Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “link layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Design of a pressurized lunar rover

A pressurized lunar rover is necessary for future long-term habitation of the moon. The rover must be able to safely perform many tasks, ranging from transportation and reconnaissance to exploration and rescue missions. Numerous designs were considered in an effort to maintain a low overall mass and good mobility characteristics. The configuration adopted consists of two cylindrical pressure hulls passively connected by a pressurized flexible passageway. The vehicle has an overall length of 11 meters and a total mass of seven metric tons. The rover is driven by eight independently powered two meter diameter wheels. The dual-cylinder concept allows a combination of articulated frame and double Ackermann steering for executing turns. In an emergency, the individual drive motors allow the option of skid steering as well. Two wheels are connected to either side of each cylinder through a pinned bar which allows constant ground contact. Together, these systems allow the rover to easily meet its mobility requirements. A dynamic isotope power system (DIPS), in conjunction with a closed Brayton cycle, supplied the rover with a continuous supply of 8.5 kW. The occupants are all protected from the DIPS system's radiation by a shield of tantalum. The large amount of heat produced by the DIPS and other rover systems is rejected by thermal radiators. The thermal radiators and solar collectors are located on the top of the rear cylinder. The solar collectors are used to recharge batteries for peak power periods. The rover's shell is made of graphite-epoxy coated with multi-layer insulation (MLI). The graphite-epoxy provides strength while the thermally resistant MLI gives protection from the lunar environment. An elastomer separates the two materials to compensate for the thermal mismatch. The communications system allows for communication with the lunar base with an option for direct communication with earth via a lunar satellite link. The various links are combined into one signal broadcast in the S-band at 2.3 GHz. The rover is fitted with a parabolic reflector disk for S-band transmission, and an omnidirectional antenna for local extravehicular activity (EVA) communication. The rover's guidance, navigation, and control subsystem consists of an inertial guidance system, an orbiting lunar satellite, and an obstacle avoidance system. In addition, the rover is equipped with a number of external fixtures including two telerobotic arms, lights, cameras, EVA storage, manlocks, a docking fixture, solar panels, thermal radiators, and a scientific airlock. In conclusion, this rover meets all of the design requirements and clearly surpasses them in the areas of mobility and maneuverability.

Bhardwaj, Manoj↗

Dependence of wind-farm-induced gravity waves and wind farm performance on non-dimensional atmospheric parameters and simulation configuration

This large-eddy simulation (LES) study examines how wind-farm-induced atmospheric gravity waves (AGWs) and wind farm performance depend on non-dimensional atmospheric parameters and simulation configuration. A hypothetical aligned wind farm of actuator disks is simulated under neutral surface conditions, with a stable capping inversion and a mildly stable free atmosphere, to assess the effects of stratification beyond the atmospheric boundary layer (ABL) on ABL flow. Simulation set-ups fully resolving AGWs are validated to minimize spurious wave generation and reflection from the domain boundaries. The validated set-up is then used to analyze AGW types and characteristics, as well as stratification impacts under conventionally neutral boundary layer (CNBL) conditions. These conditions are governed by four non-dimensional parameters: the Froude numbers of the free atmosphere and capping inversion (Fr, Fr i ), and the aspect ratios of the ABL and wind farm (H̃ i , S h ). Simulation configurations that fully resolve AGWs – capturing at least one wavelength both horizontally and vertically – yield the most realistic stratification effects on ABL flow, whereas partial or unresolved configurations produce non-physical, channel-like behavior. A coherent description of the AGW phenomena is provided, highlighting the central role of capping inversion displacement in linking ABL fluctuations with AGWs. Trapped waves are confined within the capping inversion, while interfacial and internal waves aloft are identified as the AGW types most relevant to wind farm performance. The wavy inversion, analogous to an interfacial wave, forms converging and diverging zones that drive power fluctuations across the farm. The interfacial wavelength, measured over the wind farm, corresponds to one diverging, one converging, and one mildly diverging zone. As the interfacial wavelength decreases with Fr i , multiple convergence–divergence zones develop under sub-critical conditions (Fr i <1.0), while for super-critical conditions (Fr i > 1.0), the wavelength approaches the farm length. Wave amplitude increases with decreasing H̃ i (i.e., shallower capping inversions). Wind farm performance is most sensitive to H̃ i : shallow boundary layers increase blockage and reduce efficiency, while deeper layers enhance efficiency. Increasing Fr and Fr i mitigates blockage, and increasing S h mainly improves wake recovery. Although local power fluctuations arise from AGWs, overall wind farm efficiency remains nearly constant with Fr and Fr i , improving primarily with larger H̃ i and S h .

17 WIND ENERGY↗

Tropical Ocean Surface Energy Balance Variability: Linking Weather to Climate Scales

Radiative and turbulent surface exchanges of heat and moisture across the atmosphere-ocean interface are fundamental components of the Earth s energy and water balance. Characterizing the spatiotemporal variability of these exchanges of heat and moisture is critical to understanding the global water and energy cycle variations, quantifying atmosphere-ocean feedbacks, and improving model predictability. These fluxes are integral components to tropical ocean-atmosphere variability; they can drive ocean mixed layer variations and modify the atmospheric boundary layer properties including moist static stability, thereby influencing larger-scale tropical dynamics. Non-parametric cluster-based classification of atmospheric and ocean surface properties has shown an ability to identify coherent weather regimes, each typically associated with similar properties and processes. Using satellite-based observational radiative and turbulent energy flux products, this study investigates the relationship between these weather states and surface energy processes within the context of tropical climate variability. Investigations of surface energy variations accompanying intraseasonal and interannual tropical variability often use composite-based analyses of the mean quantities of interest. Here, a similar compositing technique is employed, but the focus is on the distribution of the heat and moisture fluxes within their weather regimes. Are the observed changes in surface energy components dominated by changes in the frequency of the weather regimes or through changes in the associated fluxes within those regimes? It is this question that the presented work intends to address. The distribution of the surface heat and moisture fluxes is evaluated for both normal and non-normal states. By examining both phases of the climatic oscillations, the symmetry of energy and water cycle responses are considered.

Roberts, J. Brent↗

Complexions at the iron-magnetite interface

Synthesizing distinct phases and controlling crystalline defects are key concepts in materials design. These approaches are often decoupled, with the former grounded in equilibrium thermodynamics and the latter in nonequilibrium kinetics. By unifying them through defect phase diagrams, we can apply phase equilibrium models to thermodynamically evaluate defects—including dislocations, grain boundaries, and phase boundaries—establishing a theoretical framework linking material imperfections to properties. Using scanning transmission electron microscopy (STEM) with differential phase contrast (DPC) imaging, we achieve the simultaneous imaging of heavy Fe and light O atoms, precisely mapping the atomic structure and chemical composition at the iron-magnetite (Fe/Fe 3 O 4 ) interface. We identify a well-ordered two-layer interface-stabilized phase state (referred to as complexion) at the Fe[001]/Fe 3 O 4 [001] interface. Using density-functional theory (DFT), we explain the observed complexion and map out various interface-stabilized phases as a function of the O chemical potential. The formation of complexions increases interface adhesion by 20% and alters charge transfer between adjacent materials, impacting transport properties. Our findings highlight the potential of tunable defect-stabilized phase states as a degree of freedom in materials design, enabling optimized corrosion protection, catalysis, and redox-driven phase transitions, with applications in materials sustainability, efficient energy conversion, and green steel production.

36 MATERIALS SCIENCE↗

Spin-Canting-Induced Band Reconstruction in the Dirac Material Ca 1 – x Na x MnBi 2

The ternary A MnBi 2 ( A is alkaline as well as rare-earth atom) materials provide an arena for investigating the interplay between low-dimensional magnetism of the antiferromagnetic MnBi layers and the electronic states in the intercalated Bi layers, which harbor relativistic fermions. We report on a comprehensive study of the optical properties and magnetic torque response of Ca 1–x Na x MnBi 2 . Our findings give evidence for a spin canting occurring at T s ~50–100 K. Thus, with the support of first-principles calculations we establish a direct link between the spin canting and the reconstruction of the electronic band structure, having immediate implications for the spectral weight reshuffling in the optical response, signaling a partial gapping of the Fermi surface, and the dc transport properties below T s .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Promotion of superconductivity in magic-angle graphene multilayers

Graphene moiré superlattices show an abundance of correlated insulating, topological, and superconducting phases. Whereas the origins of strong correlations and nontrivial topology can be directly linked to flat bands, the nature of superconductivity remains enigmatic. We demonstrate that magic-angle devices made of twisted tri-, quadri-, and pentalayer graphene placed on monolayer tungsten diselenide exhibit flavor polarization and superconductivity. We also observe insulating states in the tril- and quadrilayer arising at finite electric displacement fields. As the number of layers increases, superconductivity emerges over an enhanced filling-factor range, and in the pentalayer it extends well beyond the filling of four electrons per moiré unit cell. Our results highlight the role of the interplay between flat and more dispersive bands in extending superconducting regions in graphene moiré superlattices.

Science & Technology - Other Topics↗

Processes Associated with Boundary Layer Cloud Ice Phase Precipitation in the High Southern Latitudes (Final Technical Report)

This is a final technical report for DOE Award No. DE-SC0018995. Using data collected during the MARCUS deployment of the 2nd ARM mobile facility, this project sought to address the following scientific questions: 1. What are the conditions that govern phase partitioning in supercooled boundary layer clouds over the high latitude Southern Oceans? 2. To what extent are supercooled mixed phase clouds responsible for the high cloud fractions over the Southern Ocean and do these mixed phase clouds contribute to the model biases in absorbed shortwave radiation? 3. Can the cloud properties and phase partitioning over the Southern Ocean be linked to the underlying aerosol environment? 4. How do the aerosol properties at the surface vary spatially and seasonally over the high latitude Southern Ocean and what processes control these features? 5. How well defined are the atmospheric compositional boundaries between Southern Ocean marine, Antarctic free tropospheric, and Antarctic surface airmasses, and how does this influence the chemistry and physics of the Southern Ocean atmosphere? In this project we published three peer review journal articles that address these questions.

54 ENVIRONMENTAL SCIENCES↗

Improving the Simulation of Sea Ice Lead Conditions and Turbulent Fluxes Using RGPS Products and Merged RADARSAT, AVHRR and MODIS Data

The importance of sea ice leads in the ice-ocean-atmosphere system lies in the fact that each of the boxes in the 'surface processes' interface in this diagram is closely linked to lead conditions. For example, heat, moisture and salt exchange between the Ocean and atmosphere within the ice pack occur nearly entirely through leads. The shear, divergence and convergence associated with lead formation and closure alter surface and basal roughness and topography, which in turn affects momentum transfer in the atmosphere and ocean boundary layers, and modifies the accumulation of snow on the ice surface, which then affects heat conduction and summertime albedo. In addition to providing openings for loss of heat and moisture fluxes to the atmosphere, leads absorb solar energy, which is used to melt ice and is transmitting to the underlying ocean. Given that leads dominate the ice-ocean interface in this manner, then it stands to reason that focusing on lead treatments within models can identify performance limitations of models and yield routes for significant improvements.

Maslanik, James A.↗

Initiation of Long-Wave Instability of Vortex Pairs at Cruise Altitudes

Previous studies have usually attributed the initiation of the long-wave instability of a vortex pair to turbulence in the atmosphere or in the wake of the aircraft. The purpose here is to show by use of observations and photographs of condensation trails shed by aircraft at cruise altitudes that another initiating mechanism is not only possible but is usually the mechanism that initiates the long-wave instability at cruise altitudes. The alternate initiating mechanism comes about when engine thrust is robust enough to form an array of circumferential vortices around each jet-engine-exhaust stream. In those cases, initiation begins when the vortex sheet shed by the wing has rolled up into a vortex pair and descended to the vicinity of the inside bottom of the combined shear-layer vortex arrays. It is the in-and-out (up and down) velocity field between sequential circumferential vortices near the bottom of the array that then impresses disturbance waves on the lift-generated vortex pair that initiate the long-wave instability. A time adjustment to the Crow and Bate estimate for vortex linking is then derived for cases when thrust-based linking occurs.

Rossow, Vernon J.↗

Prototype Magnetic Calorimeter Arrays with Buried Wiring for the Lynx X-Ray Microcalorimeter

Metallic magnetic calorimeter (MMC) technology is a leading contender for detectors for the Lynx X-ray Microcalorimeter, which is an imaging spectrometer consisting of an array of greater than 100,000 pixels. The fabrication of such large arrays presents a challenge when attempting to route the superconducting wiring from the pixels to the multiplexed readout. If the wiring is designed to be planar, then an aggressive, submicron scale wiring pitch has to be employed, which is technically challenging to design and fabricate on account of the requirements of low inductance, low cross-talk, high critical currents and high yield. An alternative way to achieve large scale, high density wiring is through the use of multiple buried metal layers, planarized by Chemical Mechanical Planarization. This approach is well-suited for connecting thousands of pixels on a large focal plane to readout chips, and also for fabricating sensor meander coils with narrow line widths, which helps in increasing the sensor inductance and thus alleviates stray inductance issues associated with the wiring in large size arrays. In this work we describe the fabrication of high sensor inductance MMC arrays implementing Lynx concepts and incorporating multiple layers of buried Nb wiring. The detector array is composed of three sub-arrays with pixels optimized to meet the different science driven performance requirements of Lynx. In two of the sub-arrays we adopt a thermal multiplexing scheme to read out pixels by coupling 25 absorbers to a single sensor through thermal links of varied thermal conductance. We demonstrate the successful fabrication of multi-absorber MMCs with fine pitch pixels in very large size arrays.

Solid-State Physics↗

Photostability of Ambient-Processed, Conjugated Polymer Electrochromic Devices Encapsulated by Bioderived Barrier Films

Polymer-based electrochromic devices (ECDs) are a promising technology for enabling low-voltage, disposable displays, yet are currently limited by photo-oxidative bleaching of the active materials. Here, renewable barrier films composed of cellulose and chitin are presented as an alternative to poly(ethylene terephthalate) (PET) for encapsulating ECDs. To assess barrier film effectiveness, lateral ECDs composed of poly(3,4-propylenedioxythiophene-(CH 2 OEtHx) 2 ) (P(ProDOT)) active layers were constructed and encapsulated with a multilayer barrier consisting of chitin nanofibers and cellulose nanocrystals spray cast onto a cellulose acetate substrate (oxygen transmission rate (OTR) = 29 cm 3 m –2 day –1 ), a commercially available PET film (OTR = 8.5 cm 3 m –2 day –1 ), and a high-performance PET-Al 2 O 3 multilayer barrier film (OTR < 1 cm 3 m –2 day –1 ). The photodegradation of the P(ProDOT) active layer was determined by measuring the evolution of the colorimetric contrast (ΔE*) and switching speeds as a function of light exposure (100 mW cm –2 , AM 1.5 G light). Photodegradation was found to proceed at a similar rate for all encapsulated devices (roughly 10 times more slowly than unencapsulated devices), highlighting the opportunity for replacing petroleum packaging with bioderived barrier films. Analysis of the switching kinetics, the shifts in optical absorbance, and evidence of chemical degradation indicate that both photochemical breakdown of the electrolyte and cross-linking of the P(ProDOT) active material are key drivers for loss of device performance when oxygen flux to the active material is limited. Furthermore, pathways toward better understanding photodegradation are then proposed with sustainability in mind for future ECD design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Origin of Phase Separation in Ni-Rich Layered Oxide Cathode Materials During Electrochemical Cycling

In intercalation materials, the kinetics and uniformity of mass transport across the nanocrystalline domains dictate the structural reversibility and transport capability at the macroscopic level. (De)intercalation-induced interlayer disintegrations exhibit anisotropic crystallite size change. Due to the anisotropic mass transport mechanism, separated phases are inherently crystallographically oriented. One such material is LiNi $1–x–y$ Mn $x$ Co $y$ O 2 , which plays a pivotal role in advanced Li-ion batteries but suffers from severe phase inhomogeneities under fast charge or electrochemical aging. Here, using operando synchrotron techniques, we probe the mechanistic origins of the compositional and orientational-dependent phase separations during the electrochemical cycling of LiNi 0.8 Mn 0.1 Co 0.1 O 2 by comprehensive analysis of both in-plane and out-of-plane reflections. In the H2/H3 phase regime, in-plane domain propagation occurs due to increased covalency despite the severe decay of interlayer crystallographic order, resulting in the change of crystalline domain shape from 3D spheres to two-dimensional nanosheets. The crystallographically selective XRD line splitting is linked to the geometry of the facets as mass transfers along the ab plane. In conclusion, this work provides mechanistic insights into crystallographic orientation-dependent phase inhomogeneity under fast charge and extended cycling.

36 MATERIALS SCIENCE↗

Atomic structure and phase assemblages in novel M-(N)-A-S-H materials

This paper investigates the atomic structure and phase assemblages in new sodium-stabilized magnesium aluminosilicate hydrate (M-(N)-A-S-H) cementitious binders. Results indicate that in the absence of Ca{sup 2+}, Mg{sup 2+} promotes a binder atomic structure of Si-Al tetrahedral sheets and octahedral Mg sheets with hydrated Na{sup +} cations likely in the interlayer sites similar to trioctahedral micas (phyllosilicates). NMR studies verify the incorporation of Al in tetrahedral silicate sheets. XRD demonstrates the ability of these regions to nucleate and form zeolites (i.e., sodalite) as well as the formation of Mg-Al layered double hydroxide (LDH) phases (i.e., meixnerite), which is expected due to high concentrations of Mg and Al. TGA results indicate that M-(N)-A-S-H possesses chemically bound water and hydroxyl units similar to other Mg binders. These results evince the critical role of Mg to form unique atomic structures and durability-linked phases in low-calcium alkali-activated materials.

36 MATERIALS SCIENCE↗

Development of a worldwide model for Flayer-produced scintillation

An empirical approach to modeling the electron-density irregularities in the F layer of the earth's ionosphere that are primarily responsible for scintillation of transatmospheric VHF-UHF signals has been devised and tested. The work was directed toward two major goals: first, development of a worldwide model for describing the rms fluctuation in signal strength to be expected on an arbitrary satellite-to-earth communication link under average ionospheric conditions; and, second, investigation of the feasibility of similar modeling for description of the complete first-order distribution of signal strength.

Fremouw, E. J.↗

Airborne lidar and radiometric observations of PBL- and low clouds

Boundary layer- and low altitude clouds over open ocean and continent areas have been studied during several field campaigns since mid-1990 using the French airborne backscatter lidar LEANDRE in conjunction with on-board IR and visible radiometers. LEANDRE is an automatic system, and a modification of the instrumental parameters, when airborne, is computer controlled through an operator keyboard. The vertical range squared lidar signals and instrument status are displayed in real time on two dedicated monitors. The lidar is used either down- or up-looking while the aircraft is flying above or below clouds. A switching of the viewing configuration takes about a minute. The lidar measurements provide a high resolution description of cloud morphology and holes in cloud layers. The flights were conducted during various meteorological conditions on single or multilayer stratocumulus and cumulus decks. Analysis on a single shot basis of cloud top (or bottom) altitude and a plot of the corresponding histogram allows one to determine a probability density function (PDF). The preliminary results show the PDFs for cloud top are not Gaussian and symmetric about the mean value. The skewness varies with atmospheric conditions. An example of results recorded over the Atlantic ocean near Biarritz is displayed, showing: (1) the range squared lidar signals as a function of time (here 100 s corresponds to about 8 km, 60 shots are averaged on horizontal); the Planetary Boundary Layer (PBL) - up to 600 m - is observed at the beginning of the leg as well as on surface returns, giving an indication of the porosity; (2) the cloud top altitude variation between 2.4 to 2.8 km during the 150 to 320 s section; and (3) the corresponding PDF. Similar results are obtained on stratocumulus over land. Single shot measurements can be used also to determine an optical porosity at a small scale as well as a fractional cloudiness at a larger scale. A comparison of cloud top altitude retrieved from lidar and narrowbeam IR radiometer is conducted to study the scale integration problem. A good agreement within less than 100 m relies on spatial uniformity and an optically thick layer. In the presence of holes, a discrepancy is observed. This is illustrated in figure 2, displaying as a function of time (1) the lidar signals; (2) the target temperature (either clouds or sea surface) retreived from a narrowbeam IR radiometer, 17 C is the sea surface temperature on that day; and (3) the visible flux, linked to cloud albedo, measured by a pyranometer. In preparation of ASTEX, down- and up-looking measurements where conducted on stratocumulus clouds over the Atlantic Ocean near Quimper in Brittany. Depending on the flight pattern orientation with respect to the wind, the top and bottom cloud morphologies are different. Preliminary results are given on cloud morphology, cloud top PDFs, optical porosity, fractional cloudiness, and comparison of lidar and radiometric measurements.

Flamant, P. H.↗

An Application of the "Virtual Spacecraft" Concept in Evaluation of the Mars Pathfinder Lander Low Gain Antenna

The virtual spacecraft concept is embodied in a set of subsystems, either in the form of hardware or computational models, which together represent all, or a portion of, a spacecraft. For example, the telecommunications transponder may be a hardware prototype while the propulsion system may exist only as a simulation. As the various subsystems are realized in hardware, the spacecraft becomes progressively less virtual. This concept is enabled by JPL's Mission System Testbed which is a set of networked workstations running a message passing operating system called "TRAMEL" which stands for Task Remote Asynchronous Message Exchange Layer. Each simulation on the workstations, which may in fact be hardware controlled by the workstation, "publishes" its operating parameters on TRAMEL and other simulations requiring those parameters as input may "subscribe" to them. In this manner, the whole simulation operates as a single virtual system. This paper describes a simulation designed to evaluate a communications link between the earth and the Mars Pathfinder Lander module as it descends under a parachute through the Martian atmosphere toward the planet's surface. This link includes a transmitter and a low gain antenna on the spacecraft and a receiving antenna and receiver on the earth as well as a simulation of the dynamics of the spacecraft. The transmitter, the ground station antenna, the receiver and the dynamics are all simulated computationally while the spacecraft antenna is implemented in hardware on a very simple spacecraft mockup. The dynamics simulation is a record of one output of the ensemble of outputs of a Monte Carlo simulation of the descent. Additionally, the antenna/spacecraft mock-up system was simulated using APATCH, a shooting and bouncing ray code developed by Demaco, Inc. The antenna simulation, the antenna hardware, and the link simulation are all physically located in different facilities at JPL separated by several hundred meters and are linked via the local area network (LAN).

Pogorzelski, R. J.↗

The Solar-Stellar Connection (NAG5-6124: SOHO Guest Investigator Program)

The following is a final report from the SOHO Guest Investigator program to use the SUMER far-UV spectrometer to obtain imaging spectroscopy in support of the goals of the so-called "solar-stellar connection." In particular, a major emphasis was utilization of the long-slit time-resolved maps of the solar surface in bright far-UV emission lines to deduce how particular aspects of the temporally and spatially averaged line profiles trace back to individual structural features of the magnetically disturbed outer atmosphere; to help interpret the unresolved line profiles from high quality stellar observations (say, with the Space Telescope Imaging Spectrograph). The researchers served two tours of duty in the SOHO Operations Center as SUMER planners, during which time we conducted an extensive series of observing programs. These can be divided into three general categories: surface mapping, translimb spectroscopy, and active region diagnostics. We have analyzed some of the large volumes of data to the point where we have presented them in poster papers, and in invited papers at national and international meetings. Listed below are the titles of the preliminary publications we have written, including brief abstracts to indicate the main results. (1) Chromospheric structure and Dynamics-- Observations -- The chromosphere is a highly structured dynamic 'layer' of the solar outer atmosphere. Here, not only are the effects of mechanical heating first evident (moving upward in altitude from the deep photosphere), but also the amount of nonradiative energy deposited is far greater than in the albeit much hotter overlying transition region and corona. Further, the chromosphere is by far the thickest zone of the solar atmosphere with respect to the pressure scale height. A major goal of stellar astrophysics is to understand how the chromosphere is heated and why it adopts its peculiar structure. A cursory examination of solar filtergrams and high-resolution movies demonstrates that much of the chromospheric "action" must be occurring on fine spatial scales and short times; particularly in the cell interior transient brightenings, but also in the longer-lived network fragments. That regime of investigation is far removed from what one usually associates with "synoptic" measurements. Nevertheless, synoptic observations of chromospheric indices, filtergrams, and globally-averaged profile parameters not only can provide important insight concerning the crucial role of the cycle-variable part of the solar magnetic field; but they also can forge a key link with analogous measurements of the stars, where often the phenomena can be significantly exaggerated from the solar case, but high spatial resolution reconnaissance is not even a remote possibility. In addition to discussing the synoptic aspects of chromospheric structure and dynamics, I summarized new insights into the general problem of the solar chromosphere that have been obtained recently with the SUMER far-ultraviolet spectrometer on SOHO. (2) CO and the Temperature Structure of the Solar Atmosphere -- The surface layers of the Sun provide a crucial boundary condition for many of the processes that occur in the deep interior. The stratification of the outer solar atmosphere once was thought to be well understood. However, studies of thermally sensitive molecular absorptions in the infrared revealed puzzling anomalies. Strong lines of the CO fundamental vibration-rotation bands near 5 microns showed very cool temperatures at the extreme limb, and remarkable off-limb emissions extending well into the supposedly hot chromosphere. The conflicting pictures of the photosphere/chromosphere interface, from the widely separated wavelength regimes, has raised suspicions that those "layers" of the atmosphere are much more inhomogeneous than previously suspected. One proposal is that the low chromosphere is dominated by cool gas, the "COmosphere," which is threaded by a network of persistent small-scale hot magnetic filaments and occasionally disrupted by localized acoustic disturbances. The COmosphere is capped by the merged fields of the network elements in the chromospheric "canopy." (3) Translimb Spectroscopy with SOHO/SUMER -- We have used SUMER to obtain deep exposures of the 1300-1400 A spectrum, at the extreme limb and off-limb. Previous "translimb" studies in the thermal infrared had revealed remarkable extensions of cold material (T is approximately equal to 3000 K)-traced by carbon monoxide emission lines-into the heart of the hot chromosphere. A main objective of our program was to search for corresponding far-UV signatures of the "thermally-bifurcated" low chromosphere; for example, radiatively fluoresced emissions of the CO A-X 4th-positive system (collisional excitation would be negligible in cold gas). We conducted two separate observing programs with SUMER. Both made use of the 1 inch-diameter circular aperture, translated across the limb in the minimum motor step increments of 0."375, along the central meridian in the Northern polar coronal hole. The first program executed for nine hours beginning 19UT 25 Oct 1996. The full wavelength range was 1340-1400 A. It was recorded in two overlapping segments, placing key regions of the spectrum alternately on the KBr and bare parts of the detector, to help isolate 2nd-order features. Each segment was integrated for 500 s, and 32 pairs were obtained to span a 12" swath centered on the optical limb. The second program was conducted 00-09UT 01 Dec 1996. It consisted of a single wavelength setting (1300-1340 A) with exposure time 500 s, but twice the spatial coverage of the earlier series: 64 steps, for a total displacement of 24". The strong chromospheric resonance lines of atomic oxygen (1302-1305 A) and ionized carbon (1334-1335 A) were observed on the bare part of the MCP camera.

Ayres, Thomas R.↗

Optimizing Non-Terrestrial Hybrid RF/FSO Links With Reinforcement Learning: Navigating Through Clouds

In the pursuit of ubiquitous broadband connectivity, there has been a significant shift towards the vertical expansion of communication networks into space, particularly through the exploitation of low Earth orbit (LEO) satellite constellations, which are favored for their relatively low latency. However, this approach faces many challenges that need to be addressed, including atmospheric turbulence, high path loss, and dynamic cloud formations. High-altitude pseudo-satellites (HAPS) have emerged as promising relaying layers between LEO satellites and ground stations, enhancing coverage, latency, and direct terrestrial user connectivity. While radio frequency (RF) bands suffer from congestion and limited bandwidth, free space optical (FSO) communications offer higher data rates, but are susceptible to misalignment and weather-induced signal degradation. To address these challenges, a hybrid RF/FSO approach has been proposed to take advantage of both technologies by dynamic switching between RF and FSO based on propagation channel conditions. This paper introduces a reinforcement learning-based algorithm designed to optimize the trajectory of HAPS, maneuver around cloudy areas, and seamlessly switch between the RF and FSO communication modes to maximize the achievable capacity. The proposed approach aims to maximize system performance by intelligently adapting to environmental conditions and offering a promising solution for next-generation space communication networks.

actor-critic algorithm↗