Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “oxide interface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Extending the Service Life of High–Ni Layered Oxides by Tuning the Electrode–Electrolyte Interphase

As a high-energy-density cathode for Li-ion batteries, high-Ni layered oxides, especially with ultrahigh Ni-content, suffer from short lifespans, due in part to their unstable electrode–electrolyte interphase (EEI). Herein, the cycle life of LiNi 0.94 Co 0.06 O 2 is greatly extended by manipulating the EEI with a lithium bis(oxalate) (LiBOB) additive even when operated at a moderately high voltage (4.4 V vs Li/Li + ). Impressively, the capacity retention can be increased from 61 to 80% after 500 cycles in a full cell paired with a graphite anode. Additionally, the presence of LiBOB enables a robust boron- and oxygen-enriched EEI that effectively inhibits continual electrolyte decomposition and offers a stable cathode surface. Moreover, the layered architecture of the cathode–electrolyte interphase (CEI) and the anode–electrolyte interphase (AEI) at the nanometer scale is revealed by time-of-flight secondary ion mass spectrometry. It is demonstrated that the cathode surface chemistry can significantly influence the AEI both chemically and physically, and AEI is modified from a thick “three-layer” to a thin “two-layer” architecture by tuning the cathode surface chemistry with LiBOB. Finally, this work presents a correlation between the EEI characteristics and battery performance and highlights the significance of manipulating surface chemistry in developing stable high-energy-density Li-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Enhanced tunability of two-dimensional electron gas on SrTiO 3 through heterostructuring

Two-dimensional electron gases (2DEGs) on the SrTiO 3 (STO) surface or in STO-based heterostructures have exhibited many intriguing phenomena, which are strongly dependent on the 2DEG-carrier density. In this paper, we report that the tunability of the 2DEG-carrier density is significantly enhanced by adding a monolayer LaTiO 3 (LTO) onto the STO. Ultraviolet (UV) irradiation induced maximum carrier density of the 2DEG in LTO/STO is increased by a factor of ~4 times, compared to that of the bare STO. By oxygen gas exposure, it becomes 10 times smaller than that of the bare STO. This enhanced tunability is attributed to the drastic surface property change of a polar LTO layer by UV irradiation and O 2 exposure. This indicates that the 2DEG controllability in LTO/STO is more reliable than that on the bare STO driven by defects, such an oxygen vacancy.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Compatibility of Zircaloy-4 in eutectic PbSn and PbBiSn liquid metals

Here, a novel nuclear fuel concept has been proposed, consisting of UO₂ particles suspended in a liquid metal alloy. To evaluate its feasibility, the compatibility of Zircaloy-4 cladding with candidate eutectic PbSn and PbBiSn alloys—as well as with pure Pb, Bi, and Sn—was investigated through 1000-hour exposures at 400 °C and 600 °C. Severe degradation of the Zircaloy-4 specimens was observed in eutectic PbSn at 600 °C, whereas oxidation and oxygen diffusion were evident after exposure at 400 °C. At 600 °C, the formation of Zr₃Fe precipitates at the oxide–alloy interface was identified in specimens exposed to Pb and PbBiSn. Thermodynamic analysis suggested that the observed intermetallic formation resulted from the destabilization of Laves phases due to oxygen ingress at elevated temperatures.

Bismuth↗
DOE OSTI2020

Wear Performance of incoloy 800HT and inconel 617 in various surface conditions for high-temperature gas-cooled reactor components

Incoloy™ 800HT and Inconel™ 617 are primary candidate structural materials for high-temperature gas-cooled reactors (HTGRs). Impurities (e.g., H 2 O, CH 4 ) in the coolant induce corrosion reactions that affect tribological behavior. We investigate the high-temperature tribological performance of the alloys under surface conditions including: conditioned in H 2 O-containing helium at elevated temperatures, hardened via the carbon-diffusion Kolsterising® treatment, and conditioned after hardening. Initial friction coefficients and volume removed serve as metrics for wear performance. In this work, we find that wear mechanisms including scuffing, glaze-oxide formation, and oxide-layer wear and break-through are governed by surface hardness, chemistry, and applied load. The formation of a glaze-oxide layer is achieved with an oxide of sufficient mechanical integrity if the oxide-substrate interface is strong and the load is low.

42 ENGINEERING↗
DOE OSTI2024

Composition-Dependent Reconstructions of Titanium Oxide Clusters and Cu(111) Support via Cluster-Adatom Interactions

Mass-selected cluster deposition and scanning tunneling microscopy (STM) were used to investigate the surface structure and thermal stability of Ti 3 O y (y = 5, 6) clusters on a Cu(111) surface. STM imaging shows that the substoichiometric Ti 3 O 5 clusters aggregate into large dendritic assemblies at step edges, while the stoichiometric Ti 3 O 6 clusters are highly dispersed as single or small groupings of clusters. Cluster deposition also results in extensive reconstruction of the Cu(111) surface. The Ti 3 O 5 /Cu(111) surface exhibits one Cu-layer deep pits that are ringed by cluster assemblies that nucleate and grow at the perimeter step edges. By comparison, the Ti 3 O 6 /Cu(111) surface consists of irregular step edges and small one Cu-layer islands that are decorated with clusters. The restructuring of the Cu(111) surface is attributed to strong Cu-cluster interactions that release Cu adatoms from the step edges. This mechanism is supported by density functional theory (DFT) calculations, which predict that the Cu adatom attachment to the clusters is energetically favorable. Annealing the surfaces at elevated temperatures (400-700 K) results in higher densities of irregular steps, pits and isolated Cu islands as well as increased cluster aggregation. In conclusion, this work highlights adatom-cluster interactions as another manifestation of strong cluster-support interactions that can significantly alter the nature of the oxide-metal interface.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2026

A Quantum Mechanical Study of Quartz (101) Interfacial Boundaries

Density functional theory (DFT) calculations were performed on periodic and molecular models to explore the energetics of bonding modes at quartz–quartz interfaces, common grain contacts in sandstones. Four interface types were modeled: H 2 O-mediated, silanol H-bond mediated, O–O peroxide bonds, and siloxane bonds. Each type of interface may exist in the subsurface of the Earth, depending upon water activity, temperature, and pressure, as interfacial structures are stable within DFT molecular dynamics simulations up to 473 K. The results predict interfacial energies SiOSi > SiOOSi > SiOH-6H 2 O > 2SiOH, as expected based on similar bond strengths in other systems. The proposed SiOOSi interface is not generally accounted for in chemomechanical models but could be important in sandstones at depth in the Earth. The implications for intergrain fracturing and H2 generation are discussed.

Hydrogen↗
DOE OSTI2022

Genesis of Nanogalvanic Corrosion Revealed in Pearlitic Steel

Nanoscale, localized corrosion underpins billions of dollars in damage and material costs each year; however, the processes responsible have remained elusive due to the complexity of studying degradative material behavior at nanoscale liquid–solid interfaces. Recent improvements to liquid cell scanning/transmission electron microscopy and associated techniques enable this first look at the nanogalvanic corrosion processes underlying this widespread damage. Nanogalvanic corrosion is observed to initiate at the near-surface ferrite/cementite phase interfaces that typify carbon steel. In minutes, the corrosion front delves deeper into the material, claiming a thin layer of ferrite around all exposed phase boundaries before progressing laterally, converting the ferrite to corrosion product normal to each buried cementite grain. Over the following few minutes, the corrosion product that lines each cementite grain undergoes a volumetric expansion, creating a lateral wedging force that mechanically ejects the cementite grains from their grooves and leaves behind percolation channels into the steel substructure.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Unveiling the Interfacial Reconstruction Mechanism Enabling Stable Growth of the Delafossite PdCoO 2 on Al 2 O 3 and LaAlO 3

Delafossites, composed of noble metal (A + ) and strongly correlated sublayers (BO 2 – ), form natural superlattices with highly anisotropic properties. These properties hold significant promise for various applications, but their exploitation hinges on the successful growth of high-quality thin films on suitable substrates. Unfortunately, the unique lattice geometry of delafossites presents a significant challenge to thin-film fabrication. Different delafossites grow differently, even when deposited on the same substrate, ranging from successful epitaxy to complete growth suppression. These variations often lack a clear correlation to obvious causes like lattice mismatch. Unidentified stabilization mechanisms appear to enable growth in certain cases, allowing these materials to form stable thin films or act as buffer layers for subsequent delafossite growth. This study employs advanced scanning transmission electron microscopy techniques to investigate the nucleation mechanism underlying the stable growth of PdCoO 2 films on Al 2 O 3 and LaAlO 3 substrates grown via molecular-beam epitaxy. Our findings reveal the presence of a secondary phase within the substrate surface that stabilizes the films. This mechanism deviates from the conventional understanding of strain relief mechanisms at oxide heterostructure interfaces and differs significantly from those observed for Cu-based delafossites.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Surface-Active ß-Caryophyllene Oxidation Products at the Air/Aqueous Interface

We examine synthesized standards of structurally related ß-caryophyllene ozonolysis products at the air/water and air/(NH4)2SO4 (aq) interface using polarization-resolved standard- and high-resolution vibrational sum frequency generation (SFG) spectroscopy in the C–H and O–H stretching regions. ß-Caryophyllene aldehyde (1), the most surface-active molecule in the suite, appears to undergo a change in its molecular orientation distribution when transitioning from low to high relative surface coverage. We also report that the water molecules present at the outermost layer of the aqueous interface are displaced by ß-caryophyllene aldehyde (1) on both the (NH4)2SO4 (aq) and water subphases. Additionally, the more weakly hydrogen-bonded water network observed around ~3400 cm-1 seems to be perturbed to a greater extent by ß-caryophyllene aldehyde (1) than the more strongly hydrogen-bonded population observed at ~3200 cm-1 on the (NH4)2SO4 (aq) subphase, while this effect is not observed on the water subphase. We provide surface spectroscopic evidence for the “salting out” effect of (NH4)2SO4 in aqueous environments and discuss the implications for understanding the organization of surface-localized molecules present in aqueous cloud-forming droplets containing dissolved aerosol cloud condensation nuclei (CCN) in the atmosphere. Despite the importance of elucidating the surface activity and interfacial organization of individual molecules in aqueous media, future work will focus on how the combined effects of several surface-active constituents dictate overall cloud activation potentials of aerosol particles.

Sum frequency generation (SFG) spectroscopy, ?-car↗
DOE OSTI2024

Dynamic Bubbling Balanced Proactive CO 2 Capture and Reduction on a Triple-Phase Interface Nanoporous Electrocatalyst

The formation and preservation of the active phase of the catalysts at the triple-phase interface during CO 2 capture and reduction is essential for improving the conversion efficiency of CO 2 electroreduction toward value-added chemicals and fuels under operational conditions. Designing such ideal catalysts that can mitigate parasitic hydrogen generation and prevent active phase degradation during the CO 2 reduction reaction (CO 2 RR), however, remains a significant challenge. Herein, we developed an interfacial engineering strategy to build a new SnO x catalyst by invoking multiscale approaches. This catalyst features a hierarchically nanoporous structure coated with an organic F-monolayer that modifies the triple-phase interface in aqueous electrolytes, substantially reducing competing hydrogen generation (less than 5%) and enhancing CO 2 RR selectivity (~90%). This rationally designed triple-phase interface overcomes the issue of limited CO 2 solubility in aqueous electrolytes via proactive CO 2 capture and reduction. Concurrently, we utilized pulsed square-wave potentials to dynamically recover the active phase for the CO 2 RR to regulate the production of C1 products such as formate and carbon monoxide (CO). This protocol ensures profoundly enhanced CO 2 RR selectivity (~90%) compared with constant potential (~70%) applied at -0.8 V (V vs RHE). We further achieved a mechanistic understanding of the CO 2 capture and reduction processes under pulsed square-wave potentials via in situ Raman spectroscopy, thereby observing the potential-dependent intensity of Raman vibrational modes of the active phase and CO 2 RR intermediates. Finally, this work will inspire material design strategies by leveraging triple-phase interface engineering for emerging electrochemical processes, as technology moves toward electrification and decarbonization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Defect-driven selective metal oxidation at atomic scale

Nanoscale materials modified by crystal defects exhibit significantly different behaviours upon chemical reactions such as oxidation, catalysis, lithiation and epitaxial growth. However, unveiling the exact defect-controlled reaction dynamics (e.g. oxidation) at atomic scale remains a challenge for applications. Here, using in situ high-resolution transmission electron microscopy and first-principles calculations, we reveal the dynamics of a general site-selective oxidation behaviour in nanotwinned silver and palladium driven by individual stacking-faults and twin boundaries. The coherent planar defects crossing the surface exhibit the highest oxygen binding energies, leading to preferential nucleation of oxides at these intersections. Planar-fault mediated diffusion of oxygen atoms is shown to catalyse subsequent layer-by-layer inward oxide growth via atomic steps migrating on the oxide-metal interface. These findings provide an atomistic visualization of the complex reaction dynamics controlled by planar defects in metallic nanostructures, which could enable the modification of physiochemical performances in nanomaterials through defect engineering.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Evidence for non-electrostatic interactions between a pyrophosphate-functionalized uranyl peroxide nanocluster and iron (hydr)oxide minerals

We report the terminal oxygen atoms of the pyrophosphate groups in the uranyl peroxide nanocluster U 24 Pp 12 ([(UO 2 ) 24 (O 2 ) 24 (P 2 O 7 ) 12 ] 48- ) are not fully satisfied by bond valence considerations and can become protonated. This functionality could allow for specific interactions with mineral surfaces, as opposed to the electrostatically-driven interactions observed between non-functionalized uranyl peroxide nanoclusters and mineral surfaces. The sorption of U 24 Pp 12 to goethite and hematite was studied using batch sorption experiments as a function of U 24 Pp 12 concentration, mineral concentration, and pH. A suite of spectroscopic techniques, scanning electron microscopy, and electrophoretic mobility measurements were used to examine the minerals before and after reaction with U 24 Pp 12 , leading to a proposed conceptual model for U 24 Pp 12 interactions with goethite. The governing rate laws were determined and compared to those previously determined for a non-functionalized uranyl peroxide nanocluster. The rate of uranyl peroxide nanocluster sorption depends on the charge density and functionalized component of the uranyl peroxide cage. Electrophoretic mobility and attenuated total reflectance Fourier transform infrared spectroscopy analyses show that an inner-sphere complex forms between the U 24 Pp 12 cluster and the goethite surface through the terminal pyrophosphate groups, leading to a proposed conceptual model in which U 24 Pp 12 interacts with the triply-coordinated reactive sites on the (110) plane of goethite. Finally, these results demonstrate that the behavior of U 24 Pp 12 at the iron (hydr)oxide-water interface is unique relative to interactions of the uranyl ion and non-functionalized uranyl peroxide nanoclusters.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2014

Enhancement of thermal stability and water resistance in yttrium-doped GeO{sub 2}/Ge gate stack

We have systematically investigated the material and electrical properties of yttrium-doped GeO{sub 2} (Y-GeO{sub 2}) on Germanium (Ge). A significant improvement of both thermal stability and water resistance were demonstrated by Y-GeO{sub 2}/Ge stack, compared to that of pure GeO{sub 2}/Ge stack. The excellent electrical properties of Y-GeO{sub 2}/Ge stacks with low D{sub it} were presented as well as enhancement of dielectric constant in Y-GeO{sub 2} layer, which is beneficial for further equivalent oxide thickness scaling of Ge gate stack. The improvement of thermal stability and water resistance are discussed both in terms of the Gibbs free energy lowering and network modification of Y-GeO{sub 2}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗