Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Surface Power”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Foreword Special issue on the Kilopower Project, Kilowatt Reactor Using Stirling TechnologY (KRUSTY) Test

This special issue of Nuclear Technology contains full-length, peer-reviewed papers describing the design work leading up to and the results of the Kilowatt Reactor Using Stirling TechnologY (KRUSTY) test. KRUSTY was the centerpiece of the National Aeronautics and Space Administration (NASA) Kilopower Project to design, build, and test a space nuclear reactor. This test was the first such test since the end of the Space Nuclear Auxiliary Power (SNAP) project at the end of the 1960s. In this issue, the introduction paper presents the goals of the Kilopower Project and the potential missions this reactor concept could serve in NASA. Kilopower was intended to serve both human exploration needs on planetary surfaces as well as science needs for deep-space exploration. The design work for the experiment by Poston and the power conversion development by Gibson present the pre-work required to perform the eventual KRUSTY test. A paper on regulatory analysis follows, to show the path used to gain approval of the proposed experiment. Then, the early zero-power critical experiments are presented by Sanchez and Grove. These experiments were essential data used to enhance model predictions prior to the high-temperature test. Next, Poston presents the three experiments (warm criticals) that increase the temperature in an incremental fashion prior to the final experiment. These experiments were used to achieve final regulatory approval of the final high-temperature experiment. The last paper by Poston presents the results of the steady-state and transient testing of the reactor at full power and at the design temperature. These results show that the reactor design and as-built experiment met all of the requirements that NASA had developed for the system. Any experiment of this magnitude was accomplished only because of the hard work and dedication of a large number of people at multiple institutions, including the NASA Glenn Research Center, NASA Marshall Space Flight Center, Y-12 National Security Site, Los Alamos National Laboratory, and the Nevada National Security Site prime contractor (formerly National Security Technologies and now the Mission Support and Test Services). The project was jointly funded by the Space Technology Mission Directorate at NASA and the Criticality Safety Program at the National Nuclear Security Administration (NNSA). A special thanks to Jerry McKamy and Angela Chambers at the NNSA and Lee Mason and Don Palac at NASA for their support and guidance. For the authors and multitude of staff that performed this work, the passion for space nuclear reactors was the key to making this experiment a reality.

99 GENERAL AND MISCELLANEOUS↗

Statistical characterization of high voltage vacuum surface flashover with gapped and ungapped anodes

This manuscript reports the experimental study of a novel vacuum high-voltage (HV) feedthrough geometry with a recessed anode triple junction (ATJ) relevant to large-scale pulsed power systems. It is shown experimentally that introducing a vacuum gap between the insulator–anode interface and recessing the ATJ farther away from the cathode triple junction significantly enhances high voltage (HV) vacuum surface flashover hold-off. The results for “first pulse” and “consecutive pulse” tests are reported. The physical mechanisms contributing to the electrical failure of this feedthrough geometry appear to be unique to this geometry. These findings show the potential to allow for HV vacuum surface flashover geometries with significantly improved electrical characteristics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Data-Driven Cyber-Attack Detection for PV Farms via Time-Frequency Domain Features

The internetworking of grid-connected power electronics converters (PECs) in photovoltaic (PV) farms has inevitably expanded the cyber-attack surfaces. Here this paper presents a comprehensive study on cyber-attack detection and diagnosis for PEC-enabled PV farms via single waveform sensor to distinguish between normal conditions, open-circuit faults, short-circuit faults, and cyber-attacks. To our knowledge, this has not been attempted before. Firstly, we propose frequency-domain magnitude-based residuals to identify short-circuit faults and a time-domain mean current vector-based feature to distinguish open-circuit faults from other threats. These features can fully reflect the specific physical characteristics of PV farms during threat duration. Secondly, unlike micro phasor measurement units (µPMU) and raw electric waveform-based methods, the proposed innovative features can address novel cyber-attacks that are excluded from the training process. Thirdly, an online hardware-in-the-loop (HIL) testbed using the OPAL-RT real-time digital simulator has verified the effectiveness. The monitoring system runs in real-time while using HIL as an operational solar farm and a National Instruments (NI) data acquisition card as the electric waveform sensor at the point of coupling.

42 ENGINEERING↗

Advanced Diagnostics of Broad Spectrum Multipactor

Multipactor is a resonance event between electron emission and RF fields causing exponential secondary electron re-emission growth when the secondary electron yield of the primary electron impact energy exceeds unity. Multipactor is a serious problem in vacuum electron devices (VEDs) such as particle accelerators, radars, electronic warfare systems, directed energy devices, and even Hall effect thrusters. It also poses an even greater threat to space communication systems where high power, multi-channel links are required. The UC Davis and SLAC team will conduct basic research to advance the fundamental understanding of multipactor physics by developing and carrying out full spectrum, radio frequency (RF) laboratory tests aimed at understanding both single and two-surface multipactor phenomena and at evaluating novel multipactor mitigation approaches for accelerator, space-based RF systems, as well as high power microwave (HPM) applications.

36 MATERIALS SCIENCE↗

High Efficiency 2-Bladed Utility Wind Turbine Enhanced by CoFlow Jet Active Flow Control

The aerodynamic performance and power output of a high efficiency Co-Flow Jet (CFJ) 2-bladed Wind Turbine is studied in this paper. CFJ is a Zero-Net-Mass-Flux (ZNMF) active flow control method that dramatically increases airfoil lift coefficient and suppresses flow separation at a low energy expenditure. The 3D Reynolds Averaged Navier-Stokes (RANS) equations with one-equation Spalart-Allmaras (SA) turbulence model are solved to simulate the 3D flows of the wind turbines. The CFJ-Wind Turbine in this paper is modified from the NREL 3-bladed 3.4 MW reference wind turbine with the same RPM, blade length, distribution of chord, twist, and bending. The CFJ 2-bladed wind turbine utilizes the CFJ-NACA 64 series airfoils at most of the blade span from 31.88\% to the tip. The CFJ injection and suction slots are implemented along the full blade span to enhance the effectiveness and power output. The study shows that the 2-bladed CFJ turbine significantly increases power output compared with the 3-bladed baseline turbine at all wind speeds by 15.8\% at the wind speed of 9.8 m/s and by 25.9\% at 4 m/s respectively. The efficiency enhancement is substantially more at the low wind speed than at high wind speed. This would be very beneficial to increase the annual power output or capacity factor as wind turbines work at the speeds lower than the rated speed for most of the time. The results show that the flow field around the blade surface presents a significant enhanced suction peak near the blade leading edge, which results in a very high tangential force and thus increased wind turbine net power coefficient. Consistent with the previous study for the small NREL Phase VI research wind turbine, this paper demonstrates that CFJ 2-bladed wind turbine is an effective technology to extract more power from the wind at all speeds. This study is just an initial effort to demonstrate the advantage of the CFJ blade with no design optimization. It is believed that there is more potential to further enhance the efficiency improvement.

active flow control↗

Soil and groundwater environmental sensor data, Wax Lake Delta, Louisiana, March 2023 - March 2024

This study evaluates how environmental parameters that integrate biogeochemical processes vary with water table fluctuations in the freshwater Wax Lake Delta (WLD) in Louisiana, U.S.A. This data package contains seven *.csv files and one Excel file that compiles all the data from the individual .csv files. This dataset reports high frequency (15-min) observations of water level, soil redox potential, specific conductance, and pH made for one year along elevation transects located on the older, proximal (OT) and younger, distal (YT) ends of a deltaic island. Water depth relative to the ground surface (cm; HOBO U20L-04; error ± 0.4 cm), water pH and temperature (HOBO MX2501), and specific conductance and temperature (HOBO U24-001) sensors were installed in March 2023. Water depth was corrected for barometric pressure recorded by a separate logger secured to a platform above the highest water level. Soil redox probes (SWAP ORP-40-4-B) were also installed in March 2023. Each probe had four Pt sensors (2 mm width) placed at 10 cm, 20 cm, 30 cm, and 40 cm below the ground surface. Redox data were referenced to an external Ag0/AgCl (3M KCl) reference probe placed in saturated ground and recorded on CR1000X dataloggers (Campbell Scientific) powered by solar panels. A second reference probe was positioned near the primary reference probe for backup and data correction. The tops of the soil redox probes and soil moisture probes were flush with the soil surface so that sensors are reported at their indicated depths below ground surface. Here, we report data collected between 15 March 2023 to 15 March 2024 for all sensors, with some differences due to exact dates of sensor placement or data gaps associated with sensor malfunction. For example, water depth at OT4 was not recorded between March to November 2023. Data flags indicate whether a value is valid (1) or was excluded from data analysis in the associated manuscript (-1).

EARTH SCIENCE > LAND SURFACE > SOILS↗

Ocean Energy Systems Wave Energy Modeling Task 10.4: Numerical Modeling of a Fixed Oscillating Water Column

This paper reports on an ongoing international effort to establish guidelines for numerical modeling of wave energy converters, initiated by the International Energy Agency Technology Collaboration Program for Ocean Energy Systems. Initial results for point absorbers were presented in previous work, and here we present results for a breakwater-mounted Oscillating Water Column (OWC) device. The experimental model is at scale 1:4 relative to a full-scale installation in a water depth of 12.8 m. The power-extracting air turbine is modeled by an orifice plate of 1–2% of the internal chamber surface area. Measurements of chamber surface elevation, air flow through the orifice, and pressure difference across the orifice are compared with numerical calculations using both weakly-nonlinear potential flow theory and computational fluid dynamics. Both compressible- and incompressible-flow models are considered, and the effects of air compressibility are found to have a significant influence on the motion of the internal chamber surface. Recommendations are made for reducing uncertainties in future experimental campaigns, which are critical to enable firm conclusions to be drawn about the relative accuracy of the numerical models. It is well-known that boundary element method solutions of the linear potential flow problem (e.g., WAMIT) are singular at infinite frequency when panels are placed directly on the free surface. This is problematic for time-domain solutions where the value of the added mass matrix at infinite frequency is critical, especially for OWC chambers, which are modeled by zero-mass elements on the free surface. A straightforward rational procedure is described to replace ad-hoc solutions to this problem that have been proposed in the literature.

16 TIDAL AND WAVE POWER↗

Laboratory Experiments Examining the Effect of Thermal and Mechanical Processes on Hydraulic Transmissivity Evolution

Using laboratory slide-hold-slide experiments, at temperatures from 22 to 200 degrees C, to examine effects of fracture reactivation and quasi-static loading on the evolution of fluid transport properties of simulated fractures in Westerly granite. At all temperatures, the in-plane hydraulic transmissivity consistently decays during hold periods resulting in an overall reduction in transmissivity. During the first three to fifteen hours of an experiment, transmissivity decreases rapidly due to the generation of wear products, development of a sliding surface, and compaction of the resulting gouge. Once the sliding surface has developed, the long-term transmissivity decay rate at 22 and 100 degrees C is significantly lower than the transmissivity decay rate during the initial 3-15 hours of the experiment. However, at 200 degrees C, the decay of hydraulic transmissivity remains high throughout the experiment. The long-term decay of hydraulic transmissivity can be fitted with a power law model with more rapid reduction of hydraulic transmissivity at higher temperature. Periods of sliding on the fracture surface result in transient increases in the transmissivity, due to shear dilation, as is expected for Coulomb materials. These transients are superimposed on the long-term decay. When sliding ceases and a new hold period commences, there is a rapid reduction in transmissivity and return to the long-term rate of transmissivity decay. The rate of decay of the transmissivity transients is inversely correlated with temperature, in contrast to the long-term decay and the expected behavior for processes like subcritical crack growth and indentation creep. The higher decay rates that are observed during the initial 3-15 hours of the tests and following sliding, are associated with times that the porosity of the gouge is expected to be high. The difference in decay rates suggests that when the gouge is driven far from equilibrium by active shearing, densification may be dominated by a different mechanism from long-term compaction.

15 GEOTHERMAL ENERGY↗

Chapter 9.12 - Weather, Climatic and Ecological Impacts of Onshore Wind Farms

Wind power is an environmentally sustainable technology that is likely to be part of the solution to the climate change, air pollution, and energy security problems. Despite many positive benefits, the rapid development of wind power has raised concerns about some potential adverse environmental impacts. While converting wind?s kinetic energy into electricity, wind turbines (WTs) modify properties of the atmospheric boundary layer (ABL) including the vertical profiles and surface-atmosphere exchanges of energy, momentum, mass, moisture, and trace gases. Given the current installed capacity and the projected installation worldwide, wind farms (WFs) are likely becoming a major driver of manmade land use change on Earth. Hence, understanding WT-atmosphere-surface interactions and assessing potential environmental impacts of WFs are of significant scientific, societal and economic importance. Here we review our progress in assessing potential impacts of onshore wind power on weather, climate and vegetation activity. A consensus is emerging based on observations and modeling studies that WFs cause a local to regional warming effect, particularly at nighttime, while the impacts on precipitation, wind patterns, crop yields and vegetation activity are uncertain. The warming effect results simply from vertical heat redistribution within the ABL due to turbine-enhanced vertical turbulent mixing in the wakes. At the global scale, with a substantial installation of WFs, mesoscale and climate models predicted large regional changes but small global impacts on temperature, while the impacts on precipitation, clouds, wind patterns and large-scale circulation have large uncertainties and are region specific and scale dependent. Despite increasing number of research efforts, our assessment of potential WF impacts is still very limited. Although the WF impacts are mostly local and limited to the near-surface ABL, this is the layer where we live and plants grow. Hence, more studies are needed to improve our understanding of WT-atmosphere-surface interactions and our capability to model and project the weather, climatic and ecological impacts of large WFs.

atmospheric boundary layer↗

Measurements of multiple heat flux components at the divertor target by using surface eroding thermocouples (invited)

The Surface Eroding Thermocouple (SETC) is a robust diagnostic utilized in DIII-D to provide fast, edge-localized modes (ELMs) resolved heat flux measurements, in particular in geometric regions that are too shadowed for traditional infrared thermography. In order to further investigate the power dissipation in the divertor region, a combination of flush-mounted and recessed SETCs was developed to assess the effect on surface heating from non-charged particles at the divertor target. Utilizing the Divertor Materials Evaluation System sample exposure platform, the first demonstration of the feasibility of using this new method to distinguish between the heat flux from charged particles and that from neutrals and radiative heating was achieved. This paper details the process of using the combination of flush SETCs and recessed SETCs to measure the multiple heat flux components at the divertor target and further discusses how to determine two important ratios, α (ratio of heat flux from charged particles deposit on recessed SETC to that deposit on flush SETC) and β (ratio of heat flux from non-charged particles deposit on recessed SETC to that deposit on flush SETC), in the estimation of the heat flux from non-charged particle sources. Using a time dependent ratio α, it was found that ~50% of the total incident heat flux is attributable to the non-charged particles in the fully detached open divertor in DIII-D. Finally, the new application of similar SETC diagnostics in the Small Angle Slot divertor with a V-like configuration and partial tungsten coated surface (SAS-VW) is also introduced.

47 OTHER INSTRUMENTATION↗

Structure and Dynamics of Aqueous Electrolytes Confined in 2D-TiO 2 /Ti 3 C 2 T 2 MXene Heterostructures

The synthesis of heterostructures of different two-dimensional (2D) materials offers an approach to combine advantages of different materials constituting the heterostructure and ultimately enhance their performance for applications such as electrochemical energy storage, achieving high energy, and high-power densities. Understanding the behavior of ions and solvents in confinement between these dissimilar layers is critical to understand their performance and control. Considering aqueous electrolytes, we explore the heterostructure of 2D lepidocrocite-type TiO 2 (2D-TiO 2 ) and hydroxylated or O-terminated Ti 3 C 2 MXene using ReaxFF molecular dynamics simulations and elastic/quasielastic neutron scattering techniques. Simulating a bilayer water intercalation, we find that the extent of interlayer hydration is impacted most by the surface terminations on the MXene and is marginally affected by 2D-TiO 2 . However, the introduction of 2D-TiO 2 decreases the water self-diffusion due to the notch sites (i.e., surface oxygen ridges) entrapping water molecules. Intercalating alkali cations into the heterostructures, we find that Li + is predominantly adsorbed at the 2D-TiO 2 surface instead of the MXenes with the preferential occupation of the notch sites. In contrast, Na+ forms a planar solvation with water, while K + is adsorbed both at the O-terminated MXene and 2D-TiO 2 . This behavior is altered when OH-terminated MXene is involved—the repulsion from the protons on the MXene surface forces the K + ions to be adsorbed exclusively to 2D-TiO 2 , while Na + retains some of its solvation in the water layer due to its smaller size. In OH-terminated MXenes, we see a consistent transfer of protons from the MXene surface toward 2D-TiO 2 , implying a greater capacity to store protons in the heterostructures. Of the three cations simulated, Na + hinders the proton migration the least and Li + the most because of its position near the 2D-TiO 2 surface. Furthermore, 2D-TiO 2 /MXene heterostructures are likely to exhibit a higher energy density but lower power density, especially with Na + intercalation.

25 ENERGY STORAGE↗

Additive manufacturing of cobalt-based alloy on tool steel by directed energy deposition

Cladding hard-surfacing alloys on tool steel is an effective approach to enhance the surface properties of tool steel. In this study, a Co-based alloy was deposited on tool steel by Directed Energy Deposition (DED) following a three-factor three-level design of experiment matrix with varied laser power, scan speed, and powder flow rate. The microstructure of the deposits was characterized using scanning electron microscopy (SEM). The residual stress on the surface of the samples was measured by the X-ray diffraction (XRD) sin2? technique. The parameters that produced promising deposits were used to fabricate samples for tensile test, four-point bending test, Charpy impact test, and hardness measurement. Our result reveals that the processing parameters have a significant role in the residual stress of the coatings. Residual stress reduces with the increase of laser energy density. Cracks were found at samples with energy density below a threshold. Tensile testing of the coating/substrate combined structure reveals fracture at the coatings with an ultimate tensile strength of 633.9 ± 54.7 MPa. The bi-material interface survived the tensile test, indicating a strong interfacial bond. The four-point bending test of coating/substrate laminates shows an ultimate flexure strength of 860.6 ± 36.9 MPa. Cracks initiated from the coatings ignored the interface and penetrated the substrate, suggesting a solid bi-material bond. Charpy impact test shows the absorbed energy of coating/substrate laminates is more than doubled that of the substrate.

36 MATERIALS SCIENCE↗

Development of an Unmanned Mobile Current Turbine Platform: Preprint

The design and development of a prototype unmanned mobile floating platform, equipped with a custom low-flow marine current turbine for autonomously seeking and harnessing tidal/coastal currents is described. The platform is an unmanned surface vehicle in the form of a catamaran with two electric outboard motors and capabilities for autonomous navigation. An undershot water wheel, aided by a custom flow concentrator, has been selected as the basic design for the marine current turbine, which is mounted on the stern of the unmanned surface vehicle platform. The concept of operation is that the platform would navigate to a designated marine current resource, autonomously anchor at the location, align itself in the current and deploy the current turbine using a custom cable-lift deployment mechanism. As the turbine harnesses the local current, an onboard power-take-off device converts the harnessed mechanical energy to electricity which is stored in onboard batteries. Considerations of deployment in tidal and coastal waters required obtaining the necessary environmental permits for conducting in-water testing; developing required mitigation measures in protecting local wildlife and their habitats; and identifying potential in-water test sites and surveying them for their suitability in terms of the current resource, bottom type, water depth, and local boat traffic. The design and development of the turbine and the results of initial in-water testing are discussed. The potential for scaling up the system for extended capacity is presented.

ENGINEERING,TIDAL AND WAVE POWER↗

Structural breakdown in high power GaN-on-GaN p-n diode devices stressed to failure

The morphology of GaN-on-GaN vertical p-i-n diode devices after reverse-bias electrical stressing to breakdown has been investigated. All failed devices had irreversible structural damage, showing large surface craters that were ∼15–35 μm deep with lengthy surface cracks. Cross-sectional electron micrographs of failed devices showed substantial concentrations of threading dislocations around the cracks and near the crater surfaces. Progressive ion-milling across damaged devices revealed high densities of threading dislocations and the presence of voids beneath the surface cracks; these features were not observed in any unstressed devices. These results should serve as a useful reference for future reliability studies of vertical high-power GaN devices.

Peri, Prudhvi (ORCID:000000022338441X)↗

Optimization of Processing, Microstructure, and Hardness of an Al–Ce–Ni–Mn–Zr Alloy With Laser Additive Manufacturing

Here, this study examines the processing behavior, microstructure, surface roughness, and hardness properties of an aluminum alloy containing 8.2 Ce, 4.5 Ni, 0.5 Mn, and 0.7 Zr (wt%) fabricated using laser powder bed fusion. Sixty samples were produced across a range of laser powers, scan speeds, and hatch spacings to evaluate their effect on porosity, hardness, and microstructural features. Porosity was measured using X-ray computed tomography, while microstructure and surface roughness were characterized by scanning electron (SEM) and laser confocal microscopy. High dense and cracking-free Al–Ni–Ce alloy was successfully manufactured. Porosity showed a U-shaped dependence on energy input, increasing under both insufficient and excessive melting conditions. Hardness increased with cooling rate due to finer cellular structures and solute redistribution. A general statistical model was developed to capture the relationships between processing parameters and material response. Results identify a narrow processing window defined by laser powers between 350 and 370 W, scan speeds from 1400 to 1800 mm/s, and hatch distances between 0.14 and 0.18 mm. Within this window, porosity is minimized (below 0.01%) and hardness is maximized (up to 160 HV), demonstrating that careful control of these parameters enables dense, high strength aluminum components suitable for demanding structural applications.

Aluminum alloys↗

Toward Mass-Production of Transition Metal Dichalcogenide Solar Cells: Scalable Growth of Photovoltaic-Grade Multilayer WSe2 by Tungsten Selenization

Semiconducting transition metal dichalcogenides (TMDs) are promising for high-specific-power photovoltaics due to their desirable band gaps, high absorption coefficients, and ideally dangling-bond-free surfaces. Despite their potential, the majority of TMD solar cells to date are fabricated in a nonscalable fashion, with exfoliated materials, due to the lack of high-quality, large-area, multilayer TMDs. Here, we present the scalable, thickness-tunable synthesis of multilayer WSe2 films by selenizing prepatterned tungsten with either solid-source selenium at 900 degrees C or H2Se precursors at 650 degrees C. Both methods yield photovoltaic-grade, wafer-scale WSe2 films with a layered van der Waals structure and superior characteristics, including charge carrier lifetimes up to 144 ns, over 14x higher than those of any other large-area TMD films previously demonstrated. Simulations show that such carrier lifetimes correspond to ~22% power conversion efficiency and ~64 W g-1 specific power in a packaged solar cell, or ~3 W g-1 in a fully packaged solar module. The results of this study could facilitate the mass production of high-efficiency multilayer WSe2 solar cells at low cost.

carrier lifetime↗

Parameterized anomalous transport model for current-carrying collisionless plasmas in pulsed power inertial confinement fusion

Current delivery in pulsed power inertial confinement fusion is influenced by collisionless current-carrying microturbulent plasmas, which are sourced from electrode surfaces. In this setting, the lower hybrid drift instability—triggered by plasma acceleration—is a leading candidate driver of difficult-to-predict momentum and energy transport. To characterize the nonlinear state of the microturbulent plasma, a parameterized anomalous transport model is developed for the instability, with analytic formulas for anomalous collision frequency, resistivity, and species heating rates. The formulas are expressed in terms of linear-theory variables and four dimensionless parameters that characterize the macroscopic plasma state. The model is built on linear theory analysis, power law analysis, and quasilinear theory analysis, and is validated using a series of nonlinear continuum kinetic Vlasov–Poisson simulations. The theoretical and computational investigation demonstrates that the anomalous collision frequency associated with the instability can be reliably approximated, within about a factor of five or better, by the unscaled linear theory growth rate of the fastest-growing wavenumber mode. This finding enables efficient calculation of anomalous resistivity and species heating rates over a wide range of plasma conditions, resulting in improved predictive capabilities.

Complex functions↗

Reconfigurable Intelligent Surfaces in Action for Nonterrestrial Networks

Next-generation communication technology will be made possible by cooperation between terrestrial networks with nonterrestrial networks (NTNs) composed of high-altitude platform stations (HAPSs) and satellites. Further, as humanity embarks on the long road to establish new habitats on other planets, the cooperation between NTNs and deep-space networks (DSNs) will be necessary. In this regard, we propose the use of reconfigurable intelligent surfaces (RISs) to improve coordination between these networks given that RISs perfectly match the size, weight, and power (SWaP) restrictions of operating in space. Here, a comprehensive framework of RIS-assisted nonterrestrial and interplanetary communications is presented that pinpoints challenges, use cases, and open issues. Furthermore, the performance of RIS-assisted NTNs under environmental effects, such as solar scintillation and satellite drag, is discussed in light of simulation results.

42 ENGINEERING↗