Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flow instability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Crossflow Stability and Transition Experiments in Swept-Wing Flow

An experimental examination of crossflow instability and transition on a 45deg swept wing was conducted in the Arizona State University Unsteady Wind Tunnel. The stationary-vortex pattern and transition location are visualized by using both sublimating chemical and liquid-crystal coatings. Extensive hot-wire measurements were obtained at several measurement stations across a single vortex track. The mean and travelling wave disturbances were measured simultaneously. Stationary crossflow disturbance profiles were determined by subtracting either a reference or a span-averaged velocity profile from the mean velocity data. Mean, stationary crossflow, and traveling wave velocity data were presented as local boundary layer profiles and contour plots across a single stationary crossflow vortex track. Disturbance mode profiles and growth rates were determined. The experimental data are compared with predictions from linear stability theory.

Dagenhart, J. Ray↗
NASA NTRS1993

On the shear stabilization of capillary break-up of finite liquid bridges

In this paper we consider an isothermal finite liquid bridge under zero-gravity. A sinusoidal interfacial shear stress drives a nonparallel flow in the bridge. The linear stability of this flow to three-dimensional disturbances (which may deform the cylindrical gas-liquid interface) is determined numerically by solving an elliptic eigenvalue problem. Previous results on shear stabilization of capillary break-up of axially unbounded cylindrical interfaces containing a parallel flow are hereby extended to a nonparallel flow. The turning flow regions influence the stability significantly. However, for the particular cases considered, a small area in parameter space remains where the capillary instability is suppressed through interfacial shear. Second, non-axisymmetric oscillatory instabilities are found which originate from an interaction of the interface deformation and the basic flow. These instabilities may be the isothermal limit of the oscillatory instabilities observed in float-zone crystal growth.

Dijkstra, Henk A.↗
NASA NTRS1983

Stability experiments in rotating-disk flow

An experimental study of the transitional flow on a flat disk, rotating in still air, has been conducted. Using digitized hot-wire data, the axes of the stationary spiral vortices, which are the primary instability mechanism for the disk flow, have been mapped-out in terms of both spatial coordinates and velocity fluctuations. Data are presented for a clean disk and for a disk with a single, isolated roughness element. The data show that the disk vortices are generated at discrete roughness disturbance sites on the disk and that they propagate and grow as wave packets. The familiar vortex pattern of 30 or so vortices results only when these wave packets have merged and filled the entire circumference. The appearance of stationary, secondary vortices prior to turbulent breakdown has also been observed. Comparisons with linear stability theory show reasonable agreement with measured growth rate data.

Wilkinson, S. P.↗
NASA NTRS2014

Transient Convection Due to Imposed Heat Flux: Application to Liquid-Acquisition Devices

A model problem is considered that addresses the effect of heat load from an ambient laboratory environment on the temperature rise of liquid nitrogen inside an enclosure. This model has applications to liquid acquisition devices inside the cryogenic storage tanks used to transport vapor-free propellant to the main engine. We show that heat loads from Q = 0.001 to 10 W, with corresponding Rayleigh numbers from Ra = 109 to 1013, yield a range of unsteady convective states and temperature rise in the liquid. The results show that Q = 1 to 10 W (Ra = 1012 to 1013) yield temperature distributions along the enclosure height that are similar in trend to experimental measurements. Unsteady convection, which shows selfsimilarity in its planforms, is predicted for the range of heat-load conditions. The onset of convection occurs from a free-convection-dominated base flow that becomes unstable against convective instability generated at the bottom of the enclosure while the top of the enclosure is convectively stable. A number of modes are generated with small-scale thermals at the bottom of the enclosure in which the flow selforganizes into two symmetric modes prior to the onset of the propagation of the instability. These symmetric vertical modes transition to asymmetric modes that propagate as a traveling-wave-type motion of convective modes and are representative of the asymptotic convective state of the flow field. Intense vorticity production is created in the core of the flow field due to the fact that there is shear instability between the vertical and horizontal modes. For the higher Rayleigh numbers, 1012 to 1013, there is a transition from a stationary to a nonstationary response time signal of the flow and temperature fields with a mean value that increases with time over various time bands and regions of the enclosure.

Duval, Walter M. B.↗
NASA NTRS1992

Investigation of hypersonic shock-induced combustion in a hydrogen-air system

A numerical study is conducted to simulate the ballistic range experiments at Mach 5.11 and 6.46. The flow field is found to be unsteady with periodic instabilities originating in the stagnation zone. The unsteadiness of the flow field decreased with increase in the Mach number, thus indicating that it is possible to stabilize such flow fields with a high degree of overdrive. The frequency of periodic instability is determined using Fourier power spectrum and is found to be in good agreement with the experimental data. The physics of the instability is explained by the wave interaction models available in the literature.

Ahuja, J. K.↗
NASA NTRS1989

Nonlinear evolution of oblique waves on compressible shear layers

The effects of critical-layer nonlinearity on spatially growing oblique instability waves on compressible shear layers between two parallel streams are considered. The analysis shows that mean temperature nonuniformities cause nonlinearity to occur at much smaller amplitudes than it does when the flow is isothermal. The nonlinear instability wave growth rate effects are described by an integrodifferential equation which bears some resemblance to the Landau equation, in that it involves a cubic-type nonlinearity. The numerical solutions to this equation are worked out and discussed in some detail. Inviscid solutions always end in a singularity at a finite downstream distance, but viscosity can eliminate this singularity for certain parameter ranges.

Goldstein, M. E.↗
NASA NTRS1996

Nonlinear stability of supersonic jets

The stability calculations made for a shock-free supersonic jet using the model based on parabolized stability equations are presented. In this analysis the large scale structures, which play a dominant role in the mixing as well as the noise radiated, are modeled as instability waves. This model takes into consideration non-parallel flow effects and also nonlinear interaction of the instability waves. The stability calculations have been performed for different frequencies and mode numbers over a range of jet operating temperatures. Comparisons are made, where appropriate, with the solutions to Rayleigh's equation (linear, inviscid analysis with the assumption of parallel flow). The comparison of the solutions obtained using the two approaches show very good agreement.

Tiwari, S. N.↗
NASA NTRS1995

Nonlinear Stability of Supersonic Jets

This paper presents stability calculations made for a shock-free supersonic jet using the model based on parabolized stability equations. In this analysis the large-scale structures, which play a dominant role in the mixing as well as the noise radiated, are modeled as instability waves. This model takes into consideration non-parallel flow effects and also nonlinear interaction of the instability waves. The stability calculations have been performed for different frequencies and mode numbers over a range of jet operating temperatures. Comparisons are made, where appropriate, with the solutions to Rayleigh's equation (linear, inviscid analysis with the assumption of parallel flow). The comparison of the solutions obtained using the two approaches show very good agreement.

Bhat, T. R. S.↗
NASA NTRS1991

Reynolds number effects on supersonic asymmetrical flows over a cone at high angle of attack

The supersonic viscous flow over a 5-degree half-angle cone at an angle of attack of four times the cone half-angle is studied computationally using both the conical and the three-dimensional Navier-Stokes equations. The numerical solutions were obtained with an implicit, upwind-biased algorithm. Asymmetrical flowfields of the absolute-instability type are found using the conical-flow equations which agree with published results. However, the absolute instabilities of the originally symmetric flow found with the conical equations do not occur in the three-dimensional simulations, although spurious asymmetric three-dimensional flows for symmetric bodies arise if the grid resolution is insufficient in the nose region. The asymmetric flows computed with the three-dimensional equations are convective instabilities and are possible if the local Reynolds number exceeds a critical value and a fixed geometric asymmetry is imposed. A continuous range of asymmetries can be developed, depending on the size of the disturbance and the Reynolds number. As the Reynolds number is increased, the asymmetries demonstrate a bistable behavior at levels of side force consistent with those predicted using the conical equations. Below a certain critical Reynolds number, any flow asymmetries arising from a geometrical asymmetry are damped with increasing distance downstream from the geometrical asymmetry.

Thomas, J. L.↗
NASA NTRS1994

Interaction of Oblique Instability Waves with Weak Streamwise Vortices

This paper is concerned with the effect of a weak spanwise-variable mean-flow distortion on the growth of oblique instability waves in a Blasius boundary layer. The streamwise component of the distortion velocity initially grows linearly with increasing streamwise distance, reaches a maximum, and eventually decays through the action of viscosity. This decay occurs slowly and allows the distortion to destabilize the Blasius flow over a relatively large streamwise region. It is shown that even relatively weak distortions can cause certain oblique Rayleigh instability waves to grow much faster than the usual two-dimensional Tollmien-Schlichting waves that would be the dominant instability modes in the absence of the distortion. The oblique instability waves can then become large enough to interact nonlinearly within a common critical layer. It is shown that the resulting nonlinearity is weak and that the common amplitude of the interacting oblique waves is governed by the amplitude evolution equation derived in Goldstein & Choi (1989). The implications of these results for Klebanoff-type transition are discussed.

Goldstein, M. E.↗
NASA NTRS1980

On the stabilization of three-dimensional boundary layers by suction and cooling

A significant reduction in the drag of transonic aircraft can be achieved by using an active method of boundary-layer control to maintain laminar flow on the aerodynamic surfaces. The stabilizing influence of suction for both favorable and adverse pressure gradients is demonstrated by means of the self-similar incompressible three-dimensional boundary layers on yawed wedges. Profile instability is measured by the maximum amplification rate of fixed-frequency disturbances computed according to linearized, locally parallel, spatial stability theory. Suction is found to be more effective in controlling Tollmien-Schlichting instability than stationary cross-flow disturbances. The effectiveness of surface cooling as a method of stabilization is compared with suction for the boundary layers on a transonic 35 deg swept wing of infinite span. It is found from compressible stability theory that when the surface is cooled to a uniform temperature such that the maximum cross-flow velocity is reduced by the same amount as with a uniform suction distribution, the stabilizing effect of cooling on cross-flow disturbances is less than with suction.

Mack, L. M.↗
NASA NTRSDate not supplied

Automatic Generation of Guard-Stable Floating-Point Code

In floating-point programs, test instability occurs when the control flow of a conditional statement diverges from its ideal execution under real arithmetic. This phenomenon is caused by the presence of round-off errors in floating-point computations. Writing programs that correctly handle test instability often require expertise on finite precision computations and rounding errors. This paper presents a fully automatic tool chain that generates and formally verifies a test-stable floating-point C program from its functional specification in real arithmetic. The generated program is instrumented to soundly detect when unstable tests may occur and, in these cases, to issue a warning. The proposed approach combines the PRECiSA floating-point static analyzer, the Frama-C software verification suite, and the PVS theorem prover.

Floating-Point Arithmetic↗
NASA NTRS1992

What we learn about cooling flows through the study of the 10,000 K gas in clusters

The physical properties of the emission-line nebulae associated with central dominant galaxies in clusters are explored within the context of standard cooling-flow models of the hot ICM. It is pointed out that the properties of the 10,000 K gas are inconsistent with simple theories in which this gas has accreted out of the hot ICM in thermal instabilities within a standard cooling flow atmosphere. Several possible ramifications for our understanding of the properties of clusters and the hot intracluster medium are discussed.

Baum, Stefi A.↗
NASA NTRS2009

Stability Analysis of Roughness Array Wake in a High-Speed Boundary Layer

Computations are performed to examine the effects of both an isolated and spanwise periodic array of trip elements on a high-speed laminar boundary layer, so as to identify the potential physical mechanisms underlying an earlier transition to turbulence as a result of the trip(s). In the context of a 0.333 scale model of the Hyper-X forebody configuration, the time accurate solution for an array of ramp shaped trips asymptotes to a stationary field at large times, indicating the likely absence of a strong absolute instability in the mildly separated flow due to the trips. A prominent feature of the wake flow behind the trip array corresponds to streamwise streaks that are further amplified in passing through the compression corner. Stability analysis of the streaks using a spatial, 2D eigenvalue approach reveals the potential for a strong convective instability that might explain the earlier onset of turbulence within the array wake. The dominant modes of streak instability are primarily sustained by the spanwise gradients associated with the streaks and lead to integrated logarithmic amplification factors (N factors) approaching 7 over the first ramp of the scaled Hyper-X forebody, and substantially higher over the second ramp. Additional computations are presented to shed further light on the effects of both trip geometry and the presence of a compression corner on the evolution of the streaks.

Choudhari, Meelan↗
NASA NTRS2022

Nonlinear Evolution of Instabilities in a Laminar Separation Bubble at a Hypersonic Mach Number

The development of both convective stationary perturbation as well as global instabilities in the vicinity of a laminar separation bubble above an axisymmetric compression corner in a hypersonic flow is investigated using numerical simulations. The flow configuration of primary interest corresponds to the cone-cylinder-flare model used in experimental measurements in the Boeing/AFOSR Mach-6 Quiet Tunnel at Purdue University. For a flare angle of 10 degrees and a unit Reynolds number of 11.5 x 10 6 m -1 , their surface flow visualizations identified the presence of streamwise elongated thermal streaks near the reattachment position and the dominant azimuthal spacing between the streaks was determined to be approximately 10 degrees (i.e., an azimuthal mode number of 36). Previous linear stability analyses predicted that the amplification characteristics of small amplitude, unsteady, convective instabilities within this flow were consistent with the surface pressure fluctuations measured in the experiment. However, their accompanying analysis of global instabilities had found the separation bubble to be weakly unstable at the 10 degrees flare angle, with the most unstable global mode corresponding to a stationary disturbance with an azimuthal wavenumber of m ≈ 5, which was well below the measured wavenumber of m = 36. Besides confirming the presence of the global instability at these flow conditions, the present numerical simulations quantify the details of the stationary equilibrium state associated with the supercritical bifurcation resulting from the nonlinear saturation of the unstable global mode. Although velocity perturbations associated with the saturated global mode are dominated by the fundamental spanwise wavelength associated with the linear global instability, the surface heat flux downstream of reattachment is dominated by m = 36 in agreement with experimental measurements. However, the shorter wavelength peak ( m = 36) in the azimuthal spectrum is not manifested as streaks with an azimuthal spacing of 10 degrees. An additional simulation of the combined evolution of both unsteady convective and global instabilities indicates that the nonlinear interactions between a broadband spectrum of oblique Mack’s first mode instabilities generate stationary vortex modes with a higher dominant wavenumber ( m = 60) as that observed in the experiments. Additional analyses are performed to predict the global mode behavior at other flare angles and how it differs from the convective centrifugal instability due to concave streamline curvature over the compression corner.

Hypersonic flow↗
NASA NTRS1990

Theoretical and experimental studies of baroclinic processes

The geophysical fluid flow simulation code, GEOSIM, is being used to study the phenomenon of vacillation in the baroclinic annulus. Having verified that the code predicts vacillation for the same points as the experiments, the work is aiming toward explaining the mechanics of vacillation and pointing out some of the sensitivities of the results to the numerical method. Researchers are finding that there is a structural change associated with amplitude vacillation, where the structural changes are in the vertical. The results disagree with the premise of Lindzen et al, that the vacillation is due to constructive and destructive interference of neutral modes with different phase speeds. The researchers are continuing to study the Spacelab 3 Geophysical Fluid Flow Cell (GFFC) results with horizontal temperature gradients and heating from below. GEOSIM has been used to compute a wide range of cases, and these are being compared with the observations. The computations and observations compare well, and the model is being used to extend the results beyond cases studied in the experiments and to study the mechanics and predictability of the flows. The study of fully nonlinear baroclinic instability using the GFFC apparatus is proceeding with the numerical code. While the first instability that occurs is of planetary scale, secondary instabilities consisting of small-scale, penetrative convection occurs where cold fluid flows over a warm surface. The simultaneous modeling of the planetary scale and the convective scale is possible because of the nonhydrostatic formulation of the model. Some of these results have been animated on the Stardent computer, which shows the explosive nature of the small-scale convection.

Miller, Tim↗
NASA NTRS1980

An explanation of the instability of the free vortex cores occurring over delta winds with raised edges

By rolling up the surfaces of discontinuity originating from the leading edge of delta wings, free vortex cores are formed above the wing. In case of greater angles of incidence, the flow in these vortex cores shows an instability which abruptly produces strong turbulence. In the present paper an explanation is given of this instability being a "frictionless instability" of the vortex core flow by increasing helical interference vortices. The occurring vortex core flows are calculated and investigated for stability by means of a stability criterion concerning flows with helical streamlines given by H. Ludwieg.

Ludwieg, H.↗