the principal modes of alloy strengthening. The oxidation attack parameter K sub a decreased with increasing Cr and Al contents for each alloy group based on Al content. As a group, alloys with 3 wt % Al had the lowest attack parameters. Therefore, 3 wt % is the optimum level of Al for parabolic oxidation behavior. Spalling, due to diffusion-induced grain growth, was controlled by the overall Cr and Al levels. The alloy with 4 wt % Cr and 3 wt % Al had stress-rupture properties superior to those of the base alloy, CG-27, and maintained parabolic oxidation behavior while the Cr content was reduced by two-thirds of its value in cast CG-27.

Schuon, S. R.↗
NASA NTRS1985

Diffraction Analysis of Mesh Deployable Reflector Antennas

A formulation and many representative numerical results for mesh reflector antennas are presented. The reflection coefficient matrix for the prescribed mesh configuration was determined and the local coordinate system of the mesh cells at each point on the curved reflector surface was accentuated. A novel strip aperture model was used to formulate the transmission coefficient matrix for a variety of mesh cell configurations. Numerical data are tailored to the dimensions of a conceptually designed land mobile satellite system (LMSS) which employs a large mesh deployable offset parabolic antenna. Results are shown for an offset parabolic reflector with mesh surfaces similar to the mesh surface of tracking and data relay satellite system (TDRSS).

Rahmat-Samii, Y.↗
NASA NTRS1985

Activity and accomplishments of dish/Stirling electric power system development

The development of the solar parabolic-dish/Stirling-engine electricity generating plant known as the dish/Stirling electric power system is described. The dish/Stirling electric power system converts sunlight to electricity more efficiently than any known existing solar electric power system. The fabrication and characterization of the test bed concentrators that were used for Stirling module testing and of the development of parabolic dish concentrator No. 2, an advanced solar concentrator unit considered for use with the Stirling power conversion unit is discussed.

Livingston, F. R.↗
NASA NTRS1985

Review - Computational methods for internal flows with emphasis on turbomachinery

Current computational methods for analyzing flows in turbomachinery and other related internal propulsion components are presented. The methods are divided into two classes. The inviscid methods deal specifically with turbomachinery applications. Viscous methods, deal with generalized duct flows as well as flows in turbomachinery passages. Inviscid methods are categorized into the potential, stream function, and Euler approaches. Viscous methods are treated in terms of parabolic, partially parabolic, and elliptic procedures. Various grids used in association with these procedures are also discussed.

Mcnally, W. D.↗
NASA NTRS1985

Implicit/explicit analysis of interactive phenomena in: supersonic, chemically-reacting, mixing and boundary layer problems

An efficient implicit/explicit procedure for solving the parabolized Navier-Stokes (PNS) equations to analyze supersonic, viscous, chemically-reacting flows is presented. The approach combines a fully-implicit algorithm for solving the parabolic mixing/boundary layer equations with an explicit algorithm for determining the hyperbolic pressure field. The unified model, SPLITP, contains provisions for treating bounding/embedded subsonic regions using a pressure-splitting procedure which suppresses elliptic (upstream influence) effects without recourse to sublayer approximations. Several two-equation turbulence models with compressibility and curvature-correction terms are incorporated into SPLITP. Applications to a variety of flow problems are presented which include: ducted supersonic mixing and combustion flowfields, free jets and plumes, and, curved boundary layers and wall jets.

Dash, S. M.↗
NASA NTRS1986

Head movements in non-terrestrial force environments elicit motion sickness - Implications for the etiology of space motion sickness

Space motion sickness has become an operational concern in manned space flight. Considerable evidence exists that head movements in free fall, especially pitch movements, are provocative until adaptation occurs. The question arises whether space motion sickness is an unique nosological entity or is due to body movements in a nonterrestrial force environment, a force environment for which the body's dynamic sensory-motor adaptions to 1 G are no longer appropriate. To evaluate this issue, subjects were asked to make controlled head movements during exposure to high gravitoinertial force levels, 1.8-2.0 G, in parabolic flight maneuvers. Head movements in pitch with eyes open were most evocative of motion sickness, yaw movements with eyes covered were least provocative. This pattern is identical to that which occurs when the same types of head movements are made in the free fall phase of parabolic maneuvers. It appears that space motion sickness is the consequence of prolonged exposure to a nonterrestrial force background rather than of exposure to free fall per se.

Lackner, J. R.↗
NASA NTRS1986

Oxidation and embrittlement of Ti-6Al-2Sn-4Zr-2Mo alloy

A thermogravimetric analysis monitoring study has been conducted for Ti-6Al-2Sn-4Zr-2Mo in the 593-760 C range, with a view to its total oxidation kinetics in laboratory air. In addition, tensile elongation was obtained for selected foil specimens after their exposure to simulated Space Shuttle reentry conditions. The total weight gain with time exhibited two parabolic stages separated by a transient region which is the result of a simultaneous increase in the parabolic growth rate constant for the oxide and in oxygen solubility at the oxide-metal interface. A model for the total oxidation kinetics accounting for the two individual components (oxide growth and solid solution formation) is proposed; the activation energy for oxygen diffusion in the alpha-solid solution is shown to approximate the activation energy for the degradation of tensile elongation of the alloy in its foil gage condition.

Shenoy, R. N.↗
NASA NTRS1986

Q3DG: A computer program for strain-energy-release rates for delamination growth in composite laminates

The Q3DG is a computer program developed to perform a quasi-three-dimensional stress analysis for composite laminates which may contain delaminations. The laminates may be subjected to mechanical, thermal, and hygroscopic loads. The program uses the finite element method and models the laminates with eight-noded parabolic isoparametric elements. The program computes the strain-energy-release components and the total strain-energy release in all three modes for delamination growth. A rectangular mesh and data file generator, DATGEN, is included. The DATGEN program can be executed interactively and is user friendly. The documentation includes sections dealing with the Q3D analysis theory, derivation of element stiffness matrices and consistent load vectors for the parabolic element. Several sample problems with the input for Q3DG and output from the program are included. The capabilities of the DATGEN program are illustrated with examples of interactive sessions. A microfiche of all the examples is included. The Q3DG and DATGEN programs have been implemented on CYBER 170 class computers. Q3DG and DATGEN were developed at the Langley Research Center during the early eighties and documented in 1984 to 1985.

Raju, I. S.↗
NASA NTRS1986

Property of radially quadratic reflector systems

This report shows that when considered in terms of optical geometry, radially parabolic and radially hyperbolic mirrors used as mirrors for Cassegrain and parabolic antennas possess values similar to common conical horn reflector antennas.

Mizusawa, M.↗
NASA NTRS1986

X-ray telescope module for the LAMAR Space Shuttle experiment

The first of eight X-ray telescopes is under construction for the LAMAR experiment. Each consists of two orthogonal sets of nested confocal one-dimensional parabolic plates of gold-coated float glass, selected for flatness from commercial stock. Each is initially bent to a cylinder by bonding a thin, highly curved titanium sheet to its inactive surface. The final parabolic figure is produced by an automated system which includes seven diode arrays that detect a visible-light line image. Eight precise motorized linear translators operating under the control of a computer, tune the plate to the optimum figure. The plate is then fixed in position by epoxy bonds. The precision of the system is several arcsec, but the intrinsic flatness of the glass is expected to limit the half-power diameter (HPD) of the telescope to about 25 arcsec.

Gorenstein, P.↗
NASA NTRS1987

The electron distribution function upstream from the earth's bow shock

A general analytic theory for the distribution function of particles backstreaming from an arbitrary shock in a magnetized plasma is presented. Particle motions are shown to be restricted to two-dimensional planes. A general form for the source term describing upstreaming particles accelerated at the shock is presented along with explicit source terms for planar and parabolic shocks. The origin and form of the escape velocity cutoff for a shock in a magnetized plasma are discussed. The distribution function upstream of a finite planar shock and a parabolic shock in two dimensions is calculated, and an analytic approximation of the cutoff velocity at points in the upstream region is derived. The theory is then applied to the earth's bow shock, calculating distribution functions and the nature and spatial variation of the cutoff velocity. The theory for the particle distribution upstream of the bow shock is compared with the model of Filbert and Kellogg (1979).

Cairns, Iver H.↗