Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “backing layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

The role of buffer layer between TCO and p-layer in improving series resistance and carrier recombination of a-Si:H solar cells

The properties of the window layer and transparent conducting oxide (TCO)/p interface in silicon based thin-film solar cells are important factors in determining the cell efficiency. As the potential barrier got larger at the interface, the transmission of photo-generated holes were impeded and the recombination of photo-generated electrons diffusing back toward the TCO interface were enhanced leading to a deterioration of the fill factor. In this paper different p-layers were studied. It was found that using p-type hydrogenated amorphous silicon oxide (a-SiO{sub x}:H) layer as the window layer along with a 5 nm buffer layer which reduced the barrier at the fluorine doped tin oxide (SnO{sub 2}:F) TCO/p-layer interface, improved the cell efficiency. a-SiO{sub x}:H was used as the buffer layer. With the buffer layer between TCO and p-type a-SiO{sub x}:H, the potential barrier dropped from 0.506 eV to 0.472 eV. This lowered barrier results in increased short circuit current density (J{sub sc}) and fill factor (FF). With the buffer layer, J{sub sc} increased from 11.9 mA/cm{sup 2} to 13.35 mA/cm{sup 2} and FF increased from 73.22% to 74.91%.

36 MATERIALS SCIENCE↗

Substituted Quaternary Ammonium Salts Improve Low-Temperature Performance of Double-Layer Capacitors

Double-layer capacitors are unique energy storage devices, capable of supporting large current pulses as well as a very high number of charging and discharging cycles. The performance of doublelayer capacitors is highly dependent on the nature of the electrolyte system used. Many applications, including for electric and fuel cell vehicles, back-up diesel generators, wind generator pitch control back-up power systems, environmental and structural distributed sensors, and spacecraft avionics, can potentially benefit from the use of double-layer capacitors with lower equivalent series resistances (ESRs) over wider temperature limits. Higher ESRs result in decreased power output, which is a particular problem at lower temperatures. Commercially available cells are typically rated for operation down to only 40 C. Previous briefs [for example, Low Temperature Supercapacitors (NPO-44386), NASA Tech Briefs, Vol. 32, No. 7 (July 2008), p. 32, and Supercapacitor Electrolyte Solvents With Liquid Range Below 80 C (NPO-44855), NASA Tech Briefs, Vol. 34, No. 1 (January 2010), p. 44] discussed the use of electrolytes that employed low-melting-point co-solvents to depress the freezing point of traditional acetonitrile-based electrolytes. Using these modified electrolyte formulations can extend the low-temperature operational limit of double-layer capacitors beyond that of commercially available cells. This previous work has shown that although the measured capacitance is relatively insensitive to temperature, the ESR can rise rapidly at low temperatures, due to decreased electrolyte conductance within the pores of the high surface- area carbon electrodes. Most of these advanced electrolyte systems featured tetraethylammonium tetrafluoroborate (TEATFB) as the salt. More recent work at JPL indicates the use of the asymmetric quaternary ammonium salt triethylmethylammonium tetrafluoroborate (TEMATFB) or spiro-(l,l')-bipyrrolidium tetrafluoroborate (SBPBF4) in a 1:1 by volume solvent mixture of acetonitrile (AN) and methyl formate (MF) enables double-layer capacitor cells to operate well below -40 C with a relatively low ESR. Typically, a less than twofold increase in ESR is observed at -65 C relative to room-temperature values, when these modified electrolyte blends are used in prototype cells. Double-layer capacitor coin cells filled with these electrolytes have displayed the lowest measured ESR for an organic electrolyte to date at low temperature (based on a wide range of electrolyte screening studies at JPL). The cells featured high-surface-area (approximately equal to 2,500 m/g) carbon electrodes that were 0.50 mm thick and 1.6 cm in diameter, and coated with a thin layer of platinum to reduce cell resistance. A polyethylene separator was used to electrically isolate the electrodes.

Brandon, Erik J.↗

Effective photoelectric converters of ultraviolet radiation with graded-gap ZnS-based layers

The use of ultrathin ({approx}10 nm) stable p-Cu{sub 1.8}S films as a transparent component of the p-Cu{sub 1.8}S-n-ZnS heterojunction as well as of the graded-gap layers made it possible to obtain effective photoconverters of ultraviolet radiation. The results of examination of the properties of photoactive Cu{sub 1.8}S-ZnS junctions grown on the CdS or CdSe substrates with intermediate graded-gap layers CdS-Zn{sub x}Cd{sub 1-x}S or CdSe-(ZnS){sub x}(CdSe){sub 1-} {sub x}, respectively, are presented. With the correct selection of parameters of the substrates, the graded-gap layers allows one to attain the optimal characteristics of the p-n junction, to realize high electric fields at the Cu{sub 1.8}S-ZnS contact, and to solve the problem of fabrication of the back ohmic contact to ZnS without additional doping of all components of the heterostructure with a foreign impurity. Varying the thickness of a thin ZnS layer, it is possible to control the extension of the space charge in the graded-gap layer and thereby to control the long-wavelength edge of photoconverter sensitivity.

36 MATERIALS SCIENCE↗

Observation and Implications of Composition Inhomogeneity Along Grain Boundaries in Thin Film Polycrystalline CdTe Photovoltaic Devices

Abstract Leading photovoltaic technologies such as multicrystalline Si, CdTe, Cu(In,Ga)Se 2 , and lead halide perovskites are polycrystalline, yet achieve relatively high performance. At the moment polycrystalline photovoltaic technologies stand at a juncture where further advances in device performance and reliability necessitate additional characterization and modeling to include nanoscale property variations. Properties and implications of grain boundaries are previously studied, yet chemistry variations along individual grain boundaries and its implications are not yet fully explored. Here, the effects of bromine etching of CdTe absorber layers on the nanoscale chemistry are reported. Bromine etching is commonly used for improving CdTe back contacts, yet it removes both cadmium and chlorine along grain boundaries to depths closer to 1 µm. 2D device simulations reveal these composition modifications limit photovoltaic performance. Since grain boundaries and their intersections with surfaces and interfaces are universal to thin film photovoltaics, these findings call for similar studies in each of the photovoltaic technologies to further enable advances.

Misra, Sudhajit↗

Remnant PbI{sub 2}, an unforeseen necessity in high-efficiency hybrid perovskite-based solar cells?

Perovskite-containing solar cells were fabricated in a two-step procedure in which PbI{sub 2} is deposited via spin-coating and subsequently converted to the CH{sub 3}NH{sub 3}PbI{sub 3} perovskite by dipping in a solution of CH{sub 3}NH{sub 3}I. By varying the dipping time from 5 s to 2 h, we observe that the device performance shows an unexpectedly remarkable trend. At dipping times below 15 min the current density and voltage of the device are enhanced from 10.1 mA/cm{sup 2} and 933 mV (5 s) to 15.1 mA/cm{sup 2} and 1036 mV (15 min). However, upon further conversion, the current density decreases to 9.7 mA/cm{sup 2} and 846 mV after 2 h. Based on X-ray diffraction data, we determined that remnant PbI{sub 2} is always present in these devices. Work function and dark current measurements showed that the remnant PbI{sub 2} has a beneficial effect and acts as a blocking layer between the TiO{sub 2} semiconductor and the perovskite itself reducing the probability of back electron transfer (charge recombination). Furthermore, we find that increased dipping time leads to an increase in the size of perovskite crystals at the perovskite-hole-transporting material interface. Overall, approximately 15 min dipping time (∼2% unconverted PbI{sub 2}) is necessary for achieving optimal device efficiency.

36 MATERIALS SCIENCE↗

Surface processing for bulk niobium superconducting radio frequency cavities

The majority of niobium cavities for superconducting particle accelerators continue to be fabricated from thin-walled (2-4mm) polycrystalline niobium sheet and, as a final step, require material removal from the radio frequency (RF) surface in order to achieve performance needed for use as practical accelerator devices. More recently bulk niobium in the form of, single-or large-grain slices cut from an ingot has become a viable alternative for some cavity types. In both cases the so-called damaged layer must be chemically etched or electrochemically polished away. The methods for doing this date back at least four decades, however, vigorous empirical studies on real cavities and more fundamental studies on niobium samples at laboratories worldwide have led to seemingly modest improvements that, when taken together, constitute a substantial advance in the reproducibility for surface processing techniques and overall cavity performance. This article reviews the development of niobium cavity surface processing, and summarizes results of recent studies. We place some emphasis on practical details for real cavity processing systems which are difficult to find in the literature but are, nonetheless, crucial for achieving the good and reproducible cavity performance. New approaches for bulk niobium surface treatment which aim to reduce cost or increase performance, including alternate chemical recipes, barrel polishing and 'nitrogen doping' of the RF surface, continue to be pursued and are closely linked to the requirements for surface processing.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Charge-Order-Induced Ferroelectricity in LaVO 3 / Sr VO 3 Superlattices

In this paper, the structure and properties of the $1{\mathbin:}1$ superlattice of ${\mathrm{LaVO}}_{3}$ and ${\mathrm{SrVO}}_{3}$ are investigated with a first-principles density-functional-theory-plus-$U$ ($\mathrm{DFT}+U$) method. The lowest energy states are antiferromagnetic charge-ordered Mott-insulating phases. In one of these insulating phases, layered charge ordering combines with the layered La/Sr cation ordering to produce a polar structure with a large nonzero spontaneous polarization normal to the interfaces. This polarization, comparable to that of conventional ferroelectrics, is produced by electron transfer between the ${\mathrm{V}}^{3+}$ and ${\mathrm{V}}^{4+}$ layers. The energy of this normal-polarization state relative to the ground state is only 3 meV per vanadium. Under tensile strain, this energy difference can be further reduced, suggesting that the normal-polarization state can be induced by an electric field applied normal to the superlattice layers, yielding an antiferroelectric double-hysteresis loop. Finally, if the system does not switch back to the ground state on removal of the field, a ferroelectric-type hysteresis loop could be observed.

36 MATERIALS SCIENCE↗

Microstructure and property modifications of an AISI H13 (4Cr5MoSiV) steel induced by pulsed electron beam treatment

In the present work, surface modifications generated by the low energy high current pulsed electron beam (LEHCPEB) treatments have been investigated on an AISI H13 (4Cr5MoSiV) steel. From the observations of scanning electron microscopy, x-ray diffraction, and electron back scattering diffraction determinations, it could be established that the final structure in the melted layer is a mixture of ultrafine {delta} phase, martensite, and residual austenite. The formation of the heterogeneous microstructures on the surface layer is related to the very rapid heating, melting, solidification, and cooling induced by the LEHCPEB irradiation. After the LEHCPEB treatment, the wear resistance of the steel effectively improved. This can be mainly attributed to the higher hardness of the ultrafine structures formed on the top surface and the hardened subsurface layers after the treatment.

36 MATERIALS SCIENCE↗

MO-AB-BRA-07: Low Dose Imaging with Avalanche Amorphous Selenium Flat Panel Imager

Purpose: We present the first active matrix flat panel imager (AMFPI) capable of producing x-ray quantum noise limited images at low doses by overcoming the electronic noise through signal amplification by photoconductive avalanche gain (gav). The indirect detector fabricated uses an optical sensing layer of amorphous selenium (a-Se) known as High-Gain Avalanche Rushing Photoconductor (HARP). The detector design is called Scintillator HARP (SHARP)-AMFPI. This is the first image sensor to utilize solid-state HARP technology. Methods: The detector’s electronic readout is a 24 × 30 cm{sup 2} array of thin film transistors (TFT) with a pixel pitch of 85 µm. The HARP structure consists of a 15 µm layer of a-Se isolated from the high voltage (HV) and signal electrode by a 2 µm thick hole blocking layer and electron blocking layer, respectively, to reduce dark current. A 150 µm thick structured CsI scintillator with reflective backing and a fiber optic faceplate (FOP) was coupled to the semi-transparent HV bias electrode of the HARP structure. Images were acquired using a 30 kVp Mo/Mo spectrum typically used in mammography. Results: Optical sensitivity measurements demonstrate that gav = 76 ± 5 can be achieved over the entire active area of the detector. At a constant dose to the detector of 6.67 µGy, image quality increases with gav until the effective electronic noise is negligible. Quantum noise limited images can be obtained with doses as low as 0.18 µGy. Conclusion: We demonstrate the feasibility of utilizing avalanche gain to overcome electronic noise. The indirect detector fabricated is the first solid-state imaging sensor to use HARP, and the largest active area HARP sensor to date. Our future work is to improve charge transport within the HARP structure and utilize a transparent HV electrode.

60 APPLIED LIFE SCIENCES↗

Modeling of Structural-Acoustic Interaction Using Coupled FE/BE Method and Control of Interior Acoustic Pressure Using Piezoelectric Actuators

A coupled finite element (FE) and boundary element (BE) approach is presented to model full coupled structural/acoustic/piezoelectric systems. The dual reciprocity boundary element method is used so that the natural frequencies and mode shapes of the coupled system can be obtained, and to extend this approach to time dependent problems. The boundary element method is applied to interior acoustic domains, and the results are very accurate when compared with limited exact solutions. Structural-acoustic problems are then analyzed with the coupled finite element/boundary element method, where the finite element method models the structural domain and the boundary element method models the acoustic domain. Results for a system consisting of an isotropic panel and a cubic cavity are in good agreement with exact solutions and experiment data. The response of a composite panel backed cavity is then obtained. The results show that the mass and stiffness of piezoelectric layers have to be considered. The coupled finite element and boundary element equations are transformed into modal coordinates, which is more convenient for transient excitation. Several transient problems are solved based on this formulation. Two control designs, a linear quadratic regulator (LQR) and a feedforward controller, are applied to reduce the acoustic pressure inside the cavity based on the equations in modal coordinates. The results indicate that both controllers can reduce the interior acoustic pressure and the plate deflection.

Mei, Chuh↗

On Flowfield Periodicity in the NASA Transonic Flutter Cascade: Experimental Study - Part 1

An extensive study to improve flow uniformity and periodicity in the NASA Transonic Flutter Cascade is presented here. The results are reported in two independent parts dealing with the experimental approach and the analytical approach. The first part, the Experimental Study, focuses first on the data sets acquired in this facility in the past and explains several discrepancies, particularly the questions of actual flow incidence and cascade back pressure levels. Next, available means for control and modifications of the cascade flowfield, boundary layer bleed and tailboard settings are presented in detail. This is followed by experimental data sets acquired in modified test facility configurations that were based on analytical predictions of the cascade flowfield. Finally, several important conclusions about improving the cascade flowfield uniformity and blade load periodicity are summarized. The important conclusions are: (1) boundary layer bleed does not improve the cascade flow periodicity; (2) tunnel wall contours must be carefully matched to the expected shape of cascade streamlines; (3) actual flow incidence for each cascade configuration rather must be measured instead of relying on the tunnel geometry; and (4) the current cascade configuration exhibits a very high blade load uniformity over six blades from blade #2 to blade #7, and the facility is now ready for unsteady pressure data acquisition.

Lepicovsky, J.↗

In-SITU, Time-resolved Raman Spectro-micro-topography of an Operating Lithium Ion Battery

A Raman microscope has been coupled to a computer-controlled, two-dimensional linear translator attached to a custom-designed, sealed optical chamber to allow in situ acquisition of space-, and time-resolved spectra of an operating thin graphite/LiCoO2 Li-ion battery. This unique arrangement made it possible to collect continuously series of Raman spectra from a sharply defined edge of the battery exposing the anode (A), separator (S), and cathode (C), during charge and discharge, while the device was moved back and forth under the fixed focused laser beam along an axis normal to the layered A/S/C plane. Clear spectral evidence was obtained for changes in the amount of Li(+) within particles of graphite in the anode, and, to a lesser extent, of LiCoO2 in the cathode, during battery discharge both as a function of position and time. Analysis of time-resolved Raman spectro-micro-topography (SMT) measurements of the type described in this work are expected to open new prospects for assessing the validity of theoretical models aimed at simulating the flow of Li(+) within Li-ion batteries under operating conditions.

Luo, Yu↗

Amine Swingbed Payload Technology Demonstration

The Amine Swingbed is an amine-based, vacuum-regenerated adsorption technology for removing carbon dioxide and humidity from a habitable spacecraft environment, and is the baseline technology for the Orion Program’s Multi-Purpose Crew Vehicle (MPCV). It uses a pair of interleaved-layer beds filled with SA9T, the amine sorbent, and a linear multiball valve rotates 270° back and forth to control the flow of air and vacuum to adsorbing and desorbing beds. One bed adsorbs CO2 and H2O from cabin air while the other bed is exposed to vacuum for regeneration by venting the CO2 and H2O. The two beds are thermally linked, so no additional heating or cooling is required. The technology can be applied to habitable environments where recycling CO2 and H2O is not required such as short duration missions.

Sweterlitsch, Jeffrey↗

PVwindow (Photovoltaic Window Simulator) [SWR-22-01]

PVwindow simulates photovoltaic window properties by allowing the user build stacks of thin film materials that compose the window layers. The only needed inputs are the complex refractive indices and thicknesses of the materials. The software will simulate the optical transmission, front reflection, and back reflection of the stack using the transfer matrix method. Properties specific to PV window optics such as visible transmittance and color are also calculated. The optics code extracts the number of absorbed photons in the PV absorber layer and solves the single diode equation to yield theoretical photovoltaic metrics such as power conversion efficiency, fill factor, open circuit voltage, and short circuit current of the PV window when illuminated at an arbitrary angle or from either side of the stack. The software tool ultimately allows researchers to design photovoltaic windows and simulate their properties. The software also exports files that can be read into LBL Window software or into the EnergyPlus and Open Studio building energy modeling software to determine larger scale energy impacts of PV window integration.

Wheeler, Lance↗

Tropospheric Ozone Variability during LASIC Field Campaign Report

Part of the U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Climate Research Facility’s Layered Atlantic Smoke Interactions with Clouds (LASIC) field campaign. The primary goal of the measurements was to improve understanding of the evolution of the wave-one ozone maximum. The key objectives were Measure the variability of ozone mixing ratios associated with the African Easterly Jet (AEJ) on sub-synoptic time scales in which meteorology may play a role. In concert with weekly measurements from the Southern Hemisphere Additional Ozonesondes (SHADOZ) network, determine the vertical distribution of ozone and aerosols at Ascension Island. Determine from lidar measurements the locations of the biomass burning (BB layer) and its relationship to ozone mixing ratios. Determine the relative abundance of ozone in the BB layer relative to ozone mixing ratios at higher altitudes that may be associated with lightning nitrogen oxides (LNOx). Determine sources of high or low ozone mixing ratios through back trajectory models at Ascension Island.

LASIC field campaign, Ascension Island, biomass bu↗

Micromachined force-balance feedback accelerometer with optical displacement detection

An accelerometer includes a proof mass and a frame that are formed in a handle layer of a silicon-on-an-insulator (SOI). The proof mass is separated from the frame by a back-side trench that defines a boundary of the proof mass. The accelerometer also includes a reflector coupled to a top surface of the proof mass. An optical detector is located above the reflector at the device side. The accelerometer further includes at least one suspension spring. The suspension spring has a handle anchor that extends downwards from the device side to the handle layer to mechanically support upward and downward movement of the proof mass relative to a top surface of the proof mass.

42 ENGINEERING↗

X-ray absorption spectroscopy of lithium insertion and de-insertion in copper birnessite nanoparticle electrodes

The combination of ex situ X-ray diffraction (XRD) and X-ray absorption spectroscopy (XAS) measurements on 2D layered copper birnessite cathode materials for lithium ion battery applications provides detailed insight into both bulk-crystalline and localized atomic structural changes resulting from electrochemically driven lithium insertion and de-insertion. Copper birnessite electrodes that had been galvanostatically discharged and charged were measured with XRD to determine the accompanying long-range crystalline structure changes, while Mn and Cu K-edge XAS measurements provided a detailed view of the Mn and Cu oxidation state changes along with variations of the local neighboring atom environments around the Mn and Cu centers. While not detectable with XRD spectra, through XAS measurements it was determined that the copper ions (Cu 2+ ) are reduced to form amorphous nano-sized Cu metal, and can be oxidized back to Cu 2+ . In this work, the reversible nature of the interconversion provides a rationale to the enhanced discharge capacity of copper birnessite relative to the analogous copper-free birnessite materials. The manganese oxide octahedra comprising the 2D layers in the original copper birnessite crystal structure disperse during lithium insertion, and revert back close to their original orientation after lithium de-insertion. During electrochemical oxidation or reduction the layered birnessite structure does not collapse, even though significant local disordering around Mn and Cu centers is directly observed.

25 ENERGY STORAGE↗