SEARCH · Engineering Papers

Results for “fourier analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

All sources NASA NTRS DOE OSTI

DOE OSTI2025

The composition of gases from a diffusion flame above longleaf pine needle fuel beds

The gas and tar composition of a diffusion flame from longleaf pine needles is currently poorly understood and more data are needed to fill in the gap between pyrolysis data and smoke plume data, thus improving physical and chemical modeling of wildland smoke formation. A pilot experiment to measure light gas and tar composition of such a flame is described for three flame regions: persistent flame (flame base), intermittent flame, and smoke plume. Flame gases from 24 experimental fires were collected in canisters and analyzed using EPA method TO-14A for CO 2 , CO, H 2 , CH 4 , and C 2 to C 7 hydrocarbon gases. Condensed gas (tar) samples were collected and analyzed using GC/MS. Other light gases were measured using FTIR spectroscopy. Results from compositional data analysis suggest significant differences in (relative) concentration of compounds detected in the three regions of the flame. Statistical tests for differences in flame zones were performed using the canister data: Concentration of hydrocarbons relative to CO and CO 2 decreased from the persistent flame zone above the pyrolyzing needles through the intermittent flame region into the flame-free plume. This was likely due to both chemical reactions (oxidation) occurring in the flame as well as the introduction of air into the flame/plume by entrainment.

Biomass↗

DOE OSTI2022

Annealing temperature variation and its influence on the self-cleaning properties of TiO 2 thin films

Titanium dioxide (TiO 2 ) is an important material in science and engineering because of its basic and synthetic properties. Nevertheless, there is a dearth of reports in the open literature focusing on its ability to self-clean under temperature changes. In this study, we used the spin coating technique to produce TiO 2 thin films to evaluate its self-cleaning ability after annealing at different temperatures. The TiO 2 sol was obtained through an endothermal sol-gel process, and the gel was coated on a glass substrate using a spin coater. The deposited films were then annealed at 400 °C, 600 °C, and 800 °C for 1 h. The influence of annealing temperature variation on the self-cleaning properties of the thin film was characterized using X-ray diffraction, scanning electron microscope; Fourier transformed infrared spectrometric analysis and UV-vis spectrophotometer. A test to ascertain self-cleaning was conducted using the degradation of methylene blue, and the different films were tested for durability. The durability test confirmed the connection between solid coating and substrate at all annealing temperatures. Thin films annealed at 600 °C revealed the best self-cleaning properties. The morphological analysis revealed snowflake shapes uniformly distributed over the substrate at 400 °C, and agglomeration improved as the annealing temperature increased. Structural analysis showed an increase in crystallinity with an increase in annealing temperature for both rutile and anatase phases. At three different temperatures, the chemical bond and the absorption band pattern followed the same path, although the peak intensity declined with temperature rise. Finally, the optical bandgap of the thin coated TiO 2 declined from 3.39 eV to 3.20 eV as the binding temperature increased from 400 to 800 °C.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Scale interactions and anisotropy in Rayleigh–Taylor turbulence

We study energy scale transfer in Rayleigh–Taylor (RT) flows by coarse graining in physical space without Fourier transforms, allowing scale analysis along the vertical direction. Two processes are responsible for kinetic energy flux across scales: baropycnal work Λ, due to large-scale pressure gradients acting on small scales of density and velocity; and deformation work Π, due to multiscale velocity. Our coarse-graining analysis shows how these fluxes exhibit self-similar evolution that is quadratic-in-time, similar to the RT mixing layer. We find that Λ is a conduit for potential energy, transferring energy non-locally from the largest scales to smaller scales in the inertial range where Π takes over. In three dimensions, Π continues a persistent cascade to smaller scales, whereas in two dimensions Π rechannels the energy back to larger scales despite the lack of vorticity conservation in two-dimensional (2-D) variable density flows. This gives rise to a positive feedback loop in 2-D RT (absent in three dimensions) in which mixing layer growth and the associated potential energy release are enhanced relative to 3-D RT, explaining the oft-observed larger α values in 2-D simulations. Despite higher bulk kinetic energy levels in two dimensions, small inertial scales are weaker than in three dimensions. Moreover, the net upscale cascade in two dimensions tends to isotropize the large-scale flow, in stark contrast to three dimensions. Furthermore, our findings indicate the absence of net upscale energy transfer in three-dimensional RT as is often claimed; growth of large-scale bubbles and spikes is not due to ‘mergers’ but solely due to baropycnal work Λ.

42 ENGINEERING↗

DOE OSTI2022

Conversion of Phenolic Oil from Biomass Pyrolysis into Phenyl Esters

Bio-oil is among the most economical approaches for advanced biofuel production. However, bio-oil faces several challenges including high acidity and viscosity, poor storage, and thermal stability. This study focuses on the upgradation of lignocellulosic (corn stover and yellow pine) bio-oil derived phenolic oil (PO), produced by the autothermal fast pyrolysis, through acid-catalyzed esterification reaction. Our strategy exploits a little recognized chemistry: the Fischer esterification of PO and carboxylic acids into carboxylic acid phenyl esters (CAPE) using Dean Stark distillation. Analyses by the Folin–Ciocalteu method, Karl Fischer titration, gas chromatography flame ionization detector, and the molecular weight determination by gel permeation chromatography suggest the conversion of 50 wt% added phenolics to their corresponding CAPE. The Fourier transform infrared spectroscopy analysis confirmed the formation of new C=O and two C–O stretching bands and decrease in the intensity of phenolic-OH bands in the CAPE. The 13 C NMR analysis supports the formation of CAPE together with some unreacted precursors. A base-catalyzed ester hydrolysis experiment and mass balance calculation show an excellent agreement (within 5% range) of the equivalent weight between the produced ester and the phenyl hexanoate. Brookfield analysis indicates that CAPE has 330-fold lower viscosity than starting PO. Heating values of CAPE were higher than PO, from which they were derived (42.2 and 43.6%, respectively, for PO from pyrolysis of corn stover and yellow pine), while moisture content decreased by 98.3 and 98.7%, respectively. The CAPE, which is a phenolic analogue of methyl esters used in biodiesel, has improved stability compared to PO from which it was derived.

42 ENGINEERING↗

DOE OSTI2022

Paired Simulations and Experimental Investigations into the Calcium-Dependent Conformation of Albumin

Serum albumin is the most abundant protein in blood plasma, and it is involved in multiple biological processes. Serum albumin has recently been adapted for improving biomaterial integration with bone tissue, and studies have shown the importance of this protein in bone repair and regeneration. However, the mechanism of action is not yet clear. In stark contrast, other studies have demonstrated that albumin blocks cell adhesion to surfaces, which is seen as a limitation to its bone healing role. These apparent contradictions suggest that the conformation of albumin facilitates its bioactivity, leading to enhanced bone repair. Serum albumin is known to play a major role in maintaining the calcium ion concentration in blood plasma. Due to the prevalence of calcium at bone repair and regeneration sites, it has been hypothesized that calcium binding to serum albumin triggers a conformational change, leading to bioactivity. In the current study, molecular modeling approaches including molecular docking, atomic molecular dynamics (MD) simulation, and coarse-grained MD simulation were used to test this hypothesis by investigating the conformational changes induced in bovine serum albumin by interaction with calcium ions. The computational results were qualitatively validated with experimental Fourier-transform infrared spectroscopy analysis. We find that free calcium ions in solution transiently bind with the three major loops in albumin, triggering a conformational change where N-terminal and C-terminal domains separate from each other in a partial unfolding process. The separation distance between these domains was found to correlate with the calcium ion concentration. The experimental data support the simulation results showing that albumin has enhanced conformational heterogeneity upon exposure to intermediate levels of calcium, without any significant secondary structure changes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Real-Time Alignment and Reorientation of Polymer Chains in Liquid Crystal Elastomers

Liquid crystal elastomers (LCEs) exhibit soft elasticity due to the alignment and reorientation of mesogens upon mechanical loading, which provides additional mechanisms to absorb and dissipate energy. This enhanced response makes LCEs potentially transformative materials for biomedical devices, tissue replacements, and protective equipment. However, there is a critical knowledge gap in understanding the highly rate-dependent dissipative behaviors of LCEs due to the lack of real-time characterization techniques that probe the microscale network structure and link it to the mechanical deformation of LCEs. In this work, we employ in situ optical measurements to evaluate the alignment and reorientation degree of mesogens in LCEs. The data are correlated to the quantitative physical analysis using polarized Fourier-transform infrared spectroscopy. The time scale of mesogen alignment is determined at different strain levels and loading rates. The mesogen reorientation kinetics is characterized to establish its relationship with the macroscale tensile strain, and compared to theoretical predictions. Overall, this work provides the first detailed study on the time-dependent evolution of mesogen alignment and reorientation in deformed LCEs. It also provides an effective and more accessible approach for other researchers to investigate the structural-property relationships of different types of polymers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Improving the performance for direct electrolysis of CO 2 in solid oxide electrolysis cells with a Sr 1.9 Fe 1.5 Mo 0.5 O 6– δ electrode via infiltration of Pr 6 O 11 nanoparticles

Direct CO 2 electrolysis using solid oxide electrolysis cells (CO 2 -SOECs) holds promise to efficiently convert carbon dioxide to carbon monoxide and oxygen. Cathodes with desirable catalytic activity and chemical stability play a critical role in the development of direct CO 2 -SOECs. Although Sr 2 Fe 1.5 Mo 0.5 O 6–δ (SFM) has exhibited promise for direct CO 2 -SOECs due to its redox stability, it suffers from insufficient activity for the CO 2 reduction reaction (CO 2 RR). Here we report interface engineering of nanosized Pr 6 O 11 on the SFM cathode obtained through infiltration to promote the CO 2 RR performance for direct CO 2 -SOECs. The effect of Pr 6 O 11 loading on the performance of the CO 2 RR is systematically investigated. At 800 °C, the current density of the Pr 6 O 11 infiltrated SFM cathode with an optimum Pr 6 O 11 loading of 14.8 wt% reaches 1.61 A cm –2 at 1.5 V, more than double that of the SFM cathode (0.76 A cm –2 ) under the same operating conditions. X-ray photoelectron spectroscopy (XPS) characterization and in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) analysis indicate that the adsorption ability of CO 2 on the SFM cathode has been significantly improved by the formation of Pr 6 O 11 . Temperature-programmed desorption (TPD) of CO 2 measurements further manifest that a 14.8 wt% Pr 6 O 11 -SFM cathode has better CO desorption capacity. In addition, polarization resistance of the SFM cathode has significantly decreased with the addition of Pr 6 O 11 . Three-electrode measurement was used to analyze the improved electrode kinetics. Finally, these results demonstrate that the formation of Pr 6 O 11 in the SFM cathode through infiltration is a promising approach for increasing CO 2 RR activity for CO 2 -SOECs.

03 NATURAL GAS↗

DOE OSTI2024

CO oxidation over a ligand coordinated single site Rh catalyst: identification of the active complex

Single atom catalysis has evolved as a promising strategy to enhance atom utilization efficiency, lower reaction temperatures, and control reaction pathways in heterogeneous catalytic reactions. An important challenge using supported single atom catalysts is the stability of metal single atoms during reactions. Here, we present an approach to stabilize single rhodium atoms on a titania support via a metal–ligand coordination strategy. We explore the reaction activity and mechanism of CO oxidation, as well as the stability under oxidative reaction conditions. Kinetic studies suggest that, with an excess of oxygen in the feed gas, oxygen activation is more facile on defective titania surfaces than on pristine titania surfaces. In situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) analysis shows that on the pristine titania surface, the 1,10-phenanthroline-5,6-dione (PDO) coordinated Rh catalyst (Rh–PDO/TiO 2 ) catalyzes CO oxidation via the formation of carbonate-like species, which is similar to what occurs on Rh nanoparticle catalysts. However, on the defective titania surface, no carbonate species form for Rh–PDO/def-TiO 2 . The supported Rh–ligand catalysts are also shown to be very stable in such a reaction environment at elevated temperatures, potentially allowing for wide applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Characterization of the Soluble and Insoluble Portions of Solids from the Salt Waste Processing Facility Tank 201 and Tank 202 Samples

The Salt Waste Processing Facility (SWPF) Tank 201 and Tank 202 samples have been characterized using X-ray diffraction (XRD), scanning electron microscope/energy dispersive x-ray (SEM/EDX), particle size analysis (PSA-Microtrac), Fourier transform-infrared (FT-IR) and nuclear magnetic resonance ( 1 H NMR) spectroscopic techniques to characterize and identify organic and inorganic components in Tanks 201 and 202 as part of efforts to understand the problems occurring at SWPF due to the presence of solids in the recovered solvent.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2023

Characterization of the Soluble and Insoluble Portions of Solids from the Salt Waste Processing Facility Tank 201 and Tank 202 Samples

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2020

Observation of Potential Contaminants in Processed Biomass Using Fourier Transform Infrared Spectroscopy

With rapidly increased interests in biomass, diverse chemical and biological processes have been applied for biomass utilization. Fourier transform infrared (FTIR) analysis has been used for characterizing different types of biomass and their products, including natural and processed biomass. During biomass treatments, some solvents and/or catalysts can be retained and contaminate biomass. In addition, contaminants can be generated by the decomposition of biomass components. Herein, we report FTIR analyses of a series of contaminants, such as various solvents, chemicals, enzymes, and possibly formed degradation by-products in the biomass conversion process along with poplar biomass. This information helps to prevent misunderstanding the FTIR analysis results of the processed biomass.

09 BIOMASS FUELS↗

DOE OSTI2022

On the Existence of Fast Modes in Compressible Magnetohydrodynamic Turbulence

Abstract We study the existence and properties of fast magnetosonic modes in 3D compressible MHD turbulence by carrying out a number of simulations with compressible and incompressible driving conditions. We use two approaches to determine the presence of fast modes: mode decomposition based on spatial variations only and spatio-temporal 4D fast Fourier transform (4D FFT) analysis of all fluctuations. The latter method enables us to quantify fluctuations that satisfy the dispersion relation of fast modes with finite frequency. Overall, we find that the fraction of fast modes identified via the spatio-temporal 4D FFT approach in total fluctuation power is either tiny with nearly incompressible driving or ∼2% with highly compressible driving. We discuss the implications of our results for understanding the compressible fluctuations in space and astrophysical plasmas.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2025

Constructing Co Cluster Sites for Selective CO 2 Hydrogenation via Phase Segregation from Co-Doped TiO 2 Nanocrystals

This article presents a Co phase segregation strategy for creating stable Co cluster catalytic sites on TiO 2 , enabling selective CO 2 hydrogenation to CO. Through oxidative calcination, pre-synthesized Co-doped brookite TiO 2 nanorods transform into a mixed TiO 2 phase, leading to the phase segregation of Co species. The resulting Co clusters, stabilized by strong Co-TiO 2 interactions during reductive CO 2 hydrogenation, effectively suppress the formation of larger nanoparticles. The undercoordinated sites of these clusters promote a high CO production rate with near-unit selectivity, contrasting with Co nanoparticles, which favor CH 4 formation under identical conditions. In-situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) analysis indicates that the weakened CO adsorption on Co clusters is key to their enhanced CO selectivity, highlighting this method as a promising approach for efficient CO 2 utilization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Nonoxidative dehydrogenation of propane using boron-incorporated silica-supported Pt Sites synthesized by atomic layer deposition

Nonoxidative dehydrogenation of propane to propylene using Pt-based supported catalysts is an active research area in catalysis because catalyst attributes of Pt sites can be controlled by careful design of active sites. One way to achieve this is by the addition of a second metal that may impart a change in the electron density of active sites, which in turn affects catalytic performance. In this study, bimetallic Pt and B sites were deposited on powder SiO2 using atomic layer deposition (ALD). Boron was first deposited on SiO2 via half-cycle ALD using triisoproplyborate as the B source. Following calcination, Pt deposition was performed via half-cycle ALD using trimethyl(methylcyclopentadienyl)platinum(IV) as the Pt source. The synthesized catalysts were reduced under H2 at 550 °C and characterized using inductively coupled plasma optical emission spectroscopy for elemental analysis, diffuse reflectance infrared Fourier transform spectroscopy of adsorbed CO to examine the properties of Pt, and time-resolved X-ray absorption near edge structure spectroscopy to examine the changes in the reducibility of Pt sites. The samples were then tested for nonoxidative dehydrogenation of propane at 550 °C using a fixed-bed plug-flow reactor to examine the role of B on the catalytic performance. Characterization results showed that the addition of B imparted an increase in electron density and affected the reducibility of Pt sites. In addition, incorporating B on SiO2 created anchoring sites for Pt ALD. The amount of Pt deposited on B/SiO2 was 2.2 times that on SiO2. Catalytic activity results revealed the addition of B did not change the initial activity of Pt sites significantly, but improved propylene selectivity from 80% to 87% and stability almost threefold. The enhanced selectivity and stability of PtB/SiO2 is most presumably due to favored desorption of propylene and mitigating coke formation under reaction conditions, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1975

Scanning thermal plumes

Over a three-year period 800 thermal line scans of power plant plumes were made by an airborne scanner, with ground truth measured concurrently at the plants. Computations using centered finite differences in the thermal scanning imagery show a lower bound in the horizontal temperature gradient in excess of 1.6 C/m. Gradients persist to 3 m below the surface. Vector plots of the velocity of thermal fronts are constructed by tracing the front motion in successive thermal images. A procedure is outlined for the two-point ground calibration of a thermal scanner from an equation describing the scanner signal and the voltage for two known temperatures. The modulation transfer function is then calculated by input of a thermal step function and application of digital time analysis techniques using Fast Fourier Transforms to the voltage output. Field calibration tests are discussed. Data accuracy is limited by the level of ground truth effort chosen.

Scarpace, F. L.↗

NASA NTRS1977

Computer control of a far infrared interferometer

A simple interface has been designed for the automatic control and data collection from a Grubb Parsons Mark III cube interferometer. A computer is used to automatically step the movable mirror on the interferometer. Data may be directly input into the computer for immediate transformation or stored for later analysis via a fast Fourier transformation. The interface is based on a commercial analog-to-digital converter having a parallel-to-serial data converter. The device can also display ASCII characters sent from the computer in parallel binary code. The system is applicable to recording interferograms having long time durations and to measuring multiple interferograms for statistical averaging.

Breecher, J.↗

NASA NTRS1980

Evaluation of space shuttle main engine fluid dynamic frequency response characteristics

In order to determine the POGO stability characteristics of the space shuttle main engine liquid oxygen (LOX) system, the fluid dynamic frequency response functions between elements in the SSME LOX system was evaluated, both analytically and experimentally. For the experimental data evaluation, a software package was written for the Hewlett-Packard 5451C Fourier analyzer. The POGO analysis software is documented and consists of five separate segments. Each segment is stored on the 5451C disc as an individual program and performs its own unique function. Two separate data reduction methods, a signal calibration, coherence or pulser signal based frequency response function blanking, and automatic plotting features are included in the program. The 5451C allows variable parameter transfer from program to program. This feature is used to advantage and requires only minimal user interface during the data reduction process. Experimental results are included and compared with the analytical predictions in order to adjust the general model and arrive at a realistic simulation of the POGO characteristics.

Gardner, T. G.↗

NASA NTRS1982

Laboratory modeling and analysis of aircraft-lightning interactions

Modeling studies of the interaction of a delta wing aircraft with direct lightning strikes were carried out using an approximate scale model of an F-106B. The model, which is three feet in length, is subjected to direct injection of fast current pulses supplied by wires, which simulate the lightning channel and are attached at various locations on the model. Measurements are made of the resulting transient electromagnetic fields using time derivative sensors. The sensor outputs are sampled and digitized by computer. The noise level is reduced by averaging the sensor output from ten input pulses at each sample time. Computer analysis of the measured fields includes Fourier transformation and the computation of transfer functions for the model. Prony analysis is also used to determine the natural frequencies of the model. Comparisons of model natural frequencies extracted by Prony analysis with those for in flight direct strike data usually show lower damping in the in flight case. This is indicative of either a lightning channel with a higher impedance than the wires on the model, only one attachment point, or short streamers instead of a long channel.

Turner, C. D.↗