Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Environmental barrier coatings on enhanced roughness SiC: Effect of plasma spraying conditions on properties and performance

Environmental barrier coatings for SiC/SiC composites are limited by the melting temperature of the Si bond coating near 1414°C. Systems without a bond coating may be required for future turbine applications where material temperatures go beyond 1350 °C. Here, enhanced roughness SiC substrates were developed to assess coating adhesion without the bond coating. Two EBCs with different YbMS/YbDS ratios were produced via modified plasma spraying parameters. Coating microstructure, thermal expansion, and modulus were measured for comparison of coating properties. Cyclic steam exposures at 1350°C were performed to assess oxidation resistance. The EBC with increased concentration of Yb 2 SiO 5 secondary phase displayed a higher CTE, which is typically expected to decrease adhesion lifetimes due to an increase in stress upon thermal cycling. Yet, the EBC chemistry with increased Yb 2 SiO 5 concentration was able to experience longer cycling times prior to coating delamination, likely due to interface interactions with the substrate and the thermally grown oxide.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Reactive flash sintering and characterization of bulk high entropy nitrides

Over the past decade, numerous high-entropy ceramics have been synthesized, often displaying attractive properties. However, the study on facile preparation of bulk high entropy nitrides (HEN) are limited, despite its broad potential applications. This research demonstrates for the first time rapid fabrication (within ∼6 min) of bulk high-entropy nitrides, especially (Al 0.17 Nb 0.17 Ta 0.17 Ti 0.32 Zr 0.17 )N, from binary nitride powder mixtures using a highly efficient reactive flash sintering (RFS) technique. X-ray diffraction (XRD) shows the HENs from RFS are near single-phase solid solutions with a rock salt crystal structure, while in situ synchrotron study carried out during RFS captured in real time the formation of HEN, which was preserved upon cooling, suggesting thermodynamic stability of the HEN phase, even up to extreme pressure (∼35.6 GPa). Microscopic analyses using SEM, STEM, and EDS reveal decent uniformity for HEN with no obvious segregation of elements, even to submicron scale. Some properties of the obtained bulk HENs are consistent with expectations. For example, their hardness and bulk modulus are close to estimates based on rule-of-mixture (ROM) values from the constituent binary nitrides. Meanwhile, some other measured properties seem to show surprises. For example, the fracture toughness for the HENs (e.g., 7.81 ± 1.40 MPa•m 1/2 or higher) turns out to be more than double of the expected ROM estimates. The significantly improved fracture toughness is attributed to the observed nano-layered structure of the HENs, despite the HEN’s cubic crystal structure and high hardness. In addition, the oxidation resistance shows improvement up till ∼800°C, possibly due to Ta doping that suppress oxygen vacancy formation in the oxide shell, while the 5-metal HEN of (Al 0.17 Nb 0.17 Ta 0.17 Ti 0.32 Zr 0.17 )N displays superconductivity (T c of ∼5–7 K from magnetism and resistivity measurements, slightly lower than ROM estimate), despite insulating property of starting AlN. Furthermore, future study combining experimental investigation using larger samples to confirm the observed increase in fracture toughness and oxidation resistance, theoretical modeling at different length scale, and more detailed structural/chemical characterization, especially at the atomic scale, are all needed to fully understand the inter-relationships between composition, processing, structure, and novel properties for these HENs and the development of related new materials for different applications.

Flash sintering↗
DOE OSTI2023

Effect of printing parameters on 3D-printed carbon fiber-reinforced polymer composites under magnetic field control

Magnetic field controlled (MFC) 3D printing is a promising method for realizing the intelligent control of the structural performance of carbon fiber-reinforced plastic (CFRP) composites by adjusting the fiber orientation during the printing process. However, few studies have focused on the influence of the printing parameters on the magnetic control of the fiber direction. Therefore, in this study, the mechanical properties and internal fiber distributions of MFC 3D-printed samples of CFRP composites with 10 wt% fiber content, which were printed at different speeds and layer thicknesses, were investigated. Subsequently, the effects of the fiber content on the mechanical properties and fiber distribution of the MFC 3D-printed samples were studied. Furthermore, the origin of fiber fracture was evaluated through observation and analysis of the fracture section using scanning electron microscopy. The fiber orientation could be well adjusted under the action of a magnetic field and adjustment of printing parameters, thereby improving the tensile strength, young's modulus significantly with slightly decrease of fracture elongation. The recommended parameter combinations (printing speed and layer thickness) were 40 mm/s and 0.2 mm for 10 wt% fiber content CFRP composites.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Three-dimensional mapping of mineral in intact shark centra with energy dispersive x-ray diffraction

The centra of shark vertebrae consist of cartilage mineralized by a bioapatite similar to bone's carbonated hy-droxyapatite, and, without a repair mechanism analogous to remodeling in bone, these structures still survive millions of cycles of high-strain loading. The main structures of the centrum are an hourglass-shaped double cone and the intermedialia which supports the cones. Little is known about the nanostructure of shark centra, spe-cifically the relationship between bioapatite and cartilage fibers, and this study uses energy dispersive diffraction (EDD) with polychromatic synchrotron x-radiation to study the spatial organization of the mineral phase and its crystallographic texture. The unique energy-sensitive detector array at beamline 6-BM-B, the Advanced Photon Source, enables EDD to quantify the texture within each sampling volume with one exposure while constructing 3D maps via specimen translation across the sampling volume. Herein this study maps a centrum from two shark orders, a carcharhiniform and a lamniform, with different intermedialia structures. In the blue shark (Prionace glauca, Carcharhiniformes), the bioapatite's c-axes are oriented laterally within the centrum's cone walls but axially within the wide wedges of the intermedialia; the former is interpreted to resist lateral deformation, the latter to support axial loads. In the shortfin mako (Isurus oxyrinchus, Lamniformes), there is some tendency for c-axis variation with position, but the situation is unclear because one dimension of the sampling volume is consid-erably larger than the thickness and spacing of the intermedialia's radially-oriented lamellae. Because elastic modulus in collagen plus bioapatite mineralized tissues varies significantly with both volume fraction of bio-apatite and crystallographic texture, the present 3D EDD-derived maps should inform future 3D numerical models of shark centra under applied load.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Unconventional pressure-induced magnetic transitions and mechanical properties in non-magnetic LaFeSi

Here, this work demonstrates that two consecutive magnetic transitions occur in non-magnetic LaFeSi compound under negative hydrostatic pressure (small volume expansion). Electronic structure properties of LaFeSi were calculated using density functional theory (DFT) to understand the origin of these magnetic transitions. Mechanical properties of LaFeSi, especially elastic properties (shear and Young’s modulus, and Poisson’s ratio), were determined by DFT distortion calculations to elucidate lattice anisotropy and stability. The antiferromagnetic transition at –7.52 GPa, predicted in our work for LaFeSi, is consistent with the reported experimentally observed antiferromagnetic ground states in CeMnSi and LaMnSi compounds having similar crystal geometry. This finding of unexpected magnetic ordering predicts that layered non-magnetic materials, like LaFeSi, may become magnetically active with lattice expansion.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Quantitative assessment of particle dispersion in polymeric composites and its effect on mechanical properties

In this work, an automated image analysis tool is developed to establish quantitative correlations between the particle/cluster size distribution and the mechanical properties of particle reinforced polymer composites (PRPC).This automated image analysis tool is developed within python programming software to process and analyze the microstructural images of the polymerbased composite materials. The spent coffee bean powder (SCBP) reinforced poly-propylene carbonate (PPC) polymer composite with differing wt.% of the filler is selected for the analysis. Detailed statistical analysis of the microstructural images reveals that ‘clustering of clusters’ is also presented in addition to the most commonly reported ‘clustering of particles’, and the distribution of particle/clusters is bimodal. Based on these findings, an effective volume fraction for the filler material is proposed to mainly capture the agglomeration effect. With this effective volume fraction, the standard rule-of-mixture model correctly captures the experimentally measured tensile strength and modulus as a function of filler wt.%. Further, the applicability of this effective volume fraction for other theoretical models is also analyzed. The detailed statistical analysis of the microstructure and the proposed effective volume fraction helps to develop a deeper quantitative understanding of the PRPC than the conventional qualitative correlation of microstructural features with the properties and failure processes.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tailoring grain growth and solid solution strengthening of single-phase CrCoNi medium-entropy alloys by solute selection

In the present study, we selected solutes to be added to the CrCoNi medium-entropy alloy (MEA) based on the mismatch of self-diffusion activation energy (SDQ) between the alloying elements and constituent elements of the matrix, and then investigated their grain growth behavior and mechanical properties. Mo and Al were selected as the solutes for investigation primarily because they have higher and lower SDQ, respectively, than those of the matrix elements; a secondary factor was their higher and lower shear modulus. Their concentrations were fixed at 3 at.% each because previous work had shown these compositions to be single-phase solid solutions with the face-centered cubic structure. Three alloys were produced by arc melting, casting, homogenizing, cold rolling and annealing at various temperatures and times to produce samples with different grain sizes. They were (a) the base alloy CrCoNi, (b) the base alloy plus 3 at.% Mo, and (c) the base alloy plus 3 at.% Al. The activation energies for grain growth of the CrCoNi, CrCoNi-3Mo and CrCoNi-3Al MEAs were found to be ~251, ~368 and ~219 kJ/mol, respectively, consistent with the notion that elements with higher SDQ (in this study Mo) retard grain growth (likely by a solute-drag effect), whereas those with lower values (Al) accelerate grain growth. The room-temperature tensile properties show that Mo increases the yield strength by ~40% but Al addition has a smaller strengthening effect consistent with their relative shear moduli. The yield strength as a function of grain size for the three singlephase MEAs follows the classical Hall-Petch relationship with much higher slopes (> 600 MPa μm -0.5 ) than traditional solid solutions. Furthermore, this work shows that the grain growth kinetics and solid solution strengthening of the CrCoNi MEA can be tuned by selecting solute elements that have appropriate diffusion and physical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2022

In situ study on medium-range order evolution during the polyamorphous phase transition in a Pd-Ni-P nanostructured glass

Engineering multiscale structural hierarchies in glassy alloys enable a broad spectrum of potential applications. Metallic glasses were born in hierarchical structures from atomic-to-nanometer scales. However, the frozen-in structures in traditional metallic glasses prepared by rapid quenching techniques are challenging to tailor. Here, we show that a Pd 40 Ni 40 P 20 bulk nanostructured glass of polyamorphous interfacial structures was prepared by inert-gas condensation with a laser evaporation source, and its multiscale structures could be engineered. In-situ scattering experiment results reveal polyamorphous phase transitions occurred in the interfacial regions, which are accompanied by the evolution of medium-range order and the nanoscale heterogeneous structures during the condensation process of glassy nanoparticles under high pressure and the following heating process. Moreover, changes in the cluster connectivity resulting from repacking of the local ordering induced by pressure and temperature could be observed. The thermophysical and mechanical properties, including boson peaks, hardness, and elasticity modulus, could be changed as a function of heat-treatment parameters. In conclusion, our findings would shed light on the synthesis of bulk nanostructured glassy alloys with tailorable thermodynamic and dynamical behavior as well as mechanical properties based on the understanding of metastability for polyamorphous interfacial phases.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of grain size on iron-boride nanoglasses

Metallic nanoglasses are made of amorphous grains that are separated by lower-density amorphous boundaries, which have been proposed to enhance plasticity through the deflection of cracks and shear bands at interfaces. It has been difficult to experimentally control grain size and interfacial structure to understand their roles in plastic deformation. Here, we fabricate bulk nanoglasses via compaction and sintering of colloidally synthesized amorphous iron-boride nanoparticles. These nanoglasses have amorphous grains with diameters from 116nm to 576nm and were tested using nanoindentation and micropillar compressions. The nanoglass with a grain size of 576 nm shows the highest elastic modulus and hardness of 101 GPa and 7.4GPa, respectively. Transmission electron microscopy reveals that nanocrystals form within the nanoglasses during compaction. Higher nanocrystal density correlates with higher nanoparticle crystallization enthalpy, an increase in plasticity, and a decrease in yield strength. Plastic strain of 5.0%, yield strength of 3.8GPa, and ultimate compressive strength of 2.7–3.8GPa were achieved. Here we show that the compaction of colloidal metallic glass nanoparticles results in robust bulk samples, with mechanical properties similar to that of other iron-based bulk metallic glasses.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High-pressure deformation of metallic glass nanoparticles

Here, the atomistic structure of metallic glasses is closely related to properties such as strength and ductility. Here, Ni 1-x B x metallic glass nanoparticles of two different sizes are compressed under quasi-hydrostatic high-pressure conditions in order to understand structural changes under stress. The structural changes in the nanoparticles were tracked using in situ high-pressure X-ray diffraction (XRD). The ambient pressure pair distribution functions generated from XRD showed that the smaller sized nanoparticles had a more compact amorphous structure with lower coordination number. XRD showed that the amorphous structure was stable up to the maximum pressures achieved. The bulk modulus of the smaller and larger sized nanoparticles was found to be 208 GPa and 178 GPa, respectively. This size-dependent high-pressure behavior was related to compositional differences between the nanoparticles. These results show that Ni 1-x B x metallic glass nanoparticles are highly stable under pressure, which could enable their use as inclusions in metal or ceramic matrix composites.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Non-linear elastic-plastic behavior of the invert glass lithium phosphorous oxynitride (LiPON)

Micro and nano-scale mechanical behavior of network/ionic glasses is dictated by their composition and the number of constraints per structural unit. From this perspective, the glass LiPON presents the opportunity for enhancement of the microscale ductility due to its rather unconstrained orthophosphate structure. Here, we use instrumented nanoindentation with different tip geometries to investigate the mechanical response of LiPON glass. The results reveal that the elastic modulus of LiPON is not constant and depends on pressure. With the method utilizing spherical nanoindentation and continuous stiffness measurement (CSM) we determine the yield point of LiPON. We propose the Drucker-Prager type of yield criterion for LiPON and estimate its yield stress in compression as 2.4 GPa. There exists another stress threshold, however, around 490 MPa, at which the elastic deformation becomes non-linear, and this can be mistaken for the yield stress.

Constitutive model↗
DOE OSTI2020

Low-temperature proton irradiation damage of isotropic nuclear grade IG-430 graphite

IG-430, a fine-grained, isotropic graphite grade is a promising candidate for the future Very High Temperature Reactors (VHTR). IG-430 which provides higher density, strength, and thermal conductivity, has already been developed as a graphite for next-generation HTGR, and is expected to be employed. This graphite grade, however, is lacking enough database that is needed for design. The present study aims to enhance the database with experimental data focusing on the low temperature regime (90–210 °C) by using 120–200 MeV protons to irradiate the IG-430 graphite to peak fluence of ~1.2 10 25 m –2 . It is anticipated that radiation-induced changes in the graphite properties and damage to be more pronounced in this low temperature regime than in elevated temperatures where damage annealing is taking place simultaneously. IG-430 graphite was characterized following irradiation for mechanical property changes (modulus and strength), dimensional stability and irradiation-induced growth as well as microstructural changes using high energy X-rays and different X-ray diffraction techniques. In assessing proton irradiation effects on the IG-430 graphite grade, comparison of radiation effects was made with the IG-43 grade, the un-purified version of IG-430, as well as other isotropic graphite grades. IG-430 was shown in this study to be better graphitized than other isotropic graphite grades. The study also revealed that during proton irradiation at low temperatures (~100 °C) the IG-430 exhibits stored energy release.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Acoustic mapping by picosecond ultrasonics for elastic property measurement: Experimental demonstration on a TRISO fuel compact

Picosecond ultrasonics has been demonstrated on a tristructural isotropic (TRISO) fuel compact to measure the elastic properties of each compact layer. This technique utilizes an ultrashort pump laser pulse to excite vibrations in a gold transducer film covering the surface of each component and a second probe laser pulse to record the resulting acoustic strain induced change in optical reflectance. From the damping of this film vibration, the acoustic reflection coefficient, which couples the elastic properties of the transducer film and the sample, can be obtained, enabling a calculation of the sample’s acoustic velocity and elastic modulus. Overall, results obtained from this method are consistent with known values of elastic moduli, namely that the SiC coating is the stiffest component of the compact while the carbonaceous matrix is the most compliant. Nanoindentation was conducted as a benchmark technique on the same sample and shows satisfactory agreement with the results of picosecond ultrasonics. Compared to other methods like nanoindentation, picosecond ultrasonics is multimodal with a capability of measuring several key properties simultaneously and has potentials to be coupled into optical fibers for remote sensing. Thus, these demonstration measurements reveal the methodology to be a promising candidate for in-situ and high-throughput optical characterizations of nuclear materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Failure evaluation of neutron-irradiated SiC/SiC composites by underwater acoustic emission

Here, understanding the statistical properties of mechanical properties of non-irradiated and neutron-irradiated SiC/SiC composites is essential for component design. This study aims to evaluate the detailed damage accumulation behavior of composites focusing on two fracture parameters: proportional limit stress (PLS) and acoustic emission (AE) onset stress. The developmental underwater AE technique, which is benefit in non-contact in-situ failure monitoring method during mechanical testing and in handle of the irradiated material, was first applied to evaluate damage accumulation behavior. Two types of chemical vapor infiltration SiC/SiC composites were used: one reinforced with Hi-Nicalon Type-S SiC fiber and one reinforced with Tyranno-SA3 SiC fiber in the form of satin-woven 2D fabrics with pyrolytic carbon interface. Neutron irradiation in the High Flux Isotope Reactor at Oak Ridge National Laboratory reached a fluence of 30 dpa at a temperature of 620–670°C. Four-point flexural tests were conducted to evaluate post-irradiation strength. Weibull statistics did not suggest marked degradation of composite strength. Detailed failure behavior evaluated by AE demonstrated no irradiation-induced change of the AE onset stress (i.e., crack initiation equivalent stress). Failure probability analysis suggests that increasing the reliability of composites (i.e., the Weibull modulus rather than strength itself) is essential to expanding the design margin and benefiting from a probabilistic design approach.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Finite temperature properties of uranium mononitride

Uranium mononitride (UN) is a promising nuclear fuel that combines the advantageous properties of readily used UO 2 and uranium alloys, such as high melting temperature and high uranium density, and thermal conductivity, respectively. A better understanding of UN behavior at operating temperatures can be obtained from finite temperature data, such as elastic properties. To get this information, ab initio molecular dynamics (AIMD) simulations were performed at five different temperatures using constant volume (NVT) and constant pressure (NPT) ensembles. Initially, the performance of PBE functional in reproducing experimental crystallographic properties and magnetic ordering is assessed. The finite temperature phonon dispersions are calculated using NVT simulation results, which show a softening of the phonon modes with increasing temperature. The NPT results are used to obtain the thermal expansion of UN and finite temperature electronic properties. The calculated thermal expansion is compared with our measurements using neutron diffraction. Additionally, the temperature dependent elastic properties of UN are evaluated using the strain-stress method in AIMD simulations, indicating that UN becomes softer and more compressible with increasing temperature. Also, the calculated Young’s modulus slope is in very good agreement with the experiment. The finite temperature heat capacity and electronic thermal conductivity are calculated from AIMD simulations, which are in better agreement with the experiment than the heat capacity and thermal conductivity calculated using the structures relaxed at 0K. Finally, the thermal diffusivity from AIMD has opposite temperature dependence compared to experimental results, which we argued comes from the underestimated electronic thermal conductivity.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

High temperature annealing of irradiated nuclear grade graphite

Previous work has shown that the material properties of nuclear grade graphite are substantially affected by the atomic and microstructural changes that occur during neutron-irradiation. The parameters that play a role in these changes are irradiation dose, temperature, graphite composition and the initial microstructure of the graphite. Understanding the details of how these material changes occur and exactly what the changes consists of will enable the prediction of the material property changes as a function of these variables. Other work has shown these atomic level and microstructural changes can be healed or annealed out by raising the irradiated graphite above its irradiation temperature. Here in this work, experiments were carried out to investigate how the properties of irradiated graphite recover when heated. By showing property recovery as a function of annealing temperature or energy, insight is provided into the type of damage that occurred during neutron-irradiation. The data presented here shows recovery of thermal diffusivity, coefficient of thermal expansion, Young's modulus and electrical resistivity between annealing temperatures of 500 °C and 2380 °C. Graphite grades NBG-18, IG-110 and PCEA are considered that were both stressed and unstressed during irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Equibiaxial flexural strength determination of UO 2 using a ball-on-ring test

To increase nuclear fuel performance and reliability, their mechanical properties require an accurate and statistically relevant assessment. Biaxial flexural strength tests provide an alternative to bend bar techniques for assessing mechanical behavior; namely, the transverse rupture strength (TRS) of ceramic samples. Biaxial test samples require simple geometries and minimal surface preparation, reducing fabrication costs and handling hazards. This study investigated the TRS of polycrystalline UO 2 fuel forms at room temperature using a ball-on-ring test fixture. Here, pellets were fabricated from UO 2 powder using conventional powder processing and sintering techniques. The TRS and Weibull parameters were obtained through Weibull statistics on over 60 UO 2 samples tested under equibiaxial flexure. The larger sample size in this study enabled a more robust Weibull statistical analysis than alternative test methods, which may not capture the stochastic failure of typical ceramics. Furthermore, two different loading ball diameters were employed to assess the impact of contact damage on fracture strength. While Hertzian contact damage was observed with the smaller loading ball, the fracture strength remained unaffected. A fracture analysis of the tested UO 2 samples indicated a mixture of intergranular and transgranular fracture that transitions to transgranular fracture with increasing distance from the fracture origin. The characteristic strength of the combined data sets was determined to be 148 MPa, and the Weibull modulus was determined to be 9.1. The TRS values and Weibull parameters were close to values found in the literature for alternative testing techniques using samples with similar microstructure and density. The findings in this study validate the ball-on-ring method used to obtain the TRS of UO 2 with a sample geometry more representative of nuclear fuels. Additionally, experimental TRS results from this study can be implemented in modeling codes to predict fuel performance, which is critical to fuel burnup extension and advanced nuclear fuel technologies.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗