Lattice dynamics of BaFe2X3(X = S, Se) compounds
Explore the source record for details and available documents.
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Explore the source record for details and available documents.
In the present work, cast Al-5Zn-2Mg alloy was processed through equal-channel angular pressing (ECAP) in route B{sub C} up to four number of passes. Microstructure and mechanical properties were investigated on processed and unprocessed materials. In cast condition, the material was composed of dendritic structure. After homogenization treatment, large-sized grains were observed. After ECAP processing, significant grain refinement was observed. After ECAP processing, high-density dislocations and high degree of misorientation between the grains were observed. In cast material, rod-shaped precipitates were observed, while, after ECAP processing, spherical-shaped precipitates were observed. ECAP processing leads to a noticeable improvement in the mechanical properties of the material. After four passes, 122% improvement in the microhardness and 135% improvement in the ultimate tensile strength of the material were observed. After three passes, a slight decrease in the mechanical properties was observed. This is attributed to the dissolution of the metastable η′ phase, annihilation of dislocations, dynamic recrystallization and texturing during ECAP processing. Brittle fracture mode was observed in tensile testing cast and homogenized samples. After ECAP processing, fracture mode was changed into shear fracture mode.
Cu{sub 1-x}Sn{sub x}O(x = 0.00, 0.03, and 0.05) nanoflakes were synthesized by a simple wet chemical method and X-Ray diffraction (XRD) result confirms the monoclinic structure of CuO with no secondary phases due to Sn doping. The scanning electron microscopic images indicate the formation of nanoflakes. The fundamental Raman modes were observed at 273, 318, 610, and 1084 cm{sup -1} for undoped CuO sample and theses modes were slightly shifted towards lower frequency side for Sn-doped samples, which indicates the inclusion of Sn in CuO. In addition, XRD and Raman studies infer the decrease of crystallinity in doped samples, which is reflected in the sensitivity towards ethanol. The ethanol sensitivity (resistivity measurement) increases with ethanol gas concentration and decreases with Sn-doping in CuO nanoflakes.
A measurement of the intensity distribution in an image of the solar disk will be corrupted by a spatial redistribution of the light that is caused by the earth's atmosphere and the observing instrument. A simple correction method is introduced here that is applicable for solar p-mode intensity observations obtained over a period of time in which there is a significant change in the scattering component of the point spread function. The method circumvents the problems incurred with an accurate determination of the spatial point spread function and its subsequent deconvolution from the observations. The method only corrects the spherical harmonic coefficients that represent the spatial frequencies present in the image and does not correct the image itself.
We have observed that the disparate scale nonlinear interactions between the high-frequency (∼0.4 MHz) electron temperature gradient (ETG) mode and the ion-scale low-frequency fluctuations (∼kHz) were enhanced when the amplitude of the ETG mode exceeded a certain threshold. The dynamics of nonlinear coupling between the ETG mode and the drift wave (DW) mode has already been reported [C. Moon, T. Kaneko, and R. Hatakeyama, Phys. Rev. Lett. (2013)]. Here, we have newly observed that another low-frequency fluctuation with f ≃ 3.6 kHz, i.e., the flute mode, was enhanced, corresponding to the saturation of the DW mode growth. Specifically, the bicoherence between the flute mode and the DW mode reaches a significant level when the ∇T{sub e}/T{sub e} strength exceeded 0.54 cm{sup −1}. Thus, it is shown that the ETG mode energy was transferred to the DW mode, and then the energy was ultimately transferred to the flute mode, which was triggered by the disparate scale nonlinear interactions between the ETG and ion-scale low-frequency modes.
The observation of single mode propagation in an air-clad single crystal sapphire optical fiber at wavelengths at and above 783 nm is presented for the first time. A high-temperature wet acid etching method was used to reduce the diameter of a 10 cm length of commercially-sourced sapphire fiber from 125 micrometers to 6.5 micrometers, and far-field imaging provided modal information at intervals as the fiber diameter decreased. Modal volume was shown to decrease with decreasing diameter, and single mode behavior was observed at the minimum diameter achieved. While weakly-guiding approximations are generally inaccurate for low modal volume optical fiber with high core-cladding refractive index disparity, consistency between these approximations and experimental results was observed when the effective numerical aperture was measured and substituted for the theoretical numerical aperture in weakly-guiding approximation calculations. With the demonstration of very low modal volume in sapphire at fiber diameters much larger than anticipated by legacy calculations, the resolution of sapphire fiber distributed sensors may be increased and other sensing schemes requiring very low modal volume, such as fiber Bragg gratings, may be realized in extreme environment applications.
The angular anisotropy of interface phonons and their interaction with optical phonons in (001) GaAs/AlAs superlattices are calculated and experimentally studied. Experiments were performed by Raman light scattering in different scattering geometries for phonons with the wave vector directed normally to the superlattice and along its layers. Phonon frequencies were calculated by the extended Born method taking the Coulomb interaction into account in the rigid-ion approximation. Raman scattering spectra were calculated in the Volkenshtein bond-polarizability approximation. Calculations confirmed that the angular anisotropy of phonons observed in experiments appears due to interaction (mixing) of optical phonons, in which atoms are mainly displaced normally to superlattices, with interface phonons (TO-IF modes). In the scattering geometry, when the wave vector lies in the plane of superlattice layers, the mixed TO-IF modes are observed under nonresonance conditions. The Raman spectra for TO-IF modes depend on the mixing of atoms at heteroboundaries.
We have utilized the NASA/IRTF 3 m SpeX instrument’s high-resolution spectral mode to observe and characterize the near-infrared flux emanating from the unusual Kepler light curve system KIC 8462852. By comparing the resulting 0.8–4.2 μm spectrum to a mesh of model photospheric spectra, the 6 emission line analyses of the Rayner et al. catalog, and the 25 system collections of debris disks we have observed to date using SpeX under the Near InfraRed Debris disk Survey, we have been able to additionally characterize the system. Within the errors of our measurements, this star looks like a normal solar abundance main-sequence F1V to F3V dwarf star without any obvious traces of significant circumstellar dust or gas. Using Connelley and Greene’s emission measures, we also see no evidence of significant ongoing accretion onto the star nor any stellar outflow away from it. Our results are inconsistent with large amounts of static close-in obscuring material or the unusual behavior of a YSO system, but are consistent with the favored episodic giant comet models of a Gyr old stellar system favored by Boyajian et al. We speculate that KIC 8462852, like the ∼1.4 Gyr old F2V system η Corvi, is undergoing a late heavy bombardment, but is only in its very early stages.
Alloy nanorods consisting of bimetallic gold and silver are synthesized by employing the electrochemical codeposition of Au/Ag alloy materials into the pores of anodized aluminum oxide templates. This paper presents the variation of localized surface plasmon resonance (LSPR) modes of the Au{sub x}/Ag{sub 1-x} alloy nanorods as a function of relative compositions of Au and Ag. Transverse and multiple longitudinal modes were observed when the length was longer than ca. 300 nm. For a given length, the transverse LSPR mode systematically blue-shifted as the Ag portion increased, while there was little variation in peak positions of the longitudinal LSPR modes. The optical properties of the Au{sub x}/Ag{sub 1-x} alloy nanorods were calculated using the discrete dipole approximation and showed a good agreement with the experimental measurements.
A planar magnetron sputtering device with thermally isolated sintered boron target has been designed and demonstrated. The magnetron is intended to use for generation of boron ion beams, as well as in plasma immersion implantation. For a boron target, high target temperature is required because boron has low electrical conductivity at room temperature, which increases with temperature. The target is well insulated thermally and can be heated by an initial low-current, high-voltage DC discharge mode. A discharge power of 16 W was adequate to reach the required surface temperature, after that a transition of the discharge to a high-current, low-voltage mode is observed. Applying high current pulses over the DC heating discharge results in a self-sputtering operational mode of the magnetron discharge. Ion beam was extracted from the discharge plasma. Beam analysis was performed with a time-of-flight system. All the boron ions are single charged. The maximum boron ion fraction in the beam is greater than 99%, and the mean boron ion fraction, time-integrated over the whole pulse length, is about 95%. This kind of boron ion source could be competitive to conventional boron ion sources that utilize compounds such as BF{sub 3}, and could be useful for semiconductor industry application.
Dynamics of flexible non-Brownian fibers in shear flow at low-Reynolds-number are analyzed numerically for a wide range of the ratios A of the fiber bending force to the viscous drag force. Initially, the fibers are aligned with the flow, and later they move in the plane perpendicular to the flow vorticity. A surprisingly rich spectrum of different modes is observed when the value of A is systematically changed, with sharp transitions between coiled and straightening out modes, period-doubling bifurcations from periodic to migrating solutions, irregular dynamics, and chaos.
Inelastic neutron scattering is used to measure the temperature-dependent phonon dispersion in Ca{sub 2-x}Sr{sub x}RuO{sub 4} (x = 0.4,0.6). The in-plane {Sigma}{sub 4} octahedral tilt mode softens significantly at the zone boundary of the high-temperature tetragonal (HTT) I4{sub 1}/acd structure as the temperature approaches the transition to a low-temperature orthorhombic (LTO) Pbca phase. This behavior is similar to that in La{sub 2}CuO{sub 4}, but an inelastic feature that is not found in the cuprate is present. An anomalous phonon mode is observed at energy transfers greater than the {Sigma}{sub 4}, albeit with similar dispersion. This anomalous phonon mode never softens below {approx} 5 meV, even for temperatures below the HTT-LTO transition. This mode is attributed to the presence of intrinsic structural disorder within the I4{sub 1}/acd tetragonal structure of the doped ruthenate.
We have measured the bias voltage and field dependence of eigenmode frequencies in a magnetic tunnel junction with MgO barrier. We show that both free layer (FL) and reference layer (RL) modes are excited, and that a crossover between these modes is observed by varying external field and bias voltage. The bias voltage dependence of the FL and RL modes are shown to be dramatically different. The bias dependence of the FL modes is linear in bias voltage, whereas that of the RL mode is strongly quadratic. Using modeling and micromagnetic simulations, we show that the linear bias dependence of FL frequencies is primarily due to a linear dependence of the perpendicular spin torque on bias voltage, whereas the quadratic dependence of the RL on bias voltage is dominated by the reduction of exchange bias due to Joule heating, and is not attributable to a quadratic dependence of the perpendicular spin torque on bias voltage.
The plasma waves associated with the magnetotail flux ropes of December 28, 1982, December 30, 1982, and March 25, 1983, originally identified by Sibeck et al. (1984) are studied. Broadband electrostatic noise was found in the sheaths and cores of all three flux ropes. The frequency range extended from about 100 Hz to the local electron plasma frequency. The electric field vector tended to be aligned either parallel or antiparallel to the local magnetic field direction throughout the complex flux rope magnetic field configuration. The March 25, 1983, flux rope also contained an intense band of whistler mode noise extending up to one half the local electron cyclotron frequency. The superthermal electrons generating the observed whistler mode noise may have had highly anisotropic pitch angle distributions.
Electron gyroscale fluctuation measurements in National Spherical Torus Experiment H-mode plasmas with large toroidal rotation reveal fluctuations consistent with electron temperature gradient (ETG) turbulence. Large toroidal rotation in National Spherical Torus Experiment plasmas with neutral beam injection generates ExB flow shear rates comparable to ETG linear growth rates. Enhanced fluctuations occur when the electron temperature gradient is marginally stable with respect to the ETG linear critical gradient. Fluctuation amplitudes decrease when the ExB flow shear rate exceeds ETG linear growth rates. The observations indicate that ExB flow shear can be an effective suppression mechanism for ETG turbulence.
We report on narrowband electromagnetic waves at frequencies between the local electron cyclotron and lower hybrid frequencies observed by the Mars Atmosphere and Volatile EvolutioN (MAVEN) spacecraft in the Martian induced magnetosphere. The peaked electric field wave spectra below the electron cyclotron frequency were first observed by Phobos-2 in the Martian magnetosphere, but the lack of magnetic field wave data prevented definitive identification of the wave mode and their generation mechanisms remain unclear. Analysis of electric and magnetic field wave spectra obtained by MAVEN demonstrates that the observed narrowband waves have properties consistent with the whistler mode. Linear growth rates computed from the measured electron velocity distributions suggest that these whistler mode waves can be generated by cyclotron resonance with anisotropic electrons. Large electron anisotropy in the Martian magnetosphere is caused by absorption of parallel electrons by the collisional atmosphere. The narrowband whistler mode waves and anisotropic electrons are observed on both open and closed field lines and have similar spatial distributions in MSO and planetary coordinates. Some of the waves on closed field lines exhibit complex frequency-time structures such as discrete elements of rising tones and two bands above and below half the electron cyclotron frequency. These MAVEN observations indicate that whistler mode waves driven by anisotropic electrons, which are commonly observed in intrinsic magnetospheres and at unmagnetized airless bodies, are also present at Mars. The wave-induced electron precipitation into the Martian atmosphere should be evaluated in future studies.
Spin-wave dynamics in 30 nm thick Co{sub 2}Fe{sub 1−x}Mn{sub x}Al full-Heusler films is investigated using time-resolved magneto-optical polar Kerr spectroscopy under an external field perpendicular to films. Damon-Eshbach (DE) and the first-order perpendicular standing spin-wave (PSSW) modes are observed simultaneously in four samples with x = 0, 0.3, 0.7, and 1. The frequency of DE and PSSW modes does not apparently depend on composition x, but damping of DE mode significantly on x and reaches the minimum as x = 0.7. The efficient coherent excitation of DE spin wave exhibits the promising application of Co{sub 2}Fe{sub 0.3}Mn{sub 0.7}Al films in magnonic devices.
A non-standing characteristic of directly imaged spin-waves in confined micrometer-sized ultrathin Permalloy (Ni 80 Fe 20 ) structures is reported along with evidence of the possibility to alter the observed state by modifications to the sample geometry. Using micromagnetic simulations, the presence of the spin-wave modes excited in the Permalloy stripes along with the quasi-uniform modes was observed. The predicted spin-waves were imaged in direct space using time resolved scanning transmission x-ray microscopy, combined with a ferromagnetic resonance excitation scheme (STXM-FMR). STXM-FMR measurements revealed a non-standing characteristic of the spin-waves. Also, it was shown by micromagnetic simulations and confirmed using STXM-FMR results that the observed characteristic of the spin-waves can be influenced by the local magnetic fields in different sample geometries.