Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “loading frequency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Unusual ISS Rate Signature

On November 23, 2011 International Space Station Guidance, Navigation, and Control reported unusual pitch rate disturbance. These disturbances were an order of magnitude greater than nominal rates. The Loads and Dynamics team was asked to review and analyze current accelerometer data to investigate this disturbance. This paper will cover the investigation process under taken by the Loads and Dynamics group. It will detail the accelerometers used and analysis performed. The analysis included performing Frequency Fourier Transform of the data to identify the mode of interest. This frequency data is then reviewed with modal analysis of the ISS system model. Once this analysis is complete and the disturbance quantified, a forcing function was produced to replicate the disturbance. This allows the Loads and Dynamics team to report the load limit values for the 100's of interfaces on the ISS.

Laible, Michael R.↗
NASA NTRSDate not supplied

Fluid-Thermal-Structural Interactions in Ramp-Induced Shock-Wave Boundary-Layer Interactions at Mach 6

Shock-wave boundary-layer interactions (SWBLI) pose unique challenges for the slender airframes and sharp control surfaces characteristic of high-speed airbreathing aircraft. Spikes in pressure and thermal loading have been shown to occur in SWBLI regions; thus, predicting their location and behavior proves critical for assuring aircraft structural integrity and fatigue resilience. SWBLIs frequently lead to severe turbulent boundary-layer separation and corresponding unsteady motions characterized by a wide range of frequencies. Low-frequency motion has been shown to couple with the structure of a compliant panel, and turbulent boundary layers thus present a particular danger for thin control surfaces. Previous studies have shown that the thermal loading on a compliant panel in a ramp-induced SWBLI may have a signi cant impact on the panel vibrations. A multitude of studies has investigated the heating on rigid structures, but a charactrization of the heating effects on compliant structures is necessary to fully understand the fluid-thermal-structural interactions (FTSI) occurring in ramp-induced SWBLIs. This studuses infrared thermography and high-frequency Kulite pressure transducers to examine the heating loads on rigid and compliant ramps at various angles and flow conditions at Mach 6.

Hypersonic↗
NASA NTRS2011

Characterization of Deficiencies in the Frequency Domain Forced Response Analysis Technique for Supersonic Turbine Bladed Disks

Turbine blades in rocket and jet engine turbomachinery experience enormous harmonic loading conditions. These loads result from the integer number of upstream and downstream stator vanes as well as the other turbine stages. Assessing the blade structural integrity is a complex task requiring an initial characterization of whether resonance is possible and then performing a forced response analysis if that condition is met. The standard technique for forced response analysis in rocket engines is to decompose a CFD-generated flow field into its harmonic components, and to then perform a frequency response analysis at the problematic natural frequencies. Recent CFD analysis and water-flow testing at NASA/MSFC, though, indicates that this technique may miss substantial harmonic and non-harmonic excitation sources that become present in complex flows. A substantial effort has been made to account for this denser spatial Fourier content in frequency response analysis (described in another paper by the author), but the question still remains whether the frequency response analysis itself is capable of capturing the excitation content sufficiently. Two studies comparing frequency response analysis with transient response analysis, therefore, of bladed-disks undergoing this complex flow environment have been performed. The first is of a bladed disk with each blade modeled by simple beam elements. Six loading cases were generated by varying a baseline harmonic excitation in different ways based upon cold-flow testing from Heritage Fuel Air Turbine Test. It was hypothesized that the randomness and other variation from the standard harmonic excitation would reduce the blade structural response, but the results showed little reduction. The second study was of a realistic model of a bladed-disk excited by the same CFD used in the J2X engine program. It was hypothesized that enforcing periodicity in the CFD (inherent in the frequency response technique) would overestimate the response. The results instead showed that the transient analysis results were up to 10% higher for "clean" nodal diameter excitations and six times larger for "messy" excitations, where substantial Fourier content around the main harmonic exists. Because the bulk of resonance problems are due to the "clean" excitations, a 10% underprediction is not necessarily a problem, especially since the average response in the transient is similar to the frequency response result, and so in a realistic finite life calculation, the life would be same. However, in the rare cases when the "messy" excitations harmonics are identified as the source of potential resonance concerns, this research does indicate that frequency response analysis is inadequate for accurate characterization of blade structural capability.

Brown, Andrew M.↗
NASA NTRS1984

Noise and performance characteristics of a model scale X-wing rotor system in hover

Noise data for the hover condition were measured for a 8 m diameter X-wing model rotor mounted on an outdoor whirl tower. The noise was found to be a function of operating condition, in general increasing with performance. The X-wing spectra obtained from narrowband and 1/3-octave band analyses were dominated by the blade passage frequency harmonics. The circulation control slot blowing produced 1 to 10 kHz broadband noise which exhibited a jet velocity to the 5.4 dependency. Under the rotor plane loading noise was dominant, except at low values of blade pressure ratio where a sharp decrease in the blade passage frequency harmonic levels was observed. In the rotor plane, the contribution of the broadband noise sources was greater than under the rotor plane. The X-wing rotor system in hover exhibited flexibility in operating conditions to achieve a specific level of performance. The high collective, low blade passage ratio combinations which meet a given level of performance were associated with low overall sound pressure levels.

Willshire, W. L., Jr.↗
NASA NTRSDate not supplied

Fluid-Thermal-Structural Interactions in Ramp-Induced Shock-Wave Boundary-Layer Interactions at Mach6

Shock-wave boundary-layer interactions (SWBLI) pose unique challenges for the slender airframes and sharp control surfaces characteristic of high-speed airbreathing aircraft. Spikes in pressure and thermal loading have been shown to occur in SWBLI regions; thus, predicting their location and behavior proves critical for assuring aircraft structural integrity and fatigue resilience. SWBLIs frequently lead to severe turbulent boundary-layer separation and corresponding unsteady motions characterized by a wide range of frequencies. Low-frequency motion has been shown to couple with the structure of a compliant panel, and turbulent boundary layers thus present a particular danger for thin control surfaces. Previous studies have shown that the thermal loading on a compliant panel in a ramp-induced SWBLI may have a signi cant impact on the panel vibrations. A multitude of studies has investigated the heating on rigid structures, but a charactrization of the heating effects on compliant structures is necessary to fully understand the fluid-thermal-structural interactions (FTSI) occurring in ramp-induced SWBLIs. This studuses infrared thermography and high-frequency Kulite pressure transducers to examine the heating loads on rigid and compliant ramps at various angles and flow conditions at Mach 6.

Hypersonic↗
NASA NTRS2003

Effects of broad frequency vibration on cultured osteoblasts

Bone is subjected in vivo to both high amplitude, low frequency strain, incurred by locomotion, and to low amplitude, broad frequency strain. The biological effects of low amplitude, broad frequency strain are poorly understood. To evaluate the effects of low amplitude strains ranging in frequency from 0 to 50 Hz on osteoblastic function, we seeded MC3T3-E1 cells into collagen gels and applied the following loading protocols for 3 min per day for either 3 or 7 days: (1) sinusoidal strain at 3 Hz, with 0-3000 microstrain peak-to-peak followed by 0.33 s resting time, (2) "broad frequency vibration" of low amplitude strain (standard deviation of 300 microstrain) including frequency components from 0 to 50 Hz, and (3) sinusoidal strain combined with broad frequency vibration (S + V). The cells were harvested on day 4 or 8. We found that the S + V stimulation significantly repressed cell proliferation by day 8. Osteocalcin mRNA was up-regulated 2.6-fold after 7 days of S + V stimulation, and MMP-9 mRNA was elevated 1.3-fold after 3 days of vibration alone. Sinusoidal stimulation alone did not affect the cell responses. No differences due to loading were observed in alkaline phosphatase activity and in mRNA levels of type I collagen, osteopontin, connexin 43, MMPs-1A, -3, -13. These results suggest that osteoblasts are more sensitive to low amplitude, broad frequency strain, and this kind of strain could sensitize osteoblasts to high amplitude, low frequency strain. This suggestion implies a potential contribution of stochastic resonance to the mechanical sensitivity of osteoblasts. Copyright 2002 Elsevier Science Ltd.

Non-NASA Center↗
NASA NTRS1952

Matrix Method of Determining the Longitudinal-Stability Coefficients and Frequency Response of an Aircraft from Transient Flight Data

A matrix method is presented for determining the longitudinal-stability coefficients and frequency response of an aircraft from arbitrary maneuvers. The method is devised so that it can be applied to time-history measurements of combinations of such simple quantities as angle of attack, pitching velocity, load factor, elevator angle, and hinge moment to obtain the over-all coefficients. Although the method has been devised primarily for the evaluation of stability coefficients which are of primary interest in most aircraft loads and stability studies, it can be used also, with a simple additional computation, to determine the frequency-response characteristics. The entire procedure can be applied or extended to other problems which can be expressed by linear differential equations.

Donegan, James J↗
NASA NTRS2012

Flexible Launch Vehicle Stability Analysis Using Steady and Unsteady Computational Fluid Dynamics

Launch vehicles frequently experience a reduced stability margin through the transonic Mach number range. This reduced stability margin can be caused by the aerodynamic undamping one of the lower-frequency flexible or rigid body modes. Analysis of the behavior of a flexible vehicle is routinely performed with quasi-steady aerodynamic line loads derived from steady rigid aerodynamics. However, a quasi-steady aeroelastic stability analysis can be unconservative at the critical Mach numbers, where experiment or unsteady computational aeroelastic analysis show a reduced or even negative aerodynamic damping.Amethod of enhancing the quasi-steady aeroelastic stability analysis of a launch vehicle with unsteady aerodynamics is developed that uses unsteady computational fluid dynamics to compute the response of selected lower-frequency modes. The response is contained in a time history of the vehicle line loads. A proper orthogonal decomposition of the unsteady aerodynamic line-load response is used to reduce the scale of data volume and system identification is used to derive the aerodynamic stiffness, damping, and mass matrices. The results are compared with the damping and frequency computed from unsteady computational aeroelasticity and from a quasi-steady analysis. The results show that incorporating unsteady aerodynamics in this way brings the enhanced quasi-steady aeroelastic stability analysis into close agreement with the unsteady computational aeroelastic results.

Bartels, Robert E.↗
NASA NTRS1977

Comparison of effects of unsteady lift and spanwise averaging in flight through turbulence

Gust loads on aircraft flying through random atmospheric turbulence are attenuated at high frequencies by the effects of unsteady lift and spanwise averaging. Previously derived theoretical results for these two effects are placed in a form which makes direct comparison possible. The attenuation effects from each cause are found to be of approximately equal magnitude for unswept wings of moderate aspect ratio. For small values of the ratio of wingspan to scale of turbulence, the attenuation due to spanwise averaging is a function only of reduced frequency based on wingspan and is independent of the ratio of wingspan to scale of turbulence.

Phillips, W. H.↗
NASA NTRS1979

Random harmonic analysis program, L221 (TEV156). Volume 1: Engineering and usage

A digital computer program capable of calculating steady state solutions for linear second order differential equations due to sinusoidal forcing functions is described. The field of application of the program, the analysis of airplane response and loads due to continuous random air turbulence, is discussed. Optional capabilities including frequency dependent input matrices, feedback damping, gradual gust penetration, multiple excitation forcing functions, and a static elastic solution are described. Program usage and a description of the analysis used are presented.

Miller, R. D.↗
NASA NTRS1988

Design Procedures for Fiber Composite Box Beams

Step-by-step procedures are described which can be used for the preliminary design of fiber composite box beams subjected to combined loadings. These procedures include a collection of approximate closed-form equations so that all the required calculations can be performed using pocket calculators. Included is an illustrated example of a tapered cantilever box beam subjected to combined loads. The box beam is designed to satisfy strength, displacement, buckling, and frequency requirements.

Chamis, Christos C.↗
NASA NTRS1988

Pressure measurements of impinging jet with asymmetric nozzle

For modern aircraft, impinging surfaces are commonly used as a device for obtaining vector thrust from engine exhaust. The nature of dynamic loading is important to understand for design purposes. In this study, the frequency, mode, and level of pressure fluctuations generated by an elliptic jet are examined. The elliptic jet is used because it has several operational advantages over a circular jet.

Ho, Chih-Ming↗
NASA NTRS1989

Design procedures for fiber composite box beams

Step-by-step procedures are described which can be used for the preliminary design of fiber composite box beams subjected to combined loadings. These procedures include a collection of approximate closed-form equations so that all the required calculations can be performed using pocket calculators. Included is an illustrative example of a tapered cantilever box beam subjected to combined loads. The box beam is designed to satisfy strength, displacement, buckling, and frequency requirements.

Chamis, Cristos C.↗
NASA NTRS1989

Static and free-vibrational response of semi-circular graphite-epoxy frames with thin-walled open sections

Experiments were conducted to measure the three-dimensional static and free vibrational response of two graphite-epoxy, thin-walled, open section frames. The frames are semi-circular with a radius of three feet, and one specimen has an I cross section and the other has a channel cross section. The flexibility influence coefficients were measured in static tests for loads applied at midspan with the ends of the specimens clamped. Natural frequencies and modes were determined from vibrational tests for free and clamped end conditions. The experimental data is used to evaluate a new finite element which was developed specifically for the analysis of curved, thin-walled structures. The formulation of the element is based on a Vlasov-type, thin-walled, curved beam theory. The predictions from the finite element program generally correlated well with the experimental data for the symmetric I-specimen. Discrepancies in some of the data were found to be due to flexibility in the clamped end conditions. With respect to the data for the channel specimen, the correlation was less satisfactory. The finite element analysis predicted the out-of-plane response of the channel specimen reasonably well, but large discrepancies occurred between the predicted in-plane response and the experimental data. The analysis predicted a much more compliant in-plane response than was observed in the experiments.

Collins, J. Scott↗
NASA NTRS1990

Counter-rotating propellant analysis using a frequency domain panel method

The unsteady aerodynamic coupling between the front and rear rotors in a counter-rotating propeller system is analyzed using a frequency-domain panel method based on linear compressible aerodynamic theory. The periodic loads are decomposed into harmonics, and the harmonic amplitudes are found iteratively. Each stage of the interation involves the solution of an isolated propeller problem, the interaction being done through the Fourier transform of the induced velocity field. The method was validated by comparing mean performance parameters with measured data and by comparing the predicted velocity field with detailed laser Doppler velocimeter measurements. Comparisons have also been made between the fluctuating loads predicted by the present method and a time-domain panel method.

Williams, Marc H.↗
NASA NTRS1991

Comparison of structural performance of one- and two-bay rotary joints for truss applications

The structural performance of one- and two-bay large-diameter discrete-bearing rotary joints was addressed for application to truss-beam structures such as the Space Station Freedom. Finite element analyses are performed to determine values for rotary joint parameters that give the same bending vibration frequency as the parent truss beam. The structural masses and maximum internal loads of these joints are compared to determine their relative structural efficiency. Results indicate that no significant difference exists in the masse of one- and two-bay rotary joints. This conclusion is reinforced with closed-form calculations of rotary joint structural efficiency in extension. Also, transition truss-member loads are higher in the one-bay rotary joint. However, because of the increased buckling strength of these members, the external load-carrying capability of the one-bay concept is higher than that of the two-bay concept.

Vail, J. Douglas↗