Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “nonlinear response”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Study of the effect of static/dynamic Coulomb friction variation at the tape-head interface of a spacecraft tape recorder by non-linear time response simulation

A description is presented of six simulation cases investigating the effect of the variation of static-dynamic Coulomb friction on servo system stability/performance. The upper and lower levels of dynamic Coulomb friction which allowed operation within requirements were determined roughly to be three times and 50% respectively of nominal values considered in a table. A useful application for the nonlinear time response simulation is the sensitivity analysis of final hardware design with respect to such system parameters as cannot be varied realistically or easily in the actual hardware. Parameters of the static/dynamic Coulomb friction fall in this category.

Mukhopadhyay, A. K.↗
DOE OSTI2021

Bulk Photovoltaic Effect Driven by Collective Excitations in a Correlated Insulator

We investigate the bulk photovoltaic effect, which rectifies light into electric current, in a collective quantum state with correlation driven electronic ferroelectricity. We show via explicit real-time dynamical calculations that the effect of the applied electric field on the electronic order parameter leads to a strong enhancement of the bulk photovoltaic effect relative to the values obtained in a conventional insulator. The enhancements include both resonant enhancements at sub-band-gap frequencies, arising from excitation of optically active collective modes, and broadband enhancements arising from nonresonant deformations of the electronic order. The deformable electronic order parameter produces an injection current contribution to the bulk photovoltaic effect that is entirely absent in a rigid-band approximation to a time-reversal symmetric material. Furthermore, our findings establish that correlation effects can lead to the bulk photovoltaic effect and demonstrate that the collective behavior of ordered states can yield large nonlinear optical responses.

14 SOLAR ENERGY↗
NASA NTRS2004

Deformations of Flat Unsymmetric Laminates Subjected to Inplane Loads

The geometrically nonlinear deformation response of initially flat unsymmetric cross-ply laminates subjected to an inplane compressive load and two sets of boundary conditions is studied. Stability of the deformations is considered. At issue is whether or not the plate remains flat with increased compressive loading, and whether it buckles. A semi-infinite unsymmetric cross-ply laminate is used to show the combined effects of geometric nonlinearities and bending-stretch coupling. Finite element results for finite laminates are then presented, and it is shown that to a large degree the boundary conditions control the character of the deformation response. It appears that clamped boundary conditions support buckling behavior, in the classic sense of bifurcation, whereas simply-supported conditions do not.

Hyer, Michael W.↗
DOE OSTI2022

Simulating the non-monotonic strain response of nanoporous multiferroic composites under electric field control

In this work, we simulate and analyze the mechanical response of a class of multiferroic materials consisting of a templated porous nanostructure made out of cobalt ferrite (CFO) partially filled by atomic layer deposition (ALD) with a ferroelectric phase of lead zirconate titanate (PZT). The strain in the device is measured when an electric field is applied for varying ALD thicknesses, displaying a non-monotonic dependence with a maximum strain achieved for a coating thickness of 3 nm. To understand this behavior, we apply finite element modeling to the smallest repeatable unit of the nanoporous template and simulate the mechanical response as a function of PZT coating thickness. We find that this non-monotonic response is caused by the interplay between two driving forces opposing one another. First, increased porosity works toward increasing the strain due to a reduced system stiffness. Second, decreased porosity involves a larger mass fraction of PZT, which drives the electro-mechanical response of the structure, thus leading to a larger strain. The balance between these two driving forces is controlled by the shear coupling at the CFO/PZT interface and the effective PZT cross section along the direction of the applied electric field. Here, our numerical results show that considering a nonlinear piezoelectric response for PZT leads to an improved agreement with the experimental data, consistent with ex situ poling of the nanostructure prior to magnetic measurements.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS2014

Hybrid Wing Body Model Identification Using Forced-Oscillation Water Tunnel Data

Static and dynamic testing of the NASA 0.7 percent scale Hybrid Wing Body (HWB) configuration was conducted in the Rolling Hills Research Corporation water tunnel to investigate aerodynamic behavior over a large range of angle-of-attack and to develop models that can predict aircraft response in nonlinear unsteady flight regimes. This paper reports primarily on the longitudinal axis results. Flow visualization tests were also performed. These tests provide additional static data and new dynamic data that complement tests conducted at NASA Langley 14- by 22-Foot Subsonic Tunnel. HWB was developed to support the NASA Environmentally Responsible Aviation Project goals of lower noise, emissions, and fuel burn. This study also supports the NASA Aviation Safety Program efforts to model and control advanced transport configurations in loss-of-control conditions.

Murphy, Patrick C.↗
NASA NTRS1993

An engineering model of woven composites based on micromechanics

Composites with three-dimensional woven architectures exhibit large strains to failure when compared to composites made up of the same materials but not with three-dimensional interlocking tows. The fracture mechanics of such three-dimensional architectures is a subject requiring substantial investigation and experimental testing. Classical fracture mechanics concepts (for instance, an isolated defect in a homogeneous body) will not be applicable to the woven fracture test specimen. The use of an isolated singularity to characterize an entire specimen is inadequate when the density of defects is considerable and the material is heterogeneous. Modelling of such a complex system requires a great deal of insight and consideration as well as prudent choices of model sizes to make numerical schemes feasible. The purpose of this manuscript is to review our recently acquired knowledge of damage accumulation in woven composites and to describe a practicable model of the macroscopic behavior in these and other complex composite architectures based on such knowledge. In this manuscript, discussion will be limited to uniaxial compressive loading; considerations of general loading (monotonic and cyclic) will appear in a subsequent manuscript. Our modelling efforts may be briefly described as follows: the composite is subdivided into microstructural elements (microelements) in which the micromechanical modelling is either understood rigorously or can be represented adequately by statistical parameters. There can be microstructural elements for many different types of composite components, such as the various types of warp and weft and matrix for three-dimensional woven composites. The physical dimensions of microelements are made as large as possible while the response within the element can still be represented by a single micromechatlical calculation. The various elements are linked together(sometimes by associating distinct corners and edges, sometimes by superposition) in a pattern which resembles a particular weave architecture. The model can then be loaded in any manner and the linear and nonlinear elastic responses of representative weaves can be calculated. After the elastic regime, the fracture response is determined by monitoring the damage accumulation.

Carter, W. C.↗
NASA NTRS1990

Unsteady blade-surface pressures on a large-scale advanced propeller: Prediction and data

An unsteady 3-D Euler analysis technique is employed to compute the flow field of an advanced propeller operating at an angle of attack. The predicted blade pressure waveforms are compared with wind tunnel data at two Mach numbers, 0.5 and 0.2. The inflow angle is three degrees. For an inflow Mach number of 0.5, the predicted pressure response is in fair agreement with data: the predicted phases of the waveforms are in close agreement with data while the magnitudes are underpredicted. At the low Mach number of 0.2 (takeoff), the numerical solution shows the formation of a leading edge vortex which is in qualitative agreement with measurements. However, the highly nonlinear pressure response measured on the blade suction surface is not captured in the present inviscid analysis.

Nallasamy, M.↗
DOE OSTI2021

Effect of Soil Properties and Input Motion on Site Amplification Using Validated Nonlinear Soil Model

Here, three-dimensional (3-D) nonlinear site response analyses are conducted using finite element models of actual soil profiles from ten nuclear power plant (NPP) sites in the United States to investigate the effects of soil properties and input motions on site amplification. The modeling approach developed in this study combines several novel elements, such as 3-D analysis (including vertical motions), nonlinear inelastic behavior of soil (strain-dependent shear modulus reduction and hysteretic damping), formulation of nonreflecting boundary conditions at the base, and generation of realistic outcrop ground motions for specific sites. All these elements of the modeling approach are first validated using actual data from five earthquakes at three downhole array stations recorded in the Kiban-Kyoshin network (KiK-net), Japan. The same approach is then used to develop site models of ten NPP sites in the United States and corresponding ground motions that are spectrally matched to the site hazard spectra. Eight sets of three-component input motions are used in the study and are categorized on the basis of presence or absence of a near-field pulse in the seed ground motions used for spectral matching. It is found that all sites retain a definite site amplification function regardless of the input motion, provided that the seed motion is spectrally matched to the site hazard spectra. The magnitude of site amplification and frequencies at which they occur depend upon soil properties, particularly the shear wave velocity profile and the constitutive relationship (strain-dependent shear modulus reduction and hysteretic damping) of soil. Amplification of spectral acceleration in the vertical direction (up-down motion) is found to be just as much as, if not more than, the amplification in the horizontal direction. Peak shear strain is found to be about 20% larger for near-field motions compared to far-field motions whereas maximum horizontal site amplification for far-field motions is found to be consistently larger than that of near-field motions, even though the differences between the two remain within the scatter resulting from individual ground motions.

99 GENERAL AND MISCELLANEOUS↗
NASA NTRS1990

Unsteady blade surface pressures on a large-scale advanced propeller - Prediction and data

An unsteady three dimensional Euler analysis technique is employed to compute the flowfield of an advanced propeller operating at an angle of attack. The predicted blade pressure waveforms are compared with wind tunnel data at two Mach numbers, 0.5 and 0.2. The inflow angle is three degrees. For an inflow Mach number of 0.5, the predicted pressure response is in fair agreement with data: the predicted phases of the waveforms are in close agreement with data while the magnitudes are underpredicted. At the low Mach number of 0.2 (take-off) the numerical solution shows the formation of a leading edge vortex which is in qualitative agreement with measurements. However, the highly nonlinear pressure response measured on the blade suction surface is not captured in the present inviscid analysis.

Nallasamy, M.↗
NASA NTRS1989

Accuracy of telemetry signal power loss in a filter as an estimate for telemetry degradation

When telemetry data is transmitted through a communication link, some degradation in telemetry performance occurs as a result of the imperfect frequency response of the channel. The term telemetry degradation as used here is the increase in received signal power required to offset this filtering. The usual approach to assessing this degradation is to assume that it is equal to the signal power loss in the filtering, which is easily calculated. However, this approach neglects the effects of the nonlinear phase response of the filter, the effect of any reduction of the receiving system noise due to the filter, and intersymbol interference. Here, an exact calculation of the telemetry degradation, which includes all of the above effects, is compared with the signal power loss calculation for RF filtering of NRZ data on a carrier. The signal power loss calculation is found to be a reasonable approximation when the filter follows the point at which the receiving system noise is introduced, especially if the signal power loss is less than 0.5 dB. The signal power loss approximation is less valid when the receiving system noise is not filtered.

Koerner, M. A.↗
DOE OSTI2021

Nonlinear dynamics of topological Dirac fermions in 2D spin-orbit coupled materials

Abstract The graphene family materials are two-dimensional staggered monolayers with a gapped energy band structure due to intrinsic spin-orbit coupling. The mass gaps in these materials can be manipulated on-demand via biasing with a static electric field, an off-resonance circularly polarized laser, or an exchange interaction field, allowing the monolayer to be driven through a multitude of topological phase transitions. We investigate the dynamics of spin-orbit coupled graphene family materials to unveil topological phase transition fingerprints embedded in the nonlinear regime and show how these signatures manifest in the nonlinear Kerr effect and in third-harmonic generation processes. We show that the resonant nonlinear spectral response of topological fermions can be traced to specific Dirac cones in these materials, enabling characterization of topological invariants in any phase by detecting the cross-polarized component of the electromagnetic field. By shedding light on the unique processes involved in harmonic generation via topological phenomena our findings open an encouraging path towards the development of novel nonlinear systems based on two-dimensional semiconductors of the graphene family.

36 MATERIALS SCIENCE↗
NASA NTRS1979

Optimal estimator model for human spatial orientation

A model is being developed to predict pilot dynamic spatial orientation in response to multisensory stimuli. Motion stimuli are first processed by dynamic models of the visual, vestibular, tactile, and proprioceptive sensors. Central nervous system function is then modeled as a steady-state Kalman filter which blends information from the various sensors to form an estimate of spatial orientation. Where necessary, this linear central estimator has been augmented with nonlinear elements to reflect more accurately some highly nonlinear human response characteristics. Computer implementation of the model has shown agreement with several important qualitative characteristics of human spatial orientation, and it is felt that with further modification and additional experimental data the model can be improved and extended. Possible means are described for extending the model to better represent the active pilot with varying skill and work load levels.

Borah, J.↗
NASA NTRS1986

Delamination growth in composite materials

The Double Cantilever Beam (DCB) and the End Notched Flexure (ENF) specimens are employed to characterize MODE I and MODE II interlaminar fracture resistance of graphite/epoxy (CYCOM 982) and graphite/PEEK (APC2) composites. Sizing of test specimen geometries to achieve crack growth in the linear elastic regime is presented. Data reduction schemes based upon beam theory are derived for the ENF specimen and include the effects of shear deformation and friction between crack surfaces on compliance, C, and strain energy release rate, G sub II. Finite element (FE) analyses of the ENF geometry including the contact problem with friction are presented to assess the accuracy of beam theory expressions for C and G sub II. Virtual crack closure techniques verify that the ENF specimen is a pure Mode II test. Beam theory expressions are shown to be conservative by 20 to 40 percent for typical unidirectional test specimen geometries. A FE parametric study investigating the influence of delamination length and depth, span, thickness and material properties on G sub II is presented. Mode I and II interlaminar fracture test results are presented. Important experimental parameters are isolated, such as precracking techniques, rate effects, and nonlinear load-deflection response. It is found that subcritical crack growth and inelastic materials behavior, responsible for the observed nonlinearities, are highly rate-dependent phenomena with high rates generally leading to linear elastic response.

Gillespie, J. W., Jr.↗
NASA NTRS2005

Simulating Vibrations in a Complex Loaded Structure

The Dynamic Response Computation (DIRECT) computer program simulates vibrations induced in a complex structure by applied dynamic loads. Developed to enable rapid analysis of launch- and landing- induced vibrations and stresses in a space shuttle, DIRECT also can be used to analyze dynamic responses of other structures - for example, the response of a building to an earthquake, or the response of an oil-drilling platform and attached tanks to large ocean waves. For a space-shuttle simulation, the required input to DIRECT includes mathematical models of the space shuttle and its payloads, and a set of forcing functions that simulates launch and landing loads. DIRECT can accommodate multiple levels of payload attachment and substructure as well as nonlinear dynamic responses of structural interfaces. DIRECT combines the shuttle and payload models into a single structural model, to which the forcing functions are then applied. The resulting equations of motion are reduced to an optimum set and decoupled into a unique format for simulating dynamics. During the simulation, maximum vibrations, loads, and stresses are monitored and recorded for subsequent analysis to identify structural deficiencies in the shuttle and/or payloads.

Cao, Tim T.↗
NASA NTRS1995

Nonlinear viscoelastic characterization of polymer materials using a dynamic-mechanical methodology

Polymer materials retrieved from LDEF exhibit nonlinear constitutive behavior; thus the authors present a method to characterize nonlinear viscoelastic behavior using measurements from dynamic (oscillatory) mechanical tests. Frequency-derived measurements are transformed into time-domain properties providing the capability to predict long term material performance without a lengthy experimentation program. Results are presented for thin-film high-performance polymer materials used in the fabrication of high-altitude scientific balloons. Predictions based upon a linear test and analysis approach are shown to deteriorate for moderate to high stress levels expected for extended applications. Tests verify that nonlinear viscoelastic response is induced by large stresses. Hence, an approach is developed in which the stress-dependent behavior is examined in a manner analogous to modeling temperature-dependent behavior with time-temperature correspondence and superposition principles. The development leads to time-stress correspondence and superposition of measurements obtained through dynamic mechanical tests. Predictions of material behavior using measurements based upon linear and nonlinear approaches are compared with experimental results obtained from traditional creep tests. Excellent agreement is shown for the nonlinear model.

Strganac, Thomas W.↗
NASA NTRS1987

Advances in computational structural and solid mechanics; Proceedings of the First World Congress on Computational Mechanics, University of Texas, Austin, Sept. 22-26, 1986

Papers are presented on the nonlinear dynamic analysis of quasi-symmetric anisotropic structures, the analysis of large deformations of membrane shells by the generalized finite difference method, the vibration of shear-deformable laminated plate structures by the finite strip method, and Coon's surface method for the formulation of finite elements for plates and shells. Other topics include an evaluation of higher-order modal methods for calculating the transient structural response, a nonlinear dynamic analysis of frame structures, and a nonlinear analysis of a truss by energy minimization. Also considered are an incremental Galerkin method for plates and stiffened plates, a comparison of the postbuckling behavior of plates and shells, and a general solution of bending in a cylindrical shell.

Noor, Ahmed K.↗
DOE OSTI2023

Time-varying gradient metasurface with applications in all-optical beam steering

Integrating the large, subpicosecond nonlinear optical response of epsilon-near-zero (ENZ) materials with the broad design freedoms of plasmonic metasurfaces shows potential for creating rapidly modulated optical devices with possible applications in telecommunications, sensing, and reactive beam steering. In this work, we experimentally investigate a metasurface consisting of a plasmonic gradient array on a thin layer of indium tin oxide (ITO), characterize how incident probe pulses diffract from a system as it is being dynamically modulated by a pump pulse at wavelengths near the ENZ region. Angular shifts in the diffraction orders are observed and can be principally attributed to the adiabatic wavelength conversion of the probe as it witnesses the temporal change of index induced by the pump. Of note, the asymmetric gradient metasurface, considered to be a blazed diffraction grating, shows significantly different dynamic responses for different diffraction orders. The free-space wavelength shift to +1 and -1 diffraction orders is 6 and 12 nm, resulting in steering angle changes of 0.65 and 1.5°, respectively.

42 ENGINEERING↗
DOE OSTI2020

Nonlinear time-domain spectroscopy near a band inversion

We develop a theory for the nonlinear time-domain response of a semimetal driven by an ultrafast optical pulse. At quadratic order in the driving field we find that the response near a band inversion transition contains a coherent oscillating component proportional to field intensity with a frequency that can be tuned over a wide range (from terahertz to the near IR) selected by the chemical potential. Finally, we illustrate the effect by calculating the induced current as a function of time for a two-band system with time-reversal symmetry but broken parity symmetry to study semimetals where large Berry curvature near a band inversion transition promotes this nonlinear response.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗