Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “height estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Laboratory simulation of the rocket motor thrust as a follower force

Ground tests of solid propellant rocket motors have shown that metal-containing propellants produce various amounts of slag (primarily aluminum oxide), which is trapped in the motor case causing a loss of specific impulse. Although not yet definitely established, the presence of a liquid pool of slag also may contribute to nutational instabilities that have been observed with certain spin-stabilized, upper-stage vehicles. Because of the rocket's axial acceleration - absent in the ground tests - estimates of in-flight slag mass have been very uncertain. Yet such estimates are needed to determine the magnitude of the control authority of the systems required for eliminating the instability. A test rig with an eccentrically mounted hemispherical bowl was designed and built that incorporates a follower force that properly aligns the thrust vector along the axis of spin. A program that computes the motion of a point mass in the spinning and precessing bowl was written. Using various rpm, friction factors, and initial starting conditions, plots were generated showing the trace of the point mass around the inside of the fuel tank. The apparatus will be used extensively during the 1990 to 1991 academic year and incorporate future design features such as a variable nutation angle and a film height measuring instrument. Data obtained on the nutational instability characteristics will be used to determine order-of-magnitude estimates of control authority needed to minimize the sloshing effect.

Source record↗
NASA NTRS2017

CME Velocity and Acceleration Error Estimates Using the Bootstrap Method

The bootstrap method is used to determine errors of basic attributes of coronal mass ejections (CMEs) visually identified in images obtained by the Solar and Heliospheric Observatory (SOHO) mission's Large Angle and Spectrometric Coronagraph (LASCO) instruments. The basic parameters of CMEs are stored, among others, in a database known as the SOHO/LASCO CME catalog and are widely employed for many research studies. The basic attributes of CMEs (e.g. velocity and acceleration) are obtained from manually generated height-time plots. The subjective nature of manual measurements introduces random errors that are difficult to quantify. In many studies the impact of such measurement errors is overlooked. In this study we present a new possibility to estimate measurements errors in the basic attributes of CMEs. This approach is a computer-intensive method because it requires repeating the original data analysis procedure several times using replicate datasets. This is also commonly called the bootstrap method in the literature. We show that the bootstrap approach can be used to estimate the errors of the basic attributes of CMEs having moderately large numbers of height-time measurements. The velocity errors are in the vast majority small and depend mostly on the number of height-time points measured for a particular event. In the case of acceleration, the errors are significant, and for more than half of all CMEs, they are larger than the acceleration itself.

Michalek, Grzegorz↗
NASA NTRS2006

Merging IceSAT GLAS and Terra MODIS Data in Order to Derive Forest Type Specific Tree Heights in the Central Siberian Boreal Forest

Mapping of boreal forest's type, biomass, and other structural parameters are critical for understanding of the boreal forest's significance in the carbon cycle, its response to and impact on global climate change. We believe the nature of the forest structure information available from MISR and GLAS can be used to help identify forest type, age class, and estimate above ground biomass levels beyond that now possible with MODIS alone. The ground measurements will be used to develop relationships between remote sensing observables and forest characteristics and provide new information for understanding forest changes with respect to environmental change. Lidar is a laser altimeter that determines the distance from the instrument to the physical surface by measuring the time elapsed between the pulse emission and the reflected return. Other studies have shown that the returned signal may identify multiple returns originating from trees, building and other objects and permits the calculation of their height. Studies using field data have shown that lidar data can provide estimates of structural parameters such as biomass, stand volume and leaf area index and allows remarkable differentiation between primary and secondary forest. NASA's IceSAT Geoscience Laser Altimeter System (GLAS) was launched in January 2003 and collected data during February and September of that year. This study used data acquired over our study sites in central Siberia to examine the GLAS signal as a source of forest height and other structural characteristics. The purpose of our Siberia project is to improve forest cover maps and produce above-ground biomass maps of the boreal forest in Northern Eurasia from MODIS by incorporating structural information inherent in the Terra MISR and ICESAT Geoscience Laser Altimeter System (GLAS) instruments. A number of forest cover classifications exist for the boreal forest. We believe the limiting factor in these products is the lack of structural information, particularly in the vertical dimension. The emphasis of this project is to improve upon satellite maps of boreal forest structure parameters (i.e. height and biomass) using temporal, multi-angle, and vertical profile information of GLAS data. The existing and near future lidar data is useful for demonstrating these techniques and pursuing current estimates. Future lidar missions may be several years in the future, so we will work other new data sets that may aide in biomass estimates such as ALOS PALSAR We will continue this work to produce an accurate map of current above ground forest phytomass/carbon storage possible for the study area. We plan to develop, test, and integrate remote sensing methods for extracting forest canopy structure measures. We are compiling our field measurements and will compare them with the remote sensing methods where possible. We also be able to produce a realistic error bound on the remotely sensed carbon estimates.

Ranson, K. Jon↗
NASA NTRS2011

Video Meteor Fluxes

The flux of meteoroids, or number of meteoroids per unit area per unit time, is critical for calibrating models of meteoroid stream formation and for estimating the hazard to spacecraft from shower and sporadic meteors. Although observations of meteors in the millimetre to centimetre size range are common, flux measurements (particularly for sporadic meteors, which make up the majority of meteoroid flux) are less so. It is necessary to know the collecting area and collection time for a given set of observations, and to correct for observing biases and the sensitivity of the system. Previous measurements of sporadic fluxes are summarized in Figure 1; the values are given as a total number of meteoroids striking the earth in one year to a given limiting mass. The Gr n et al. (1985) flux model is included in the figure for reference. Fluxes for sporadic meteoroids impacting the Earth have been calculated for objects in the centimeter size range using Super-Schmidt observations (Hawkins & Upton, 1958); this study used about 300 meteors, and used only the physical area of overlap of the cameras at 90 km to calculate the flux, corrected for angular speed of meteors, since a large angular speed reduces the maximum brightness of the meteor on the film, and radiant elevation, which takes into account the geometric reduction in flux when the meteors are not perpendicular to the horizontal. They bring up corrections for both partial trails (which tends to increase the collecting area) and incomplete overlap at heights other than 90 km (which tends to decrease it) as effects that will affect the flux, but estimated that the two effects cancelled one another. Halliday et al. (1984) calculated the flux of meteorite-dropping fireballs with fragment masses greater than 50 g, over the physical area of sky accessible to the MORP fireball cameras, counting only observations in clear weather. In the micron size range, LDEF measurements of small craters on spacecraft have been used to estimate the flux (Love & Brownlee, 1993); here the physical area of the detector is well known, but the masses depend strongly on the unknown velocity distribution. In the same size range, Thomas & Netherway (1989) used the narrow-beam radar at Jindalee to calculate the flux of sporadics. In between these very large and very small sizes, a number of video and photographic observations were reduced by Ceplecha (2001). These fluxes were calculated (details are given in Ceplecha, 1988) taking the Halliday et al. (1984) MORP fireball fluxes, slightly corrected in mass, as a calibration, and adjusting the flux of small cameras to overlap with the number/mass relation from that work.

Campbell-Brown, M. D.↗
NASA NTRS2000

Apse-Alignment of the Uranian Rings

An explanation of the dynamical mechanism for apse-alignment of the eccentric Uranian rings is necessary before observations can be used to determine properties such as ring masses, particle sizes, and elasticities. The leading model relies on the ring self-gravity to accomplish this task, yet it yields equilibrium masses which are not in accord with Voyager radio measurements. We explore possible solutions such that the self-gravity and the collisional terms are both involved in the process of apse-alignment. We consider limits that correspond to a hot and a cold ring, and show that pressure terms may play a significant role in the equilibrium conditions for the narrow Uranian rings. In the cold ring case, where the scale height of the ring near periapse is comparable to the ring particle size, we introduce a new pressure correction pertaining to a region of the ring where the particles are locked in their relative positions and jammed against their neighbors, and the velocity dispersion is so low that the collisions are nearly elastic. In this case, we find a solution such that the ring self-gravity maintains apse-alignment against both differential precession (m = 1 mode) and the fluid pressure. We apply this model to the Uranian alpha ring, and show that, compared to the previous self-gravity model, the mass estimate for this ring increases by an order of magnitude. In the case of a hot ring, where the scale height can reach a value as much as fifty times larger than a particle size, we find velocity dispersion profiles that result in pressure forces which act in such a way as to alter the ring equilibrium conditions, again leading to a ring mass increase of an order of magnitude; however, such a velocity dispersion profile would require a different mechanism than is currently envisioned for establishing heating/cooling balance in a finite-sized, inelastic particle ring. Finally, we introduce an important correction to the model of Chiang and Goldreich.

Mosqueira, I.↗
NASA NTRS2013

Modeling of 2008 Kasatochi Volcanic Sulfate Direct Radiative Forcing: Assimilation of OMI SO2 Plume Height Data and Comparison with MODIS and CALIOP Observations

Volcanic SO2 column amount and injection height retrieved from the Ozone Monitoring Instrument (OMI) with the Extended Iterative Spectral Fitting (EISF) technique are used to initialize a global chemistry transport model (GEOS-Chem) to simulate the atmospheric transport and lifecycle of volcanic SO2 and sulfate aerosol from the 2008 Kasatochi eruption, and to subsequently estimate the direct shortwave, top-of-the-atmosphere radiative forcing of the volcanic sulfate aerosol. Analysis shows that the integrated use of OMI SO2 plume height in GEOS-Chem yields: (a) good agreement of the temporal evolution of 3-D volcanic sulfate distributions between model simulations and satellite observations from the Moderate Resolution Imaging Spectroradiometer (MODIS) and Cloud-Aerosol Lidar with Orthogonal Polarisation (CALIOP), and (b) an e-folding time for volcanic SO2 that is consistent with OMI measurements, reflecting SO2 oxidation in the upper troposphere and stratosphere is reliably represented in the model. However, a consistent (approx. 25 %) low bias is found in the GEOS-Chem simulated SO2 burden, and is likely due to a high (approx.20 %) bias of cloud liquid water amount (as compared to the MODIS cloud product) and the resultant stronger SO2 oxidation in the GEOS meteorological data during the first week after eruption when part of SO2 underwent aqueous-phase oxidation in clouds. Radiative transfer calculations show that the forcing by Kasatochi volcanic sulfate aerosol becomes negligible 6 months after the eruption, but its global average over the first month is -1.3W/sq m, with the majority of the forcing-influenced region located north of 20degN, and with daily peak values up to -2W/sq m on days 16-17. Sensitivity experiments show that every 2 km decrease of SO2 injection height in the GEOS-Chem simulations will result in a approx.25% decrease in volcanic sulfate forcing; similar sensitivity but opposite sign also holds for a 0.03 m increase of geometric radius of the volcanic aerosol particles. Both sensitivities highlight the need to characterize the SO2 plume height and aerosol particle size from space. While more research efforts are warranted, this study is among the first to assimilate both satellite-based SO2 plume height and amount into a chemical transport model for an improved simulation of volcanic SO2 and sulfate transport.

Wang, J.↗
NASA NTRS1985

Remote sensing of atmospheric and surface parameters from HIRS2/MSU on TIROS-N

At the Goddard Laboratory for Atmospheric Sciences (GLAS) a physically based satellite temperature sounding retrieval system was developed, involving the simultaneous analysis of sounding data, for determining atmospheric and surface conditions that are consistent with the observed radiances. In addition to determining accurate atmospheric temperature profiles even in the presence of clouds, the system provides global estimates of day and night sea or land surface temperatures, snow and ice cover, cloud amounts, cloudtop heights and temperatures, and albedo. The characteristics of the atmospheric and surface parameters derived from the GLAS Physical Retrieval System are reviewed, results for the FGGE year are presented and, whenever possible, compared with other measurements of the same fields. Some of the model-derived diagnostic fields available from the GLAS Analysis/Forecast System are also discussed. These fields may lead to more accurate determination of the source terms of the atmospheric heat and moisture budgets.

Susskind, J.↗
NASA NTRS1986

Measurements of the composition of aerosol component of Venusian atmosphere with Vega 1 lander, preliminary data

Preliminary investigation of mass spectra of gaseous products of pyrolyzed Venusian cloud particles collected and analyzed by the complex device of mass-spectrometer and collector pyrolyzer on board Vega 1 lander revealed the presence of heavy particles in the upper cloud layer. Based on 64 amu peak (SO2+), an estimate of the lower limit of the sulfuric acid aerosol content at the 62 to 54 km heights of approximately 2.0 mg/cu m is obtained. A chlorine line (35 and 37 amu) is also present in the mass spectrum with a lower limit of the chlorine concentration of approximately 0.3 mg/ cu m.

Surkov, Y. A.↗
NASA NTRS1991

Recovery of reflectance from imaging spectrometer measured radiance using a radiative transfer code

Radiance data were acquired over part of the Clark Mountain Range, California in 1990 by the Airborne Visible Infrared Imaging Spectrometer (AVIRIS). From these calibrated radiance data, the lateral distribution of water vapor in precipitable mm was recovered through analysis of the 940 nm water absorption. Surface pressure height was calculated from the 760 nm oxygen absorption band in the AVIRIS data. Surface slopes are estimated from relative elevations derived from the equivalent water vapor elevation for a standard atmosphere. Atmospheric optical depths measured at the Mountain Pass site in these data are extended to the entire region and varied based on the calculated surface pressure elevation. These parameters, derived from every AVIRIS spatial element, are used to constrain the LOWTRAN 7 radiative transfer code for the recovery of surface reflectance. Once transformed to reflectance, the imaging spectrometer data may be analyzed quantitatively for determination of surface composition, and compared with reflectance measurements acquired from different locations, times, and instruments.

Green, Robert O.↗
NASA NTRS1994

Determining the power-law wind-profile exponent under near-neutral stability conditions at sea

On the basis of 30 samples from near-simultaneous overwater measurements by pairs of anemometers located at different heights in the Gulf of Mexico and off the Chesapeake Bay, Virginia, the mean and standard deviation for the exponent of the power-law wind profile over the ocean under near-neutral atmospheric stability conditions were determined to be 0.11 +/- 0.03. Because this mean value is obtained from both deep and shallow water environments, it is recommended for use at sea to adjust the wind speed measurements at different heights to the standard height of 10 m above the mean sea surface. An example to apply this P value to estimate the momentum flux or wind stress is provided.

Hsu, S. A.↗
NASA NTRS1997

An Analysis of the Pressures, Forces and Moments Induced by the Ground Vortex Generated by a Single Impinging Jet

When a jet STOVL aircraft is in STOL operation the jets impinge on the ground and generate wall jets flowing radially outward from the points at which the jets impinge. When the forward flowing part of a wall jet meets the free stream flow it is rolled back on itself forming a parabolic shaped ground vortex. Positive pressures are induced on the lower surface of the configuration ahead of the ground vortex and suction pressures are induced over the ground vortex itself. In addition, the suction pressures induced aft of the jet out of ground effect are reduced and lifting pressures are induced on the upper surface. This study analyzes available pressure and force data and develops a method for estimating the forces and moments induced in ground effect. The method includes the effects of configuration variables, height and operating conditions, as well as the effects of the location, deflection and shape of the jet. However, it is limited to single jets at subcritical nozzle pressure ratios. An analysis of the effects of moving over the ground vs. tests over a fixed ground plane is included.

Kuhn, Richard E.↗
NASA NTRS1999

Advanced Techniques for Assessment of Postural and Locomotor Ataxia, Spatial Orientation, and Gaze Stability

In addition to adapting to microgravity, major neurovestibular problems of space flight include postflight difficulties with standing, walking, turning corners, and other activities that require stable upright posture and gaze stability. These difficulties inhibit astronauts' ability to stand or escape from their vehicle during emergencies. The long-ter7n goal of the NSBRI is the development of countermeasures to ameliorate the effects of long duration space flight. These countermeasures must be tested with valid and reliable tools. This project aims to develop quantitative, parametric approaches for assessing gaze stability and spatial orientation during normal gait and when gait is perturbed. Two of this year's most important findings concern head fixation distance and ideal trajectory analysis. During a normal cycle of walking the head moves up and down linearly. A simultaneous angular pitching motion of the head keeps it aligned toward an imaginary point in space at a distance of about one meter in front of a subject and along the line of march. This distance is called the head fixation distance. Head fixation distance provides the fundamental framework necessary for understanding the functional significance of the vestibular reflexes that couple head motion to eye motion. This framework facilitates the intelligent design of counter-measures for the effects of exposure to microgravity upon the vestibular ocular reflexes. Ideal trajectory analysis is a simple candidate countermeasure based upon quantifying body sway during repeated up and down stair stepping. It provides one number that estimates the body sway deviation from an ideal sinusoidal body sway trajectory normalized on the subject's height. This concept has been developed with NSBRI funding in less than one year. These findings are explained in more detail below. Compared to assessments of the vestibuo-ocular reflex, analysis of vestibular effects on locomotor function is relatively less well developed and quantified. We are improving this situation by applying methodologies such as nonlinear orbital stability to quantify responses and by using multivariate statistical approaches to link together the responses across separate tests. In this way we can exploit the information available and increase the ability to discriminate between normal and pathological responses. Measures of stability and orientation are compared to measures such as dynamic visual acuity and with balance function tests. The responses of normal human subjects and of patients having well documented pathophysiologies are being characterized. When these studies are completed, we should have a clearer idea about normal and abnormal patterns of eye, head, and body movements during locomotion and their stability in a wide range of environments. We plan eventually to use this information to validate the efficacy of candidate neurovestibular and neuromuscular rehabilitative techniques. Some representative studies made during this year are summarized.

Wall, Conrad., III↗
NASA NTRS1999

Nontangent, Developed Contour Bulkheads for a Wing-Body Single Stage Launch Vehicle

Dry weights for a SSTO vehicle which incorporates nontangent, developed contour bulkheads are estimated and compared to a baseline vehicle with 1.41 4 aspect ratio ellipsoidal bulkheads, Weights, volumes and heights of optimized bulkhead designs are computed using a preliminary design bulkhead analysis code. The dry weight of a vehicle which incorporates the optimized bulkheads is predicted using a vehicle weights and sizing code. Two optimization approaches are employed. A structural-level method, where the vehicle s three major bulkhead regions are optimized separately and then incorporated into a model for computation of the vehicle dry weight, predicts a reduction of 4365 Ib (2.2 percent) from the 200,679 Ib baseline vehicle dry weight. In the second, vehicle-level, approach, the vehicle dry weight is the objective function for the optimization. During the vehicle- level analysis, modified bulkhead designs are first analyzed, then incorporated into the weights model for computation of a dry weight. The optimizer simultaneously manipulates design variables for all three bulkheads to reduce the dry weight. The vehicle-level analysis predicts a dry weight reduction of 5129 Ib, a 2.6 percent reduction from the baseline value. These results suggest that nontangent, developed contour bulkheads may provide substantial weight savings for SSTO vehicles.

Wu, K. Chauncey↗
NASA NTRS2000

Performance and Optimization Metrics for Interferometric Radar

This paper provides a set of analytic equations that can be used to estimate system performance or to assist in the design of a system in that individual sources of height error can be balanced to minimize cost and maximize efficient use of resources.

optimization metrics interferometric radar interfe↗
NASA NTRS2004

Software for Generating Strip Maps from SAR Data

Jurassicprok is a computer program that generates strip-map digital elevation models and other data products from raw data acquired by an airborne synthetic-aperture radar (SAR) system. This software can process data from a variety of airborne SAR systems but is designed especially for the GeoSAR system, which is a dual-frequency (P- and X-band), single-pass interferometric SAR system for measuring elevation both at the bare ground surface and top of the vegetation canopy. Jurassicprok is a modified version of software developed previously for airborne-interferometric- SAR applications. The modifications were made to accommodate P-band interferometric processing, remove approximations that are not generally valid, and reduce processor-induced mapping errors to the centimeter level. Major additions and other improvements over the prior software include the following: a) A new, highly efficient multi-stage-modified wave-domain processing algorithm for accurately motion compensating ultra-wideband data; b) Adaptive regridding algorithms based on estimated noise and actual measured topography to reduce noise while maintaining spatial resolution; c) Exact expressions for height determination from interferogram data; d) Fully calibrated volumetric correlation data based on rigorous removal of geometric and signal-to-noise decorrelation terms; e) Strip range-Doppler image output in user-specified Doppler coordinates; f) An improved phase-unwrapping and absolute-phase-determination algorithm; g) A more flexible user interface with many additional processing options; h) Increased interferogram filtering options; and i) Ability to use disk space instead of random- access memory for some processing steps.

Hensley, Scott↗
NASA NTRSDate not supplied

Towards Physics Guided Optical Flow for Tracking Atmospheric Motion

Observations of atmospheric 3D winds are critical for improving short-range and long-range forecasting. Such advancement in forecasting directly applies to research in a number of areas including convective processes, wildfire plumes and tornado prediction. Atmospheric Motion Vectors (AMVs) provide a passively sensed approach to quantifying horizontal motion and cloud heights, which are typically sourced from geostationary sensors due to the availability of high frequency observations. Recent work has shown that estimating AMVs by tracking individual pixels with dense optical flow is a promising new direction. In this work, we compare state-of-the-art convolutional neural networks for optical flow in a physics-guided deep learning framework for predicting AMVs. The approach is semi-supervised and uses physically informed wind vectors from high-resolution numerical simulations for supervised learning followed by fine-tuning though warping and reconstruction of full-disk geostationary images (GOES-16). In the vertical direction, we use labels from the CALIPSO low-earth orbit satellite to predict cloud height from 16-band geostationary images with a neural network. We present results for both tasks on held-out time periods and secondary datasets.

Geostationary↗
NASA NTRS2009

Non-exercise Estimation of V02max Using a Dichotomy of Meeting or Not Meeting DHHS Physical Activity Recommendations

The physical activity guidelines (PAG) established by the US Dept. of Health and Human Services in 2008 is consistent with a rating of >/= 6 on the 11-point NASA Physical Activity Status Scale (PASS). Wier, et. al. developed non-exercise models for estimating VO2(sub max) from a combination of PASS, age, gender and either waist girth (WG) (R = 0.810, SEE= 4.799 ml/kg/min), %Fat (R = 0. 817, SEE = 4.716 ml/kg/min) or BMI (R = 0.802, SEE = 4.900 ml . kg-1. min -1 ). PURPOSE: to develop non-exercise models to estimate VO2max from age, gender, body composition (WG, %Fat, BMI) and PASS dichotomized at meets or does not meet the PAG (PAG-PASS), and to compare the accuracy of the PAG-PASS models with the models using the 11-point PASS. METHODS: 2417 men and 384 women were measured for VO2max by indirect calorimetry (RER >1.1); age (yr), gender by M = 1, W = 0; WG at the umbilicus; %fat by skin-folds, BMI by weight (kg) divided by height squared (m 2 ) , and PAGPASS by PASS < 6 = 0 and =/> 6 = 1. RESULTS: Three models were developed by multiple regression to estimate VO2(sub max) from age, gender, PAG-PASS and either WG (R = 0.790, SEE=5.019 ml/kg/min), %FAT (R= 0.080, SEE = 4.915 ml/kg/min) or BMI (R = 0.777, SEE = 5.162ml/kg/min). Cross-validation by the PRESS technique confirmed these statistics. Simple correlations between measured VO2(sub max) and estimates from the PAG-PASS models with WG, %Fat and BMI were 0.790, 0.800 and 0.777, minimally different from the correlations obtained with the PASS models (0.810, 0.810, and 0.802). PAG-PASS and PASS model constant errors were also similar: < 1 ml/kg/min for subsamples of age, gender, PASS and for VO2(sub max) between 30 and 50 ml/kg/min (70% of the sample) but > 1 ml/kg/min for VO2(sub max) <30 and >50 ml/kg/min. CONCLUSIONS: Non-exercise models using the combined effects of age, gender, body composition and the dichotomized PAG-PASS provide estimates of VO2(sub max) that are accurate for most adults, and the accuracy of these models are similar to previously published models using the 11-point PASS.

Wier, Larry T.↗
NASA NTRS1994

A comparison of winds from the STRATAN data assimilation system to balanced wind estimates

Winds derived from a stratospheric and tropospheric data assimilation system (STRATAN) are compared with balance winds derived from National Meteorological Center/Climate Analysis Center (NMC/CAC) heights. At middle latitudes in the lower stratosphere, the results show that STRATAN winds are comparable to the balance winds. In addition STRATAN winds provide useful horizontal divergence analyses, and hence, vertical velocity fields. More generally, the STRATAN winds are useful in a more extended domain than the balanced winds. In particular, they are useful in the Tropics and the upper stratosphere where the balanced winds fail. The assimilation also captures the quasi-biennial oscillation, but does not do a good job of representing tropical waves.

Coy, Lawrence↗