Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “casting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Microstructural evolution and intermetallic formation in Zn-3Mg (wt%) powder mixture processed by high-pressure torsion

Severe plastic deformation (SPD) techniques have been used extensively over the past 40 years for producing strong metals and alloys. High-pressure torsion (HPT) is one of the most promising SPD techniques for achieving high strength through nanoscale grain refinement and phase transformation. In this research, a mixture of pure zinc (Zn) and magnesium (Mg) powders, Zn-3Mg (wt%), was HPT-processed under a pressure of 6 GPa for 1, 5, 10, 20, and 30 turns at room temperature to achieve a high strength biodegradable material. In order to understand the effects of pre-consolidation on the resulting microstructure and hardness, HPT processing was performed on loose powders placed in the die and also on a pre-compacted powder mixture and the resulting HPT disks were characterized by X-ray diffraction, scanning electron microscopy, atom probe tomography, and Vickers microhardness. In both cases, the HPT disk microstructures contained nanoscale grains, and stable and metastable strain-induced intermetallics, but an unusual softening appeared at large shear strains. Grain size, grain morphology, and the formation of different intermetallics were analyzed to explain the unusual hardness distribution, and it was found that an inverse Hall-Petch relationship between hardness and grain size exists. It is suggested that thermally-activated phenomena such as grain boundary sliding contributed to the strain-induced softening of this nano-structured biomaterial due to its low melting point. Finally, the current results are compared with those for HPT-processed cast alloys and hybrids of the same composition.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Dispersion of high oxygen permeability ionomers in water-propanol solutions

There is a growing interest in high oxygen permeability ionomers (HOPI) for better-performing proton exchange membrane fuel cell (PEMFC) catalyst layers. In this study, we used small-angle x-ray scattering (SAXS) to analyze dispersions of two types of perfluorinated sulfonic acid (PFSA) ionomers and a HOPI in water and propanol solvents, at concentrations between 1 wt% and 15 wt%. HOPI dispersions exhibited the interference peak typical of ionomers; by separately fitting the peak and higher- q regions with several models, we demonstrated that HOPI aggregates have a closer average spacing than conventional PFSA ionomers, and smaller aggregate size when assuming a cylindrical geometry. By measuring conventional PFSA ionomers with two side chain lengths and several equivalent weights, we showed that these side chain parameters alone did not explain the differences in aggregate spacing or size. In addition, the pattern was present whether samples were prepared in a 50/50 water/propanol or a more propanol-rich mixture. As such, the structural differences of HOPI could be due to its different backbone monomer. A better understanding of the influence of the HOPI chemistry on dispersion properties could help explain the ink structure and drying characteristics of HOPI observed in prior work. Future study of ionomer-catalyst mixtures, such as measuring ionomer adsorption to carbon, would help elucidate the role of ionomer from ink formulation to the cast electrode.

Aquivion↗
DOE OSTI2023

Predicting rare events using neural networks and short-trajectory data

Estimating the likelihood, timing, and nature of events is a major goal of modeling stochastic dynamical systems. When the event is rare in comparison with the timescales of simulation and/or measurement needed to resolve the elemental dynamics, accurate prediction from direct observations becomes challenging. In such cases a more effective approach is to cast statistics of interest as solutions to Feynman-Kac equations (partial differential equations). Here, we develop an approach to solve Feynman-Kac equations by training neural networks on short-trajectory data. Our approach is based on a Markov approximation but otherwise avoids assumptions about the underlying model and dynamics. This makes it applicable to treating complex computational models and observational data. Additionally, we illustrate the advantages of our method using a low-dimensional model that facilitates visualization, and this analysis motivates an adaptive sampling strategy that allows on-the-fly identification of and addition of data to regions important for predicting the statistics of interest. Finally, we demonstrate that we can compute accurate statistics for a 75-dimensional model of sudden stratospheric warming. This system provides a stringent test bed for our method.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

π-Extension and chlorination of non-fullerene acceptors enable more readily processable and sustainable high-performance organic solar cells

Organic solar cells (OSCs) processed without halogenated solvents and complex treatments are essential for future commercialization. Herein, we report three novel small molecule acceptors (NFAs) consisting of a Y6-like core but with π-extended naphthalene with progressively more chlorinated end-capping groups and a longer branched chain on the Nitrogen atom. These NFAs exhibit good solubilities in non-chlorinated organic solvents, broad optical absorptions, close π-π stacking distances (3.63–3.84 Å), and high electron mobilities (~10 -3 cm 2 V -1 s -1 ). Further, the o-xylene processed and as-cast binary devices using PM6 as the donor polymer exhibit a PCE increasing upon progressive chlorination of the naphthalene end-capping group from 8.93% for YN to 14.38% for YN-Cl to 15.00% for YN-2Cl. Furthermore similarly processed ternary OSCs were fabricated by employing YN-Cl and YN-2Cl as the third component of PM6:CH1007 blends (PCE = 15.75%). Compared to all binary devices, the ternary PM6:CH1007:YN-Cl (1:1:0.2) and PM6:CH1007:YN-2Cl (1:1:0.2) cells exhibit significantly improved PCEs of 16.49% and 15.88%, respectively, which are among the highest values reported to date for non-halogenated solvent processed OSCs without using any additives and blend post-deposition treatments.

14 SOLAR ENERGY↗
DOE OSTI2021

Assessment of small mechanical wastewater treatment plants: Relative life cycle environmental impacts of construction and operations

Many slow growing and shrinking rural communities struggle with aging or inadequate wastewater treatment plants (WWTPs), and face challenges in constructing and operating such facilities. Although existing literature has provided insight into the environmental sustainability of large facilities, including both the construction and operational phases, these studies have not examined small, rural facilities treating less than 7,000 m 3 /d (1.8 MGD) of wastewater in adequate depth and breadth. In this study, a detailed inventory of the construction and operational data for 16 case studies of small WWTPs was developed to elucidate their environmental life cycle impacts. Conventional LCA framework was followed. The results show that the environmental impacts of both the construction and operational phases are considerable. Operational impacts are highly related to energy usage. Improving energy efficiency of a plant may reduce the environmental impacts related to operations. Construction impacts can vary considerably between facilities. Process-related factors (e.g., concrete and reinforcing steel used in basins) are typically sized using the design flow; thus much of the variability in construction impacts among plants stems from the non-process related infrastructure. Multiple regression analysis was used as an exploratory tool to identify which non-process related plant aspects contribute to the variable environmental impact of small WWTPs. These factors include aluminum, cast iron, and the capacity utilization ratio (defined as the ratio of average flow to design flow). Furthermore, industry practitioners should consider these factors when aiming to reduce the environmental impacts of a small WWTP related to construction. Scenario sensitivity analyses found that the environmental impact of construction became smaller with longer design life, and the end-of-life consideration does not heavily influence the environmental sustainability of a WWTP.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

Engineering grain boundary anisotropy to elucidate grain growth behavior in alumina

Current grain growth models have evolved to account for the relationship between grain boundary energy/mobility anisotropy and the five degrees of grain boundary character. However, the role of grain boundary networks on overall growth kinetics remains poorly understood. To experimentally investigate this problem, a highly textured Al 2 O 3 was fabricated by colloidal casting in a strong magnetic field to engineer a unique spatial distribution of grain boundary character. Microstructural evolution was quantified and compared to an untextured sample. From this comparison, a prevalence of (0001)/(0001) terminated grain boundaries with anisotropic networks were identified in the textured sample. These boundaries and their networks were found to be driving grain growth at a faster rate than predicted by models. These findings will allow better modelling of grain growth in real systems by experimentally exploring the impact thereon of grain boundary plane anisotropy and relative energy/mobility differences between neighboring boundaries.

36 MATERIALS SCIENCE↗
DOE OSTI2023

$In-situ$ synchrotron x-ray diffraction and thermal expansion of TiB2 up to ~3050 °C

There is an increasing interest in understanding the performance and properties of ultra-high temperature ceramics due to their high melting points (<3000 °C) that make them promising for extreme environment applications. In-situ high temperature X-ray diffraction experiments were performed on TiB 2 beads up to ~3050 °C. For these experiments, TiB 2 powders were fabricated into spherical beads via gel casting methods and densified in a high temperature graphite furnace. These sample beads were then levitated in a conical nozzle levitator with reducing atmosphere (3% H 2 -Ar) while being heated using a 400 W CO 2 laser. During levitation a collimated synchrotron X-ray source was used to perform in-situ, temperature-dependent structural characterizations. The anisotropic coefficients of thermal expansion of TiB 2 were characterized as a function of temperature up to ~3050 °C. Elucidation of these properties are critical for the advancement of TiB 2 ceramics and other transition metal di-borides for use in high temperature applications such as hypersonic platforms, nuclear reactors, and atmospheric re-entry.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Evaluating the bond strength and fracture mechanisms of cold-sprayed zinc coating on AZ91 magnesium substrate via a combined experimental and computational approach

Magnesium (Mg) alloys are ideal candidates for automotive applications due to their high strength to weight ratio, castability, recyclability etc., however, they lack corrosion and oxidation resistance. Solid-state deposition techniques, such as cold spray, have been demonstrated to enhance their corrosion resistance as it relies on the severe plastic deformation of powder particles upon impact with the substrate to form a metallurgical bond with the substrate and within the coating. At cold sprayed interfaces, a heterogeneous microstructure is formed that includes some porosity, oxides and intermetallics which can significantly affect coating performance. Thus, establishing a direct correlation between the interface microstructure and its properties can aid in designing optimal cold spray parameters. In this study, we investigated the microstructure and mechanical properties of a zinc (Zn) coating deposited on a high pressure die cast (HPDC) AZ91 Mg substrate via high resolution scanning transmission electron microscopy, in situ micro-tensile testing, and finite element method (FEM) modeling. Micro-tensile pillars fabricated using the plasma focused ion beam (PFIB) successfully isolates the coating-substrate interface within the gauge length. The average bond strength of Zn-Mg interface was determined to be ∼140 MPa with failure occurring partially at the interface and mostly into the coatings. A detailed microstructural characterization revealed evidence of a strong metallurgical bonding at the Zn-Mg interface and formation of the C14 MgZn 2 laves phase interlayer resulting in a mixed mode of fracture during the micro-tensile experiments. FEM modeling reveals the stress distribution along the interfaces and suggests that a MgZn 2 layer thickness between 200–400 nm is optimum to increase the bond strength and minimize the triaxiality. Such a site-specific interfacial analysis with correlative computational modeling provides crucial insight into the overall performance of cold spray interfaces.

Bond strength↗
DOE OSTI2025

Integrated process-structure–property–performance optimization of cold-sprayed zinc coatings on AZ91 magnesium alloy

High-pressure die cast (HPDC) AZ91 magnesium alloy is widely used in automotive components such as transmission housings and brackets for its excellent strength-to-weight ratio. Zinc-based cold spray coatings can be applied selectively to vulnerable areas to enhance corrosion resistance, minimize galvanic coupling with dissimilar metals, and eliminate the need for full-surface oxide coatings, making the process more efficient and targeted. A comprehensive evaluation of 16 combinations of nitrogen carrier gas temperatures and pressures led to the identification of an optimal range of process parameters, yielding Zn coatings with porosity <0.5 % by area, wear rates reduced by a factor of two compared to uncoated AZ91, and adhesion strengths up to 35 MPa. The enhanced mechanical performance of the coating is attributed to the low porosity and the formation of a metallurgical bond at the coating-substrate interface. Corrosion studies using macroscale potentiodynamic polarization (PDP) and electrochemical impedance spectroscopy (EIS) revealed a significant decrease in corrosion rate and a shift to more noble corrosion potentials (ZCP) for coated substrates. Furthermore, the Zn cold-sprayed samples exhibited significantly lower corrosion-induced evolved hydrogen content compared to the base AZ91 substrate and AZ91 coated with industrial coatings, demonstrating that the Zn layer effectively protects the substrate from the corrosive environment. Overall, cold spray Zn coatings significantly improve the mechanical and corrosion performance of AZ91 Mg alloys, addressing key material challenges and enabling their broader use in automotive applications.

Corrosion performance↗
DOE OSTI2023

Stress characterization for friction-stir-welded electric vehicle battery trays with application of neutron diffraction

The battery tray is an essential component that protects and controls battery-cell temperatures in electric and plug-in hybrid vehicles. The functional stress limit of the battery tray heavily depends on the residual stress acquired from the manufacturing process. Consequently, exceeding the stress limit of the battery tray during operation could compromise the battery-cell banks and may risk the vehicle's safety. Hence, understanding residual stress formation is vital for design and safety concerns. Here, in the current study, AA 6061-plates were friction stir welded to an A365 high-pressure die-cast battery tray to create sealed coolant channels in the battery tray. However, this multi-material lap friction stir weld introduces residual stress into the battery tray, resulting in distortion. This distortion was mitigated using burnishing or coining operations, though straightening the battery tray had initially unknown effects on the residual stress. Therefore, neutron diffraction was utilized to characterize residual stresses after straightening. The results indicate that the friction stir welding (FSW) operation generated residual stresses exceeding the yield strength of the material, consequently deforming the battery tray by ±3 mm from the pre-weld geometry. The burnishing operation reduced the residual stresses below the material's yield strength while restoring the tray to within ±0.75 mm of the pre-weld geometry. Similarly, the coining operation restored the battery tray to within ±0.75 mm of the pre-weld geometry, however, increasing the number of locations where the residual stress exceeds the yield strength of the material.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Structure and magnetism of AlCoCrCuFeNi high-entropy alloy

We report on the investigation of magnetic and structural properties of AlCoCrCuFeNi, which is known to crystallize in a dual phase solid solution: the face-centred cubic (FCC) or the body-centred cubic (BCC). The results of neutron (NPD) and synchrotron powder diffraction (SXRD) allow to partially resolve magnetic information coming from BCC and FCC phases, which is impossible in the bulk magnetic measurements. Electron diffraction (PED) revealed that AlCoCrCuFeNi forms dendritic microstructure with the Cu-rich FCC phase and the Ni-rich BCC phase. Lattice parameters obtained from PED method are in good agreement with parameters obtained after refinement on the basis of powder X-ray diffraction measurements. The local crystal and electronic structure around Co was studied using Co K X-ray Absorption Spectroscopy (XAS). The magnetic measurements show that AlCoCrCuFeNi reveal a ferromagnetic transition at about 330K and displays magnetic hysteresis loop at the room temperature. Results from NPD suggest that the magnetic moment is mostly located in the BCC subsystem. The alloy shows soft magnetic properties. Saturated magnetizations (M s ), remanence ratio (M r /M s ) and coercivity (H c ) of the cast are estimated to be 45.10emu/g, 5.1% and 56 Oe at 300K, respectively. Finally, the BCC-FCC phase transformation up to 673K (400°C) was investigated using temperature dependent NPD, where a possible second BCC phase was identified.

36 MATERIALS SCIENCE↗
DOE OSTI2021

On the implementation of dislocation reactions in continuum dislocation dynamics modeling of mesoscale plasticity

The continuum dislocation dynamics framework for mesoscale plasticity is intended to capture the dislocation density evolution and the deformation of crystals when subjected to mechanical loading. It does so by solving a set of transport equations for dislocations concurrently with crystal mechanics equations, with the latter being cast in the form of an eigenstrain problem. Incorporating dislocation reactions in the dislocation transport equations is essential for making such continuum dislocation dynamics predictive. A formulation is proposed to incorporate dislocation reactions in the transport equations of the vector density-based continuum dislocation dynamics. This formulation aims to rigorously enforce dislocation line continuity using the concept of virtual dislocations that close all dislocation loops involved in cross slip, annihilation, and glissile and sessile junction reactions. The addition of virtual dislocations enables us to accurately enforce the divergence free condition upon the numerical solution of the dislocation transport equations for all slip systems individually. A set of tests were performed to illustrate the accuracy of the formulation and the solution of the transport equations within the vector density-based continuum dislocation dynamics. Comparing the results from these tests with an earlier approach in which the divergence free constraint was enforced on the total dislocation density tensor or the sum of two densities when only cross slip is considered shows that the new approach yields highly accurate results. Bulk simulations were performed for a face centered cubic crystal based on the new formulation and the results were compared with discrete dislocation dynamics predictions of the same. The microstructural features obtained from continuum dislocation dynamics were also analyzed with reference to relevant experimental observations.

36 MATERIALS SCIENCE↗
DOE OSTI2025

High temperature tensile properties of H13 tool steel fabricated via binder jet additive manufacturing

H13 is one of the most used steels for hot work tooling applications like die casting. Binder jet additive manufacturing (BJAM) offers a cost-effective solution to fabricate tools with performance enhancing features like internal cooling channels. While full densification of BJAM H13 has been demonstrated in the literature, the room and high temperature tensile properties of the material, and the effect of post-process treatments like hot isostatic pressing (HIP), and heat treatment (HT) are unknown. Here we use HIP+HT to obtain a combination of ultimate tensile strength (UTS) and elongation to failure that is superior to H13 fabricated via laser powder bed fusion and wire arc additive manufacturing. HIP+HT BJAM H13 has a superior UTS (1836 MPa) compared with conventionally processed (1671 MPa) H13 but has lower plastic elongation. We report that as-sintered samples have an extensive network of continuous grain boundary (GB) carbides that contribute to brittle fracture. HIP+HT results in partial dissolution of GB carbides and formation of a fine martensitic microstructure resulting in superior tensile strength and elongation compared with as-sintered H13. We use thermo-kinetic calculations to rationalize the effects of HIP+HT on microstructure and properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tailoring grain growth and solid solution strengthening of single-phase CrCoNi medium-entropy alloys by solute selection

In the present study, we selected solutes to be added to the CrCoNi medium-entropy alloy (MEA) based on the mismatch of self-diffusion activation energy (SDQ) between the alloying elements and constituent elements of the matrix, and then investigated their grain growth behavior and mechanical properties. Mo and Al were selected as the solutes for investigation primarily because they have higher and lower SDQ, respectively, than those of the matrix elements; a secondary factor was their higher and lower shear modulus. Their concentrations were fixed at 3 at.% each because previous work had shown these compositions to be single-phase solid solutions with the face-centered cubic structure. Three alloys were produced by arc melting, casting, homogenizing, cold rolling and annealing at various temperatures and times to produce samples with different grain sizes. They were (a) the base alloy CrCoNi, (b) the base alloy plus 3 at.% Mo, and (c) the base alloy plus 3 at.% Al. The activation energies for grain growth of the CrCoNi, CrCoNi-3Mo and CrCoNi-3Al MEAs were found to be ~251, ~368 and ~219 kJ/mol, respectively, consistent with the notion that elements with higher SDQ (in this study Mo) retard grain growth (likely by a solute-drag effect), whereas those with lower values (Al) accelerate grain growth. The room-temperature tensile properties show that Mo increases the yield strength by ~40% but Al addition has a smaller strengthening effect consistent with their relative shear moduli. The yield strength as a function of grain size for the three singlephase MEAs follows the classical Hall-Petch relationship with much higher slopes (> 600 MPa μm -0.5 ) than traditional solid solutions. Furthermore, this work shows that the grain growth kinetics and solid solution strengthening of the CrCoNi MEA can be tuned by selecting solute elements that have appropriate diffusion and physical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Experimental assessment of antimony (Sb) in pure uranium for immobilizing fission product lanthanides

The use of fuel additives is one of the concepts to mitigate fuel cladding chemical interaction (FCCI) for metallic fuel because fission product lanthanides are expected to be immobilized by the additive. Antimony (Sb) has been discovered to be a good candidate in UZr fuel. The present study focuses on its mechanism for immobilization in pure uranium, U–4Sb alloy was fabricated to understand the Sb behavior, while U–4Sb–4Ce was fabricated to simulate the case when lanthanides are generated. Both of the as-cast and annealed samples were characterized by scanning electron microscope (SEM) and energy dispersive spectrometer (EDS). U–Sb precipitates are formed in U–4Sb alloy, while U–Sb and Ce–Sb were found in U–4Sb–4Ce alloy, thermal exposure does not change the Sb-precipitation morphologies or chemical composition. Furthermore, diffusion couple tests between those alloys and cladding materials (Fe or HT9) under 650 °C for 500 h were performed and analyzed using SEM/EDS. Diffusion couple tests demonstrate the reaction between cladding and uranium, while no reaction between Sb-precipitations and cladding materials was found.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

α-U and ω-UZr 2 in neutron irradiated U-10Zr annular metallic fuel

Here, to develop metallic fuel with ultra-high burnup of 30%-40%, an annular U-10Zr fuel with 55% smear density was fabricated through a casting route and irradiated at the Advanced Test Reactor at Idaho National Laboratory. The annular fuel design also serves as a demonstration of the feasibility to replace sodium bond with a helium bond to benefit the geological disposal of irradiated fuel, cut the cost of fuel fabrication, and boost the overall metallic fuel economy. This paper reports the results from transmission electron microscopy (TEM) based post-irradiation examination of this fuel type irradiated to a burnup of 3.3% fissions per initial heave metal atoms for initial screening purpose. After irradiation, the initial U-10Zr separated into an a-U annular region and an UZr 2+x center region with nanoscale spinodal decomposed microstructure. Because of the provided large amount of coherent interface areas, the fission gas atoms and vacancies generated in UZr 2+x phase are possibly pinned at the interface areas, leading to 20 times smaller fission gas bubbles than those in the neighboring a-U. The large bubbles in a-U become connected and merged into large pores that provide fast release paths for fission gas which prevents further fuel swelling. The fuel center still has open space to accommodate further fuel swelling from solid fission products at higher burnup. Other neutron irradiation induced phase and microstructure change are also characterized and compared with traditional solid fuel designs.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Out-of-pile and postirradiated examination of lanthanide and lanthanide-palladium interactions for metallic fuel

Palladium is being investigated as a fuel additive to bind with and potentially immobilize lanthanide fission products. A primary cause of fuel-cladding chemical interaction (FCCI) is the lanthanide fission products migrating to the fuel periphery and interacting with the cladding. This interaction will lead to wastage of the cladding and eventually to a cladding breach. Palladium has previously been identified as a promising additive used to prevent or decrease FCCI by reacting with the lanthanide fission products. In the current study, an alloy cast from the four highest abundant lanthanides found in irradiated metallic fuel, Nd, Ce, Pr, and La, with and without Pd, has been characterized using neutron diffraction, scanning electron microscopy, and electron probe microanalysis. In the lanthanide-Pd intermetallic compounds, all of the constituent compounds, i.e. Nd-Pd, Ce-Pd, La-Pd and Pr-Pd are known. There is very good agreement, both structurally and compositionally, between the out-of-pile lanthanide alloy and lanthanide fission products characterized in irradiated fuels. In both cases, the lanthanide elements form a solid solution in a hexagonal crystal structure. The out-of-pile lanthanide alloy follows Vegard's Law, with the measured and calculated (weighted average of constituents) lattice parameters being within 1% for both the a and c parameters. Pd bonds with the lanthanides (Ln) forming the phases LnPd and Ln7Pd3. The results indicate the properties of lanthanide compounds in irradiated metallic fuel can be reliably simulated in out-of-pile experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

In situ monitoring of microstructure evolution during thermal processing of uranium-zirconium alloys using laser-generated ultrasound

In this study, laser-generated ultrasound was used to monitor microstructure evolution during thermal processing of as-cast, polycrystalline binary uranium-zirconium metallic fuel alloys with compositions of U-20wt.%Zr (U-20Zr), U-50wt.%Zr (U-50Zr) and U-80wt.%Zr (U-80Zr). Ultrasonic waveforms were recorded during heating and cooling the samples from room temperature to >973 K and back. A phase transition temperature for all three compositions was estimated from the temperature at which an abrupt and rapid reduction in ultrasonic velocities was observed. Microstructural features on the length scale of tens of micrometers were inferred from the observation of scattering of ultrasonic waves by elastic heterogeneities above ~823 K in U-20Zr, while a hysteresis in the ultrasonic velocities of U-80Zr upon cooling was attributed to a partial retention of the high temperature phase following thermal annealing. The U-50Zr alloy exhibited a reversible viscoelastic response above 933 K, as evidenced by the observation of high frequency attenuation of the shear component of the waveforms at high temperature. Ultrasonic measurements were supplemented by in situ transmission electron microscopy (TEM). The TEM images revealed that the δ-U-Zr matrix in the three compositions underwent a spinodal decomposition above ~823 K into nanoscale regions. The ultrasonic measurements revealed larger, micron-scale structure evolution in the U-20Zr alloy at the same temperature. This large-scale structure is associated with heterogeneous regions having different Zr content. Our findings show the potential heating rate dependence of microstructural evolution in U-Zr alloys and highlight differences in the thermomechanical response and associated length scales during thermal annealing between single- and dual-phase compositions. These results demonstrate the utility of laser ultrasonics to rapidly and efficiently scan phase boundaries and monitor micrometer-scale structure evolution in metallic fuel alloys.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗