Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Upgrade”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Pixel sensors with slim edges and small pitches for the CMS upgrades for HL-LHC

Here, planar n-in-n silicon detectors with small pitches and slim edges are being investigated for the innermost layers of tracking devices for the foreseen upgrades of the LHC experiments. Sensor prototypes compatible with the CMS readout, fabricated by Sintef, were tested in the laboratory and with a 120 GeV/c proton beam at the Fermilab test beam facility before and after irradiation with up to 2 × 10 15 neq/cm 2 fluence. Preliminary results of the data analysis are presented.

43 PARTICLE ACCELERATORS↗

Progress in reducing ICRF-specific impurity release in ASDEX upgrade and JET

Use of new 3-strap ICRF antennas with all-tungsten (W) limiters in ASDEX Upgrade results in a reduction of the W sources at the antenna limiters and of the W content in the confined plasma by at least a factor of 2 compared to the W-limiter 2-strap antennas used in the past. The reduction is observed with a broad range of plasma shapes. In multiple locations of antenna frame, the limiter W source has a minimum when RF image currents are decreased by cancellation of the RF current contributions of the central and the outer straps. In JET with ITER-like wall, ITER-like antenna produces about 20% less of main chamber radiation and of W content compared to the old A2 antennas. However the effect of the A2 antennas on W content is scattered depending on which antennas are powered. Experiments in JET with trace nitrogen (N 2 ) injection show that a presence of active ICRF antenna close to the midplane injection valve has little effect on the core N content, both in dipole and in -90° phasing. This indicates that the effect of ICRF on impurity transport across the scape-off-layer is small in JET compared to the dominant effect on impurity sources leading to increased impurity levels during ICRF operation.

1CRF↗

Analyzing the impact of reaction models on the production of hydrocarbons from thermally upgraded oil shales

Reaction parameters significantly affect oil production from shales by means of heating and in-situ upgrading. In this work, we perform numerical simulations of two chemical reaction models, which are mainly used in the research of kerogen pyrolysis and subsequent hydrocarbon decomposition in organic-rich porous media. They are the Braun and Burnham model and Wellington model. In these forward numerical simulations, we present the influence of the two reaction models on hydrocarbon production. The Braun and Burnham reaction model shows more vigorous kerogen and subsequent decomposition reactions and more hydrocarbon production than the Wellington model. A local sensitivity analysis identifies the reaction parameters with the highest influence on productivity, and the most sensitive outputs. A data-worth analysis identifies the most valuable observation data to be measured for the best prediction of total hydrocarbon production. We find that the most valuable observation data is the cumulative production of heavy oil in the Braun and Burnham model and of light oil in the Wellington model, respectively. Finally, once we determine the maximum allowable prediction uncertainty and the expected measurement uncertainty, the observation data to be measured for the minimization of prediction uncertainty can be obtained.

04 OIL SHALES AND TAR SANDS↗

Modeling the Kinetics of Deactivation of Catalysts during the Upgrading of Bio-Oil

The fouling of catalysts for the upgrading of bio-oils appears to be very different from the fouling of catalysts for the hydroprocessing of petroleum-derived streams. There are two reasons for the differences: a) bio-oil contains polarizable components and phases that can stabilize reaction intermediates exhibiting charge separation and b) bio-oil components contain functional groups that contain O, notably carbonyls (>C=O). Aldol condensation of carbonyls affords very different pathways for the production of oligomeric, refractory deposits than does dehydrogenation/polymerization of petroleum-derived hydrocarbons. Colloquially, we refer to the bio-oil derived deposits as “gunk” to discriminate them from coke, the carbonaceous deposits encountered in petroleum refining. Classical gelation, appears to be a suitable model for the “gunking” reaction. Our work has helped explain the temperature range at which bio-oil should be pre-processed (“stabilized”) to confer longer lifetimes on the catalysts used for more severe processing. Stochastic modeling (kinetic Monte Carlo simulations) appears suitable to capture the rates of oligomerization of bio-oil. This work was supported by the US Department of Energy, Office of Energy Efficiency and Renewable Energy, Bioenergy Technologies Office. Pacific Northwest National Laboratory (PNNL) is a multiprogram national laboratory operated for DOE by Battelle.

bio-oil upgrading↗

Nonlinear excitation of energetic particle driven geodesic acoustic mode by resonance overlap with Alfvén instability in ASDEX Upgrade

The Alfvén instability nonlinearly excited the energetic-particle-driven geodesic acoustic mode on the ASDEX-Upgrade tokamak, as demonstrated experimentally. The mechanism of the energetic-particle-driven geodesic acoustic mode excitation and the mode nonlinear evolution is not yet fully understood. In the present work, a first-principles simulation using the MEGA code investigated the mode properties in both the linear growth and nonlinear saturated phases. Here we show that the simulation successfully reproduced the excitation and coexistence of these two modes, and agreed with the experimental results well. Conclusive evidence showed that the resonance overlap is the excitation mechanism of the energetic-particle-driven geodesic acoustic mode. In the linear growth phase, energetic particles that satisfied different resonance conditions excited the Alfvén instability, which then caused energetic particle redistribution in phase space. These redistributed energetic particles caused resonance overlap, exciting the energetic-particle-driven geodesic acoustic mode in the nonlinear phase.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Comparative study of the dust particle population sampled during four consecutive campaigns in full-tungsten ASDEX Upgrade

Scanning electron microscopy images and energy-dispersive x-ray spectra were recorded for a total of about 4 x 10{sup 4} dust particles collected on the same position within the vacuum vessel via silicon wafers during four consecutive full-tungsten first wall campaigns of ASDEX Upgrade between 2007 and 2009. By careful analysis of the elemental composition and shape of the sampled particles, seven statistically relevant classes of dust were identified. The particle flux and area coverage of each class were normalized to the total plasma duration of each sampling period, revealing a high sensitivity of the dust composition to device conditioning. According to the present results, particles produced by arcing on divertor tiles with delaminated coatings were transported to the main chamber first wall.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Initial operation of the NSTX-Upgrade real-time velocity diagnostic

A real-time velocity (RTV) diagnostic based on active charge-exchange recombination spectroscopy is now operational on the National Spherical Torus Experiment-Upgrade (NSTX-U) spherical torus (Menard et al 2012 Nucl. Fusion 52 083015). We designed the system in order to supply plasma velocity data in real time to the NSTX-U plasma control system, as required for the implementation of toroidal rotation control. Our measurements are available from four radii at a maximum sampling frequency of 5 kHz. Post-discharge analysis of RTV data provides additional information on ion temperature, toroidal velocity and density of carbon impurities. Furthermore, examples of physics studies enabled by RTV measurements from initial operations of NSTX-U are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Near- and far scrape-off layer transport studies in detached, small-ELM ASDEX Upgrade discharges by means of EMC3-EIRENE

We compare various diagnostics characterizing an ASDEX Upgrade upper single-null discharge to EMC3-EIRENE simulations now including volumetric recombination and main chamber plasma-wall interaction but not yet drifts. The discharge is in a small-ELM regime and is approaching detachment due to a density ramp and nitrogen seeding. Time/ELM averaged upstream density, electron and ion temperature measurements as well as downstream ion saturation current, electron temperature and power flux measurements match the simulation within the error bars before and after reaching detachment, qualifying the code for this regime. Although the Ion Cyclotron Resonance Heating (ICRH) antenna limiters are 35 mm away from the separatrix, i.e. ten times the typical near-SOL power fall-off length $\lambda^{near}_q\ =\ $3.8 mm, they receive power fluxes of several hundreds of kW exceeding the ones to the outer target in the detached phase and strongly contribute to the particle fueling. This is explained by a substantially larger far-SOL power fall-off length $\lambda^{far}_q\ =\ $25 mm possibly caused by the small ELMs in the detached phase and the occurrence of a density shoulder.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Validation of high-fidelity ion cyclotron range of frequencies antenna coupling simulations in full 3D geometry against experiments in the ASDEX Upgrade tokamak

We address the validation of finite elements ion cyclotron range of frequencies (ICRF) antenna coupling simulation against experiments performed in the ASDEX Upgrade tokamak. Measurements of the loading resistance in ICRF-heated, magnetically-perturbed 3D plasma discharges are compared against numerical predictions of the RAPLICASOL code. To this end, the 3D induction field and the 3D density profile are modeled by concatenating the PARVMEC, BMW and EMC3-EIRENE codes. The 3D density is input to RAPLICASOL, where full-wave simulations are performed on a finite element mesh retaining full 3D geometry in the ICRF antenna model and the plasma description. The results are further compared with RAPLICASOL simulations using a 1D density profile as measured at the outboard midplane in the same experiments. We find that simulations using a 1D density profile overestimate the change in loading resistance by a factor of ~197 -248%, while simulations using the full 3D density profile are in agreement with experiments within a factor ~16%.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Scenario optimization for the tokamak ramp-down phase in RAPTOR: Part A. Analysis and model validation on ASDEX Upgrade

We discuss how the combination of experimental observations and rapid modeling has enabled to improve understanding of the tokamak ramp-down phase in ASDEX Upgrade. A series of dedicated experiments has been performed, to disentangle the effect of individual actuators like plasma current, auxiliary heating and plasma shaping. Optimized discharge termination strategies with increased margin with respect to radiative and vertical stability limits are proposed and tested in experiment. Radiative collapse of the edge $T$ $e$ profile after the HL back-transition is avoided by initially maintaining auxiliary heating during L-mode, showing beneficial effects even after the auxiliary heating is turned off. The capability of the RAPTOR code to model the time evolution of the internal inductance $\ell$ $i3$ has been validated, including the effect of a change in the $I$ $p$ ramp-down rate and the HL transition timing. The reduction of $\ell$ $i3$ caused by rapid compression of the plasma cross-section has been quantitatively recovered in simulations. Successful modeling of the $\ell$ $i3$ time evolution is essential to optimize ramp-down scenarios for future fusion reactors, for which vertical stability and power balance control will be more challenging.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Benign termination of runaway electron beams on ASDEX Upgrade and TCV

Abstract This paper discusses the development of a benign termination scenario for runaway electron (RE) beams on ASDEX Upgrade and TCV. A systematic study revealed that a low electron density (n e ) companion plasma was required to achieve a large MHD instability, which expelled the confined REs over a large wetted area and allowed for the conversion of magnetic energy to radiation. Control of the companion plasma n e was achieved via neutral pressure regulation and was agnostic to material injection method. The neutral pressure required for recombination was found to be dependent on impurity species, quantity and RE current. On TCV,n e increased at neutral pressures above 1 Pa, indicating that higher collisionality between the REs and neutrals may lead to an upper pressure limit. The conversion of magnetic energy to radiated energy was measured on both machines and a decrease in efficiency was observed at high neutral pressure on TCV. The benign termination technique was able to prevent any significant increase in maximum heat flux on AUG from 200 to 600 kA of RE current, highlighting the ability of this approach to handle fully formed RE beams.

Physics↗

ELM-free H-mode phase and decoupling of peeling–ballooning stability boundary in the MAST Upgrade tokamak

A linear magnetohydrodynamic (MHD) peeling–ballooning stability analysis of the edge-localized mode (ELM)-free phase of a MAST Upgrade (MAST-U) H-mode plasma is presented. In contrast to other similar discharges, #47018 is found to have a significantly higher and wider pedestal during its ELM-free H-mode phase that lasts for approximately 80 ms; this is made possible by the reduced core MHD mode activity on the q = 2 surface. During this period, there is sustained decoupling of peeling and ballooning branches of the stability boundary on J–α space, opening an access channel to the second stability regime with higher peaks in pedestal current density $J_{\mathrm{N,ped}}$ and pressure gradient (α). Such decoupling of the stability boundary has not previously been observed in MAST-U H-modes, and if such a condition can be readily reproduced, it opens a wide range of opportunities for MAST-U to explore low-collisionality peeling-limited pedestal regimes as well as advanced scenarios such as quiescent H-modes that are relevant to future reactors such as STEP and ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Charge-exchange losses of beam ions in MAST Upgrade: experiments and modelling

Dedicated experiments were performed on MAST Upgrade to study beam-ion losses caused by charge exchange (CX) with edge neutrals. The fuelling was switched from the high-field side to the low-field side mid-discharge. Direct measurements suggest a strong increase in the neutral density around the plasma and a decrease in the beam-ion density, which is qualitatively explained by CX losses. Measurements by a resistive bolometer have suggested particle bombardment during neutral beam injection, providing a unique opportunity to separate CX from other loss mechanisms. To verify and quantify CX losses, the orbit-following code ASCOT, which accounts both for CX neutralization and reionization, was used to simulate beam-particle power loads on the bolometer. Simulations reproduce measured bolometer power loads during high-field-side fuelling, verifying CX losses of approximately 10% of the off-axis beam power. Toroidally symmetric simulations overestimate power loads on the bolometer during low-field-side fuelling, which is explained by toroidal asymmetry in the neutral density distribution, as is demonstrated by toroidally asymmetric simulations. Results suggest significantly higher CX losses during low-field-side fuelling, up to about 50% of off-axis beam power.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experimental conditions to suppress edge localised modes by magnetic perturbations in the ASDEX Upgrade tokamak

For this, access conditions for full suppression of Edge Localised Modes (ELMs) by Magnetic Perturbations (MP) in low density high confinement mode (H-mode) plasmas are studied in the ASDEX Upgrade tokamak. The main empirical requirements for full ELM suppression in our experiments are: 1. The poloidal spectrum of the MP must be aligned for best plasma response from weakly stable kink-modes, which amplify the perturbation, 2. The plasma edge density must be below a critical value, 3.3 × 10 19 m -3 . The edge collisionality is in the range v $*\atop{i}$ = 0.15 - 0.42 (ions) and v $*\atop{e}$ = 0.15 - 0.25 (electrons). However, our data does not show that the edge collisionality is the critical parameter that governs access to ELM suppression. 3. The pedestal pressure must be kept sufficiently low to avoid destabilisation of small ELMs. This requirement implies a systematic reduction of pedestal pressure of typically 30% compared to unmitigated ELMy H-mode in otherwise similar plasmas. 4. The edge safety factor q 95 lies within a certain window. Within the range probed so far, q 95 = 3.5 - 4.2, one such window, q 95 = 3.57-3.95 has been identified. Within the range of plasma rotation encountered so far, no apparent threshold of plasma rotation for ELM suppression is found. This includes cases with large cross field electron flow in the entire pedestal region.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Active conditioning of ASDEX Upgrade tungsten plasma-facing components and discharge enhancement through boron and boron nitride particulate injection

The injection of boron (B) and boron nitride (BN) powders into ASDEX Upgrade H-mode discharges have demonstrated effective control of tungsten influx in low density/collisionality operational regimes, similar to conventional boronization methods. Sub-mm powder particles are gravitationally accelerated into the upper edge of a lower single null H-mode plasma with a boundary shape roughly conforming to the shape of the poloidal midplane limiters. Visible spectroscopy measurements at one of the outer limiter showed increases in both B and N signal levels, as well as elevated B levels in the divertor, and an increase in total radiated power by greater than a factor of two during BN injection. Globally the BN injection improved energy confinement by 10%–20%, associated with improvements in pedestal performance similar to gaseous N injection. Following conditioning discharges with B powder injection, three low gas-fueling discharges with magnetic perturbations for ELM suppression were successfully conducted. Furthermore, these first results suggest that the application of B containing powders can be used to both improve plasma performance in real-time, and to improve overall wall conditions for subsequent discharges.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Turbulence driven widening of the near-SOL power width in ASDEX Upgrade H-Mode discharges

Divertor heat flux data from infra red (IR) from various tokamaks in H-Mode regime show that the power width, $\lambda_{q}$, scales approximately like 1.6 $(R/a) ρ_{s,pol}$. However, the IR based scaling comes with the restriction that only discharges were considered with attached divertor conditions. Here we set up a new data base covering low edge density data but also including high density plasmas reaching the H-mode density limit. We use Thomson-scattering to measure the electron temperature decay length which will set the near-SOL power width through parallel heat conduction. We present scaling results for the density, temperature and pressure separatrix fall-off lengths. As the principal result we derive a generalized power width scaling which reads as $\lambda_{q}\propto\,\rho_{s,pol}\cdot(1+2.1\alpha_{t}^{1.7})$ where $\alpha_{t}$ describes a normalized collisionality ($\alpha_{t} = 3\cdot\,10^{-18}\,R\,q^2\,n\,Z_{eff}T^{-2}$). The parameter $\alpha_{t}$ describes the relative importance of the interchange effect on drift-wave turbulence as proposed by Scott and is found to be closely linked to the diamagnetic parameter αd introduced by Rogers, Drake and Zeiler (RDZ). The edge operational space for ASDEX Upgrade displays a boundary qualitatively in agreement with the region labelled as density limit in the edge plasma phase space proposed by RDZ. The data base shows in the limit of low edge densities ($\alpha_{t}\simeq\,0.2$) accurate agreement to the IR based power width scaling. At elevated separatrix densities ($\alpha_{t}\simeq\,1$) the power width is broadened by a factor of up to about three accompanied by a reduction of the $\text{H}_{98,y2}$ confinement factor. Finally, plasmas with higher triangularity show higher values for $\text{H}_{98,y2}$ in the same range of normalized collisionality.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Progress from ASDEX Upgrade experiments in preparing the physics basis of ITER operation and DEMO scenario development

An overview of recent results obtained at the tokamak ASDEX Upgrade (AUG) is given. A work flow for predictive profile modelling of AUG discharges was established which is able to reproduce experimental H-mode plasma profiles based on engineering parameters only. In the plasma center, theoretical predictions on plasma current redistribution by a dynamo effect were confirmed experimentally. For core transport, the stabilizing effect of fast ion distributions on turbulent transport is shown to be important to explain the core isotope effect and improves the description of hollow low-Z impurity profiles. The L–H power threshold of hydrogen plasmas is not affected by small helium admixtures and it increases continuously from the deuterium to the hydrogen level when the hydrogen concentration is raised from 0 to 100%. One focus of recent campaigns was the search for a fusion relevant integrated plasma scenario without large edge localised modes (ELMs). Results from six different ELM-free confinement regimes are compared with respect to reactor relevance: ELM suppression by magnetic perturbation coils could be attributed to toroidally asymmetric turbulent fluctuations in the vicinity of the separatrix. Stable improved confinement mode plasma phases with a detached inner divertor were obtained using a feedback control of the plasma β. The enhanced D α H-mode regime was extended to higher heating power by feedback controlled radiative cooling with argon. The quasi-coherent exhaust regime was developed into an integrated scenario at high heating power and energy confinement, with a detached divertor and without large ELMs. Small ELMs close to the separatrix lead to peeling-ballooning stability and quasi continuous power exhaust. Helium beam density fluctuation measurements confirm that transport close to the separatrix is important to achieve the different ELM-free regimes. Based on separatrix plasma parameters and interchange-drift-Alfvén turbulence, an analytic model was derived that reproduces the experimentally found important operational boundaries of the density limit and between L- and H-mode confinement. Feedback control for the X-point radiator (XPR) position was established as an important element for divertor detachment control. Stable and detached ELM-free phases with H-mode confinement quality were obtained when the XPR was moved 10 cm above the X-point. Investigations of the plasma in the future flexible snow-flake divertor of AUG by means of first SOLPS-ITER simulations with drifts activated predict beneficial detachment properties and the activation of an additional strike point by the drifts.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

I-mode pedestal relaxation events in the Alcator C-Mod and ASDEX Upgrade tokamaks

Abstract In some conditions, I-mode plasmas can feature pedestal relaxation events (PREs) that transiently enhance the energy reaching the divertor target plates. To shed light on their appearance, characteristics and energy reaching the divertor targets, a comparative study between two tokamaks — Alcator C-Mod and ASDEX Upgrade — is carried out. It is found that PREs appear only in a subset of I-mode discharges, mainly when the plasma is close to the H-mode transition. Also, a growing oscillating precursor before the PRE onset is observed in the region close to the separatrix in both devices, and a discussion on a possible triggering mechanism is outlined. The PRE relative energy loss from the confined region is found to increase with decreasing pedestal top collisionality ν ped * . Similarly, also the relative electron temperature drop at the pedestal top, which is related to the conductive energy loss, rises with decreasing ν ped * . Based on these relations, the PRE relative energy loss in future devices such as DEMO and ARC is estimated. Finally, the divertor peak energy fluence due to the PRE is measured on each device. Those values are then compared to the model introduced in Eich et al (2017 Nucl. Mater. Energy 12 84–90) for type-I edge localized modes. The model is shown to provide an upper boundary for PRE energy fluence data, while a lower boundary is found by dividing the model by three. These two boundaries are used to make projections of the PRE divertor energy fluence to DEMO and ARC.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗