Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstrip”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Coplanar waveguide feeds for phased array antennas

The design and performance of the following coplanar waveguide (CPW) microwave distribution networks for linear as well as circularly polarized microstrip patches and printed dipole arrays is presented: (1) CPW/microstrip line feed; (2) CPW/balanced stripline feed; (3) CPW/slotline feed; (4) grounded CPW (GCPW)/balanced coplanar stripline feed; and (5) CPW/slot coupled feed. Typical measured radiation patterns are presented, and their relative advantages and disadvantages are compared.

Simons, Rainee N.↗

Performance of a Y-Ba-Cu-O superconducting filter/GaAs low noise amplifier hybrid circuit

A superconducting 7.3 GHz two-pole microstrip bandpass filter and a GaAs low noise amplifier (LNA) were combined into a hybrid circuit and characterized at liquid nitrogen temperatures. This superconducting/seismology circuit's performance was compared to a gold filter/GaAs LNA hybrid circuit. The superconducting filter/GaAs LNA hybrid circuit showed higher gain and lower noise figure than its gold counterpart.

Bhasin, Kul B.↗

35 GHz integrated circuit rectifying antenna with 33 percent efficiency

A 35 GHz integrated circuit rectifying antenna (rectenna) has been developed using a microstrip dipole antenna and beam-lead mixer diode. Greater than 33 percent conversion efficiency has been achieved. The circuit should have applications in microwave/millimeter-wave power transmission and detection.

Yoo, T.-W.↗

Ka-band active MMIC subarray development

A 4 x 8 array consisting of two adjacent 4 x 4 MMIC subarray modules under development as part of a MMIC insertion program for the ACTS communication experiments is presented. The subarray features a high-density 'tile' configuration integrating 16 MMIC power amplifiers and 16 MMIC phase shifters. The radiating elements are cavity-backed, aperture coupled, linearly polarized microstrip patches arranged on a 4 x 4 square grid. Each module also incorporates a MMIC controller to set the phase shifts and to turn individual amplifiers 'on' or 'off'. The novel module construction technique is expected to establish a benchmark in Ka-band and higher-frequency array architectures. The hybrid integration approach used for the module can be replaced by multifunctional chips and multilayer distribution boards. The higher level of integration is to permit the dense grid spacing required for wide-angle scanning and reduced size, weight, and cost for the array.

Lee, Richard↗

Lumped-element models characterize DR coupling effects

An approach to the analysis of closely spaced resonances produced by a microstrip coupled dielectric resonator is presented. In particular, it is shown that the use of a lumped-element model significantly simplifies the analysis. An experimental verification demonstrates that the model predicts the adjacent complementary resonances to within 1.6 percent of the measured value.

Hearn, Chase P.↗

A vertically integrated Ka-band phased array antenna

The design, development, and experimental demonstration of a small phased array antenna suitable for applications on communications satellites are discussed. Each of the vertical layers was optimized for performance, and MMICs on custom carriers were characterized prior to insertion. A vertical integration architecture is used which minimizes the size of the array with its associated beamforming network (BFN). The antenna features a four-element linear microstrip array that uses aperture coupling of the antenna elements to the BFN; a modified Wilkinson power divider BFN; and 32 Ghz, 4-bit MMIC phase shifters on customized alumina carriers. Performance data are presented for all components, and far-field antenna radiation patterns are given.

Kunath, R. R.↗

Theoretical and experimental development of 10 and 35 GHz rectennas

A 35 GHz rectenna has been developed with 39 percent conversion efficiency. The rectenna uses a microstrip dipole antenna and a commercially available mixer diode. Over 60 percent conversion efficiency was demonstrated using this diode at 10 GHz. A theoretical analysis was derived to predict the performance of the rectenna. The analysis is a useful tool for device and circuit design. The theoretical and experimental results should have many applications in microwave power transmission and detection.

Yoo, Tae-Whan↗

Electrical-transport properties and microwave device performance of sputtered TlCaBaCuO superconducting thin films

The paper describes the processing and electrical transport measurements for achieving reproducible high-Tc and high-Jc sputtered TlCaBaCuO thin films on LaAlO3 substrates, for microelectronic applications. The microwave properties of TlCaBaCuO thin films were investigated by designing, fabricating, and characterizing microstrip ring resonators with a fundamental resonance frequency of 12 GHz on 10-mil-thick LaAlO3 substrates. Typical unloaded quality factors for a ring resonator with a superconducting ground plane of 0.3 micron-thickness and a gold ground plane of 1-micron-thickness were above 1500 at 65 K. Typical values of penetration depth at 0 K in the TlCaBaCuO thin films were between 7000 and 8000 A.

Subramanyam, G.↗

A class of hybrid finite element methods for electromagnetics: A review

Integral equation methods have generally been the workhorse for antenna and scattering computations. In the case of antennas, they continue to be the prominent computational approach, but for scattering applications the requirement for large-scale computations has turned researchers' attention to near neighbor methods such as the finite element method, which has low O(N) storage requirements and is readily adaptable in modeling complex geometrical features and material inhomogeneities. In this paper, we review three hybrid finite element methods for simulating composite scatterers, conformal microstrip antennas, and finite periodic arrays. Specifically, we discuss the finite element method and its application to electromagnetic problems when combined with the boundary integral, absorbing boundary conditions, and artificial absorbers for terminating the mesh. Particular attention is given to large-scale simulations, methods, and solvers for achieving low memory requirements and code performance on parallel computing architectures.

Volakis, J. L.↗

Microwave characterization of slotline on high resistivity silicon for antenna feed network

Conventional silicon wafers have low resistivity and consequently unacceptably high value of dielectric attenuation constant. Microwave circuits for phased array antenna systems fabricated on these wafers therefore have low efficiency. By choosing a silicon substrate with sufficiently high resistivity it is possible to make the dielectric attenuation constant of the interconnecting microwave transmission lines approach those of GaAs or InP. In order for this to be possible, the transmission lines must be characterized. In this presentation, the effective dielectric constant (epsilon sub eff) and attenuation constant (alpha) of a slotline on high resistivity (5000 to 10 000 ohm-cm) silicon wafer will be discussed. The epsilon sub eff and alpha are determined from the measured resonant frequencies and the corresponding insertion loss of a slotline ring resonator. The results for slotline will be compared with microstrip line and coplanar waveguide.

Simons, Rainee N.↗

Lumped elements characterize Q in dielectric resonators

It has been earlier observed (Podcameni et al., 1981) that, as the coupling factor between a microstrip-coupled dielectric resonator and the line becomes much larger than unity, the unloaded quality factor (Q) of the resonator decreases. In this paper it is shown that this effect can be explained using lumped-element models of the coupling line, when the dielectric resonator is either overcoupled or undercoupled to the line.

Hearn, Chase P.↗

Performance of TlCaBaCuO 30 GHz 64 element antenna array

A 64-element, 30-GHz microstrip antenna array with corporate feed network was designed and built on a 0.254-mm (10-mil) thick lanthanum aluminate substrate. One antenna pattern was fabricated from gold film, and a second pattern used TlCaBaCuO high-temperature superconductor. Both antennas used gold ground planes deposited on the reverse side of the substrate. Gain and radiation patterns were measured for both antennas at room temperature and at cryogenic temperatures. Observations agree well with simple models for loss and microwave beam width, with a gain on boresight of 20.3 dB and beam width of 15 deg for the superconducting antenna. The antenna loss is only 1.9 dB.

Lewis, L. L.↗

Novel miniaturised wideband baluns for MIC and MMIC applications

Very compact novel planar broadband baluns are described. Each balun consists of two Lange couplers. Less than 0.3 dB and 2.5 deg for the amplitude and phase balances, respectively, have been measured over the 1.0-2.2 GHz bandwidth for a microstrip balun. As compared with other reported baluns, these baluns are simpler, more compact, easier to design, and fabricated on only one side of the substrate. They are thus very attractive for microwave integrated and monolithic integrated circuit applications.

Nguyen, C.↗

Hermetic Packages For Millimeter-Wave Circuits

Advanced hermetic packages developed to house electronic circuits operating at frequencies from 1 to 100 gigahertz and beyond. Signals coupled into and out of packages electromagnetically. Provides circuit packages small, lightweight, rugged, and inexpensive in mass production. Packages embedded in planar microstrip and coplanar waveguide circuits, in waveguide-to-planar and planar-to-waveguide circuitry, in waveguide-to-waveguide circuitry, between radiating (antenna) elements, and between planar transmission lines and radiating elements. Other applications in automotive, communication, radar, remote sensing, and biomedical electronic systems foreseen.

Herman, Martin I.↗

Analysis and characterizations of planar transmission structures and components for superconducting and monolithic integrated circuits

The research effort was continued to design and characterize superconducting transmission line structures. The research during this period was concentrated on the implementation of a superconductor into coplanar waveguide structures. First, the superconducting coplanar waveguide was examined, and compared with a superconducting microstrip line in terms of loss characteristics and their design aspects. Then, the research was carried on the design and characterization of the coplanar waveguide family in the packaging environment. The transition between the coaxial line to the conductor backed coplanar waveguide was also designed for the measurement of the superconducting conductor backed coplanar waveguide.

Itoh, Tatsuo↗

Ten Ghz YBa2Cu3O(7-Delta) Superconducting Ring Resonators on NdGaO3 Substrates

YBa2Cu3O(7-delta) thin films were formed on NdGaO3 substrates by laser ablation. Critical temperatures greater than 89 K and critical current densities exceeding 2 x 10(exp 8) Acm(sub -2) at 77 K were obtained. The microwave performance of films patterned into microstrip ring resonators with gold ground planes was measured. An unloaded quality factor six times larger than that of a gold resonator of identical geometry was achieved. The unloaded quality factor decreased below 70 K for both the superconducting and gold resonators due to increasing dielectric losses in the substrate. The temperature dependence of the loss tangent of NdGaO3 was extracted from the measurements.

To, H. Y.↗

Microwave properties and characterization of co-evaporated BSCCO thin films

An extensive characterization of Bi-Sr-Ca-Cu-O (BSCCO) thin films deposited by co-evaporation on LaAlO3 and SrTiO3 substrates was performed. The films had a T(sub c) (R = O) of approximately 78 K, and were predominantly c-axis oriented, with critical current densities (J(sub c)) at 4.5 K of 1.6 x 10(exp 6) and 1.1 x 10(exp 6) A cm(sup -2), for the samples on SrTiO3 and LaAlO3, respectively. The microwave properties of the films were examined by three techniques. The complex conductivity sigma(sub *) = sigma(sub 1) - j(sigma(sub 2)) and the magnetic penetration depth (A) were measured by power transmission at 30.6 GHz; the surface resistance (R(sub s)) was measured using a cavity resonator at 58.9 GHz, and the transmission line losses were determined by measuring the quality factor (Q) of a linear microstrip resonator at 10.4 and 20.2 GHz. The complex conductivity for the film on LaAlO3 was determined to be (2.0-j10) x 10(exp 5) S/m at 77 K. It was observed that in the superconducting state sigma(sub 1) deviates from both the Bardeen-Cooper-Schrieffer (BCS) theory and the two-fluid model. Values of lambda were found to be approximately 2.0 and 1.1 microns at 77 K and 20 K respectively, and were obtained for the film on LaAlO3. The value of lambda at 20 K was approximately three times larger than that of BSCCO single crystals. R(sub s) values of 865 and 1391 mOmega were obtained for the films on SrTiO3 and LaAlO3, respectively, at 77 K and 58.9 GHz. Unloaded Q factors at 20 K of approximately 1100 and 800 at 10.4 and 20.2 GHz respectively, were measured for the BSCCO resonator. Unloaded Q values of 290 and 405 at 20 K were obtained at 10.4 GHz and 20.2 GHz respectively, for an all gold (Au) resonator.

Miranda, F. A.↗

Linearly tapered slot antenna circular array for mobile communications

The design, fabrication and testing of a conformal K-band circular array is presented. The array consists of sixteen linearly tapered slot antennas (LTSA). It is fed by a 1:16 microstrip line power splitter via electromagnetic coupling. The array has an omni-directional pattern in the azimuth plane. In the elevation plane the beam is displaced above the horizon.

Simons, Rainee N.↗