Results for “high modulus” — Page 33

NASA NTRS1999

Consequences of Atomic Oxygen Interaction With Silicone and Silicone Contamination on Surfaces in Low Earth Orbit

The exposure of silicones to atomic oxygen in low Earth orbit causes oxidation of the surface, resulting in conversion of silicone to silica. This chemical conversion increases the elastic modulus of the surface and initiates the development of a tensile strain. Ultimately, with sufficient exposure, tensile strain leads to cracking of the surface enabling the underlying unexposed silicone to be converted to silica resulting in additional depth and extent of cracking. The use of silicone coatings for the protection of materials from atomic oxygen attack is limited because of the eventual exposure of underlying unprotected polymeric material due to deep tensile stress cracking of the oxidized silicone. The use of moderate to high volatility silicones in low Earth orbit has resulted in a silicone contamination arrival at surfaces which are simultaneously being bombarded with atomic oxygen, thus leading to conversion of the silicone contaminant to silica. As a result of these processes, a gradual accumulation of contamination occurs leading to deposits which at times have been up to several microns thick (as in the case of a Mir solar array after 10 years in space). The contamination species typically consist of silicon, oxygen and carbon. which in the synergistic environment of atomic oxygen and UV radiation leads to increased solar absorptance and reduced solar transmittance. A comparison of the results of atomic oxygen interaction with silicones and silicone contamination will be presented based on the LDEF, EOIM-111, Offeq-3 spacecraft and Mir solar array in-space results. The design of a contamination pin-hole camera space experiment which uses atomic oxygen to produce an image of the sources of silicone contamination will also be presented.

Banks, Bruce A.↗

NASA NTRS1983

Development of tough, strong, iron-base alloy for cryogenic applications

The development of an iron-base alloy that combines the normally divergent properties of high toughness and high strength at cryogenic temperatures is discussed. Specifically, alloy properties were sought which at -196 C would exhibit a fracture toughness of 220 MPa-m(1/2) with a corresponding yield strength of 1.4 GPa (200 ksi). Early work showed that high toughness could be achieved in Fe-12Ni alloys containing reactive metal additions such as Al, Nb, Ti, and V. Further research emphasized strengthening of these tough alloys by thermomechanical processing and the addition of Cu. Results showed that high strength and high toughness could be achieved in a single alloy at temperatures as low as -196 C. An alloy with composition Fe-12Ni-9.5Al-2Cu exhibited a yield strength of 1.65 GPa with a corresponding fracture toughness of 220 MPa-m(1/2) at -196 C. Strengthening due to Cu additions to the Fe-12Ni base alloys results primarily from precipitation of Cu-rich epsilon particles approximately 20 nm in diameter. Strengthening mechanisms are discussed in terms of an elastic modulus hardening model and are supported by transimission electron microscopy examinations of selected test specimens.

Stephens, J. R.↗

NASA NTRS1989

Determinations of molecular weight and molecular weight distribution of high polymers by the rheological properties

Several methods are reviewed by which the molecular weight (MW) and the molecular weight distribution (MWD) of polymeric material were determined from the rheological properties. A poly(arylene ether) polymer with six different molecular weights was used in this investigation. Experimentally measured MW and MWD were conducted by GPC/LALLS (gel permeation chromatography/low angle laser light scattering), and the rheological properties of the melts were measured by a Rheometric System Four rheometer. It was found that qualitative information of the MW and MWD of these polymers could be derived from the viscoelastic properties, with the methods proposed by Zeichner and Patel, and by Dormier et al., by shifting the master curves of the dynamic storage modulus, G', and the loss modulus, G'', along the frequency axis. Efforts were also made to calculate quantitative profiles of MW and MWD for these polymers from their rheological properties. The technique recently proposed by Wu was evaluated. It was found that satisfactory results could only be obtained for polymers with single modal distribution in the molecular weight.

Huang, J. Y.↗

NASA NTRS2006

A Novel Concept for a Deformable Membrane Mirror for Correction of Large Amplitude Aberrations

Very large, light weight mirrors are being developed for applications in space. Due to launch mass and volume restrictions these mirrors will need to be much more flexible than traditional optics. The use of primary mirrors with these characteristics will lead to requirements for adaptive optics capable of correcting wave front errors with large amplitude relatively low spatial frequency aberrations. The use of low modulus membrane mirrors actuated with electrostatic attraction forces is a potential solution for this application. Several different electrostatic membrane mirrors are now available commercially. However, as the dynamic range requirement of the adaptive mirror is increased the separation distance between the membrane and the electrodes must increase to accommodate the required face sheet deformations. The actuation force applied to the mirror decreases inversely proportional to the square of the separation distance; thus for large dynamic ranges the voltage requirement can rapidly increase into the high voltage regime. Experimentation with mirrors operating in the KV range has shown that at the higher voltages a serious problem with electrostatic field cross coupling between actuators can occur. Voltage changes on individual actuators affect the voltage of other actuators making the system very difficult to control. A novel solution has been proposed that combines high voltage electrodes with mechanical actuation to overcome this problem. In this design an array of electrodes are mounted to a backing structure via light weight large dynamic range flextensional actuators. With this design the control input becomes the separation distance between the electrode and the mirror. The voltage on each of the actuators is set to a uniform relatively high voltage, thus the problem of cross talk between actuators is avoided and the favorable distributed load characteristic of electrostatic actuation is retained. Initial testing and modeling of this concept demonstrates that this is an attractive concept for increasing the dynamic range capability of electrostatic deformable mirrors.

Moore, Jim↗

NASA NTRS2018

Polyurethane Microparticles for Stimuli Response and Reduced Oxidative Degradation in Highly Porous Shape Memory Polymers

Shape memory polymers (SMPs) have been found to be promising biomaterials for a variety of medical applications; however, the clinical translation of such technology is dependent on tailorable properties such as gravimetric changes in degradation environments. For SMPs synthesized from amino-alcohols, oxidation resulting in rapid mass loss may be problematic in terms of loss of material functionality as well as toxicity and cytocompatibility concerns. Control of gravimetric changes was achieved through the incorporation of small molecule antioxidants, either directly into the polymer matrix or included in microparticles to form a SMP composite material. Direct incorporation of small molecule antioxidants, such as phenolic alcohols, was found to alter shape memory attributes and increase elastic modulus at the expense of the strain to failure. Such changes could not ensure retention of the antioxidants and therefore did not increase oxidative stability. However, the inclusion of antioxidants in microparticles was found to produce materials with similar thermomechanical and shape memory properties while increasing oxidative resistance compared to controls. The microparticle composite SMPs also act as a platform for environmental sensing, such as pH-dependent fluorescence shifts and payload release, as demonstrated by fluorescent dyes and the release of antioxidants. The use of polyurethane-urea microparticles in porous SMPs is demonstrated to increase biostability of the materials, by approximately 25%, and ultimately extend their lifespan for use in aneurysm occlusion as determined through calculated in vivo degradation rates corresponding to a porcine aneurysm environment.

Weems, A. C.↗

NASA NTRS2009

Thermodynamic Approach to Enhanced Dispersion and Physical Properties in a Carbon Nanotube/Polypeptide Nanocomposite

A high molecular weight synthetic polypeptide has been designed which exhibits favorable interactions with single wall carbon nanotubes (SWCNTs). The enthalpic and entropic penalties of mixing between these two molecules are reduced due to the polypeptide's aromatic sidechains and helical secondary structure, respectively. These enhanced interactions result in a well dispersed SWCNT/Poly (L-Leucine-ran-L-Phenylalanine) nanocomposite with enhanced mechanical and electrical properties using only shear mixing and sonication. At 0.5 wt% loading of SWCNT filler, the nanocomposite exhibits simultaneous increases in the Young's modulus, failure strain, and toughness of 8%, 120%, and 144%, respectively. At one kHz, the same nanotube loading level also enhances the dielectric constant from 2.95 to 22.81, while increasing the conductivity by four orders of magnitude.

Lovell, Conrad S.↗

NASA NTRS1980

Dynamic Modulus and Damping of Boron, Silicon Carbide, and Alumina Fibers

The dynamic modulus and damping capacity for boron, silicon carbide, and silicon carbide coated boron fibers were measured from-190 to 800 C. The single fiber vibration test also allowed measurement of transverse thermal conductivity for the silicon carbide fibers. Temperature dependent damping capacity data for alumina fibers were calculated from axial damping results for alumina-aluminum composites. The dynamics fiber data indicate essentially elastic behavior for both the silicon carbide and alumina fibers. In contrast, the boron based fibers are strongly anelastic, displaying frequency dependent moduli and very high microstructural damping. Ths single fiber damping results were compared with composite damping data in order to investigate the practical and basic effects of employing the four fiber types as reinforcement for aluminum and titanium matrices.

Dicarlo, J. A.↗

NASA NTRS1994

Ionized gas and planetary nebulae in the bulge of the blue S0 galaxy NGC 5102

We present the results of an investigation into the morphology and dynamics of ionized gas in the bulge of the gas-rich S0 galaxy NGC 5102. We show that the bulge of NGC 5102 contains a ring of ionized gas, approximately 1.3 kpc in diameter, which is centered well away from the nucleus. Through spectroscopy and (O III) lambda-5007 imaging, we show that the gas is excited by a low-velocity shock, which varies from approximately 50 to approximately 70 km/s along the ring. Fabry-Perot images in H-alpha confirm that the gas is moving slowly, and suggest that the structure is a supershell, approximately 10(exp 7) yr old. This age is significantly younger than the galaxy's nuclear starburst, which is approximately 2 x 10(exp 8) yr old. We also use our (O III) lambda-5007 images to identify planetary nebulae (PNs) in the bulge and inner disk of NGC 5102. Using the planetary nebula luminosity function, we derive a distance modulus to the galaxy of (m - M)(sub 0) = 27.47(sup +0.18)(sub -0.27), or 3.1(sup +0.3)(sub -0.4) Mpc, confirming its membership in the NGC 5128 group. Our derived value of 47.2(sup +12.2)(sub -9.2) x 10(exp -9) for the bolometric luminosity-specific PN density, alpha(sub 2.5), is higher than that observed for the bulge of M31 or the giant ellipticals of the Virgo Cluster, but not significantly different from that found for the small, normal ellipticals NGC 3377 or M32. The high value for alpha(sub 2.5) suggests that virtually all of NGC 5102's stars will someday evolve through the planetary nebula stage.

Mcmillan, Russet↗

NASA NTRS2011

Edgewise Compression Testing of STIPS-0 (Structurally Integrated Thermal Protection System)

The Structurally Integrated Thermal Protection System (SITPS) task was initiated by the NASA Hypersonics Project under the Fundamental Aeronautics Program to develop a structural load-carrying thermal protection system for use in aerospace applications. The initial NASA concept for SITPS consists of high-temperature composite facesheets (outer and inner mold lines) with a light-weight insulated structural core. An edgewise compression test was performed on the SITPS-0 test article at room temperature using conventional instrumentation and methods in order to obtain panel-level mechanical properties and behavior of the panel. Three compression loadings (10, 20 and 37 kips) were applied to the SITPS-0 panel. The panel behavior was monitored using standard techniques and non-destructive evaluation methods such as photogrammetry and acoustic emission. The elastic modulus of the SITPS-0 panel was determined to be 1.146x106 psi with a proportional limit at 1039 psi. Barrel-shaped bending of the panel and partial delamination of the IML occurred under the final loading.

Brewer, Amy R.↗

NASA NTRS2016

Failure Analysis and Recovery of a 50mm Highly Elastic Intermetallic NiTi Ball Bearing for an ISS Application

The ISS Distillation Assembly centrifuge is the pathfinder application for 50mm bore, deep-groove ball bearings made from the highly elastic intermetallic material 60NiTi. Superior corrosion and shock resistance are required to withstand the acidic wastewater exposure and heavy spacecraft launch related loads that challenge conventional steel bearings. During early ground testing one bearing unexpectedly and catastrophically failed after operating for only 200 hours of run time. A second bearing running on the same shaft was completely unaffected. A thorough investigation into the root cause of the failure determined that an excessively tight press-fit of the bearing outer race coupled with NiTis relatively low elastic modulus were key contributing factors. The proposed failure mode was successfully duplicated by experiment. To further corroborate the root cause theory, a successful bearing life test using improved installation practices (selective fitting) was conducted. The results show that NiTi bearings are suitable for space applications provided that care is taken to accommodate their unique material characteristics.

intermetallics↗

NASA NTRS2016

Failure Analysis and Recovery of a 50 MM Highly Elastic Intermetallic NiTi Ball Bearing for an ISS Application

The ISS Distillation Assembly centrifuge is the pathfinder application for 50mm bore, deep-groove ball bearings made from the highly elastic intermetallic material 60NiTi. Superior corrosion and shock resistance are required to withstand the acidic wastewater exposure and heavy spacecraft launch related loads that challenge conventional steel bearings. During early ground testing one bearing unexpectedly and catastrophically failed after operating for only 200 hours of run time. A second bearing running on the same shaft was completely unaffected. A thorough investigation into the root cause of the failure determined that an excessively tight press-fit of the bearing outer race coupled with NiTis relatively low elastic modulus were key contributing factors. The proposed failure mode was successfully duplicated by experiment. To further corroborate the root cause theory, a successful bearing life test using improved installation practices (selective fitting) was conducted. The results show that NiTi bearings are suitable for space applications provided that care is taken to accommodate their unique material characteristics.

failure analyses↗

NASA NTRS2019

Analyses and Methods of Solid Rocket Motor Material Irradiation at Marshall Space Flight Center

The search for life on other worlds is among humanity’s greatest endeavors. Europa represents the most probable location to discover extraterrestrial life in our solar system, owing to its surface composition of ice covering a liquid water ocean, warmed by the tidal forces of its orbit around Jupiter. Unfortunately, the Jovian system hosts the most intense planetary radiation environment in the solar system due to the charged particles, namely electrons and protons, trapped by Jupiter’s immense magnetic field. Any mission that attempts to approach or land on Europa must survive this radiation environment [Hand et al, 2017]. Radiation effects were identified as a priority risk to the successful development of a de-orbit stage and solid rocket motor (SRM) early in the Europa Lander De-orbit Stage project concept. The effects of primary concern tend to occur very near the outer surface of the SRM. The charged particles deposit their energy quickly and are mostly stopped in the outer metallic case, but a significant portion of radiation penetrates through the bondline and outer propellant regions. High doses of ionizing radiation are known to cause significant changes to mechanical properties of many materials, especially polymers. For polymers such as the rubber-like materials (elastomers) in a solid rocket motor, the primary damage mechanism is known as cross-linking, in which ionization causes the restructuring of the matrix of long polymer chains. Ionization energy breaks the long polymer chains and allows formation of new cross-linked bonding sites. This hardens and often strengthens the polymer, but at the cost of decreased flexibility (or modulus). Propellant, insulation, liner, and pyrotechnic materials were identified as higher risk items, and so were irradiated at Marshall Space Flight Center (MSFC) for investigation of changes in mechanical and ballistic properties. This process required significant levels of analysis to evaluate how the radiation environment evolves within the spacecraft during the mission, and also to evaluate how dose is delivered into test articles within the irradiating facilities.

Caffrey, Jarvis↗

NASA NTRS2019

Analyses and Methods of Solid Rocket Motor Material Irradiation at Marshall Space Flight Center

The search for life on other worlds is among humanity’s greatest endeavors. Europa represents the most probable location to discover extraterrestrial life in our solar system, owing to its surface composition of ice covering a liquid water ocean, warmed by the tidal forces of its orbit around Jupiter. Unfortunately, the Jovian system hosts the most intense planetary radiation environment in the solar system due to the charged particles, namely electrons and protons, trapped by Jupiter’s immense magnetic field. Any mission that attempts to approach or land on Europa must survive this radiation environment [Hand et al, 2017]. Radiation effects were identified as a priority risk to the successful development of a de-orbit stage and solid rocket motor (SRM) early in the Europa Lander De-orbit Stage project concept. The effects of primary concern tend to occur very near the outer surface of the SRM. The charged particles deposit their energy quickly and are mostly stopped in the outer metallic case, but a significant portion of radiation penetrates through the bondline and outer propellant regions. High doses of ionizing radiation are known to cause significant changes to mechanical properties of many materials, especially polymers. For polymers such as the rubber-like materials (elastomers) in a solid rocket motor, the primary damage mechanism is known as cross-linking, in which ionization causes the restructuring of the matrix of long polymer chains. Ionization energy breaks the long polymer chains and allows formation of new cross-linked bonding sites. This hardens and often strengthens the polymer, but at the cost of decreased flexibility (or modulus). Propellant, insulation, liner, and pyrotechnic materials were identified as higher risk items, and so were irradiated at Marshall Space Flight Center (MSFC) for investigation of changes in mechanical and ballistic properties. This process required significant levels of analysis to evaluate how the radiation environment evolves within the spacecraft during the mission, and also to evaluate how dose is delivered into test articles within the irradiating facilities.

Caffrey, Jarvis↗

NASA NTRS1986

Effects of thermal cycling on graphie-fiber-reinforced 6061 aluminum

Graphite-reinforced aluminum alloy metal-matrix composites are among materials being considered for structural components in dimensionally stable space structures. This application requires materials with low values of thermal expansions and high specific stiffnesses. They must remain stable during exposures to the space environment for periods extending to 20 years. The effects of thermal cycling on the thermal expansion behavior and mechanical properties of Thornel P100 graphite 6061 aluminum composites, as fabricated and after thermal processing to eliminate thermal strain hysteresis, have been investigated. Two groups of composites were studied: one was fabricated by hot roll bonding and the other by diffusion bonding. Processing significantly reduced strain hysteresis during thermal cycling in both groups and improved the ultimate tensile strength and modulus in the diffusion-bonded composites. Thermal cycling stabilized the as-fabricated composites by reducing the residual fabrication stress and increased the matrix strength by metallurgical aging. Thermal expansion behavior of both groups after processing was insensitive to thermal cycling. Data scatter was too large to determine effects of thermal cycling on the mechanical properties. The primary effects of processing and thermal cycling can be attributed to changes in the metallurgical condition and stress state of the matrix.

Dries, G. A.↗

NASA NTRS1998

IM7/LARC(tm) MPEI-1 Polymide Composites

LARC(Trademark) MPEI-1 (Langley Research Center(Trademark) modified phenylethynyl imide-1) phenylethynyl containing aromatic polymide, is based on the reaction of biphenyl dianhydride (BPDA), 3,4'-oxydianiline (3,4'-ODA), 1,3-bis(3-aminophenoxy)benzene (APB), 2,4,6-triaminopyrimidine (TAP) and 4-phenylethynyl phthalic anhydride (PEPA), presumably resulting in a mixture of linear, branched and star shaped phenylethynyl containing imides which was evaluated as a matrix for high-performance composites. The poly(amid acid) solution of MPEI-1 in N-methypyrrolidinone was synthesized at 35% and 42% solids. Unidirectional prepreg was fabricated from these solutions and Hercules IM7 carbon fiber utilizing NASA- Langley's multipurpose prepreg machine. The temperature-dependent volatile depletion rates, thermal crystallization behavior and resin theology were characterized. Based on this information, a composite molding cycle was developed which yielded well consolidated, void-free laminates. Composite mechanical properties such as short beam shear strength, longitudinal and transverse flexural strength and flexural modulus, longitudinal tensile strength and notched and unnotched compression strengths were measured at room temperature (RT) and elevated temperatures. These mechanical properties are compared with those of IM7/LARC(Trademark) PETI-5 composites.

Hou, T. H.↗

NASA NTRS2015

Impact Behavior of Composite Fan Blade Leading Edge Subcomponent with Thermoplastic Polyurethane Interleave

Impact damage tolerance and damage resistance is a critical metric for application of polymer matrix composites where failure caused by impact damage could compromise structural performance and safety. As a result, several materials and/or design approaches to improve impact damage tolerance have been investigated over the past several decades. Many composite toughening methodologies impart a trade-off between increased fracture toughness and compromised in-plane strength and modulus. In large part, mechanical tests to evaluate composite damage tolerance include static methods such as Mode I, Mode II, and mixed mode failures. However, ballistic impact damage resistance does not always correlate with static properties. The intent of this paper is to evaluate the influence of a thermoplastic polyurethane veil interleave on the static and dynamic performance of composite test articles. Static coupon tests included tension, compression, double cantilever beam, and end notch flexure. Measurement of the resistance to ballistic impact damage were made to evaluate the composites response to high speed impact. The interlayer material showed a decrease of in-plane performance with only a moderate improvement to Mode I and Mode II fracture toughness. However, significant benefit to impact damage tolerance was observed through ballistic tests.

Damage Tolerance↗

NASA NTRS1980

Dynamic modulus and damping of boron, silicon carbide, and alumina fibers

The dynamic modulus and damping capacity for boron, silicon carbide, and silicon carbide-coated boron fibers were measured from -190 to 800 C. The single fiber vibration test also allowed measurement of transverse thermal conductivity for the silicon carbide fibers. Temperature-dependent damping capacity data for alumina fibers were calculated from axial damping results for alumina-aluminum composites. The dynamic fiber data indicate essentially elastic behavior for both the silicon carbide and alumina fibers. In contrast, the boron-based fibers are strongly anelastic, displaying frequency-dependent moduli and very high microstructural damping. The single fiber damping results were compared with composite damping data in order to investigate the practical and basic effects of employing the four fiber types as reinforcement for aluminum and titanium matrices.

Dicarlo, J. A.↗

NASA NTRS2005

Mechanical Properties and Microstructure Investigation of Lead Free Solder

While the electronics industry appears to be focusing on Sn-Ag-Cu as the alloy of choice for lead free electronics assembly, ,the exact composition varies by geographic region, supplier and user. Add to that dissolved copper and silver from the printed circuit board traces and surface finish, and there can be significant variation in the final solder joint composition. A systematic study of the mechanical and microstructural properties of Sn-Ag-Cu alloys with Ag varying from 2wt% to 4wt% and Cu varying from 0.5wt% to lSwt%, was undertaken in this research study. Different sample preparation techniques (water quenched, oil quenched and water quenched followed by reflow) were explored and the resulting microstructure compared to that of a typical reflowed lead free chip scale package (CSP) solder joint. Tensile properties (modulus, 0.2% yield strength and the ultimate tensile strength) and creep behavior of selected alloy compositions (Sn-4Ag-1 X u , Sn-4Ag-OSCu, Sn- 2Ag-1 X u , Sn-2Ag-OSCu, Sn-3.5Ag-O.SCu) were determined for three conditions: as- cast; aged for 100 hours at 125OC; and aged for 250 hours at 125OC. There was no significant difference in Young's Modulus as a function of alloy composition. After an initial decrease in modulus after 100 hours at 125"C, there was an insignificant change with further aging. The distribution of 0.2% strain yield stress and ultimate tensile strength as a function of alloy composition was more significant and decreased with aging time and temperature. The microstructures of these alloys were examined using light and scanning electron microscopy (LM and SEM) respectively and SEM based energy dispersive x-ray spectroscopy (EDS). Fracture surface and cross-section analysis were performed on the specimens after creep testing. The creep testing results and the effect of high temperature aging on mechanical properties is presented for the oil quenched samples. In general the microstructure of oil quenched specimen exhibited a eutectic region of Sn with moderately dispersed Ag3Sn intermetallic, surrounded by a dendritic Sn-rich phase. The SEM images of the fracture surface indicated the presence of a tough shear surface at the initial cavity break area and a break line in the middle of specimen along the failure direction. A hyperbolic-sine creep model was adopted and used to fit the creep experiment data. The effect on the mechanical properties by adding the quaternary element bismuth to the Sn-3.5Ag-0.8Cu alloy was measured and compared with the mechanical properties of the ternary alloys. The results of this research study provide necessary data for the modeling of solder joint reliability for a range of Sn-Ag-Cu compositions and a baseline for evaluating the effects of subsequent quaternary additions.

Wang, Qing↗