Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructured surfaces”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Thermal degradation study of silicon carbide threads developed for advanced flexible thermal protection systems

Silicon carbide (SiC) fiber is a material that may be used in advanced thermal protection systems (TPS) for future aerospace vehicles. SiC fiber's mechanical properties depend greatly on the presence or absence of sizing and its microstructure. In this research, silicon dioxide is found to be present on the surface of the fiber. Electron Spectroscopy for Chemical Analysis (ESCA) and Scanning Electron Microscopy (SEM) show that a thin oxide layer (SiO2) exists on the as-received fibers, and the oxide thickness increases when the fibers are exposed to high temperature. ESCA also reveals no evidence of Si-C bonding on the fiber surface on both as-received and heat treated fibers. The silicon oxide layer is thought to signal the decomposition of SiC bonds and may be partially responsible for the degradation in the breaking strength observed at temperatures above 400 C. The variation in electrical resistivity of the fibers with increasing temperature indicates a transition to a higher band gap material at 350 to 600 C. This is consistent with a decomposition of SiC involving silicon oxide formation.

Tran, Huy Kim↗

Room temperature degradation of YBa2Cu3O(7-x) superconductors in varying relative humidity environments

An aging study was performed to determine the stability of YBa2Cu3O(7-x) ceramics in humid environments at 20 C. In this study, fired ceramic specimens were exposed to humidity levels ranging from 30.5 to 100 percent for 2-, 4-, and 6-week time intervals. After storage under these conditions, the specimens were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and electrical resistance measurements. At every storage condition evaluated, the fired ceramics were found to interact with H2O present in the surrounding environment, resulting in the decomposition of the YBa2Cu3O(7-x) phase. XRD data showed that BaCO3, CuO, and Y2BaCuO5 were present after aging and that the peak intensities of these impurity phases increased both with increasing humidity level and with increasing time of exposure. Additionally, SEM analyses of the ceramic microstructures after aging revealed the development of needle-like crystallites along the surface of the test specimens after aging. Furthermore, the superconducting transition temperature T(sub c) was found to decrease both with increasing humidity level and with increasing time of exposure. All the specimens aged at 30.5, 66, and 81 percent relative humidity exhibited superconducting transitions above 80 K, although these values were reduced by the exposure to the test conditions. Conversely, the specimens stored in direct contact with water (100 percent relative humidity) exhibited no superconducting transitions.

Hooker, M. W.↗

Impact of Powder Variability on the Microstructure and Mechanical Behavior of Selective Laser Melted (SLM) Alloy 718

Nickel Alloy 718 has found wide use in high-temperature aerospace applications (up to 700°C), due to a combination of good mechanical properties, environmental resistance, and workability at moderate cost. These properties have led Alloy 718 to early adoption by selective laser melting (SLM) additive manufacturing. This presentation will share results from a comprehensive industry survey of 718 powder feedstock for SLM. The survey focuses on the impact of variability in powder characteristics on build quality, microstructure, tensile and high cycle fatigue in the as-fabricated and machined surface conditions. The investigation includes sixteen powder lots from eight suppliers that are produced by gas atomization or rotary atomization in argon or nitrogen. This research was previously presented and published at the 9th International Symposium on Superalloy 718 & Derivatives and was funded by NASA Space Launch System Liquid Engine Office with the Human Exploration Operations Mission Directorate.

Sudbrack, Chantal↗

Corrosion testing needs and considerations for additively manufactured materials in nuclear reactors

Metal additive manufacturing holds significant promise as an enabling technology for the 21st century nuclear energy industry. Metal additive manufacturing (MAM) can allow the fabrication of novel materials and innovative component designs that are not achievable through conventional manufacturing. Due to its very different fabrication methods, as-fabricated MAM components are characteristically different from conventionally manufactured components. MAM materials exhibit very different microstructures from conventional cast or wrought materials. For example, austenitic stainless steels fabricated by laser powder bed fusion exhibit columnar grain structures, dislocation cell structures, and melt pool fingerprints. In addition, MAM fabrication may result in defects such as porosity, incomplete processing of the feedstock (e.g., lack of fusion in melt-based methods), and oxide inclusions. Heat treatments may further evolve the microstructure, microsegregation, and stresses within the component. Furthermore, MAM components have a rough surface with feature sizes on the order of the feedstock material, as opposed to smooth surfaces resulting from conventional machining and forming operations. As a result, the corrosion behavior of MAM components will likely be significantly different from that of conventionally formed components. Corrosive environments for structural materials within advanced reactor environments include molten fluoride and chloride salts, liquid sodium and lead-bismuth, and high-temperature helium. The Advanced Materials and Manufacturing Technologies program within the Department of Nuclear Energy in the United States Department of Energy is assessing the unique concerns of MAM component corrosion and testing methodologies in advanced nuclear reactor environments. We discuss these concerns and testing strategies in this paper.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

(abstract) Optical Scattering and Surface Microroughness of Ion Beam Deposited Au and Pt Thin Films

Thin films of gold and platinum have been deposited onto superpolished fused silica substrates using thermal evaporation, ion assisted deposition (IAD), and ion assisted sputtering. The influence of ion beam flux, thin film material, and deposition rate on the films microroughness have been investigated. Short range surface microroughness of the films has been examined using scanning tunneling microscopy (STM) and atomic force microscopy (AFM). Long range surface microroughness has been characterized using an angle resolved optical scatterometer. Results indicate that ion beam deposited coatings have improved microstructure over thermally evaporated films.

assisted sputtering fused silica ion beam microrou↗

Microstructure analysis and machinability of additively manufactured A205 aluminum with heat treatments

A205 aluminum is one of the few high-strength aluminum alloys discovered for additive manufacturing (AM). The microstructure and heat treatment effects of AM A205 vary from those of its cast form, indicating possible differences in machinability during post-processing. Here, the objective of this research is to determine these variations of AM A205 and their effects on machinability using the cast condition as the baseline. As built and two heat-treated conditions (solution treatment and age hardening) were applied and compared in terms of their microstructures, micro-hardness, and machinability including vibration, specific cutting energy, chip morphology, and surface finish. The effects of print orientations on machinability were tested as well and found to be insignificant. AM as built had a higher hardness and slightly better machinability than its cast as built cast counterpart due to a smaller grain size (1 µm vs. 15 µm), eutectic θ-Al 2 Cu lattice and a fine, homogeneous TiB 2 distribution. The solution treatment dissolved this θ-Al 2 Cu lattice and increased the grain size (3 µm) which decreased the hardness, increased the ductility seen in the chips, and reduced the overall machinability. The presence of θ’-Al 2 Cu precipitates improved the machinability of aged AM A205. In addition, it was found that A205 exhibited both ductile and brittle behavior depending on the cutting speed, thus producing different machinability. The speed dependency is related to the material condition and heat treatment.

36 MATERIALS SCIENCE↗

Influence of Microstructure on the Absorption of Tritium into Gold-Plated 316 Stainless Steel

The interaction of tritium with metal surfaces is the initial step in the overall absorption of tritium by the substrate metal. As a result, limiting the adsorption of tritium to the surface may effectively reduce the quantity of tritium absorbed by a metal when it is in contact with tritium gas. To limit tritium adsorption, many tritium users electroplate gold onto the substrate metal. The gold layer is expected to reduce tritium adsorption, and subsequently absorption, by reducing water adsorption. The present work shows a comparison between tritium inventories in nonplated 316 stainless steel to the inventories in 316 stainless-steel samples electroplated with gold by various commercial vendors and laboratories. Of the various gold-plated samples, only one type of plating shows ~25% reduction in tritium inventory, relative to non-plated steel samples. The degree of tritium absorption appears to be significantly influenced by the porosity, texture, and completeness of the gold layer. Incomplete and/or porous layers lead to increased absorption, while gold layers with smaller surface features lead to similar tritium inventories as non-plated samples. Furthermore, reduced tritium absorption was observed only for complete gold layers with small surface features.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Microstructural characterization of the HRSI thermal protection system for space shuttle

Components of the space shuttle high temperature reusable surface insulation (HRSI) system were microscopically characterized, both separately and as a system, to obtain information needed for stress analysis models of the thermal protection system. A tension specimen of the HRSI system was loaded in steps and was microscopically observed at each load condition to demonstrate the tension failure mode associated with strain isolation pad (SIP) behavior. A local failure occurred which should be associated with transfer of load through transverse fibers in the SIP. Stress concentrations attributed to the SIP behavior necessitated strengthening of the HRSI by densification of the RSI at the bondline. An HRSI tile was microscopically characterized after the densification process. The densified surface layer blended into the RSI which caused a gradual change in density. The gradation in density does not appear to represent a sharp discontinuity in elastic modulus between the densified layer and the parent material.

Ransone, P. O.↗

Composite materials microstructure for radiation shielding

Shielding against radiation is a concern for applications on earth, in space, and on extraterrestrial surfaces. On earth EMI is an important factor, while in space and on extraterrestrial surfaces particle (high charge-Z and high energy-E) radiation is a critical issue. Conventional metallic materials currently used for EMI shielding incur large weight penalties. To overcome this weight penalty, ultra-lightweight composite materials utilizing fillers ranging from carbon microballoons to silver coated ceramic microballoons are proposed. The crucial shielding requirement is conductivity of the constituent materials, while the hollow microballoon geometry is utilized to yield low weight. Methods of processing and composition effects are examined and these results are compared to the effectiveness of varying the conductive microballoon material. The resulting ultralightweight materials, developed for EMI shielding, can be tailored through the application of the understanding of the relative effects of variables such as those tested. Initial experimental results reveal that these tailored ultralightweight composite materials are superior to traditional aluminum shielding at only a small fraction of the weight.

Radford, Donald W.↗

An Improved Instrument for Investigating Planetary Regolith Microstructure

The Opposition Effect (OE) is the non-linear increase in the intensity of light scattered from a surface as phase angle approaches 0 deg. It is seen in laboratory experiments and in remote sensing observations of planetary surfaces. Understanding the OE is a requirement for fitting photometric models which produce meaningful results about regolith texture. Previously we have reported measurements from the JPL long arm goniometer and we have shown that this instrument enables us to distinguish between two distinct processes which create the opposition surges, Shadow Hiding (SHOE) and Coherent Backscattering (CBOE). SHOE arises because, as phase angle approaches zero, shadows cast by regolith grains on other grains become invisible to the observer. CBOE results from constructive interference between rays traveling the same path but in opposite directions. Additional information is included in the original extended abstract.

Nelson, R. M.↗

A Multiphysics Study to Improve Specific Energy of Primary Batteries for Low Temperature Operation for Deep Space Missions

Several lander missions on the outer planets such as Europa, Enceladus, and Titan require electrical power to operate scientific and communication equipment. The traditional power generation methods, such as a photovoltaic array, are not feasible as their efficiency drops significantly at these vast distances. The novel radioisotope power systems are not practical today based on current lander designs and the effectiveness of these systems. To perform in situ science on distant planets, a high specific energy battery (>700 Wh/kg) needs to operate for about 480 hours under cold temperatures (-40C or 0C) [1]. While a primary battery such as Li-CFx can provide high specific energy at room temperature, its specific capacity decreases significantly at low temperatures. One of the causes for this drop is low ion and electrical conductivity, and slower reaction kinetics. Slower transport and facile kinetics lead to an increase in the battery’s resistance and higher voltage drops during the cell operation, thus reducing specific capacity. Both the transport and kinetics show a strong dependence on temperature. Thus, a small temperature rise can lead to an increase in the reaction rate and ion conductivity; since the temperature, cell resistance, and specific capacity are interdependent. A conventional battery model accounts for ohmic, thermodynamic, and, electrochemical, and chemical decomposition heating. The ohmic heating can be controlled by designing a resistive microstructure and varying the ratios of the active materials [2]. The kinetics can be improved by increasing the surface area, reducing the particle size, or adding a catalyst. These parameters are often optimized to achieve high specific energy at room temperatures. A similar optimization study is not available at low temperatures and for a primary (high specific energy) battery. For this presentation, we will explore the effect of geometrical, microstructural, and material properties on optimal specific capacity at low temperatures through multiphysics simulations. The ion transport resistance depends on the porosity and the tortuosity of an electrode and the separator.

M. Mehta↗

Applications of containerless processing in the studies of metals and alloys

The use of containerless processing in nucleation and microstructural studies of alloys is reviewed in terms of approaches and recent results. Drop-tube studies of niobium based on a statistical approach are discussed, and experiments are described which permit the study of the solidification front across the surface of a specimen. The various alloys studied are reviewed in terms of facilitated observations of metastability, chemical homogeneity, and microstructural refinement. Heterogeneous nucleation is reported for a preexponential factor of 10 exp 27 and a critical free energy of 46-56kT. The theoretical relationship between undercooling and solidification velocity correlates with containerless test observations at large solute concentrations. Containerless processing is effective for studying the properties of liquid metals or accessing the metastable thermodynamic regime.

Bayuzick, R. J.↗

Micro-structural features and material properties impact on adhesive metal joints via computational modeling and machine learning

The quality of structural bonding in practical applications depends on various factors arising from materials, pre-processing conditions, and manufacturing. Understanding how these factors influence bonding performance and determining their relative importance are of significant interest. Thus, this study evaluates the effects of microstructural features and material properties on the structural strength of adhesively-bonded metal joints at the submillimeter scale, utilizing a combination of Finite Element Modeling (FEM) and Machine Learning (ML) with Gradient Boosting Regression (GBR). The microstructural features include adhesive thickness, internal voids within the adhesive, adherend-adhesive interfacial voids, void size and volume fraction, and surface roughness. The material properties include the constitutive behavior of the adhesive, as well as the adherend-adhesive interfacial strength and fracture energy. The changes in structural strength and morphologies of the bonded metal structures with respect to different microstructural features and material properties were clarified by FEM. By further leveraging ML-GBR, the sequence of importance of these factors affecting bonding performance across various scenarios was summarized. This work provides valuable insights into the development of improved structural bonding for adhesive joints in industries such as automotive , aerospace, and beyond.

36 MATERIALS SCIENCE↗

Gradient nanostructuring via compositional means

Nanocrystalline metals are inherently unstable against thermal and mechanical stimuli, commonly resulting in significant grain growth. Also, while these metals exhibit substantial Hall-Petch strengthening, they tend to suffer from low ductility and fracture toughness. With regard to the grain growth problem, alloying elements have been employed to stabilize the microstructure through kinetic and/or thermodynamic mechanisms. And to address the ductility challenge, spatially-graded grain size distributions have been developed to facilitate heterogeneous deformation modes: high-strength at the surface and plastic deformation in the bulk. In the present work, we combine these two strategies and present a new methodology for the fabrication of gradient nanostructured metals via compositional means. Here, we have demonstrated that annealing a compositionally stepwise Pt-Au film with a homogenous microstructure results in a film with a spatial microstructural gradient, exhibiting grains which can be twice as wide in the bulk compared to the outer surfaces. Additionally, phase-field modeling was employed for the comparison with experimental results and for further investigation of the competing mechanisms of Au diffusion and thermally induced grain growth. This fabrication method offers an alternative approach for developing the next generation of microstructurally stable gradient nanostructured films.

36 MATERIALS SCIENCE↗

High-temperature oxidation behavior of the SiC layer of TRISO particles in low-pressure oxygen

Surrogate tristructural-isotropic (TRISO)-coated fuel particles were oxidized in 0.2 kPa O 2 at 1200–1600°C to examine the behavior of the SiC layer and understand the mechanisms. The thickness and microstructure of the resultant SiO 2 layers were analyzed using scanning electron microscopy, focused ion beam, and transmission electron microscopy. The majority of the surface comprised smooth, amorphous SiO 2 with a constant thickness indicative of passive oxidation. The apparent activation energy for oxide growth was 188 ± 8 kJ/mol and consistent across all temperatures in 0.2 kPa O 2 . The relationship between activation energy and oxidation mechanism is discussed. Raised nodules of porous, crystalline SiO 2 were dispersed across the surface, suggesting that active oxidation and redeposition occurred in those locations. These nodules were correlated with clusters of nanocrystalline SiC grains, which may facilitate active oxidation. So these findings suggest that microstructural inhomogeneities such as irregular grain size influence the oxidation response of the SiC layer of TRISO particles and may influence their accident tolerance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Investigating the Influence of Ni, ZrO 2 , and Y 2 O 3 from SOFC Anodes on Siloxane Deposition

Siloxanes, as a type of impurity in biogas, can poison the Ni-YSZ anode of SOFCs. However, the influence of individual components of the anode, such as Ni, ZrO 2 , and Y 2 O 3 , on the siloxane deposition process has not been investigated extensively. In this study, Ni, ZrO 2 , and Y 2 O 3 pellets were exposed to H 2 + N 2 + H 2 O + D4 (octamethylcyclotetrasiloxane, 2.5 ppmv) and H 2 + N 2 + D4 (2.5 ppmv siloxane) gas mixtures at 750 °C to investigate their affinity and tolerance for siloxane degradation. Surface morphology analysis and electrochemical analysis including electrochemical impedance spectroscopy (EIS), related distribution of relaxation times (DRT) analysis and equivalent circuit modeling with complex nonlinear least square (CNLS) fitting were conducted. Here, a microstructure parameter—tortuosity factor to porosity ratio $\tau /\varepsilon $ calculated by diffusion polarization resistance was utilized for siloxane deposition evaluation. After comparing pellets surface morphology changes before and after experiments and $\tau /\varepsilon $ change following the contamination, Ni is considered as a major factor in siloxane deposition reactions in Ni-YSZ anode.

25 ENERGY STORAGE↗

Microstructural Characterization of Felsite Fragments From the Apollo Next Generation Sample Analysis (ANGSA) Double Drive Tube 73001/73002

While the Moon’s surface is dominated by mafic igneous products formed through the crystallization of the lunar magma ocean, and the subsequent eruption of mare basalts – felsic magmatic fragments (variably referred to as felsites, granites, rhyolites or granophyres) have been identified from a number of Apollo samples (e.g. 12013[1], 14321[2], 15405[3] and 73215[4]). Magmatic edifices like the Gruithuisen Domes – silicic constructs sometimes found proximal to the basaltic mare provinces filling nearside basins, may represent a petrogenetic origin. However, this is, is complicated by the fact that they apparently predate mare volcanism (e.g. [5]). Additionally, crater-counting indicates that these silicic surface features also postdate radiogenic ages of Apollo felsites [6]. Various modes of felsic magmatism have been invoked to explain the presence of felsic lithologies on the Moon, including: 1) fractional crystallization and silicate liquid immiscibility; 2) partial melting of lunar crust through basaltic underplating; and 3) fractional crystallization of the mare parent magmas. Although these models are plausible, based on known Apollo samples and lunar meteorites, they are complicated by the lack of sample lithologies with intermediate composition between basaltic magmas and the felsic components, and the fact that partial melting of many crustal rock types on the Moon (e.g., anorthosite, troctolites) are unlikely to form granites. Along with other unique magmatic lithologies, new felsites have been identified within the < 1 mm size fractions of the ANGSA double drive core tube (73001/73002) from Apollo 17 station 3, sampling the light mantle landslide deposit from the South Massif [7]. These additional examples of lunar felsite will help us to better constrain the processes that lead to the formation of these evolved lithologies. To do this, we have employed a gambit of high-resolution scanning electron microscopy (SEM) and scanning transmission electron microscopy (TEM) analytical techniques, including electron backscatter diffraction (EBSD), cathodoluminescence and high-angle annular dark field (HAADF) imaging. These data provide unique insights into the felsite mineralogy and microstructures including the coexistence of quartz and tridymite in many of the fragments. In addition, these analyses provide petrological context and assist targeted in situ secondary ion mass spectrometry (SIMS) measurements of the U-Pb systematics of accessory minerals, and the volatile abundances and D/H ratios of apatite grains identified within the clasts.

lunar↗

Nanoscale lattice strains in self-ion implanted tungsten

Developing a comprehensive understanding of the modification of material properties by neutron irradiation is important for the design of future fission and fusion power reactors. Self-ion implantation is commonly used to mimic neutron irradiation damage, however an interesting question concerns the effect of ion energy on the resulting damage structures. The reduction in the thickness of the implanted layer as the implantation energy is reduced results in the significant quandary: Does one attempt to match the primary knock-on atom energy produced during neutron irradiation or implant at a much higher energy, such that a thicker damage layer is produced? In this work, we address this question by measuring the full strain tensor for two ion implantation energies, 2 MeV and 20 MeV in self-ion implanted tungsten, a critical material for the first wall and divertor of fusion reactors. A comparison of 2 MeV and 20 MeV implanted samples is shown to result in similar lattice swelling. Multi-reflection Bragg coherent diffractive imaging (MBCDI) shows that implantation induced strain is in fact heterogeneous at the nanoscale, suggesting that there is a non-uniform distribution of defects, an observation that is not fully captured by micro-beam Laue diffraction. At the surface, MBCDI and high-resolution electron back-scattered diffraction (HR-EBSD) strain measurements agree quite well in terms of this clustering/non-uniformity of the strain distribution. However, MBCDI reveals that the heterogeneity at greater depths in the sample is much larger than at the surface. This combination of techniques provides a powerful method for detailed investigation of the microstructural damage caused by ion bombardment, and more generally of strain related phenomena in micro-volumes that are inaccessible via any other technique.

36 MATERIALS SCIENCE↗