Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “coating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Mechanical creep testing and characterization of Cr coated Zircaloy

Zirconium based cladding has been developed for use in light water reactor fuel applications due to the material’s desirable low neutron scattering cross section. To help improve corrosion resistance in accident conditions, such as a loss of coolant accident (LOCA), a chromium coating can be applied to the outer diameter of the Zircaloy tube. Cladding strength at reactor relevant temperatures is important for the structural performance. Stress relaxation creep testing was performed on Cr coated Zircaloy-4 to measure strain rate as a function of stress for 350 and 650°C. These were performed at both 5 ± 1 % and 7.5 ± 1 % strain. The lower temperature provides results near normal operating temperature, while the higher temperature provides results relevant to off-normal conditions where recrystallization will take place. Characterization was also performed to analyze the structure of the Cr coating and Zircaloy-4 as well as the interface between the two.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Monitoring the corrosion resistance of cold-spray coatings with membrane-based sensors

In this presentation, the MBES shows the ability to detect the change in exposed environment even with cold-spray coatings. Corrosion rates from the cold-spray coating were comparable to a 316 stainless steel sample. Defects in the coating did not impact sensor performance in terms of corrosion rate or water content detection. Energy dispersive X-ray spectroscopy was used to document ion migration into the membrane.

Rendon, Arnaldo↗
DOE OSTI2023

Self-assembled Seashell Like Coatings for Large Area Robust Debris Shields for Next Generation Pulsed Power Drivers

During this LDRD project, our team developed a technology which enables the fabrication of novel nanostructures replicating seashell – “nature’s toughest material”. The resulting coatings exhibit high thermal stability up to 1650°C, which exceeds the hardness of Spectra® by ~44%, as well as the compressive strength of aluminum by ~57%. Coatings made with this technology are stronger, environmentally friendly, more sustainable, and more versatile than other comparable materials. Beryllium wafers, the current, most favorable shielding material in terms of thermal and mechanical properties, are very toxic and cost hundreds of times more than the new material developed in this project. The coatings on silicon wafer and stainless steel, respectively, have been tested as ride-along on the Z machine and clearly outperform the bare substrate. Use of this technology will have a profound global impact for pulsed power and fusion energy development, debris mitigation for spacecraft and satellites, durability of drill bits used in deep well drilling and tunnel boring operations, thermal protection of aircraft and manned spacecraft, and various other thermal and mechanical protection applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Exploring the process-structure-property relationship of Aerosol Deposition to phosphor coatings for non-contact thermometry

Full-field, multi-measurand diagnostics provide rich validation data necessary to improve the product life cycle time of nuclear safety components. Thermophosphor digital image correlation (TP+DIC) is a method of simultaneously measuring strain and temperature fields using patterned phosphor coatings deposited with aerosol deposition (AD). While TP+DIC produces a functional diagnostic, the coating’s reproducibility and the effect of the patterned features on the inferred temperature remains uncharacterized. This NSR&D project provided the opportunity to study two areas: 1) the tunability and repeatability of aerosol deposition and 2) the robustness of aerosol deposition phosphor on deforming substrates. The first area explores the process-property relationship of parameters elucidating the significance of each on the coating. The second area explores the relationship between the features’ characteristics (namely thickness) and the phosphor emission and inferred temperature. Together, the results will lead to the improved accuracy and functionality of TP+DIC for qualification testing of nuclear safety components.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Fe-Coated Optical Fiber for Distributed Corrosion Monitoring in Soil and Aqueous Environment

Natural gas pipeline corrosion represents a substantial cost and safety concern during normal operations. The effective and real-time monitoring of corrosion is important to detect and mitigate pipeline risks before corrosion-related catastrophic events happen. Here, we describe the use of iron (Fe) coated optical fiber sensors (OFS) for distributed corrosion monitoring where Fe acts as a corrosion proxy. By using an optical backscattering reflectometer (OBR), corrosion was monitored based on the increase in the backscattered intensity amplitude of the light being passed as Fe underwent corrosion. The Fe-coated OFSs were prepared with a film thickness between 25–225 nanometers (nm) by an electroless plating approach and corroded by a carbon dioxide (CO2)-saturated acidic electrolyte. The corrosion rate (CR) was approximately 2.5 millimeters (mm)/year for Fe with a film thickness of 30 nm and increased with film thickness. Backscattering-based CRs were supported by visible light transmission measurements, which have been previously demonstrated. Additionally, a correlation between the intermittent transmission and residual Fe film thickness during the corrosion of Fe was established. The corrosion sensor was also tested in soil at > 1 foot depth. Fe-coated OFS was loaded into a Draka cable, which provides mechanical support during fiber deployment and installation into either acidified soil, top-soil, or sandy soil (50/50).

corrosion↗
DOE OSTI2025

Pathway to tune sputter coated Nb$_3$Sn with Zr

Superconducting radio frequency (SRF) cavities are essential elements of many modern-day particle accelerators such as, European XFEL (DESY), LCLS II-HE (SLAC) and PIP II (Fermilab). Nb$_3$Sn superconducting material promises significant potential to exceed the performance of conventional niobium based SRF cavities. We aim to advance the ongoing R$&$D efforts to achieve Nb$_3$Sn coated cavities with high material quality. In this work, we have developed to achieve a route for effectively reducing the intrinsic defects in magnetron sputter coated Nb$_3$Sn SRF cavities and eventually improve the overall RF performance. We have observed that Zr is mainly being incorporated as ZrO$_2$ precipitates of average dimensions ranging from 20-100nm. By increasing the concentration of Zr, we have three major effects in the physical properties. Firstly, we noted that the density of the surface and bulk voids as well as their average dimensions are dramatically reduced on increasing the Zr content in Nb$_3$Sn. These surface voids are believed to be detrimental to cavity applications due to increase the local dissipation of electric and magnetic fields. These results indicate that inclusion of Zr in Nb$_3$Sn sputtered coating will improve the material quality and might help to reduce the overall RF power dissipation. Secondly, we observed that increasing Zr concentration from 0 to 2.4% substantially improves both superconducting transition temperature (Tc) and upper critical magnetic field (Hc2). However, on further increasing the Zr concentration to 24%, we noticed a small decrement in the Hc2 value. These results infer that the increase in Zr concentration up to an optimal concentration will be beneficial to enhance the superconducting properties. Increase in Tc promises lesser RF losses and improvement in accelerating gradient, whereas the increase in Hc2 suggests more efficient flux pinning which could give rise to high quality factors in presence of multi-Tesla magnetic field. Additionally, we also observed that increasing Zr concentration possibly prevents the oxygen diffusion and leads to thinner formation of primary surface oxide (Nb$_2$O$_5$ and SnO). This study gives a route to tune Zr fraction in Nb3Sn to modify the physical properties that control the high field performance of Nb3Sn RF cavities.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Investigation of the Mechanical Degradation of Zinc-Based Cold Spray Coatings for Steel Pipelines

Internal corrosion in wet natural gas is a big challenge in the oil and gas industry due to corrosive constituents such as carbon dioxide (CO2), hydrogen sulfide (H2S), other forms of sulfur, and water in the gas stream. To mitigate internal corrosion, zinc-based cold spray coatings were designed for use in natural gas pipelines to increase the lifespan of the pipeline network. However, one of the requirements in designing internal coatings is the resistance of the coatings to mechanical forces applied on the pipeline's internal wall during pigging operations. These forces are primarily compressive and shear/friction forces. This study examines material properties that must be considered when evaluating mechanical considerations.

adhesion↗
DOE OSTI2025

Computational Design of Cost-Effective High-Entropy Thermal/Environmental Barrier Coatings

Developing cost-effective thermal/environmental barrier coatings (TEBC) requires balance among various properties including low thermal conductivity, matching coefficient of thermal expansion (CTE), high thermal stability, high fracture toughness, and high recession resistance while being affordable. Low oxygen diffusivity is desirable as it can slow down oxygen transport to reach the underlying bond coating and hence delay oxidation of the bond coating. This project aims to design low-cost high-performance TEBC based on high entropy rare earth disilicates to protect SiC-based ceramic matrix composites from chemical and thermal attack for better performance of components in the hot section of gas turbine engines. To accelerate the TEBC design, we utilize first-principles density functional theory to predict key properties including phase stability, CTE, lattice thermal conductivity, temperature-dependent elastic constants, and oxygen diffusivity. Alloying elements including Yb, Y, Er, Eu, Gd, Lu, La, and Ce are considered, and modeling prediction are compared with available experimental results.

coefficient of thermal expansion↗
DOE OSTI2025

Challenges of Vapor Diffusion $Nb_3Sn$ Coating at Fermilab: Minimizing Impurities Using TOF-SIMS

Nb$_3$Sn demonstrates steady advancements nowadays offering reduced power cost in superconducting radio-frequency cavities due to its high critical temperature, quality factor, and achieved accelerating gradient. However, theoretical estimates of its radio-frequency parameters have not been achieved due to several potentially limiting mechanisms: tin spots, patchy regions, defects, thermal impedance, and impurities. While some of these limitations have been intensively studied, impurity analysis in Nb$_3$Sn coatings have received less attention. We report an investigation of impurities in several vapor-diffused Nb$_3$Snn coated samples using time-of-flight secondary ion mass spectroscopy (TOF-SIMS) and show allowable impurity levels in view of superconducting cavity performance. Challenges and lessons learned in maintaining clean Nb$_3$Sn coatings are also discussed.

Tagdulang, N. [Fermilab]↗
DOE OSTI2021

Nanostructured Black Nickel Coating as Replacement for Black Cr(VI) Finish

This work compares different electrodeposition procedures to produce nickel black coatings as greener and less toxic alternatives to Cr(VI)-based coatings used in different applications. Nickel and nickel-plated brass served as substrates in studies with a Hull cell and polarization curves. After a set of comparative experiments, the best electrodeposition procedure was further studied and optimized. Optimal conditions were found with a bath consisting of 75 g/L NiCl2·6H2O + 30 g/L NaCl and a current density of 0.143 A dm−2 applied for 5 min at room temperature. Furthermore, a pre-treatment with 18.5 vol.% of hydrochloric acid in water was found to be necessary to warrant good coating adhesion to the substrate. The black color is attributed to the development of a nanostructured surface that absorbs the incident light. Corrosion testing was performed in 0.5 M NaCl aqueous solution using electrochemical impedance spectroscopy (EIS) and polarization tests.

Mennucci, Marina M. (ORCID:0000000171886804)↗
DOE OSTI2024

Novel One-Step Production of Carbon-Coated Sn Nanoparticles for High-Capacity Anodes in Lithium-Ion Batteries

Lithium-ion batteries offer the highest energy density of any currently available portable energy storage technology. By using different anode materials, these batteries could have an even greater energy density. One material, tin, has a theoretical lithium capacity (994 mAh/g) over three-times higher than commercial carbon anode materials. Unfortunately, to achieve this high capacity, bulk tin undergoes a large volume expansion, and the material pulverizes during cycling, giving a rapid capacity fade. To mitigate this issue, tin must be scaled down to the nano-level to take advantage of unique micromechanics at the nanoscale. Synthesis techniques for Sn nanoparticle anodes are costly and overly complicated for commercial production. A novel one-step process for producing carbon-coated Sn nanoparticles via spark plasma erosion (SPE) shows great promise as a simple, inexpensive production method. The SPE method, characterization of the resulting particles, and their high-capacity reversible electrochemical performance as anodes are described. With only a 10% addition of these novel SPE carbon-coated Sn particles, one anode composition demonstrated a reversible capacity of ~460 mAh/g, achieving the theoretical capacity of that particular electrode formulation. These SPE carbon-coated Sn nanoparticles are drop-in ready for present commercial lithium-ion anode processing and would provide a ~10% increase in the total capacity of current commercial lithium-ion cells.

25 ENERGY STORAGE↗
DOE OSTI2023

On the Electrochemical Properties of Carbon-Coated NaCrO 2 for Na-Ion Batteries

NaCrO 2 is a promising cathode for Na-ion batteries. However, further studies of the mechanisms controlling its specific capacities and cycle stability are needed for real-world applications in the future. This study reveals, for the first time, that the typical specific capacity of ~110 mAh/g reported by many researchers when the charge/discharge voltage window is set between 2.0 and 3.6 V vs. Na/Na + is actually controlled by the low electronic conductivity at the electrode/electrolyte interface. Through wet solution mixing of NaCrO 2 particles with carbon precursors, uniform carbon coating can be formed on the surface of NaCrO 2 particles, leading to unprecedented specific capacities at 140 mAh/g, which is the highest specific capacity ever reported in the literature with the lower and upper cutoff voltages at the aforementioned values. However, such carbon-coated NaCrO 2 with ultrahigh specific capacity does not improve cycle stability because with the specific capacity at 140 mAh/g the Na deintercalation during charge is more than 50% Na ions per formula unit of NaCrO 2 which leads to irreversible redox reactions. The insights from this study provide a future direction to enhance the long-term cycle stability of NaCrO 2 through integrating carbon coating and doping.

25 ENERGY STORAGE↗
DOE OSTI2024

Proof of Concept of Natural and Synthetic Antifouling Agents in Coatings

Marine biofouling, caused by the deposition and accumulation of marine organisms on submerged surfaces, represents a huge concern for the maritime industries and also contributes to environmental pollution and health concerns. The most effective way to prevent this phenomenon is the use of biocide-based coatings which have proven to cause serious damage to marine ecosystems. Several research groups have focused on the search for new environmentally friendly antifoulants, including marine and terrestrial natural products and synthetic analogues. Some of these compounds have been incorporated into marine coatings and display interesting antifouling activities caused by the interference with the biofilm-forming species as well as by the inhibition of the settlement of macroorganisms. This review highlights the proof-of-concept studies of emerging natural or synthetic antifouling compounds in coatings, from lab-made to commercial ones, performed between 2019 and 2023 and their results in the field or in in vivo laboratorial tests.

Pereira, Daniela↗
DOE OSTI2023

Investigating the Electromechanical Sensitivity of Carbon-Nanotube-Coated Microfibers

The piezoresistance of carbon nanotube (CNT)-coated microfibers is examined using diametric compression. Diverse CNT forest morphologies were studied by changing the CNT length, diameter, and areal density via synthesis time and fiber surface treatment prior to CNT synthesis. Large-diameter (30–60 nm) and relatively low-density CNTs were synthesized on as-received glass fibers. Small-diameter (5–30 nm) and-high density CNTs were synthesized on glass fibers coated with 10 nm of alumina. The CNT length was controlled by adjusting synthesis time. Electromechanical compression was performed by measuring the electrical resistance in the axial direction during diametric compression. Gauge factors exceeding three were measured for small-diameter (<25 μm) coated fibers, corresponding to as much as 35% resistance change per micrometer of compression. The gauge factor for high-density, small-diameter CNT forests was generally greater than those for low-density, large-diameter forests. A finite element simulation shows that the piezoresistive response originates from both the contact resistance and intrinsic resistance of the forest itself. The change in contact and intrinsic resistance are balanced for relatively short CNT forests, while the response is dominated by CNT electrode contact resistance for taller CNT forests. These results are expected to guide the design of piezoresistive flow and tactile sensors.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Source apportionment of soot particles and aqueous-phase processing of black carbon coatings in an urban environment

Abstract. The impacts of soot particles on climate and human health depend on the concentration of black carbon (BC) as well as the thickness and composition of the coating material, i.e., organic and inorganic compounds internally mixed with BC. In this study, the size-resolved chemical composition of BC-containing aerosol was measured using a high-resolution soot particle aerosol mass spectrometer (SP-AMS) during wintertime in Fresno, California, a location influenced by abundant combustion emissions and frequent fog events. Concurrently, particle optical properties were measured to investigate the BC absorption enhancement. Positive matrix factorization (PMF) analysis was performed on the SP-AMS mass spectral measurements to explore the sources of soot particles and the atmospheric processes affecting the properties of BC coatings. The analysis revealed that residential woodburning and traffic are the dominant sources of soot particles. Alongside primary soot particles originating from biomass burning (BBOABC) and vehicles (HOABC) two distinct types of processed BC-containing aerosol were identified: fog-related oxidized organic aerosol (FOOABC) and winter-background OOABC (WOOABC). Both types of OOABC showed evidence of having undergone aqueous processing, albeit with differences. The concentration of FOOABC was substantially elevated during fog events, indicating the formation of aqueous secondary organic aerosol (aqSOA) within fog droplets. On the other hand, WOOABC was present at a relatively consistent concentration throughout the winter and was likely related to the formation of secondary organic aerosol (SOA) in both the gas phase and aerosol liquid water. By comparing the chemical properties and temporal variations in FOOABC and WOOABC, we gain insights into the key aging processes of BC aerosol. It was found that aqueous-phase reactions facilitated by fog droplets had a significant impact on the thickness and chemical composition of BC coatings, thereby affecting the light absorption and hygroscopic properties of soot particles. These findings underscore the important role of chemical reactions occurring within clouds and fogs and influencing the climate forcing of BC aerosol in the atmosphere.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

“Green” Fabrication of High-performance Transparent Conducting Electrodes by Blade Coating and Photonic Curing on PET for Perovskite Solar Cells

This study presents an innovative material processing approach to fabricate transparent conducting electrodes (TCEs) on polyethylene terephthalate (PET) substrates using blade coating and photonic curing. The hybrid TCEs consist of a multiscale Ag network, combining silver metal bus lines and nanowires, overcoated by an indium zinc oxide layer, and then photonically cured. Blade coating ensures film uniformity and thickness control over large areas. Photonic curing, a non-thermal processing method with significantly lower carbon emissions, enhances the conductivity and transparency of the coated layers. Our hybrid TCEs achieve an average transmittance of (81 ± 0.4)% referenced to air ((90 ± 0.4)% referenced to the PET substrate) in the visible range, an average sheet resistance of (11 ± 0.5) Ω sq−1, and an average surface roughness of (4.3 ± 0.4) nm. We benchmark these values against commercial PET/TCE substrates. Mechanical durability tests demonstrate <3% change in resistance after 2000 bending cycles at a 1 in radius. The scalable potential of the hybrid TCE fabrication method is demonstrated by high uniformity and excellent properties in 7 in × 8 in large-area samples and by performing the photonic curing process at 11 m min−1. Furthermore, halide perovskite solar cells fabricated on these hybrid TCEs achieve average and champion power conversion efficiencies of (10.5 ± 1.0) % and 12.2%, respectively, and significantly outperform devices made on commercial PET/TCEs. This work showcases our approach as a viable pathway for high-speed “green” manufacturing of high-performance TCEs on PET substrates for flexible optoelectronic devices.

Bonner, Justin C↗
DOE OSTI2020

Hydrophilic, light active coating for membranes

A porous membrane provides enhanced filtration of pollutants and particles by coating the membrane with conformal thin films of doped titanium dioxide via atomic layer deposition or, alternatively, sequential infiltration synthesis. The membrane can either be organic or inorganic, and the doping of the membrane, usually with nitrogen, is an important feature that shifts the optical absorption of the TiO2 from the UV range into the visible-light range. This enables the use of lower energy light, including sunlight, to activate the photocatalytic function of the film. The coating described in the present invention is compatible with virtually any porous membrane and allows for precise tuning of the pore size with molecular precision. The present invention presents a new coating process and chemical structure that provides catalytic activity, strongly enhanced by light, to both mitigate fouling and break down various organic pollutants in the process stream.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Protective coating for lithium-containing electrode and methods of making the same

A lithium-containing electrode with a protective coating and lithium-containing electrochemical cells including the same are provided herein. The protective coating has a first layer including a first fluoropolymeric matrix and Li—F compounds and a second layer including a second fluoropolymeric matrix. Methods of preparing the protective coating on the lithium-containing electrode by applying a first fluoropolymer and/or a first fluoropolymer precursor and a second fluoropolymer and/or a second fluoropolymer precursor are also provided herein.

Xiao, Xingcheng↗