Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “feasibility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

The MRIS feasibility study

The Microwave Reflectometer Ionization Sensor (MRIS) is an instrument being developed for use in detecting and ranging of electron density layers in the reentry plasma of a space transfer vehicle. The rationale for the selection of the Double Sideband Suppressed Carrier (DSBSC) system used in the feasibility study for the MRIS is presented. A 25 GHz single-oscillator system and a 220 GHz double-oscillator system are described. The 25 GHz system was constructed and tested in the laboratory and test results are presented. As developed, the system employs a sideband spacing of 160 MHz. Based on an estimated electromagnetic wave velocity in the plasma, a round-trip phase shift measurement accuracy of +/- 7.6 degrees was required for the desired +/- 1/2 cm distance measurement accuracy. The interaction of parallel ground and reflecting planes produces interference that prevents the basic DSBSC system from meeting the accuracy goal so a frequency modulation was added to the system to allow averaging of the measured phase deviation. With an FM deviation of +/- 1 GHz, laboratory measurements were made for distances from 5 to 61 cm tip free space. Accounting for the plasma velocity factor, 82 percent of the data were equal to or better than the desired accuracy. Based on this measured result a sideband spacing to 250 MHz could be expected to yield data approximately 96 percent within the accuracy goal.

Neece, Robert T.↗
NASA NTRS1993

Physiological Anatomical Rodent Experiment (PARE) .04 Feasibility Test 1

The objective of this feasibility study was to investigate the environmental/treatment stresses in the proposed PARE.04 experiments in a ground based study to determine if these stresses were of sufficient magnitude to compromise the planned shuttle experiments. Eighty pregnant Sprague-Dawley rats were received on day 2 (day l equals day of vaginal plug) of gestation (G2) and on G7 60 were laparotomized to determine the condition of pregnancy and allow assignment to test groups. The five test groups (N equals 10 each group) were as follows: Group 1, nominal flight; Group 2, laparotomy control; Group 3, hysterectomy control; Group 4, vivarium control; Group 5, caesarean delivery. On G17, groups 1, 2, and 5 were subjected to unilateral hysterectomy to obtain fetuses for evaluation. There was no difference in fetal crown-rump length, fetal weight, or placental weight in any of the test groups subjected to unilateral hysterectomy at G17. Animals were allowed to go to term and animals in each group delivered between the morning of G22 and the afternoon of G23. Rats assigned to Group 5 began delivering vaginally prior to the designated time for caesarean section, thus only 2 animals in this group were delivered by caesarean section. After delivery, a blood sample was taken from the dam, and they were euthanized and the thymus and adrenal glands weighed. Pups from experimental dams were tattooed for identification, the anogenital distance of male pups was photographed for later measurement, and all pups placed with foster dams and litter sizes were standardized to 10. On day 7, all pups were euthanized, and pup adrenal glands and thymus weighed. Laparotomy at G7 with or without unilateral hysterectomy at G17, had no effect on pregnancy maintenance or vaginal delivery. There was no difference in maternal adrenal or thymus weights or plasma levels of catecholamines, estradiol, progesterone, or corticosterone. Likewise, there was no difference in the anogenital distance (index of fetal stress) of neonatal male pups, between any of the experimental groups. From days 0-7, weight gain from dams in all experimental groups was similar. Lastly, there was no difference in weights of thymus and adrenal glands in pups euthanized at day 7. Collectively, these data indicate that treatment stresses inherent in the proposed PARE.04 experimental design should not compromise the planned shuttle experiments.

Burden, Hubert W.↗
NASA NTRS1993

A feasibility study of a microgravity enhancement system for Space Station Freedom

The current low frequency microgravity requirements for Space Station Freedom (SSF) call for a level of less than 1 micro-g over 50 percent of all the laboratory racks for continuous periods of 30 days for at least 180 days per year. While this requirement is attainable for some of the laboratory modules for the Permanently Manned Configuration (PMC), it can not be met for the Man-Tended Configuration (MTC). In addition, many experiments would prefer even lower acceleration levels. To improve the microgravity environment, the Microgravity Enhancement System (MESYS) will apply a continuous thrust to SSF, to negate the disturbing gravity gradient and drag forces. The MESYS consists of a sensor, throttle-able thrusters and a control system. Both a proof mass system and accelerometer were evaluated for use as the sensor. The net result of the MESYS will be to shift the microgravity contours from the center of mass to a chosen location. Results indicate the MESYS is not feasible for MTC since it will require 5,073 kg of hydrazine fuel and 7,660 watts of power for 30 days of operation during average atmospheric conditions. For PMC, the MESYS is much more practical since only 4,008 kg of fuel and 5,640 watts of power are required.

Diamond, Preston S.↗
NASA NTRS1993

Distributed computing feasibility in a non-dedicated homogeneous distributed system

The low cost and availability of clusters of workstations have lead researchers to re-explore distributed computing using independent workstations. This approach may provide better cost/performance than tightly coupled multiprocessors. In practice, this approach often utilizes wasted cycles to run parallel jobs. The feasibility of such a non-dedicated parallel processing environment assuming workstation processes have preemptive priority over parallel tasks is addressed. An analytical model is developed to predict parallel job response times. Our model provides insight into how significantly workstation owner interference degrades parallel program performance. A new term task ratio, which relates the parallel task demand to the mean service demand of nonparallel workstation processes, is introduced. It was proposed that task ratio is a useful metric for determining how large the demand of a parallel applications must be in order to make efficient use of a non-dedicated distributed system.

Leutenegger, Scott T.↗
NASA NTRS1993

Feasibility of detecting aircraft wake vortices using passive microwave radiometers

The feasibility of detecting the cold core of the wake vortex from the wingtips of an aircraft using a passive microwave radiometer was investigated. It was determined that there is a possibility that a cold core whose physical temperature drop is 10 C or greater and which has a diameter of 5 m or greater can be detected by a microwave radiometer. The radiometer would be a noise injection balanced Dicke radiometer operating at a center frequency of 60 GHz. It would require a noise figure of 5 dB, a predetection bandwidth of 6 GHz, and an integration time of 2 seconds resulting in a radiometric sensitivity of 0.018 K. However, three additional studies are required. The first would determine what are the fluctuations in the radiometric antenna temperature due to short-term fluctuations in atmospheric pressure, temperature, and relative humidity. Second, what is the effect of the pressure and temperature drop within the cold core of the wake vortex on its opacity. The third area concerns the possibility of developing a 60 GHz radiometer with a radio metric sensitivity an order of magnitude improvement over the existing state of the art.

Harrington, Richard F.↗
NASA NTRS1993

Precipitation measurement using SIR-C: A feasibility study. Investigation at nadir

The most significant limitation of the imaging SAR in rain measurements is the ground return coupled to the rain cell. Here we report a study of the possibility of using the X-SAR and the C-band channel of SIR-C for rain measurement. Earlier signal-to-clutter calculations rule out the use of X-SAR at steeper off-vertical angles of incidence (i.e., 20 less than theta less than 50). Only rain rates greater than 30 mm/hr at angles of incidence greater than 60 degrees showed good signal-to-clutter ratio (SCR). This study involved calculations at vertical incidence. There is adequate signal-to-noise ratio (SNR) at vertical incidence, but the presence of high-range side-lobe levels leads to small SCR for measurement over oceans at both X and C bands. For larger rain thickness (greater than two km), the SCR gets better and smaller rain rates (greater than 10 mm/hr) can be measured. However, rain measurements over forests seem to be feasible at nadir even for smaller rain thickness (less than two km). We conclude that X band may be usable over the forest at vertical incidence to measure rain rates greater than five mm/hr even for shallow rain thickness and over ocean for large rain thickness.

Ahamad, Atiq↗
NASA NTRS1993

Feasibility study: Monodisperse polymer particles containing laser-excitable dyes

The objective was to determine the feasibility of the preparation of monodisperse spherical poly(methyl methacrylate) and polystyrene particles that contain laser-excitable dyes in the size range 0.1 microns to 1 cm. Poly(methyl methacrylate) and polystyrene were chosen because of their excellent optical properties. The sphericity was required for uniformity of spectral output of re-irradiated light from the dye-containing particles. The monodispersity was required to give each particle the same optical properties when exposed to laser light.

Vanderhoff, John W.↗
NASA NTRS1993

Demonstration of the feasibility of an integrated x ray laboratory for planetary exploration

The identification of minerals and elemental compositions is an important component in the geological and exobiological exploration of the solar system. X ray diffraction and fluorescence are common techniques for obtaining these data. The feasibility of combining these analytical techniques in an integrated x ray laboratory compatible with the volume, mass, and power constraints imposed by many planetary missions was demonstrated. Breadboard level hardware was developed to cover the range of diffraction lines produced by minerals, clays, and amorphous; and to detect the x ray fluorescence emissions of elements from carbon through uranium. These breadboard modules were fabricated and used to demonstrate the ability to detect elements and minerals. Additional effort is required to establish the detection limits of the breadboard modules and to integrate diffraction and fluorescence techniques into a single unit. It was concluded that this integrated x ray laboratory capability will be a valuable tool in the geological and exobiological exploration of the solar system.

Franco, E. D.↗
NASA NTRS1994

Structural design feasibility study of Space Station long spacer truss

The structural design and configuration feasibility of the long spacer truss assembly that will be used as part of the Space Station Freedom is the focus of this study. The structural analysis discussed herein is derived from the transient loading events presented in the Space Transportation System Interface Control Document (STS ICD). The transient loading events are liftoff, landing, and emergency landing loads. Quasi-static loading events were neglected in this study since the magnitude of the quasi-static acceleration factors is lower than that of the transient acceleration factors. Structural analysis of the proposed configuration of the long spacer truss with four longerons indicated that negative safety margins are possible. As a result, configuration changes were proposed. The primary configuration change suggested was to increase the number of truss longerons to six. The six-longeron truss appears to be a more promising structure than the four-longeron truss because it offers a positive margin of safety and more volume in its second bay (BAY2). This additional volume can be used for resupply of some of the orbital replacement units (such as a battery box). Note that the design effort on the long spacer truss has not fully begun and that calculations and reports of the negative safety margins are, to date, based on concept only.

Armand, Sasan C.↗
NASA NTRS1992

Overview of feasibility study on conducting overflight measurements of shaped sonic boom signatures using RPV's

Before beginning this presentation, it is appropriate to acknowledge the sincere interest and financial support provided by the NASA LaRC under contract NAS9-17900. An outline of the material to be used in the present paper is given. It begins with a indication of the origin and objectives of the feasibility study. This is followed by a discussion of various simulation methods of establishing the persistence of shaped sonic boom signatures to large distances including the use of recoverable RPV/drones. The desirable features to be sought out in an RPV along with a rationale for the selection of a 'shaped' sonic boom signature will be addressed. Three candidate vehicles are examined as to their suitability with respect to a number of factors, in particular, modifiability. Area distributions and associated sonic boom signatures of the basic and modified Firebee vehicle will also be shown. An indication of the scope of the proposed wind tunnel and flight test programs will be presented including measurement technologies and predicted waveforms. Finally, some remarks will be made summarizing the study and highlighting the key findings.

Maglieri, Domenic J.↗
NASA NTRS1994

Feasibility study of superconducting LSM rocket launcher system

A feasibility study is presented concerning an application of a superconducting linear synchronous motor (LSM) to a large-scale rocket launcher, whose acceleration guide tube of LSM armature windings is constructed 1,500 meters under the ground. The rocket is released from the linear launcher just after it gets to a peak speed of about 900 kilometers per hour, and it flies out of the guide tube to obtain the speed of 700 kilometers per hour at the height of 100 meters above ground. The linear launcher is brought to a stop at the ground surface for a very short time of 5 seconds by a quick control of deceleration. Very large current variations in the single-layer windings of the LSM armature, which are produced at the higher speed region of 600 to 900 kilometers per hour, are controlled successfully by adopting the double-layer windings. The proposed control method makes the rocket launcher ascend stably in the superconducting LSM system, controlling the Coriolis force.

Yoshida, Kinjiro↗
NASA NTRS1994

Optimal control theory determination of feasible return-to-launch-site aborts for the HL-20 Personnel Launch System vehicle

The personnel launch system (PLS) being studied by NASA is a system to complement the space shuttle and provide alternative access to space. The PLS consists of a manned spacecraft launched by an expendable launch vehicle (ELV). A candidate for the manned spacecraft is the HL-20 lifting body. In the event of an ELV malfunction during the initial portion of the ascent trajectory, the HL-20 will separate from the rocket and perform an unpowered return to launch site (RTLS) abort. This work details an investigation, using optimal control theory, of the RTLS abort scenario. The objective of the optimization was to maximize final altitude. With final altitude as the cost function, the feasibility of an RTLS abort at different times during the ascent was determined. The method of differential inclusions was used to determine the optimal state trajectories, and the optimal controls were then calculated from the optimal states and state rates.

Dutton, Kevin E.↗
NASA NTRS1994

Measurement uncertainty and feasibility study of a flush airdata system for a hypersonic flight experiment

Presented is a feasibility and error analysis for a hypersonic flush airdata system on a hypersonic flight experiment (HYFLITE). HYFLITE heating loads make intrusive airdata measurement impractical. Although this analysis is specifically for the HYFLITE vehicle and trajectory, the problems analyzed are generally applicable to hypersonic vehicles. A layout of the flush-port matrix is shown. Surface pressures are related airdata parameters using a simple aerodynamic model. The model is linearized using small perturbations and inverted using nonlinear least-squares. Effects of various error sources on the overall uncertainty are evaluated using an error simulation. Error sources modeled include boundarylayer/viscous interactions, pneumatic lag, thermal transpiration in the sensor pressure tubing, misalignment in the matrix layout, thermal warping of the vehicle nose, sampling resolution, and transducer error. Using simulated pressure data for input to the estimation algorithm, effects caused by various error sources are analyzed by comparing estimator outputs with the original trajectory. To obtain ensemble averages the simulation is run repeatedly and output statistics are compiled. Output errors resulting from the various error sources are presented as a function of Mach number. Final uncertainties with all modeled error sources included are presented as a function of Mach number.

Whitmore, Stephen A.↗
NASA NTRS1994

All feasible plans using temporal reasoning

An interval-based temporal reasoning algorithm is applied to planning problems. The generation of all feasible temporal plans and its importance are discussed.

Mitra, Debasis↗
NASA NTRS1994

STS propellant densification feasibility study data book

The feasibility of using densification or subcooling with respect to standard temperature propellants on the Space Transportation System (STS) in order to achieve a payload gain is discussed in this report. The objective is to determine the magnitude of the payload gain and to identify any system impacts to the space shuttle on either flight systems or ground systems. Results show that a payload benefit can be obtained by subcooling the liquid hydrogen (LH2) from a nominal temperature of 36.4 R to 28.5 R and by subcooling the liquid oxygen (LO2) from a nominal temperature of 164 R to either 132.1 R or 141.4 R. When the propellants are subcooled to 28.5 R and 132.1 R for the LH2 and LO2, respectively, a maximum payload gain of 7,324 lb can be achieved, and when the propellants are subcooled to 28.5 R and 141.5 R for the LH2 and LO2, respectively, a maximum payload gain of 6,841 lb can be achieved. If the LH2 is subcooled to 28.5 R while the LH2 and LO2 remains at the nominal conditions, a maximum payload gain of 1,303 lb can be achieved.

Fazah, M. M.↗
NASA NTRS1990

Cryogenic On-Orbit Liquid Depot Storage, Acquisition, and Transfer satellite (COLD-SAT) feasibility study

The Cryogenic On-Orbit Liquid Depot Storage, Acquisition, and Transfer Satellite (COLD-SAT) is an experimental spacecraft launched from an expendable launch vehicle which is designed to investigate the systems and technologies required for efficient, effective, and reliable management of cryogenic fluid in the reduced gravity space environment. The COLD-SAT program will provide the necessary data base and provide low-g proving of fluid and thermal models of cryogenic storage, transfer, and resupply concepts and processes. A conceptual approach was developed and an overview of the results of the 24 month COLD-SAT Phase A feasibility is described which includes: (1) a definition of the technology needs and the accompanying experimental 3 month baseline mission; (2) a description of the experiment subsystem, major features and rationale for satisfaction of primary and secondary experiment requirements using liquid hydrogen as the test fluid; and (3) a presentation of the conceptual design of the COLD-SAT spacecraft subsystems which support the on-orbit experiment with emphasis on areas of greatest challenge.

Bailey, William J.↗
NASA NTRS1990

Feasibility study for a Cryogenic On-Orbit Liquid Depot-Storage, Acquisition and Transfer (COLD-SAT) satellite

This feasibility study presents the conceptual design of a spacecraft for performing a series of cryogenic fluid management flight experiments. This spacecraft, the Cryogenic On-Orbit Liquid Depot-Storage, Acquisition, and Transfer (COLD-SAT) satellite, will use liquid hydrogen as the test fluid, be launched on a Delta expendable launch vehicle, and conduct a series of experiments over a two to three month period. These experiments will investigate the physics of subcritical cryogens in the low gravity space environment to characterize their behavior and to correlate the data with analytical and numerical models of in-space cryogenic fluid management systems. Primary technologies addressed by COLD-SAT are: (1) pressure control; (2) chilldown; (3) no-vent fill; (4) liquid acquisition device fill; (5) pressurization; (6) low-g fill and drain; (7) liquid acquisition device expulsion; (8) line chilldown; (9) thermodynamic state control; and (10) fluid dumping.

Rybak, S. C.↗
NASA NTRS1995

SEEK: A FORTRAN optimization program using a feasible directions gradient search

This report describes the use of computer program 'SEEK' which works in conjunction with two user-written subroutines and an input data file to perform an optimization procedure on a user's problem. The optimization method uses a modified feasible directions gradient technique. SEEK is written in ANSI standard Fortran 77, has an object size of about 46K bytes, and can be used on a personal computer running DOS. This report describes the use of the program and discusses the optimizing method. The program use is illustrated with four example problems: a bushing design, a helical coil spring design, a gear mesh design, and a two-parameter Weibull life-reliability curve fit.

Savage, M.↗