Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “module degradation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

3D Frequency Domain Reflectometry Digital Twin of an Electrical Cable: A First Glance

Electrical cables within nuclear power plants (NPPs) are critical components required for power, control, and instrumentation systems which may be exposed to stressors, such as elevated temperatures and gamma radiation. Such stressors can lead to a reduction in the remaining useful life of electrical cables, jeopardizing the safety of NPP systems. To evaluate the effect of stressors on the degradation of electrical cables, electrical reflectometry methods are commonly employed. Frequency domain reflectometry (FDR) is a non-destructive electrical reflectometry method that uses transmission line theory to detect degradation or impedance changes within electrical cables. However, in most cases FDR is only applied to de-energized cables, limiting the application in NPPs as the cable system must be taken offline. In this work, we explore the development of an FDR digital twin to predict the degradation of an electrical cable exposed to elevated temperature, which is expected to reduce the need for offline FDR. A 3-conductor low-voltage electrical cable was selected for evaluation of the digital twin. The fully three-dimensional digital twin was developed in COMSOL using the RF module. A cable length of 30-m and frequency bandwidth of 400 MHz was selected to mimic real-world application of FDR. Over a 1-m region, the permittivity of the insulation was varied by up to 20% to model thermal degradation. The results demonstrate accurate detection of the insulation damage region, supporting further investigation of the FDR digital twin using real-world data and machine learning for predictive damage estimation or remaining lifetime.

Spencer, Mychal P.↗
NASA NTRS1989

On-orbit results of the LIPS 3/InP homojunction solar cell experiment

The flight performance of NASA Lewis Research Center's indium phosphide homojunction solar cell module on the LIPS 3 satellite is presented. A module of four n+p cells was fabricated and has been on-orbit on the LIPS 3 spacecraft since 1987. The experimental objective is the measurement of InP cell performance in the natural radiation environment of the 1100 kilometer altitude, 60 deg inclination, circular orbit. Flight data from the first year is near expected values, with no degradation in short-circuit current. The temperature dependence of current-voltage parameters is included along with the laboratory radiation tolerance studies necessary for normalization and analysis of the data. Details of the cell structure and flight module design are also discussed.

Brinker, David J.↗
DOE OSTI2020

Round-robin weathering test of various polymeric back-sheets for PV modules with different ultraviolet irradiation and sample temperatures

Durability assessment of materials exposed to natural weathering with expected service lifetimes of more than 20 years requires accelerated testing of the UV stability, especially for polymeric materials. Fraunhofer ISE organized an interlaboratory comparison for testing different back-sheets in various test laboratories using different UV sources. The five participating test laboratories used three different types of UV sources. The interaction of the UV radiation with the polymers used in PV modules is main subject of this round-robin. Laminates were produced by using solar glass and a suitable EVA encapsulant combined with 10 different back-sheets. The simultaneous usage of different optical filters allowed to investigate roughly the spectral sensitivity and the intensity impact. The degradation was followed by spectral reflectance and transmittance measurements and calculation of the yellowness index as degradation indicator. Clear differences in the degradation behavior of the different products were found.

14 SOLAR ENERGY↗
NASA NTRS1972

The effect of timing errors in optical digital systems.

The use of digital transmission with narrow light pulses appears attractive for data communications, but carries with it a stringent requirement on system bit timing. The effects of imperfect timing in direct-detection (noncoherent) optical binary systems are investigated using both pulse-position modulation and on-off keying for bit transmission. Particular emphasis is placed on specification of timing accuracy and an examination of system degradation when this accuracy is not attained. Bit error probabilities are shown as a function of timing errors from which average error probabilities can be computed for specific synchronization methods. Of significance is the presence of a residual or irreducible error probability in both systems, due entirely to the timing system, which cannot be overcome by the data channel.

Gagliardi, R. M.↗
NASA NTRS1978

Ion drive technology readiness for the 1985 Halley Comet rendezvous mission

This paper summarizes the results of an assessment performed by the Jet Propulsion Laboratory (JPL) in FY 77 of the technology readiness of ion propulsion technology to support a 1985 Halley Comet Rendezvous (HCR) mission. The assessment identifies the status of ion propulsion technology and risk of its utilization to perform the HCR mission as of July 1977 and provides projections of status and risk at the required date for an HCR project start, October 1978. These projections are based on the assumed completion of the development activities ongoing at the time of this assessment and the recommended new activities identified in this paper. The conclusions of the study indicate that a National Aeronautics and Space Administration (NASA) commitment to the performance-demanding HCR mission would involve significant risk, greater than that experienced in any post-1964 planetary mission, despite years of supporting research and advanced development funding for ion propulsion and even assuming the success of an ambitious, aggressive FY 78 pre-project advanced systems technology (AST) program proposed by JPL. Contributing principally to the identified risk are a marginal mass margin of 6.7%, driven by uncertainties in ion drive vehicle masses and an unconfirmed solar array power degradation model of 12%, and technology currently undemonstrated to meet HCR mission requirements in two of the six subsystems of the ion propulsion module: the thrust and solar array subsystems.

John L West↗
NASA NTRS1982

Radiation damage in front and back illuminated high resistivity silicon solar cells

Radiation induced degradation, in front and back illuminated 84 and 1250 ohm-cm n+pp+ silicon solar cells, was determined and cell performance interpreted using calculated optically injected charge distributions and cell voltage components. The 84 ohm-cm cell degraded less when illuminated from the front or n+ side compared to that when illuminated from the back or p+ side. On the other hand, the 1250 ohm-cm cell degraded less when back illuminated. It is concluded that, in addition to the usual mechanisms leading to decreased collection efficiencies, loss of conductivity modulation is a major cause of radiation damage in high resistivity silicon solar cells. These results suggest that radiation damage to high resistivity n+pp+ cells can be decreased by increasing cell collection efficiency and illuminating the cells from the p+ side.

Weinberg, I.↗
NASA NTRS1988

The behavior of a Costas loop in the presence of space telemetry signals

The telemetry modulation index, telemetry bit rate, subcarrier waveform, and subcarrier frequency are shown to be the key system parameters that contribute to the performance degradation of a Costas loop in the presence of space telemetry signals. The effects of the Doppler in the loop are also investigated. The results of this study were input to the Consultative Committee for Space Data Systems (CCSDS) for consideration in the future standard suppressed-carrier space telemetry system.

Nguyen, T. M.↗
NASA NTRS1990

Soft-decision Viterbi decoding with diversity combining

Diversity combining methods for convolutional coded and soft-decision Viterbi decoded channels in mobile satellite communications systems are evaluated and it is clarified that the pre-Viterbi-decoding maximal ratio combining shows better performance than other methods in Rician fading channels by computer simulation. A novel practical technique for maximal ratio combining is proposed, in which the coefficients for weighting are derived from soft-decision demodulated signals only. The proposed diversity combining method with soft-decision Viterbi decoding requires simple hardware and shows satisfactory performance with slight degradation of 0.3 dB in Rician fading channels compared with an ideal weighting scheme. Furthermore, this diversity method is applied to trellis coded modulation and significant Pe performance improvement is achieved.

Sakai, T.↗
NASA NTRS1992

The behavior of a Costas loop in the presence of space telemetry signals

When the Costas loop is operated in the presence of a residual carrier space telemetry signal, the loop reconstructs its carrier reference from an input signal whose carrier component is not completely suppressed. The telemetry signal investigated in this work is generated by phase shift-keying the data onto a subcarrier and then phase modulating onto the sinusoidal carrier. The telemetry modulation index, telemetry bit rate, subcarrier waveform, and subcarrier frequency are shown to be the key system parameters that contribute to the performance degradation of a Costas loop. Furthermore, the effect of Doppler shift on the loop is also investigated in this work.

Nguyen, Tien M.↗
NASA NTRS1992

Error analysis of optical correlators

With the growing interest in using binary phase only filters (BPOF) in optical correlators that are implemented on magnetooptic spatial light modulators, an understanding of the effect of errors in system alignment and optical components is critical in obtaining optimal system performance. We present simulations of optical correlator performance degradation in the presence of eight errors. We break these eight errors into three groups: 1) alignment errors, 2) errors due to a combination of component imperfections and alignment errors, and 3) errors which result solely from non-ideal components. Under the first group, we simulate errors in the distance from the object to the first principle plane of the transform lens, the distance from the second principle plane of the transform lens to the filter plane, and rotational misalignment of the input mask with the filter mask. Next we consider errors which result from a combination of alignment and component imperfections. These include errors in the transform lens, the phase compensation lens, and the inverse Fourier transform lens. Lastly we have the component errors resulting from the choice of spatial light modulator. These include contrast error and phase errors caused by the non-uniform flatness of the masks. The effects of each individual error are discussed, and the result of combining all eight errors under assumptions of reasonable tolerances and system parameters is also presented. Conclusions are drawn as to which tolerances are most critical for optimal system performance.

Ma, Paul W.↗
DOE OSTI2021

Achieving 5,000-h and 8,000-h Low-PGM Electrode Durability on Automotive Drive Cycles

Whereas total Pt loading in anode and cathode catalysts below 0.125 mg cm −2 is required to meet the stringent cost target for automotive fuel cell systems (FCS) for light duty vehicles, low-loaded cathode catalysts are susceptible to unacceptable aging-related performance losses at high current densities. A framework model, validated by accelerated stress test data, has identified cell voltage, relative humidity (RH) and temperature as the key operating variables that affect degradation of a high-activity d-PtCo/C cathode catalyst with 0.1 mg cm −2 Pt loading. Drive cycle simulations indicate that these can be controlled by properly selecting the minimum FCS power, compressor-expander module (CEM) turndown, and stack coolant temperature. The optimum system parameters are 4-kW e minimum power for an 80-kW e FCS, CEM turndown of 12.5, and 66 °C average coolant exit temperature that combine to limit the maximum cell voltage to 850 mV and outlet RH to 90%–100%. Depending on Pt loading, the mismatch between actual and allowable degradation for 10% power loss over 5,000-h lifetime requires the stack to be oversized by 2.4%–5%, resulting in 8.4%–41% lower Pt utilization and 7.1%–20.5% penalty in stack cost. The corresponding results for 8,000-h lifetime are 10.3%-14% stack oversizing, 23%–51.8% lower Pt utilization, and 24.1%–35.4% stack cost penalty.

08 HYDROGEN↗
DOE OSTI2025

C60-Based Ionic Salt Electron Shuttle for High-Performance Inverted Perovskite Solar Modules

Although C60 is usually the electron transport layer (ETL) in inverted perovskite solar cells, its molecular nature of C60 leads to weak interfaces that lead to non-ideal interfacial electronic and mechanical degradation. Here, we synthesized an ionic salt from C60, 4-(1',5'-dihydro-1'-methyl-2'H-[5,6] fullereno-C60-Ih-[1,9-c]pyrrol-2'-yl) phenylmethanaminium chloride (CPMAC), and used it as the electron shuttle in inverted PSCs. The CH2-NH3+ head group in the CPMA cation improved the ETL interface and the ionic nature enhanced the packing, leading to ~3-fold increase in the interfacial toughness compared to C60. Using CPMAC, we obtained ~26% power conversion efficiencies (PCEs) with ~2% degradation after 2,100 hours of 1-sun operation at 65degrees C. For minimodules (four subcells, 6 centimeters square), we achieved the PCE of ~23% with <9% degradation after 2,200 hours of operation at 55degrees C.

14 SOLAR ENERGY↗
DOE OSTI2021

NPRL2 reduces the niraparib sensitivity of castration-resistant prostate cancer via interacting with UBE2M and enhancing neddylation

In this study, we explored the regulatory effects of nitrogen permease regulator 2-like (NPRL2) on niraparib sensitivity, a PARP inhibitor (PARPi) in castrate-resistant prostate cancer (CRPC). Data from The Cancer Genome Atlas (TCGA) and Genotype-Tissue Expression (GTEx) program were retrospectively examined. Gene-set enrichment analysis (GSEA) was conducted between high and low NRPL2 expression prostate adenocarcinoma (PRAD) cases in TCGA. CCK-8 assay, Western blot analysis of apoptotic proteins, and flow cytometric analysis of apoptosis were applied to test niraparib sensitivity. Immunofluorescent (IF) staining and co-immunoprecipitation (co-IP) were conducted to explore the proteins interacting with NPRL2. Results showed that the upregulation of a canonical protein-coding transcript of NPRL2 (ENST00000232501.7) is associated with an unfavorable prognosis. Bioinformatic analysis predicts a physical interaction between NPRL2 and UBE2M, which is validated by a following Co-IP assay. This interaction increases NPRL2 stability by reducing polyubiquitination and proteasomal degradation. Depletion of NPRL2 or UBE2M significantly increases the niraparib sensitivity of CRPC cells and enhances niraparib-induced tumor growth inhibition in vivo. NPRL2 cooperatively enhances UBE2M-mediated neddylation and facilitates the degradation of multiple substrates of Cullin-RING E3 ubiquitin ligases (CRLs). In conclusion, this study identified a novel NPRL2-UBE2M complex in modulating neddylation and niraparib sensitivity of CRPC cells. Therefore, targeting NPRL2 might be considered as an adjuvant strategy for PARPi therapy.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2025

Weakly Solvating Electrolyte to Enable Lithium- and Manganese-Rich Cathode-Based Li-Ion Batteries

Traditional ethylene carbonate (EC)-based electrolytes exhibit strong solvation power at the surface of the layered transition metal oxide cathodes, which accelerates transition metal dissolution. The subsequent migration and deposition of dissolved transition metal species on the anode surface lead to significant capacity fading. To overcome this difficulty, we report a weakly solvating, all-fluorinated electrolyte designed to mitigate transition metal dissolution. For the first time, the role of electrolyte solvation in suppressing transition metal dissolution is systematically investigated. The tailored electrolyte significantly reduces transition metal dissolution and enhances the electrochemical performance of Li- and Mn-rich (LMR) cathode/graphite cells. This solvation-modulating strategy offers a broadly applicable framework for stabilizing interphases in other earth-abundant cathode chemistries, which similarly demand kinetic protection against interfacial degradation.

25 ENERGY STORAGE↗
DOE OSTI2025

Fiber-optic bolometers with high-temperature tolerance and reduced time constants for fusion plasma diagnostics

Fiber-optic bolometers (FOBs) designed for plasma radiation measurement in magnetically confined fusion environments have been previously developed and tested at the DIII-D tokamak. These FOBs utilize a silicon Fabry–Perot interferometer at the fiber tip for temperature measurement and a gold disk as a radiation absorber. This paper presents recent advancements in the development of FOBs with reduced cooling time constants and enhanced temperature tolerance. We also demonstrate high-temperature operation and report findings from irradiation tests. By incorporating a copper sensor holder as a thermal sink and integrating two closely packed sensor heads into a compact design, the cooling time constants were reduced to ∼100 ms in vacuum, while minimizing uncertainties caused by temperature gradients. The FOBs were subjected to heating at 400 °C for five hours, with no observed degradation in noise performance post-heating. High-temperature operation tests were conducted at ∼220 °C using a 404 nm square-wave modulated laser to simulate the plasma radiation. In addition, four FOBs constructed from copper-coated pure-silica fibers were fabricated and underwent irradiation testing, enduring a total γ-radiation dose of 15.2 MGy and a neutron fluence of 1.6 × 10 18 n/cm 2 . As a result, the FOBs maintained their physical integrity and the optical signal shows high visibility throughout the test.

42 ENGINEERING↗
DOE OSTI2022

Advanced Thin Film Core Technology: CIGS Final Technical Report (FTR)

Cu(In,Ga)Se 2 (CIGS) thin-film photovoltaics are a high-efficiency and reliable technology. This project completed research in two important areas and was designed to work collaboratively with industrial partners. Task 1: Alkali Science focused on alkali post-deposition treatments (PDT). PDTs have been instrumental in the dramatic voltage improvements that have moved CIGS device efficiencies from 20% to 23.35% [1]. Based on a survey of CIGS companies at the beginning of the project, the single biggest breakthrough for the CIGS community would be a mechanistic understanding of the role of alkalis in the material system. Significant accomplishments of Task 1: Alkali Science: 1) KF post-deposition treatments were shown to improve lifetime, open-circuit voltage (VOC), and efficiency of industrial partner samples, even when done as a later step, separate from the original CIGS deposition. 2) KF boosted efficiency when incorporated at the end of the third stage of NREL CIGS growth. 3) XPS characterization of CIGS surfaces with and without PDTs led to a proposed mechanism whereby K drives structural transformation at 350 degrees C that is locked in at room temperature even after K is rinsed away. 4) Published recipes for KF and RbF PDTs. Literature to date did not provide enough detail to quickly reproduce experimental results. 5) Identified most important parameters (RbF cell temperature and lamp setpoint temperature) and set boundaries for successful RbF PDTs. The purpose of Task 2: Cell-level Reliability was to overcome the largest challenges to investor confidence and long product lifetime in CIGS-based photovoltaic products: metastability, shading-induced hot spots, and potential-induced degradation (PID). Key findings were made in each of these areas by studying CIGS reliability at the cell level: 1) Published NREL's cell-level reliability testing procedures along with challenges that were encountered while developing them. These were also distributed to the community through an MRS conference presentation. 2) Decreased metastability by adding a CdS hole-injection layer between the CIGS and Zn(O,S) in the device stack. It also improved device performance. Materials other than CdS can be used for the same purpose. 3) Reduced front-glass PID by replacing soda-lime glass with low-Na borosilicate glass. 4) Found that PID depends on leakage current and light/electrical bias. This will help labs avoid test-specific degradation. 5) Discovered that CIGS can suffer from two different types of PID with different mechanisms. Front is slower and leads to shunting ZnO. Back is faster and degrades the p-n junction. 6) Holding cells at open circuit slows PID compared to short circuit. This affects testing protocols for glass/glass modules.

14 SOLAR ENERGY↗
NASA NTRS1988

Application of copper-carbon fiber composites to power semiconductor devices

Copper-carbon composite electrodes are used in a series of power semiconductor devices, i.e., resin molded diodes, button-type diodes, stud-type diodes, power modules, and integrated circuit igniter modules. The properties of these power semiconductor devices compare favorably with those conventional devices using Mo or W electrodes. In thermal fatigue tests, no degradation in the electrical and mechanical characteristics of these devices are observed. The new composite electrode with carbon fibers satisfies all of the major requirements for the electrodes in power semiconductor devices.

Kuniya, Keiichi↗
NASA NTRS2007

Lightweight, Flexible Solar Cells on Stainless Steel Foil and Polymer for Space and Stratospheric Applications

The availability of low-cost, lightweight and reliable photovoltaic (PV) modules is an important component in reducing the cost of satellites and spacecraft. In addition, future high-power spacecraft will require lightweight PV arrays with reduced stowage volume. In terms of the requirements for low mass, reduced stowage volume, and the harsh space environment, thin film amorphous silicon (a-Si) alloy cells have several advantages over other material technologies (1). The deposition process is relatively simple, inexpensive, and applicable to large area, lightweight, flexible substrates. The temperature coefficient has been found to be between -0.2 and -0.3 %/degC for high-efficiency triple-junction a-Si alloy cells, which is superior for high temperature operation compared to crystalline Si and triple-junction GaAs/InGaP/Ge devices at 0.53 %/degC and 0.45 %/degC, respectively (2). As a result, the reduction in efficiency at high temperature typical in space conditions is less for a-Si alloy cells than for their crystalline counterparts. Additionally, the a-Si alloy cells are relatively insensitive to electron and proton bombardment. We have shown that defects that are created by electrons with energies between 0.2 to 2 MeV with fluence up to 1x10(exp 15) e/sq cm and by protons with energy in the range 0.3 MeV to 5 MeV with fluence up to 1x10(exp 13) p/sq cm can be annealed out at 70 C in less than 50 hours (1). Further, modules incorporating United Solar s a-Si alloy cells have been tested on the MIR space station for 19 months with only minimal degradation (3). For stratospheric applications, such as the high altitude airship, the required PV arrays are typically of considerably higher power than current space arrays. Airships typically have a large area available for the PV, but weight is of critical importance. As a result, low cost and high specific power (W/kg) are key factors for airship PV arrays. Again, thin-film a-Si alloy solar cell technology is well suited to such applications.

Beernink, Kevin↗