Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “heat flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

A knowledge gap analysis for transient CHF prediction within RELAP5-3D

Here we compare several experimental pool and flow boiling critical heat flux experiments with corresponding computational models developed with RELAP5-3D. Encompassed within this paper are several sensitivity analyses for the boiling heat transfer correlations, critical heat flux (CHF) prediction within RELAP5-3D and the thermal properties of the cladding for experiments in the Transient Reactor Test Loop (TRTL) and Transient Reactor Test (TREAT) facilities. The sensitivity analyses were consistent in determining that there is a large contribution from the critical heat flux multiplier which in this application, accounts for the effects of power transient critical heat flux. Comparison to experimental results of both the TREAT CHF-SERTTA experimental campaign and a University of New Mexico (UNM) pool boiling experimental campaign demonstrate both the under-prediction of transient CHF and nucleate boiling heat transfer. To address the gaps in knowledge regarding the transient heating effect for both boiling heat transfer and CHF prediction, we present an experimental test matrix for the TRTL facility that will isolate the power transient effect under PWR relevant operational conditions. The test matrix will incorporate 6 power pulses with a constant energy deposition and a timescale that spans over several orders of magnitude, including a steady state test with an exponential period of 10 s.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Development of Steady-State and Dynamic Mass and Energy Constrained Neural Networks for Distributed Chemical Systems Using Noisy Transient Data

The paper presents the development of algorithms for mass and energy constrained neural network models that can exactly conserve the overall mass and energy of distributed chemical process systems, even though the noisy transient data used for optimal model training violate the same. In contrast to approximately satisfying mass and energy balance constraints of a system by soft penalization of objective function, algorithms have been developed for solving equality-constrained nonlinear optimization problems, thus providing the guarantee of exactly satisfying the system mass and energy conservation laws. For developing dynamic mass-energy constrained network models for distributed systems, hybrid series and parallel dynamic-static neural networks have been leveraged. The developed algorithms for solving both the training and forward problems are validated using both steady-state and dynamic data in the presence of various noise characteristics. The developed data-driven algorithms are flexible to exactly satisfy mass and energy balance constraints for dynamic chemical processes if the system holdup information is available. The proposed network structures and algorithms are applied to the development of data-driven lumped and distributed models of an adiabatic superheater/reheater system, a nonisothermal continuous stirred tank reactor, as well as an electrically heated plug-flow reactor system where one form of energy gets transformed to another. It has been observed that the mass-energy constrained neural networks yield a root mean squared error of <1% with respect to the system truth for the case studies evaluated in this work.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

In Situ Structural and Electrical Conductivity Characterization of Sr2MMoO6-δ Double Perovskite Solid Oxide Fuel Cell Anode Materials

In this study, a series of Sr 2 MMoO 6-δ double perovskite solid oxide fuel cell (SOFC) anode materials (where 0 <= δ <= 0.041 and M = Fe, Co, or Ni) were synthesized, and the changes in their morphologies under relevant SOFC operating conditions were explored. Ultra-small-angle X-ray scattering (USAXS), small-angle X-ray scattering (SAXS), and wide-angle X-ray scattering (WAXS) were used to determine changes in the microstructures and phase compositions of the anode materials at high temperatures and under a reducing atmosphere. The stability of the double perovskite structure was found to be highly dependent on the identity of the cation M, such that when M = Fe, the material remained stable over the course of the experiments. However, when M = Co or Ni, significant changes in the microstructure and phase composition were observed. An in situ study of the M = Co sample, in which electrical conductivity and USAXS/SAXS/WAXS measurements were conducted simultaneously, revealed the structural degradation mechanisms and electrical conductivity changes over a range of temperatures. To conduct these measurements, a cell was developed that allowed for a sample mounted on Pt wires to be placed in the X-ray beam and heated under gas flow comprising 4% mass H 2 and 96% mass N 2 . The resulting measurements allowed for the direct comparison of the electrical and morphological changes occurring in the material under operating conditions, such that increases in conductivity could be attributed to the growth of new phases.

25 ENERGY STORAGE↗
DOE OSTI2026

Water-Fed, Photovoltaic-Driven Anion-Exchange Membrane Water Electrolysis for Solar Hydrogen Production

Direct coupled photovoltaic (PV)-electrolysis is a promising approach for low-cost hydrogen production, avoiding the need for separate electricity generation. Without solar concentration, the operating current densities of a PV-electrolyzer are small, and low capital costs are needed to reach hydrogen production cost targets (<$2/kg). Anion-exchange membrane (AEM) electrolyzers could be well-suited for this application due to their ability to use platinum group metal (PGM)-free catalysts and operate without supporting electrolytes, but a water-fed PV-AEM system has not yet been demonstrated. In this work, the performance of two AEM electrolyzer designs under pure-water, low-temperature, and diurnal-cycling conditions was evaluated. A simple PV-electrolyzer system design with direct electric coupling to a commercial 84 cm2 Si mini module and passive heating and water flow to the electrolyzer was used for on-sun testing in October 2025. The best-performing PV-AEM system achieved an average solar-to-hydrogen (STH) efficiency of 6.6% and a production rate of 15 mg/kWh/m2 of solar irradiance over 11 days. Minimal electrolyzer corrosion was observed, with no loss in efficiency over the diurnal cycles. While highlighting areas for improved electrolyzer and system design, this work is a proof of concept for distributed hydrogen production using inexpensive and abundant materials.

08 HYDROGEN↗
DOE OSTI2020

Charge exchange recombination spectroscopy at Wendelstein 7-X

The Charge Exchange Recombination Spectroscopy (CXRS) diagnostic has become a routine diagnostic on almost all major high temperature fusion experimental devices. For the optimized stellarator Wendelstein 7-X (W7-X), a highly flexible and extensive CXRS diagnostic has been built to provide high-resolution local measurements of several important plasma parameters using the recently commissioned neutral beam heating. This paper outlines the design specifics of the W7-X CXRS system and gives examples of the initial results obtained, to include typical ion temperature profiles for several common heating scenarios, toroidal flow and radial electric field derived from velocity measurements, beam attenuation via beam emission spectra, and normalized impurity density profiles under some typical plasma conditions.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Code Validation of SAM Using Forced and Natural Circulation Data from NACIE-UP Benchmark

Heavy liquid metals (HLMs) are promising candidates as coolants of Generation IV fast reactors due to their thermophysical properties. In the last decade, experimental work has been proposed as part of research and development efforts to develop such systems. In this context, researchers from the Brasimone Research Center have conducted many experiments using the Natural Circulation Experiment Upgrade (NACIE-UP) facility to study the thermofluid dynamic behavior of HLMs in rod bundle configurations with or without wire wrappers. This facility consists of a rectangular loop operated with lead-bismuth eutectic. Sensors across the loop monitor relevant parameters, i.e. temperatures, heat transfer, and flow conditions. Here, in the present work, we carefully select published data from NACIE-UP to validate the System Analysis Module (SAM), a modern system analysis code developed at Argonne National Laboratory. We developed one SAM model using specifications of the facility geometry and materials existing in relevant papers and reports. On top of that, these references provided the boundary conditions for simulating natural circulation and forced convection experiments in either steady or transient conditions. The SAM model simulates five test cases with diverse operating conditions. Ultimately, the code is proven to predict temperatures and mass flow rates that closely match the experiments. The discrepancies between numerical predictions and diverse transients are limited to a few degrees Celsius, showcasing that SAM is well suited for analyzing nuclear systems relying on HLM coolants.

advanced reactors↗
DOE OSTI2021

A multiscale insight into the growth of h-BN: effect of the enclosure

Abstract There is a lack of knowledge on the fundamental growth mechanisms governing the characteristics of 2D materials synthesized by the chemical vapor deposition (CVD) technique and their correlation with experimentally controllable parameters, which hindered their wafer-scale synthesis. Here, we pursued an analytical and computational approach to access the system states that are not experimentally viable to address these critical needs. We developed a multiscale computational framework correlating the macroscale heat and mass flow with the mesoscale morphology of the as-grown 2D materials by solving the coupled system of heat/mass transfer and phase-field equations. We used hexagonal boron nitride (h-BN) as our model material and investigated the effect of substrate enclosure on its growth kinetics and final morphology. We revealed a lower concentration with a more uniform distribution on the substrate in an enclosed-growth than open-growth. It leads to a more uniform size distribution of the h-BN islands, consistent with existing experimental investigations.

Materials Science↗
DOE OSTI2024

Spin-caloric resistance of Dirac plasma in a graphene Corbino device

The thermal resistance of a spin-polarized hydrodynamic Dirac plasma in graphene is considered. Here, a mechanism for the coupling of heat and spin flows is discussed, demonstrating that spin diffusion and spin thermocurrent modify viscous dissipation, leading to a significant enhancement of thermal resistance. Practical calculations are then presented for graphene devices in the Corbino geometry.

Graphene↗
DOE OSTI2021

Flow Assisted Evaporative Cooling for Electric Motor

This paper examines a novel concept of flow assisted latent heat driven two-phase evaporative cooling (EC) confined in-between slot liner and active-winding of electric motor. Wicking micro-structure enhanced PDMS liner axially sucks coolant in the form of thin film between the PDMS liner and active-winding and eventually enables thin film evaporation on the outer surface of the active-winding. Therefore, EC based thermal management eliminates contact resistance between the winding and slot-liner and, enhances the heat extraction from the winding without compromising the electro-magnetic performance. Two-way coupled electro-magnetic (EM) – computational fluid dynamics/heat transfer (CFD/HT) and EM - lumped parameter thermal network (LPTN) models have been developed to assess the electro-thermal performance of the EC under steady and transient conditions. Taking a case study of a 125 kW jacket cooled BMW i3 motor and dielectric coolant FC-84, EC is shown to be capable of handling a maximum steady state rms current density of 26 A/mm2 at a evaporative heat transfer coefficient of 5,000 W/m2.K, which is about 78.7% higher compared to the traditional jacket cooling (JC). In case of EC, a maximum steady state and transient rms current density of 30 A/mm2 (106.2% higher compared to the JC), and 40.8 A/mm2 have been realized by using high thermal conductivity epoxy (1.9 W/m.K) impregnation material. Thermal performance of the EC is also assessed and compared with JC over a dynamic drive cycle. Lastly, a motorette testing has been performed to demonstrate the applicability of the proposed EC method and to validate the developed modeling framework.

42 ENGINEERING↗
DOE OSTI2022

Chapter 2: Evaluating a Concentrating Solar Power Plantas an Extended-Duration Peaking Resource

We explore the ability of a concentrating solar power (CSP) plant with thermal energy storage (TES) to provide peaking capacity. We focus on future power systems, wherein net load patterns may be significantly different than they are today (e.g., due to higher renewable-energy penetrations). We examine 28 locations in the southwestern United States over an 18-year period. The hourly operation of the CSP plants are simulated to determine their potential to provide energy during an eight-hour peak-load window for each day up to 365 days per year. Our result shows that for the large majority of locations and years, CSP plants with certain configurations (i.e., in terms of solar field and TES sizes) can provide nearly 100% peak-load capacity. We examine also the amount of supplemental energy (e.g.,by using natural gas as a supplemental thermal-energy source) that would be required to ensure that a CSP plant could serve the eight highest-load hours of every day of the year. We find that in most cases, a CSP plant supplemented with natural gas would require less than 5% of the fuel that is used by a natural-gas fired power plant providing the same level of reliable capacity. A series of sensitivity analyses show that these results are robust to the number of peak-load hours and days that are considered and the configuration of the CSP plant.

capacity value↗
DOE OSTI2024

Modelling of cracking during beam oscillation laser welding of a creep-resistant nickel alloy

During high power laser welding of Inconel 740H, horizontal solidification cracks form at locations between approximately 70–80% of the weld depth. With the integration of circular beam oscillation, the laser energy density distribution and underlying thermo-mechanical conditions were altered. By coupling three-dimensional heat transfer, fluid flow, and stress modelling tools, the role that circular beam oscillation plays in the formation of the strain rates and stresses driving this cracking phenomenon was identified. While the addition of a circular oscillation pattern appeared to lower the stress levels along the solidification front, it did not eliminate the appearance of horizontal cracking. Only when the beam amplitudes reached 1.6 mm did solidification cracking disappear, but the weld depths were also significantly reduced.

Gao, Mingze↗
DOE OSTI2025

Non-circular electron beam spot welds in stainless steel alloys

Circularly symmetric-shaped spot welds are desirable for welding applications as they relate to heat and fluid flow conditions in the melt pool with predictable weld penetrations and repeatable results. Non-circular spot welds on the other hand result in undesirable and unpredictable weld penetrations or non-bridging of the liquid melt pool across the joint. Two known causes for non-circular melt pools occur when welding dissimilar metals, or when welding with skewed electron or laser beams that are not perpendicular to the surface. A largely unexplored additional factor, shown here, is an asymmetric power density distribution within the beam that can create non-circular melt pools even though the beam dimensions are much smaller than the melt pool itself.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Processed sap flow and fine-root trait data associated with summer drought responses in temperate trees in Lisle, Illinois, USA (2019–2021)

These data support the manuscript “Acquisitive root exploration strategies help maintain higher peak sap flux rates during summer drought, but more root biomass does not”. The dataset includes processed sap flow measurements and fine-root trait data collected between 2019 and 2021 from temperate monodominant tree plots established in the 1920s to 1930s ranging in size from 0.05 to 0.8 ha at The Morton Arboretum in Lisle, IL. Sap flow was measured with ICT sap flow sensors using the heat ratio method. Fine-root traits were measured from soil cores which includes specific root length (SRL), specific root area (SRA), diameter, biomass, and length for diameter classes ≤1 mm and ≤2 mm. The package contains comma separated value (CSV) data files and associated metadata that can be viewed and analyzed using common software such as spreadsheet programs, R, and Python. These data are used to investigate how variation in fine-root traits relate to tree water use and drought response during summer drought linking belowground root traits and aboveground physiological responses.

drought↗
DOE OSTI2020

UNESE Data Analysis - Disko Elm Gas Transport Characteristics (NA-22 Quarterly Report)

Two research papers describing gas transport studies in subsurface containment environments appropriate for underground nuclear explosions were revised and accepted for publication in the peer-reviewed journals, Nature – Scientific Reports and Journal of Geophysical Research. The Nature – Scientific Reports paper is a primary deliverable and describes the gas-transport experiment performed in P Tunnel (NNSS) and 1) subsequent analysis of field data as part of the UNESE program. The Journal of Geophysical Research paper describes an experiment, supported mainly by DARPA and led by researchers at Weston Geophysical and New Mexico Tech., with 2) analyses supported by this project to evaluate the ability of SF6 gas tracer to track xenon gas migration under conditions related to a previous UNESE experiment. Two new tasks consider 3) evaluation of detonation heating and multiphase flow on arrival of xenon at the surface and 4) the impact of surface or Langmuir adsorption of gases being transported through pores and along fractures.

58 GEOSCIENCES↗
DOE OSTI2022

Engineering Design of a Linde-BASF Advanced Post-Combustion CO 2 Capture Technology at a Linde Steam Methane Reforming H 2 Plant

Linde carried out an initial engineering design study for a Linde-BASF advanced post combustion CO 2 capture technology to be installed at a commercial-scale steam methane reforming (SMR) hydrogen plant located in the US Gulf Coast. This pre-FEED equivalent study included following: (1) basic design, including specific project scope definition and design basis, (2) basic engineering, including development of process flow diagrams and heat & material balances, (3) inside the battery limit (ISBL) equipment and systems specification, (4) balance of plant outside the battery limit (OSBL) equipment and systems specifications, (5) technology maturation plan, (6) hazard and operability (HAZOP) review, (7) environmental, health and safety (EH&S) assessment and environmental permitting analysis, (8) constructability review, (9) ISBL and OSBL EPC cost estimation, and (10) commercial-scale techno-economic analysis including capital expenditures (CAPEX) and operating expenditures (OPEX) and CO 2 capture cost estimates.

08 HYDROGEN↗
DOE OSTI2022

Enabling Parallel Execution of System-level Simulations in SAM

This report summarizes the recent code updates related to “element ghosting” in SAM to enable the parallel execution of system-level simulations using multiple processors/cores. Unlike typical MOOSE-based applications, for system-level simulations, SAM mostly deals with a collection of discrete small pieces of meshes, and the connection of physics on these meshes are realized by using “connector” types of components/code structures, such as conjugate heat transfer and flow junctions. The required code implementation is to correctly mark the necessary ghost elements for each type of such components/code structures; thus, the lower-level libraries can correctly perform the necessary data transfer between processors (CPUs) when executed in parallel mode. After the code updates, SAM can now run system-level simulations in the parallel mode. The parallel execution capability was then tested with an ABTR input model with 23k DOFs. Significant speedup was demonstrated when the optimal number of CPUs were used in parallel mode. Future systematic studies on parallelization performance using additional test cases covering different physics/scenarios will be needed to provide additional insights into the scalability of SAM parallelization.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

Overdriven Shocks: Recapturing a Lost Capability

Wallace’s theory for overdriven shocks in solids provides a theoretical framework for the strength of materials in the strong shock regime at strain rates unobtainable by current experimental means. Using irreversible thermodynamics, this theory incorporates heat and plastic flow as dissipative mechanisms under shock conditions allowing for the calculation of properties such as deviatoric stresses, plastic strains, and plastic strain rates. Though the theory is over four decades old, it has been used to calculate the strength behavior of only a small handful of metals. In this work, we have recaptured the ability to conduct this analysis, and two crucial aspects of the overdriven theory will be discussed: 1) the modeling assumptions that comprise this theoretical approach and 2) what information is needed to calculate the strength behavior for new materials.

36 MATERIALS SCIENCE↗