Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “implosion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Effects of a Xe dopant on an Ar gas-puff implosion on Z

Two Ar gas-puff experiments, each using loads consisting of two annuli and a center jet, were recently performed on Sandia National Laboratories' Z machine. These shots had the same load except that one of them (Z2603) employed a Xe dopant of 0.8% by number in the jet, which was not present in the otherwise identical Z2605. The extensive diagnostics deployed in these experiments reveal that the presence of this small fraction of Xe had a significant effect on the emitted K-shell radiation. Use of the Xe dramatically reduced the Ar K-shell yield from 373 ± 9% to 129 ± 9% kJ. However, the total yield increased, from 1.02 ± 17% to 1.14 ± 17% MJ. Also, the K-shell power pulse for Z2603 exhibited two nearly equal peaks separated by ∼5 ns, but that of Z2605 consisted of a more conventional single peak. Analysis of time- and space resolved K-shell spectra using a detailed atomic model for Ar ions indicates that a much greater fraction of the load mass was heated to the K-shell in the non-Xe shot Z2605. Previous average-ion atomic calculations of Xe cooling rates [Post et al., At. Data Nucl. Data Tables 20, 397 (1977)] show that the radiative cooling of the small 0.8% Xe fraction is nonetheless significant compared to that of the Ar and is therefore likely responsible for the differences in the shots.

Apruzese, J. P.↗

Use of 41Ar production to measure ablator areal density in NIF beryllium implosions

For the first time, 41Ar produced by the (n,ϒ) reaction from 40Ar in the beryllium shell of a DT filled Inertial Confinement Fusion capsule has been measured. Ar is co-deposited with beryllium in the sputter deposition of the capsule shell. Combined with a measurement of the neutron yield, the radioactive 41Ar then quantifies the areal density of beryllium during the DT neutron production. The measured 1.15 ± 0.17 × 10+8 atoms of 41Ar are 2.5 times that from the best post-shot calculation, suggesting that the Ar and Be areal densities are correspondingly higher than those calculated. Possible explanations are that (1) the beryllium shell is compressed more than calculated, (2) beryllium has mixed into the cold DT ice, or more likely (3) less beryllium is ablated than calculated. Since only one DT filled beryllium capsule has been fielded at NIF, these results can be confirmed and expanded in the future.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Using multiple x-ray emission images of inertially confined implosions to identify spatial variations and estimate confinement volumes (invited)

We describe two methods to analyze multiple x-ray images of a small, self-emitting object, and we apply these methods to the stagnating hotspots in inertial confinement fusion experiments. The first method, the common integrated profile, can be employed to assess and quantify spatial variations in opacity. It is both a simple assessment of consistency and a sophisticated measurement of variations in a region that is otherwise difficult to observe. Second, we present a method to estimate volumes of highly asymmetric objects using multiple images of x-ray emission. The method is based on image intensities and does not require any explicit assumption of symmetry

47 OTHER INSTRUMENTATION↗

Theory of ignition and burn propagation in inertial fusion implosions

A detailed analytic model is presented here to investigate the physics of burn propagation in inertially confined plasmas. The onset of ignition and burn propagation occurs when alpha heating of the hot spot causes rapid ablation of shell mass into the hot spot. This allows large energy gains to be achieved since most of the fuel mass is located in the shell. Here, we first present a comprehensive review of previous analytic models that have been used to describe the physics of hot-spot evolution and ignition; we then show that a proper description of a propagating burn wave requires a comprehensive model of hot spot and shell evolution that includes proper mass conservation in the shell, fusion reactivity, and fuel depletion. The analytic theory is in good agreement with detailed radiation-hydrodynamic simulations that predict the onset of burn propagation as occurring when the yield enhancement caused by alpha heating is between 15- and 25-fold, $f_α$ ~ 1.4, where $f_α$ = alpha energy deposited/hot-spot energy at bang time, and the hot-spot burnup fraction is approximately 2%. We show that the definition of ignition is not sensitive to the alpha-particle stopping power nor asymmetries provided that the absorbed fraction of alpha particles $θ_α$ is correctly accounted for. Finally, we use the results of 2-D simulations to show that even when $θ_α$ is small and unknown (as is true in hot spots with mid modes that have significant leakage of alpha particles into the surrounding cold bubbles), one can still relate the experimentally measureable parameter $\chi^{53}_α$ to the yield amplification and the burning-plasma parameter $Q^{\text{hs}}_α$ = alpha energy deposited/total input work delivered to the hot spot

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The effect of areal density asymmetries on scattered neutron spectra in ICF implosions

Scattered neutron spectroscopy is a diagnostic technique commonly used to measure areal density in inertial confinement fusion experiments. Deleterious areal density asymmetries modify the shape of the scattered neutron spectrum. In this work, a novel analysis is developed, which can be used to fit the shape change. This will allow experimental scattered neutron spectroscopy to directly infer the amplitude and mode of the areal density asymmetries, with little sensitivity to confounding factors that affect other diagnostics for areal density. The model is tested on spectra produced by a neutron transport calculation with both isotropic and anisotropic primary fusion neutron sources. Multiple lines of sight are required to infer the areal density distribution over the whole sphere—we investigate the error propagation and optimal detector arrangement associated with the inference of mode 1 asymmetries.

Crilly, A. J. (ORCID:0000000204299332)↗

Extension of charged-particle spectrometer capabilities for diagnosing implosions on OMEGA, Z, and the NIF

New designs and a new analysis technique have been developed for an existing compact charged-particle spectrometer on the NIF and OMEGA. The new analysis technique extends the capabilities of this diagnostic to measure arbitrarily shaped ion spectra down to 1 MeV with yields as low as 10 6 . Three different designs are provided optimized for the measurement of DD protons, T 3 He deuterons, and 3 He 3 He protons. The designs are highly customizable, and a generalized framework is provided for optimizing the design for alternative applications. Additionally, the understanding of the detector’s response and uncertainties is greatly expanded upon. A new calibration procedure is also developed to increase the precision of the measurements.

47 OTHER INSTRUMENTATION↗

Emission phases of implosion sources for x-ray absorption fine structure spectroscopy

At the Laboratory for Laser Energetics' Omega Laser Facility, thin plastic shells were directly driven with ∼20 kJ resulting in a time-integrated x-ray yield of ∼1012 ph/eV/sr at 7 keV. Using temporally, spatially, and spectrally discriminating diagnostics, three x-ray emission phases were identified: corona emission produced by the laser ablation of the shell, core stagnation, and afterglow emission due to the expanding hot material after stagnation. The newly measured corona and afterglow emission phases account for ∼25% of the total x-ray signal and produce x-ray emission at a different time or larger radius than previously considered. The resulting implications of this additional emission for x-ray absorption fine structure spectroscopy are discussed. Finally, improvements to the laser drive intensity and uniformity produced a factor-of-2 increase in total x-ray emission while decreasing the size of the stagnated core.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

First measurement of the 10B(α,n)13N reaction in an inertial confinement fusion implosion at the National Ignition Facility: Initial steps toward the development of a radiochemistry mix diagnostic

We report the first measurement of the 10B(α,n)13N reaction in a polar-direct-drive exploding pusher (PDXP) at the National Ignition Facility (NIF). This work is motivated by the need to develop alternative mix diagnostics, radiochemistry being the focus here. The target is composed of a 65/35 at. % deuterium–tritium (DT) fill surrounded by a roughly 30 μm thick beryllium ablator. The inner portion of the beryllium ablator is doped with 10 at. % of 10B. Radiation-hydrodynamics calculations were performed in 1D to optimize both the remaining boron rho-R and the DT neutron yield. A charged-particle transport post-processor has been developed to study α-induced reactions on the ablator material. Results indicate a large 13N production from α-induced reactions on 10B, measurable by the radiochemical analysis of a gaseous samples system at the NIF. The PDXP target N201115-001 was successfully fielded on the NIF, and nitrogen from the 10B(α,n)13N reaction was measured. The 13N production yield, as well as the DT neutron yield, was, however, lower than expected. Some of the reduced yields can be explained by the oblate shape, but the ratios of the various radiochemical signals are not commensurate with expectations based on a simple reduction of the 1D results. Preliminary 2D radiation-hydrodynamics computations are consistent with the experimental measurements, and work is ongoing to extend the radiochemistry analysis into higher dimensions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Modeling ablator grain structure impacts in ICF implosions

High-density carbon is a leading ablator material for inertial confinement fusion (ICF). This and some other ablator materials have grain structure which is believed to introduce very small-scale (~nm) density inhomogeneity. In principle, such inhomogeneity can affect key ICF metrics like fuel compression and yield, by, for example, acting as a seed for instabilities and inducing mix between ablator and fuel. However, assessments of such effects are uncertain due to the difficulty of modeling this small-scale structure in ICF simulations, typically requiring reduced-resolution modeling that scales these features. We present a grain model and show both the impact of de-resolving grains and the complex mixing dynamics such structures can induce. We find that different methods for de-resolving grains can yield both different total deposition of kinetic energy perturbations and different fuel–ablator mixing. We then show a simple-to-implement approach for approximately conserving the deposition of perturbed kinetic energy and demonstrate that, for the present grain model and test cases, this approach yields a reasonably matched time history of mix width between less and more resolved grain models. The simulations here also demonstrate the complex interaction history between grain-induced mixing and instability around the fuel–ablator interface, showing, for example, that the grain-induced perturbations typically trigger instability of conduction-driven density gradients in the DT fuel, enhancing mix penetration early in the acceleration of the shell. Furthermore simulating both microscale and nanoscale grains, we find initial evidence for larger mixing in the microscale case of the present model, despite smaller deposited kinetic energy perturbation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Neutron imaging of inertial confinement fusion implosions

We review experimental neutron imaging of inertial confinement fusion sources, including the neutron imaging systems that have been used in our measurements at the National Ignition Facility. These systems allow measurements with 10 µm resolution for fusion deuterium–deuterium and deuterium–tritium neutron sources with mean radius up to 400 µm, including measurements of neutrons scattered to lower energy in the remaining cold fuel. These measurements are critical for understanding the fusion burn volume and the three-dimensional effects that can reduce the neutron yields.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

First bromine doped cryogenic implosion at the National Ignition Facility

We report on the first experiment dedicated to the study of nuclear reactions on dopants in a cryogenic capsule at the National Ignition Facility (NIF). This was accomplished using bromine doping in the inner layers of the CH ablator of a capsule identical to that used in the NIF shot N140520. The capsule was doped with 3 × 1016 bromine atoms. The doped capsule shot, N170730, resulted in a DT yield that was 2.6 times lower than the undoped equivalent. The Radiochemical Analysis of Gaseous Samples (RAGS) system was used to collect and detect 79Kr atoms resulting from energetic deuteron and proton ion reactions on 79Br. RAGS was also used to detect 13N produced dominantly by knock-on deuteron reactions on the 12C in the ablator. High-energy reaction-in-flight neutrons were detected via the 209Bi(n,4n)206Bi reaction, using bismuth activation foils located 50 cm outside of the target capsule. The robustness of the RAGS signals suggests that the use of nuclear reactions on dopants as diagnostics is quite feasible.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

High-magnification Faraday rotation imaging and analysis of X-pinch implosion dynamics

An X-pinch load driven by an intense current pulse (>100 kA in ~100 ns) can result in the formation of a small radius, runaway compressional micro-pinch. A micro-pinch is characterized by a hot (>1 keV), current-driven (>100 kA), high-density plasma column (near solid density) with a small neck diameter (1–10 µm), a short axial extent (<1 mm), and a short duration (≲1 ns). With material pressures often well into the multi-Mbar regime, a micro-pinch plasma often radiates an intense, sub-ns burst of sub-keV to multi-keV x rays. A low-density coronal plasma immediately surrounding the dense plasma neck could potentially shunt current away from the neck and thus reduce the magnetic drive pressure applied to the neck. Here, to study the current distribution in the coronal plasma, a Faraday rotation imaging diagnostic (1064 nm) capable of producing simultaneous high-magnification polarimetric and interferometric images has been developed for the MAIZE facility at the University of Michigan. Designed with a variable magnification (1–10×), this diagnostic achieves a spatial resolution of ~35 µm, which is useful for resolving the ~100-μm-scale coronal plasma immediately surrounding the dense core. This system has now been used on a reduced-output MAIZE (100–200 kA, 150 ns) to assess the radial distribution of drive current immediately surrounding the dense micro-pinch neck. The total current enclosed was found to increase as a function of radius, r, from a value of ≈ 50 ± 25 kA at r ≈ 140 µm (at the edge of the dense neck) to a maximal value of ≈150 ± 75 kA for r ≥ 225 µm. This corresponds to a peak magnetic drive pressure of ≈75 ± 50 kbar at r ≈ 225 µm. The limitations of these measurements are discussed in the paper.

47 OTHER INSTRUMENTATION↗