Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “elemental materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Minor elements in relict olivine grains of deep-sea spheres: Match with Mg-rich olivines from C2 meteorites

The bulk composition and relict minerals of meteoroid ablation spheres from deep sea sediments can be related to the parental material, and bulk compositions and elemental ratios favor a CI/CM affinity for most spheres. Although largely melted, some deep sea spheres (DSS) have retained rare grains apparently unmodified chemically by ablation heating or seawater alteration. Minor elements in relict olivines for comparison with compositions of olivines in known meteorites were analyzed. All relict olivines are very Mg rich. No terrestrial olivines match the chemical features which reinforces other evidence for an extraterrestrial origin. There is no match with achondritic olivines. Mg rich olivines occur in all types of carbonaceous meteorites, but the minor elements of most DSS olivines do not match with those for Allende (C3) olivines, and fit poorly with those of Murchison (C2) olivines. There is a good fit for Fe and Cr with those of the olivines in the unusual Belgica 7904 (C2) meteorite (3). It seems likely that the relict olivines of at least many deep sea spheres are chemically related to olivines in at least one C2 meteorite.

Smith, J. V.↗
NASA NTRS1985

Surface fatigue life and failure characteristics of EX-53, CBS 1000M, and AISI 9310 gear materials

Spur gear endurance tests and rolling-element surface fatigue tests are conducted to investigate EX-53 and CBS 1000M steels for use as advanced application gear materials, to determine their endurance characteristics, and to compare the results with the standard AISI 9310 gear material. The gear pitch diameter is 8.89 cm (3.50 in). Gear test conditions are an oil inlet temperature of 320 K (116 F), an oil outlet temperature of 350 K (170 F), a maximum Hertz stress of 1.71 GPa (248 ksi), and a speed of 10,000 rpm. Bench-type rolling-element fatigue tests are conducted at ambient temperature with a bar specimen speed of 12,500 rpm and a maximum Hertz stress of 4.83 GPa (700 ksi). The EX-53 test gears have a surface fatigue life of twice that of the AISI 9310 spur gears. The CBS 1000M test gears have a surface fatigue life of more than twice that of the AISI 9310 spur gears. However, the CBS 1000M gears experience a 30-percent tooth fracture failure which limits its use as a gear material. The rolling-contact fatigue lines of RC bar specimens of EX-53 and ASISI 9310 are approximately equal. However, the CBS 1000M RC specimens have a surface fatigue life of about 50 percent that of the AISI 9310.

Townsend, D. P.↗
NASA NTRS2010

Materials Development: Pitfalls, Successes, and Lessons

The incorporation of new or improved materials in aerospace systems, or indeed any systems, can yield tremendous payoffs in the system performance or cost, and in many cases can be enabling for a mission or concept. However, the availability of new materials requires advance development, and too often this is neglected or postponed, leaving a project or mission with little choice. In too many cases, the immediate reaction is to use what was used before; this usually turns out not to be possible and results in large sums of money, and amounts of time, being expended on reinvention rather than development of a material with extended capabilities. Material innovation and development is time consuming, with some common wisdom claiming that the timeline is at least 20 years. This time expands considerably when development is stopped and restarted, or knowledge is lost. Down selection of materials is necessary, especially as the Technical Readiness Level (TRL) increases. However, the costs must be considered and approaches should be taken to retain knowledge and allow for restarting the development process. Regardless of the exact time required, it is clear that it is necessary to have materials, at all stages of development, in a research and development pipeline and available for maturation as required. This talk will discuss some of theses issues, including some of the elements for a development path for materials. Some history of materials developments will be included. The usefulness of computational materials science, as a route to decreasing material development time, will be an important element of this discussion. Collaboration with outside institutions and nations is also critical for innovation, but raises the issues of intellectual property and protections, and national security (ITAR rules, for example).

Johnson, Sylvia M.↗
NASA NTRSDate not supplied

NASA’s Moon-to-Mars Planetary Autonomous Construction Technology Project: Overview and Status

NASA plans to land the first woman and next man on the Moon by 2025 through the initial Artemis missions. NASA and its international partners plan to establish a sustainable long-term presence on the lunar surface and build up infrastructure in the subsequent Artemis missions. The Lunar Surface Innovation Initiative (LSII), within NASA’s Space Technology Mission Directorate, aims to spur the creation of novel technologies needed for lunar surface exploration and accelerate the technology readiness of key systems and components. The primary thrust areas of LSII include sustainable power; dust mitigation; in-situ resource utilization; surface excavation, construction, and outfitting; and extreme access/extreme environments. The Moon-to-Mars Planetary Autonomous Construction Technology (MMPACT) projectwas initiated to address the lunar surface construction thrust area of LSII. The goal of the MMPACT project is to develop, deliver, and demonstrate on-demand capabilities to protect astronauts and create infrastructure on the lunar surface via construction of landing pads, habitats, shelters, roadways, berms and blast shields using lunar regolith-based materials. The MMPACT project is leveraging technology derived from NASA’s 3D Printed Mars Habitat Challenge along with contributions from other Government agencies, and multiple partners within industry and academia. The MMPACT project is comprised of three interrelated elements, construction hardware and process development; feedstock materials development; and microwave structure construction capabilities. These elements are working together to address the multiple challenges of infrastructure construction on the surface of the Moon including increased autonomy of operations, hardware operation and manufacturing under lunar environmental conditions, long-duration operation of mechanisms and parts, scale of construction activities, and material and construction requirements and standards. This presentation will summarize the status of development activities in each of the three elements, including testing of the various candidate materials, preliminary design concepts for future lunar infrastructure elements, and the vision for future technology demonstrations on the lunar surface. These demonstrations, targeting the mid-to-late 2020’s, are expected to enable landing pad construction and habitat construction resulting in commercial capabilities early in the next decade.

lunar infrastructure↗
NASA NTRSDate not supplied

NASA’s Moon-to-Mars Planetary Autonomous Construction Technology Project: Overview and Status

NASA plans to land the first woman and next man on the Moon by 2025 through the initial Artemis missions. NASA and its international partners plan to establish a sustainable long-term presence on the lunar surface and build up infrastructure in the subsequent Artemis missions. The Lunar Surface Innovation Initiative (LSII), within NASA’s Space Technology Mission Directorate, aims to spur the creation of novel technologies needed for lunar surface exploration and accelerate the technology readiness of key systems and components. The primary thrust areas of LSII include sustainable power; dust mitigation; in-situ resource utilization; surface excavation, construction, and outfitting; and extreme access/extreme environments. The Moon-to-Mars Planetary Autonomous Construction Technology (MMPACT) project was initiated to address the lunar surface construction thrust area of LSII. The goal of the MMPACT project is to develop, deliver, and demonstrate on-demand capabilities to protect astronauts and create infrastructure on the lunar surface via construction of landing pads, habitats, shelters, roadways, berms and blast shields using lunar regolith-based materials. The MMPACT project is leveraging technology derived from NASA’s 3D Printed Mars Habitat Challenge along with contributions from other Government agencies, and multiple partners within industry and academia. The MMPACT project is comprised of three interrelated elements, construction hardware and process development; feedstock materials development; and microwave structure construction capabilities. These elements are working together to address the multiple challenges of infrastructure construction on the surface of the Moon including increased autonomy of operations, hardware operation and manufacturing under lunar environmental conditions, long-duration operation of mechanisms and parts, scale of construction activities, and material and construction requirements and standards. This presentation will summarize the status of development activities in each of the three elements, including testing of the various candidate materials, preliminary design concepts for future lunar infrastructure elements, and the vision for future technology demonstrations on the lunar surface. These demonstrations, targeting the mid-to-late 2020’s, are expected to enable landing pad construction and habitat construction resulting in commercial capabilities early in the next decade.

Additive construction, regolith processing, lunar ↗
NASA NTRS2002

Thermostructural Analysis of Carbon Cloth Phenolic Material Tested at the Laser Hardened Material Evaluation Laboratory

RSRM nozzle liner components have been analyzed and tested to explore the occurrence of anomalous material performance known as pocketing erosion. Primary physical factors that contribute to pocketing seem to include the geometric permeability, which governs pore pressure magnitudes and hence load, and carbon fiber high temperature tensile strength, which defines a material limiting capability. The study reports on the results of a coupled thermostructural finite element analysis of Carbon Cloth Phenolic (CCP) material tested at the Laser Hardened Material Evaluation Laboratory (the LHMEL facility). Modeled test configurations will be limited to the special case of where temperature gradients are oriented perpendicular to the composite material ply angle. Analyses were conducted using a transient, one-dimensional flow/thermal finite element code that models pore pressure and temperature distributions and in an explicitly coupled formulation, passes this information to a 2-dimensional finite element structural model for determination of the stress/deformation behavior of the orthotropic fiber/matrix CCP. Pore pressures are generated by thermal decomposition of the phenolic resin which evolve as a multi-component gas phase which is partially trapped in the porous microstructure of the composite. The nature of resultant pressures are described by using the Darcy relationships which have been modified to permit a multi-specie mass and momentum balance including water vapor condensation. Solution to the conjugate flow/thermal equations were performed using the SINDA code. Of particular importance to this problem was the implementation of a char and deformation state dependent (geometric) permeability as describing a first order interaction between the flow/thermal and structural models. Material property models are used to characterize the solid phase mechanical stiffness and failure. Structural calculations were performed using the ABAQUS code. Iterations were made between the two codes involving the dependent variables temperature, pressure and across-ply strain level. Model results comparisons are made for three different surface heat rates and dependent variable sensitivities discussed for the various cases.

Clayton, J. Louie↗
NASA NTRS1979

Extraterrestrial processing and manufacturing of large space systems, volume 2, chapters 7-14 and appendices

Production and support equipment specifications are described for the space manufacturing facility (SMF). Defined production equipment includes electromagnetic pumps for liquid metal, metal alloying furnaces, die casters, electron beam welders and cutters, glass forming for structural elements, and rolling. A cost analysis is presented which includes the development, the aquisition of all SMF elements, initial operating cost, maintenance and logistics cost, cost of terrestrial materials, and transportation cost for each major element. Computer program listings and outputs are appended.

Miller, R. H.↗
NASA NTRS1981

Toward a space materials systems program

A program implementation model is presented which covers the early stages of space material processing and manufacturing. The model includes descriptions of major program elements, development and experiment requirements in space materials processing and manufacturing, and an integration of the model into NASA's long range plans as well as its evolution from present Materials Processing in Space plans.

Vontiesenhausen, G. F.↗
NASA NTRS1995

The Mode 1 mechanical crack tip stress field in hyperelastic and incompressible materials

The finite deformation field of a plane strain Mode 1 crack in a hyperelastic and incompressible material was examined under the assumptions of small scale nonlinearity. Finite element analyses were performed for two different material laws, a Neo-Hookean material and a third order invariant of a Rivlin material. The numerical results for both materials were compared to the appropriate theoretical asymptotic solution. A local cavitation locus surrounding the crack tip was identified for the Neo-Hookean material. For the third order invariant Rivlin material, maximum values of the dominant stress component were found close to the surface of the crack, above and below the deformed crack tip.

Quigley, Claudia J.↗
NASA NTRS2024

Metallurgical and Thermal Properties of 57Ni–40Ti–3Hf (wt%)

Selected properties of 57Ni-40Ti-3Hf (wt%) were measured to further develop this material for use in aerospace rolling-element bearings. The average grain size and microindentation hardness of the material at room temperature were 90 μm and 549 HV, respectively. From room temperature to 500 °C, electrical resistivity increased from 8.9×10 –7 to 11.3×10 –7 Ω⋅m, thermal expansion coefficients varied from 1.1×10 –5 to 1.2×10 –5 mm/mm⋅°C, specific heat increased from 0.44 to 0.53 W⋅sec/g⋅K, thermal diffusivity rose from approximately 0.003 to 0.005 cm 2 /sec and thermal conductivity increased from approximately 0.09 to 0.19 W/cm⋅K. The behavior of the material can be explained by well-known metallurgical theory. These results are expected to provide a basis for design and modeling of future aerospace components.

intermetallics↗
NASA NTRS2025

Metallurgical and Thermal Properties of 57Ni-40Ti-3Hf (wt%)

Selected properties of 57Ni-40Ti-3Hf (wt%) were measured to further develop this material for use in aerospace rolling-element bearings. The average grain size and microindentation hardness of the material at room temperature were 90 μm and 549 HV, respectively. From room temperature to 500 °C, electrical resistivity increased from 8.9×10–7 to 11.3×10–7 Ω⋅m, thermal expansion coefficients varied from 1.1×10–5 to 1.2×10–5 mm/mm⋅°C, specific heat increased from 0.44 to 0.53 W⋅sec/g⋅K, thermal diffusivity rose from approximately 0.003 to 0.005 cm2/sec and thermal conductivity increased from approximately 0.09 to 0.19 W/cm⋅K. The behavior of the material can be explained by well-known metallurgical theory. These results are expected to provide a basis for design and modeling of future aerospace components.

rule of mixtures↗
NASA NTRSDate not supplied

Thermal Protection System to Enable Ice Giant Aerocapture Mission for Delivering Both an Orbiter and an In Situ Probe

The Ice Giants have been identified as high priority science destinations in the last Decadal Survey [1] and could benefit from aerocapture as the primary method for orbit insertion [2]. A mass-efficient aerocapture system will enable the delivery of an orbiter along with an atmospheric probe (for in situ measurements to anchor global data collected by the orbiter) and possibly a lander at Triton [3]. Aerocapture could be executed either using low L/D rigid aeroshell with lift modulation (LMA) [4] or using deployable aeroshell using drag modulation (DMA) [3]. Nearly two decades ago, a NASA-funded team performed Neptune-Triton aerocapture studies with a mid-L/D lifting configuration [5] for achieving orbit using LMA. This study showed aerocapture challenges. Due to very high peak entry conditions combined with very high heat-load, a suite of TPS materials was required and this suite was deemed problematic from a qualification perspective, due test facility limitations. In the past 20 years, progress made in GN&C for lift-guided entry missions such as MSL, Orion EFT1, Mars 2020 and the upcoming Artemis missions, and the expertise in blunt body aerodynamics at large scale (~ 5m) has led the EDL community to conclude that aerocapture is a “go do” engineering activity and most technologies are in hand to propose missions with aerocapture [6] [7]. Aerocapture using DMA, currently in development, is an option for Ice Giant Missions. While DMA is simpler in some sense, due to ballistic entry and no need for lift-guided maneuvering, it has challenges and it’s maturity is lower. LMA and DMA both require one or more ablative Thermal Protection System (TPS) materials for the rigid aeroshell element. The ablative TPS needs to be robust and mass efficient due to the high heat loads and size of the rigid aeroshell. Currently, there are capable ablative thermal protection materials, e.g., Heatshield for Extreme Entry Environments Technology (HEEET), 3-D woven Mid-Density Carbon- Phenolic (3MDCP), and PICA (Phenolic-Impregnated Carbon Ablator) that are mature, i.e., at TRL 6 or higher. NASA also invested in Conformal PICA that was matured to TRL 5. Our goal is to evaluate the applicability of high TRL TPS and consider other design options. We first establish bounding aerocapture trajectories for a wide range of arrival conditions and the associated aerothermal environment. Based on the environments, we then determine the predicted TPS mass for the aeroshell [4]. In this presentation, we will outline the process by which we establish bounding aerocapture trajectories for hyperbolic excess velocities ranging from 27 km/s to 35 km/s, which are shown to be a range of velocities that can reduce the trip time from ~14 years to 8 years. The above velocity range translates to ~12 km/s to ~24 km/s arrival velocities at the planetary entry interface [2]. The velocity reduction required to achieve orbit ranges between ~2.5 km/s to 9.5 km/s for both Neptune and Triton. Propulsive insertion alone, due to the amount of fuel required to achieve the required velocity reduction, limits the science returned [2]. We establish the bounding aerocapture trajectories for a low L/D (~ 0.4) configuration for three different ballistic coefficients. The ballistic coefficient range is determined from three different aeroshell diameters of 3m, 4m and 5m and with an entry system mass of 2200 kg. With the above range of design parameters, we then determine conservative/bounding estimates of aerothermal environments by using a combination of CFD simulations and stagnation point heating estimates [7]. This engineering approach allows us to first assess the TPS need vs. TPS capability and determine the applicability of existing TPS. Once an applicable suite of TPS is determined, the TPS thickness and mass are computed. We show that the TPS mass fraction can be as low as 5% to as high as 20%, depending on total trip time reduction and other design parameters for a range of TPS. This is a large range for TPS mass fraction. We show PICA and HEEET can indeed enable aerocapture missions, but the missions incur a mass penalty. TPS mass savings, can be further reduced with the use of conformal PICA. Advancing the development of Conformal PICA to make it robust across the entire aerothermal environment (peak heat-flux, pressure and shear) range will result in TPS mass fractions of < 10% for Ice Giant aerocapture missions such as the Neptune-Triton mission. Aerocapture allows for not only shortening the trip time but enables larger mass to be placed in orbit. Furthermore, probes deployed from orbit will benefit in reduced entry environments allowing for a lower risk TPS implementation as compared to mission designs where the probe is released prior to orbit insertion. One of the challenges for the Ice Giant community is to ensure mission designs that maximize science and allow flexibility in the placement of the entry probe. The traditional approach to release the probe ahead of the orbiter may not optimize returned science. In this presentation, we will make the case for mature TPS such as HEEET and PICA. While these materials can enable aerocapture missions, completing the development of conformal PICA and extending Conformal PICA to be more robust, will have significant impact to TPS mass efficiency and significantly enhance science return for future Gas- and Ice-Giant missions.

E Venkatapathy↗
NASA NTRS2008

A Finite Element Analysis for Predicting the Residual Compressive Strength of Impact-Damaged Sandwich Panels

A simple analysis method has been developed for predicting the residual compressive strength of impact-damaged sandwich panels. The method is tailored for honeycomb core-based sandwich specimens that exhibit an indentation growth failure mode under axial compressive loading, which is driven largely by the crushing behavior of the core material. The analysis method is in the form of a finite element model, where the impact-damaged facesheet is represented using shell elements and the core material is represented using spring elements, aligned in the thickness direction of the core. The nonlinear crush response of the core material used in the analysis is based on data from flatwise compression tests. A comparison with a previous analysis method and some experimental data shows good agreement with results from this new approach.

Ratcliffe, James G.↗
NASA NTRS2008

A Finite Element Analysis for Predicting the Residual Compression Strength of Impact-Damaged Sandwich Panels

A simple analysis method has been developed for predicting the residual compression strength of impact-damaged sandwich panels. The method is tailored for honeycomb core-based sandwich specimens that exhibit an indentation growth failure mode under axial compression loading, which is driven largely by the crushing behavior of the core material. The analysis method is in the form of a finite element model, where the impact-damaged facesheet is represented using shell elements and the core material is represented using spring elements, aligned in the thickness direction of the core. The nonlinear crush response of the core material used in the analysis is based on data from flatwise compression tests. A comparison with a previous analysis method and some experimental data shows good agreement with results from this new approach.

Ratcliffe, James G.↗
NASA NTRS1993

Topology and layout optimization of discrete and continuum structures

The basic features of the ground structure method for truss structure an continuum problems are described. Problems with a large number of potential structural elements are considered using the compliance of the structure as the objective function. The design problem is the minimization of compliance for a given structural weight, and the design variables for truss problems are the cross-sectional areas of the individual truss members, while for continuum problems they are the variable densities of material in each of the elements of the FEM discretization. It is shown how homogenization theory can be applied to provide a relation between material density and the effective material properties of a periodic medium with a known microstructure of material and voids.

Bendsoe, Martin P.↗
NASA NTRS1992

Effect of process conditions and chemical composition on the microstructure and properties of chemically vapor deposited SiC, Si, ZnSe, ZnS and ZnS(x)Se(1-x)

Subatmospheric pressure CVD processes have been developed to produce theoretically dense, highly pure, void-free and large area bulk materials, SiC, Si, ZnSe, ZnS and ZnS(x)Se(1-x). These materials are used for optical elements, such as mirrors, lenses and windows, over a wide spectral range from the VUV to the IR. We discuss the effect of CVD process conditions on the microstructure and properties of these materials, with emphasis on optical performance. In addition, we discuss the effect of chemical composition on the properties of the composite material ZnS(x)Se(1-x). We first present a general overview of the bulk CVD process and the relationship between process conditions, such as temperature, pressure, reactant gas concentration and growth rate, and the microstructure, morphology and properties of CVD-grown materials. Then we discuss specific results for CVD-grown SiC, Si, ZnSe, ZnS and ZnS(x)Se(1-x).

Pickering, Michael A.↗
NASA NTRSDate not supplied

Novel Test and Analysis Methodology for the Assessment of Joint under Re-entry Environment

Spacecraft thermal protection systems require unique approaches for design verification due to the extreme environments seen during space travel and atmospheric re-entry. In this work, unique considerations for design, analysis, and verification of a tiled heatshield design with material nonlinearity, material property temperature-dependency, material property rate-dependency, and geometric stress concentrations are presented. Such designs require a thorough application of the building block approach to derive appropriate material property datasets, and a novel application of analysis models to aid in the structural verification with testing. The custom application of material rate-dependency in finite element analysis software is presented as a means of leveraging the rate-dependent test data for the material property dataset. Because bonded tile heatshields contain so many design considerations and nonlinearities which often preclude the ability to easily achieve the requisite test factors in qualification testing, a novel sub-element test was developed that amplifies the stress singularity beyond flight conditions. The test achieves an over-test over flight stress conditions. The approach for sub-element coupon design can be extended to other bonded joint designs and can be used in aiding a qualification program.

Pavel Babuska↗