Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Radiation Hardened, Modulator ASIC for High Data Rate Communications

Satellite-based telecommunication services are challenged by the need to generate down-link power levels adequate to support high quality (BER approx. equals 10(exp 12)) links required for modem broadband data services. Bandwidth-efficient Nyquist signaling, using low values of excess bandwidth (alpha), can exhibit large peak-to-average-power ratio (PAPR) values. High PAPR values necessitate high-power amplifier (HPA) backoff greater than the PAPR, resulting in unacceptably low HPA efficiency. Given the high cost of on-board prime power, this inefficiency represents both an economical burden, and a constraint on the rates and quality of data services supportable from satellite platforms. Constant-envelope signals offer improved power-efficiency, but only by imposing a severe bandwidth-efficiency penalty. This paper describes a radiation- hardened modulator which can improve satellite-based broadband data services by combining the bandwidth-efficiency of low-alpha Nyquist signals with high power-efficiency (negligible HPA backoff).

McCallister, Ron↗
NASA NTRS1983

Calibration of the aerodynamic coefficient identification package measurements from the shuttle entry flights using inertial measurement unit data

The Aerodynamic Coefficient Identification Package (ACIP) is an instrument consisting of body mounted linear accelerometers, rate gyros, and angular accelerometers for measuring the Space Shuttle vehicular dynamics. The high rate recorded data are utilized for postflight aerodynamic coefficient extraction studies. Although consistent with pre-mission accuracies specified by the manufacturer, the ACIP data were found to contain detectable levels of systematic error, primarily bias, as well as scale factor, static misalignment, and temperature dependent errors. This paper summarizes the technique whereby the systematic ACIP error sources were detected, identified, and calibrated with the use of recorded dynamic data from the low rate, highly accurate Inertial Measurement Units.

Heck, M. L.↗
NASA NTRS1983

An Attached Payload Operations Center (APOC) at the Goddard Space Flight Center (GSFC), volume 2

An overview of the APOC is given. For Spacelab payloads channel 2 and 3 data are input via a Statistical Multiplexer (SM) to the various SIPS functions. These include recording of the data on High Density Recorders (HDR), DQM and demultiplexing of the composite data stream by the High Rate Demultiplexer (HRDM). This system performs the inverse functions of the onboard Spacelab High Rate Multiplexer (HRM) enabling access to the data streams as multiplexed onboard the Spacelab. The contents and characteristics of channels one, two and three data as downlinked by the Tracking and Data Relay Satellite System (TDRSS) ku-band are given.

Source record↗
DOE OSTI2023

Rapid Fabrication of High Frame Rate Multichannel FTIR Spectrometers

Spectrally resolved signals in the short- to mid-wave infrared (SWIR/MWIR) bands at high-temporal resolution are critical for many national security remote sensing missions. Currently available off the shelf technology can achieve either high temporal resolution or high spectral resolution, but rugged instruments that can achieve both simultaneously remain mostly in the realm of one-off R&D projects. This report documents efforts to demonstrate a new technique for designing and building high resolution, high framerate multichannel FTIR (MC-FTIR) spectrometers that operate in the SWIR/MWIR bands. The core optical element in a MC-FTIR spectrometer is an array of statically-tuned lamellar grating interferometers (LGI). In the original MC-FTIR work these arrays were fabricated using a synchrotron x-ray lithography method. We proposed to instead fabricate these LGI arrays using multiphoton lithography (MPL), a 3D printing technique that can fabricate meso-scale structures with sub-micron precision. Although we were able to fabricate LGI arrays of sufficient size using MPL, the realized optical surfaces had unsuitably high optical form errors, precluding their use in a fieldable instrument. Further advancement in MPL technology may eventually enable fabrication of interferometer-grade LGI arrays.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Design and Production for Maximum Structural Efficiency With Respect to Fiber Orientation With Increased Understanding of Hybrid Fiber Flow Behavior

Discontinuous fiber-reinforced thermoplastic composites have gained considerable attention in automotive, aerospace, and other industries, due to their high-rate of production combined with their ability to attain complex and intricate shapes. Among other high-rate thermoplastic manufacturing processes, injection-molding is one of the most common manufacturing methods due to fast production and high surface finishing of complex geometries. Fiber orientation in discontinuous fiber composites plays a pivotal role in determining the mechanical, electrical, and thermomechanical properties, underscoring the necessity to comprehend fiber orientation in injection molded parts. Among different fiber types, glass and carbon fibers are most common in the composite industries. The recent trend of hybrid composites comprising both glass fiber (GF) and carbon fiber (CF) is also gaining importance in the automotive industry. Hybrid fiber options allow designers to optimize the balance between glass and carbon fibers by leveraging the high durability and low cost of GF while the strength and lightweight properties of CF. Consequently, comparing the fiber oriented distribution (FOD) of injection molded composites containing GF, CF, and a hybrid of GF/CF is critical to investigating the local mechanical properties of intricate structures for high-end applications. In Phase I of this project, FOD in injection-molded panels with respect to distance from the gate was analyzed using X-ray computed tomography (X-CT) for GF, CF, and hybrid CF/GF (CGF) reinforced nylon 66. To understand the reason behind the FOD with different fiber types, computational fluid dynamics (CFD) and rheology were performed. Samples were extracted at three locations: near the gate, center, and opposite end. Thickness of the layers of typical skin-shell-core type FOD varies with fiber type and location. GF achieved flow direction alignment (in shell) earlier than viscous CF and CGF near the gate, whereas CF showed the highest flow-direction alignment at the center due to shear induced orientation. At the opposite end, GF experienced more backflow than others indicating faster mold filling owing to its lower viscosity. Hybrid CGF exhibited GF-dominated center and CF-dominated end region. The numerical model used to obtain FOD and rheological predictions for the CF and GF composites served to corroborate the trends observed in the experimental trials. The FOD responses across fiber types and location were reflected in their longitudinal and transverse properties. Only GF showed higher longitudinal modulus over transverse modulus near the gate attributed to rapid alignment, whereas CF and CGF exhibited opposite trend. However, fountain flow enhanced the longitudinal modulus over transverse modulus with the distance for all, particularly for CF. This study offers insights into mold filling behavior of different fibers which are critical in optimizing injection molding conditions for tailored final properties.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Dates and rates of loess deposition and soil formation on the Snake River Plain, Idaho, USA

Loess-paleosol sequences in eolian deposits on the Snake River Plain, Idaho, western United States, preserve records of late Pleistocene to Holocene glacial-interglacial cycles. Here, we examine climate-driven changes in the timing and rate of loess accretion, soil formation, and pedogenic carbonate accumulation in the eastern and central Snake River Plain. High rates of loess deposition often correspond with dry, cold, and windy conditions and/or high sediment supply, while soil formation indicates landscape stability. Optically stimulated luminescence dating of four loess-soil sequences provides a record of the timing of loess deposition, and radiocarbon dating ( 14 C) of soil inorganic carbon provides ages for soil formation and pedogenic carbonate precipitation. On the central Snake River Plain, marine isotope stage (MIS) 3 is marked by loess deposition between ca. 50 ka and 33 ka, and pedogenic carbonate accumulation between ca. 42 ka calibrated years before present (cal. B.P.) and 31 ka cal. B.P. During MIS 2, loess deposition between ca. 21 ka and 15 ka is contemporaneous with pedogenic carbonate precipitation. MIS 2 is characterized by diffuse pedogenic carbonate formation and rapid loess accumulation. Both the eastern and central Snake River Plain study sites experienced high rates of loess deposition during MIS 2; however, the eastern Snake River Plain had almost three times faster rates of loess accumulation (0.56−0.63 m/k.y. from ca. 25 ka to 17 ka) as compared to the central Snake River Plain (0.18−0.26 m/k.y. from ca. 21 ka to 15 ka). During MIS 1, loess deposition on the central Snake River Plain ca. 11 ka was coincident with pedogenic carbonate formation ca. 10 ka cal. B.P. MIS 3 and MIS 1 are characterized by A horizons and well-developed Bk horizons, indicating soil stability and lower rates of loess accumulation during these intervals. Finally, this study highlights the role of late Quaternary−scale climatic variability on rates and amounts of soil inorganic carbon storage.

Geosciences↗
NASA NTRS1973

Attitude control of a large flexible spacecraft using three-axis mass expulsion control.

A study of the elastic effects of large area solar arrays on attitude control of a spacecraft was conducted. It is demonstrated for sufficiently low structural frequencies that excitation of certain modes can induce instability in the pitch axis. Stiffening the arrays can eliminate the instability. However, a severe weight penalty is associated with such modification. A more efficient means of minimizing the structural interaction effects is to change the shape of the array. For stable configurations, another problem may be encountered. This is the imposition of high rates on the spacecraft bus by oscillation of the solar arrays. Since low rates are required to obtain accurate science experiment results, it is imperative that the high rate problem be resolved. This also is possible by changing the solar array configuration.

Marsh, E. L.↗
DOE OSTI2023

Revealing the Electrochemical Kinetics of Electrolytes in Nanosized LiFePO 4 Electrodes

Lithium-ion battery rate performance is ultimately limited by the electrolyte, yet the behaviors of electrolytes during high-rate (dis)charge remain elusive to electrochemical measurement. Herein, we develop and study a nanosized LiFePO 4 model system in which the electrolyte completely controls the electrochemical kinetics of the porous electrode. Impedance spectroscopy, cyclic voltammetry, and rate performance testing prove that ion transport in the electrolyte is the sole rate-limiting process, even in thin electrodes. A novel pseudo-steady-state extrapolation (S3E) method for Tafel analysis shows that LiFePO 4 obeys Butler-Volmer kinetics with a transfer coefficient of 3. The combination of these unexpectedly rapid interfacial kinetics and an activation barrier for phase transformation causes extreme reaction heterogeneity, which manifests as a moving reaction zone. Resistance versus capacity analysis enables direct measurement of electrolyte resistance growth during high-rate (dis)charge, revealing how the interaction between concentration polarization and a moving reaction zone controls electrolyte rate performance in LiFePO 4 electrodes. This work elucidates the profound impacts of the electrolyte on electrochemical measurements in porous battery electrodes: when the active material is not rate limiting, it is impossible to directly measure the intrinsic kinetics of the active material, but conversely, it becomes possible to directly measure the kinetics of the electrolyte.

Electrochemistry↗
DOE OSTI2020

High-Power Lithium Metal Batteries Enabled by High-Concentration Acetonitrile-Based Electrolytes with Vinylene Carbonate Additive

To enable next-generation high power, high-energy-density lithium (Li) metal batteries (LMBs), an electrolyte possessing both high Li Coulombic efficiency (CE) at high-rate and good anodic stability on cathodes is critical. Acetonitrile (AN) is a well-known organic solvent for high anodic stability and high ionic conductivity, yet its application in LMBs is limited due to its poor compatibility with Li metal anode even at high salt concentration conditions. Here, we developed a highly concentrated AN-based electrolyte with vinylene carbonate (VC) additive to suppress Li+ depletion at high current densities. Addition of VC in the AN-based electrolyte leads to the formation of a polycarbonate-based solid electrolyte interphase which minimizes Li corrosion and leads to very high Li CE of up to 99.1% at a current density of 0.2 mA cm-2. Using such an electrolyte, fast charging of Li||NMC333 cells has been realized at a high current density of 3.6 mA cm-2, and stable cycling of Li||NMC622 cells with a high cathode loading of 4 mAh cm-2 has also been demonstrated.

Peng, Zhe↗
NASA NTRS1972

Fuel droplet burning rates at high pressures

Combustion of methanol, ethanol, propanol -1, n - pentane, n - heptane and n - decane was observed in air under natural convection conditions at pressures up to 100 atm. The droplets were simulated by porous spheres with diameters in the range 0.63 - 1.90 cm. The pressure levels of the tests were high enough so that near critical combustion was observed for methanol and ethanol. Measurements were made of the burning rate and liquid surface temperatures of the fuels. The data were compared with variable property analysis of the combustion process, including a correction for natural convection. The burning rate predictions of the various theories were similar and in fair agreement with the data. The high pressure theory gave the best prediction for the liquid surface temperatures of ethanol and propanol -1 at high pressure. The experiments indicated the approach of critical burning conditions for methanol and ethanol at pressures on the order of 80 - 100 atm, which was in good agreement with the predictions of both the low and high pressure analysis.

Canada, G. S.↗
DOE OSTI2022

High strain rate deformation of aged TRIP Ti-10V-2Fe-3Al (wt.%) examined by in-situ synchrotron X-ray diffraction

Transformation Induced Plasticity (TRIP) is a promising avenue for tailoring the work hardening response of metastable $β$ titanium (Ti) alloys. Here we show that aged TRIP Ti-10V-2Fe-3Al (wt.%) maintains higher elongations and flow stresses as strain rate increases, if phase stability and microstructural characteristics are tuned. Low temperature aging influences the matrix $β$ phase stability by $ω$ phase precipitation, which affords a promising way to impact the TRIP effect and obtain desirable mechanical properties, ranging from high damping capacity to good strength/ductility combinations. Although TRIP is active during quasi-static and dynamic testing up to 2000 s –1 , increasing aging time and/or strain rate reduces the overall propensity for the TRIP effect and extent of transformation, which occurs rapidly just at the onset of yielding. Importantly, TRIP with $ω$ phase precipitation provides interesting alloying, microstructure, and property design strategies for engineering applications like lightweight protective structures, where high strains and the need for energy absorption are encountered.

36 MATERIALS SCIENCE↗
NASA NTRS1991

A high data rate recorder for astronomy

A magnetic tape recorder developed for the special requirements of radio astronomy and geodesy is described. These requirements include a high bit packing density and long record times. The current version of this longitudinal recorder used by the Very Long Baseline Array (VLBA) records 5.5 Terabits on a 14-in diameter reel of inch-wide tape. A maximum record rate of 256 Mb/s is achieved in the VLBA configuration with one recorder operating at 4 ms and utilizing 32 of the heads in a single stack. The VLBA recorders have been tested using a longitudinal density of 2.25 fr/micron; 448 data + 56 system tracks are recorded in 14 passes, each lasting 50 min, for a total record time (at 128 Mb/s) of 12 h on 14-in diameter reel of inch-wide 13-microns-thick D1-equivalent tape.

Hinteregger, H. F.↗
NASA NTRS2019

Experimental Methods in Materials for Structural Impact Dynamics

Over the past two decades significant technological advances have completely changed the way in which experimental testing is conducted in Structural Impact Dynamics applications. Probably the two most significant advances have been the advent of high speed digital video cameras and the use of Digital Image Correlation techniques to measure deformations and strains at high rates. These advances have led to significantly more accurate measurements of material and structural response under high rate loading, which has also led to advances in computational modeling techniques for Impact Dynamics. In this address we will review the past, present and what the future may hold for experimental methods in the field of Structural Impact Dynamics.

Structural Impact Dynamics↗
DOE OSTI2023

High Dose Rate Irradiations of Enduray Vision System for Nuclear Inspections

Higher radiation-hardened video cameras are needed in the operation and remote handling of equipment in nuclear reactor inspection and refueling applications. Vega Wave Systems, Inc. has developed a radiation-hardened vision system for nuclear energy applications. This vision system has been developed under several small business innovative research programs (SBIRs) from the U.S. Department of Energy, and the previous GAIN voucher program at Argonne National Laboratory (ANL) was successful in demonstrating that a prototype of the camera is radiation-hard up to at least 525 kGy (5.25 × 106 rad, Si equivalent) at dose rates of 10 kGy/hr with no measurable degradation in image quality and no measurable radiation-induced noise (RIN). Vega Wave Systems has developed a new version of the camera with more than 3X the resolution using a new design and new components, and this new design requires radiation-hardness qualification for marketplace acceptance. The program described in this report provided high radiation-hardness testing of this redesigned high-resolution vision system using the Argonne Low-Energy Accelerator Facility (LEAF). This report presents the results of irradiation tests performed on Vega Wave System’s redesigned high resolution vision system at a dose rate of 9.3 kGy/hr and up to total doses of 1823 kGy. This was an accumulation of 197 hours of irradiation. The results were excellent, providing proof of the redesigned high-resolution vision system’s immunity to high levels of radiation.

42 ENGINEERING↗
NASA NTRS1973

High data rate optical transceiver terminal

The objectives of this study were: (1) to design a 400 Mbps optical transceiver terminal to operate from a high-altitude balloon-borne platform in order to permit the quantitative evaluation of a space-qualifiable optical communications system design, (2) to design an atmospheric propagation experiment to operate in conjunction with the terminal to measure the degrading effects of the atmosphere on the links, and (3) to design typical optical communications experiments for space-borne laboratories in the 1980-1990 time frame. As a result of the study, a transceiver package has been configured for demonstration flights during late 1974. The transceiver contains a 400 Mbps transmitter, a 400 Mbps receiver, and acquisition and tracking receivers. The transmitter is a Nd:YAG, 200 Mhz, mode-locked, CW, diode-pumped laser operating at 1.06 um requiring 50 mW for 6 db margin. It will be designed to implement Pulse Quaternary Modulation (PQM). The 400 Mbps receiver utilizes a Dynamic Crossed-Field Photomultiplier (DCFP) detector. The acquisition receiver is a Quadrant Photomultiplier Tube (QPMT) and receives a 400 Mbps signal chopped at 0.1 Mhz.

Clarke, E. S.↗
NASA NTRS1994

Hetrodyne Laser Tracking at High Doppler Rates

In hetrodyne laser tracking of a spacecraft, the incoming laser signal may be significantly offset from the local laser reference, producing a high-frequency beat note that must be accurately counted to produce an accurate phase measurement.

hetrodyne laser tracking↗
NASA NTRS1973

Fuel droplet burning rates at high pressures.

Combustion of methanol, ethanol, propanol-1, n-pentane, n-heptane, and n-decane was observed in air under natural convection conditions, at pressures up to 100 atm. The droplets were simulated by porous spheres, with diameters in the range from 0.63 to 1.90 cm. The pressure levels of the tests were high enough so that near-critical combustion was observed for methanol and ethanol. Due to the high pressures, the phase-equilibrium models of the analysis included both the conventional low-pressure approach as well as high-pressure versions, allowing for real gas effects and the solubility of combustion-product gases in the liquid phase. The burning-rate predictions of the various theories were similar, and in fair agreement with the data. The high-pressure theory gave the best prediction for the liquid-surface temperatures of ethanol and propanol-1 at high pressure. The experiments indicated the approach of critical burning conditions for methanol and ethanol at pressures on the order of 80 to 100 atm, which was in good agreement with the predictions of both the low- and high-pressure analysis.

Canada, G. S.↗