Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Stress test”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Fission gas retention of densely packed uranium carbonitride tristructural-isotropic fuel particles in a 3D printed SiC matrix

The Transformational Challenge Reactor (TCR) fuel form was designed to contain large, densely packed uranium carbonitride (UCN) tristructural-isotropic (TRISO) fuel particles within a 3D printed SiC matrix, increasing the uranium density compared to conventional TRISO fuel forms and offering full geometric freedom for core design. Here, this work summarizes initial low-burnup, high-power irradiation testing of TCR fuel materials, including loose UCN TRISO particles and integral fuel compacts with ~55% TRISO particles by volume, to evaluate fission gas retention. Fission gasses were fully retained in all loose particle tests and in integral compacts irradiated at low (<250 °C) surface temperatures. Initial testing at higher (~700–750 °C) fuel surface temperatures showed fission gas release (FGR) and complete fracture of three compacts, but no FGR was observed in later high temperature tests (~300–750 °C) of both fueled compacts and loose TRISO particles. Calculated thermal stresses in the failed compacts were far less than the measured strength of the SiC matrix and the stresses in some failed compacts were less than those in compacts that did not show FGR. Thermal stress-induced matrix cracks also would not cause complete fracture because the tensile stresses transition to compression in the higher temperature regions. Therefore, fuel failure was likely not caused by thermal stresses and may have been related to leakage currents from the electrical heaters and erratic fuel surface temperatures that were only observed in the test for which failure was observed. In any case, the matrix cracks propagated through the coatings of TRISO particles located in the high-density matrix regions on the peripheries of the compacts, resulting in measurable fission gas release. The discussion focuses on the importance of understanding matrix density distributions and the particle-matrix interface properties to prevent matrix cracks from causing TRISO particle failures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Quantifying the resistance to dislocation glide in single phase FeCrAl alloy

The resistance to dislocation glide associated with slip systems {110}<111> and {112}<111> in single phase FeCrAl alloy is measured via micromechanical testing in a scanning electronic microscopy at room temperature. Two important factors, the shape and orientation of a pillar, are discussed with respect to the glide resistance and stress-strain response. Maximizing Schmid factor of one specific slip system while minimizing others is recommended in order to diminish obvious dislocations-induced hardening during in-situ testing. Apparent Schmid factor analysis is conducted to select grains with preferred orientations. Two types of pillars with conventional cylindrical shape or dog-bone shape are tested under compression to estimate the resistance to dislocation glide and evaluate the effect of pillar shape on the compression stress-strain response. One dog-bone pillar is tested under tension to check the tension-compression isotropy of dislocation slip. We discover that the shape of a pillar to a smaller extent affects the measured resistance but strongly influences the stress strain response. Cylindrical pillars exhibit apparent hardening associated with early yielding due to stress or strain concentration at contact region, while dog-bone pillars show an obvious yielding and continuous shearing without hardening. The resistance is 220 MPa for slip system {110}<111> and 230 MPa for slip system {112}<111>. Finite element analysis is performed to account for the influence of pillar shape and contact condition on mechanical response.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Utah FORGE 2-2446: Closing the Loop Between In-situ Stress Complexity and EGS Fracture Complexity - Workshop Presentation

This is a presentation on the Closing the Loop Between In-situ Stress Complexity and EGS Fracture Complexity project by Lawrence Livermore National Laboratory, presented by Dr. Matteo Cusini. The project's objective was to employ a combination of high-fidelity simulations and true-triaxial block fracturing tests at high temperature to explore the intricate relationship between in-situ stress and hydraulic fracture patterns and better characterize the in-situ stress at Utah FORGE. This presentation was featured in the Utah FORGE R&D Annual Workshop on September 7, 2023. The workshop provided a valuable opportunity to explore the progress made in each of the 17 Research and Development projects funded under Solicitation 2020-1 which aim to enhance our understanding of the crucial factors influencing the development of Enhanced Geothermal Systems (EGS) reservoirs and resources.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

Critical mineral substitutions in IN617: A combined computational and experimental approach to performance evaluation and feasibility

Addressing the escalating demand for critical minerals (CMs) driven by global climate change initiatives, this study explores compositional modifications to Inconel 617 (IN617) by substituting cobalt (Co) with manganese (Mn) across various atomic percentages. Here, we conducted a computational feasibility study employing Molecular Dynamics (MD) simulations to provide strategic guidance for experimental validation. The simulations analyzed tensile strength and corrosion resistance for five modified compositions (M1 to M5) to identify optimal properties. Tensile tests on cubic simulation cells were performed to generate stress-strain curves, revealing the impact of Co replacement with Mn on tensile strength—a metric correlated with hardness. Oxygen penetration simulations were conducted to evaluate corrosion resistance, indicating that reduced oxygen penetration depth corresponds to enhanced resistance. Promising compositions underwent phase diagram calculations for assessing phase stability. The optimal composition (M1), characterized by high tensile strength and minimal oxygen penetration, was chosen for experimental validation using induction melting and friction stir consolidation techniques. The materials were further characterized using SEM-EDS, XRD, and Vickers hardness testing. Our findings suggest that Mn substitution in IN617 can yield mechanical performance at par with high-Co alloys in energy-critical applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Experimental and computational studies of load ratio effect on fatigue crack growth rates in Alloy 709 at elevated temperatures

Abstract Experimental testing and finite element simulations of fatigue crack growth were performed in austenitic 20Cr‐25Ni (Alloy 709) steel at different load ratios and elevated temperatures. The experimental tests were performed using compact tension specimens, and crack growth rates were measured at stress intensity factors ranging between 5 and 35 MPa√m. Fractographic analysis using scanning electron microscopy indicated crack surface roughness and secondary cracking depending on testing temperature and load ratio. Finite element simulations of fatigue crack growth were performed to compute plasticity‐induced crack opening loads and predict crack growth rates. Predictions of fatigue crack growth rates using finite element simulations were performed using the computed crack‐tip opening loads, and they are shown to match well the experimental measurements.

Engineering↗
DOE OSTI2024

Assessment of Training Performance, Degradation and Robustness of Paraffin-Wax Impregnated Nb 3 Sn Demonstrator Under High Magnetic Field

In the context of high-energy physics, the use of Nb 3 Sn superconducting magnets as a cost-effective and reliable technology depends on improvements in the following areas: long development and manufacturing cycles, conductor degradation after thermal cycling, long training, as well as a demonstration in accelerator magnets with a beam aperture of the full potential of modern Nb 3 Sn conductors. In short, performance, robustness, and cost are the three issues to be addressed. The Magnet Development project (MagDev) of the Swiss Accelerator Research and Technology initiative (CHART) at the Paul Scherrer Institute (PSI) aims to contribute to the solutions to each of these issues, re-thinking the manufacturing and design process. Here in our program, every innovation is to be validated by means of a panoply of fast-turnaround tools: from non-powered and powered samples and coils, tested under background field, to low-field subscale magnets and high field short prototypes. This work presents one element in this panoply of R&D vehicles: a stress-managed Nb 3 Sn coil called BigBOX, impregnated with paraffin wax, and tested, through a collaboration with the Magnet Development Program of the United States (US-MDP), in the background field of Brookhaven National Laboratory (BNL)’s common coils dipole DCC17.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Wellbore injectivity response to step-rate CO 2 injection: Coupled thermo-poro-elastic analysis in a vertically heterogeneous formation

Safe and permanent carbon geological storages require an elaborate analysis of geomechanical stability. Subsurface injection of CO 2 changes the local temperature and pore pressure and, further, alters the stress due to thermo-poro-elastic responses. A permanent CO 2 storage testing was conducted in the water leg of Cranfield reservoir in Mississippi, USA, where hosted CO 2 enhanced-oil recovery activities. During CO 2 injection, the injection rate was ramped up twice but the bottom-hole pressure did not increase with the imposed injection rates as expected. This unexpected field observation suggests the possibility of an open-mode fracture development at the injector. However, the injector response and potential fracture development have not been rigorously interpreted with detailed near-wellbore temperature and pore pressure change upon the CO 2 injection. In this study, we performed history matching of CO 2 injection using coupled thermo-poro-elastic reservoir simulation to examine the possibility of fracturing. We built a reservoir model including vertical heterogeneity in both petrophysical and geomechanical properties estimated from well-logging analysis and laboratory experiments. The simulation results show that CO 2 injection changes stresses and support the hypothesis of development of an open-mode fracture at the injector during the Cranfield test. The near-injector region exhibits a large temperature reduction up to 55 °C with ensuing effective horizontal stress reduction up to 9.1 MPa. However, a caprock integrity issue is unlikely because of the horizontal stress contrast within layers and low hydraulic communication with the injection zone. This work indicates that the injectant temperature should be considered in the design of high-rate CO 2 injector.

58 GEOSCIENCES↗
DOE OSTI2023

A new approach to the design of surface subsystems of polymeric insulators for HV and MV apparatus under AC voltage

The design of high voltage and medium voltage AC and DC standoff insulators, and, in general, of insulation systems where surface and interface properties are predominant factors, is based on specifications and standards that rely upon long-term experiences and lab testing. Surface insulating properties depend on electrical and thermal stresses, besides environmental factors, and the inception of extrinsic ageing phenomena, such as partial discharges, can be already a cause of reduced reliability and premature failure (for organic insulating materials). An innovative approach, based on field simulation, discharge modelling, and partial discharge inception measurements is presented by the authors, which can establish a solid basis to optimise insulation design for any type of supply voltage waveform. This method, the three-leg approach, is applied here to a cable system under AC sinusoidal voltage, but it can work for any type of insulation system, such as bushings, switch gears, transformers, rotating machines, and power electronics boards.

42 ENGINEERING↗
DOE OSTI2024

Effects of Temporal Light Modulation on Individuals Sensitive to Pattern Glare

Solid-state lighting systems can vary widely in the degree of temporal light modulation (TLM) of their light output. TLM is known to have visual, cognitive, and behavioral effects but there are few recommendations for limits on the acceptable TLM in everyday lighting systems and there is little information concerning individual differences in sensitivity. This paper is a re-analysis of previously presented data, focusing on two subgroups in a larger sample: those scoring low or high on the Wilkins Pattern Glare Sensitivity (PGS) test, which is a validated test that identifies people at high risk of visual stress. In conclusion, the results show that the PGS groups differed in their sensitivity to TLM conditions, despite short exposures and a restricted field of view.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2025

A Computational Procedure for Assessing I$_{c}(\varepsilon$) in Nb$_{3}$Sn/Bi-2212 Hybrid Magnets

The critical current of superconductors is commonly measured by testing unloaded wires under an external magnetic field. While stressed by intense Lorentz forces, the existing HTS/LTS superconductors are prone to a reduction in critical current before reaching their structural mechanical limit. Here, in this work, the magnetic and mechanical analysis of the FNAL 4-layer Bi-2212/Nb$_{3}$Sn hybrid dipole magnet is reported, aimed at predicting the critical current degradation for both the superconductors during powering at 16T. All the Rutherford cables in the coils of the hybrid magnet were modeled at the strand level in Ansys APDL with the heterogeneous cable model. Utilizing this detailed geometry, it was possible to evaluate the effects of strain on the critical current degradation for both the Nb$_{3}$Sn and Bi-2212 superconductors under the intense Lorentz forces. The analysis presented in this paper integrates strain-dependent critical current laws, with parameters derived from experimental data, to simulate the hybrid magnet's performance for all possible current-powering configurations. The proposed methodology enables a detailed assessment of conductor integrity and I$_{C}(\varepsilon$) reduction in existing hybrid magnet designs, providing a versatile and rigorous framework for optimizing future high-field hybrid magnets.

D'Agliano, A. [Lawrence Berkeley National Laborato↗
DOE OSTI2022

Performance improvements of the windowed multipole formalism using a rational fraction approximation of the Faddeeva function

The windowed multipole (WMP) formalism was introduced as a way to calculate Doppler broadened cross sections on the fly during Monte Carlo simulations. While more arithmetic is needed compared to point-wise cross section look-ups, performance remained competitive from the large memory reductions and sequential data access. The single most expensive function call in a depleted fuel assembly problem using WMP comes from the evaluation of the Faddeeva function, which previously relied on a highly accurate, highly-branching algorithm. This paper explores the use of rational fraction approximations tailored to the domain interest of reactor physics applications and the development of lower accuracy approximations sufficient for our application. The rational approximations were implemented and tested in OpenMC on an infinite medium problem to stress the cross section calculation routine and a PWR assembly problem. In both cases, the rational approximation nearly eliminated the ∼ 20% penalty previously observed when comparing to point-wise libraries. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Progress Report on Model Development for the Transport of Aerosol through Microchannels

This report summarizes the current progress in the development of a phenomenological model of aerosol transport, deposition, and plugging through microchannels. The purpose is to introduce a generic, reliable numerical model for the prediction of aerosol transport, deposition, and plugging in leak paths while accounting for potential plugging formation, to a user community involving researchers, regulators, and industry. In that regard, a Graphical User Interface (GUI) was generated by integrating the individual MATLAB scripts that make up the model and adding additional features to aid the general understanding of the problem to a user. This report focuses on the model development and features included. Further, predictions from the GUI are compared with experimental data for validation. The strength of the GUI is the ability of a user to plug in basic parameters such as the initial pressure conditions and canister model specifications in order to obtain a first principal approximation of vital information such as the blowdown pressure differential, aerosol penetration, and deposition as a function of time. The user can obtain this without the know-how of the underlying MATLAB scripts and thus enables the model to be readily applied by regulators, industry, and shareholders to reduce the uncertainty in the off-site radiological consequences. The report also lists future tasks under this work scope. This includes ongoing efforts to include additional crack geometries (divergent and divergent-convergent slots) to the model; GUI development and improvement based on feedback from users, and integration of aerosol source term data from Sibling Pin tests into the model as we approach realistic canister stress corrosion cracking–induced aerosol release scenarios.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Additive Manufacturing Flaw Assessment Methodology

An evolution fatigue data and flaw tolerance of components produced using the Powder Bed Fusion (PBF) Additive Manufacturing (AM) process is documented in this report. Initial differences in fatigue data for AM components compared to smooth bar fatigue data indicated a need for a more detailed analysis of AM data available in technical literature. The investigation was initiated to support the development of a fatigue analysis methodology for AM components to support the of codification of AM technology for pressure equipment. The project was initiated to collect and analyze stainless steel 304L and 316L AM fatigue test data and corresponding process and quality information to develop S-N and E-N based fatigue data representation. Additional AM fatigue test data including Inconel Ti-6-4 and aluminum alloys were also considered for comparison purposes Metallic AM parts tend to contain various forms of defects distributed throughout the part. If an AM part is subjected to fatigue loading in service, a fatigue analysis needs to be performed during the design process to ensure an acceptable service life for the part. Post-process machining and polishing do not to improve fatigue resistance in any significant degree. The low cycle fatigue regime is of particular interest to this project in support of flaw acceptance criteria currently under development by ASME’s BPTCS/BNCS. Internal defects become exposed as external surface defects during machining for the machining of the AM part to final dimensions. This implies that as long as inherent AM defects are within a controlled limit in terms of both size and distribution characteristics, the corresponding fatigue test data in terms of either S-N (stress life) or E-N (strain life) can be investigated and characterized to establish fatigue properties of AM parts for design and fatigue evaluation purposes. The resulting S-N or E-N curves and their scatter bands can be used to derive fatigue design allowable stress values by capturing the effects of distributed discontinuities within an acceptable limit.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Recent Developments at the Raft River Geothermal Field

The Raft River geothermal field, located in Cassia County in southwestern Idaho, is the site of a Department of Energy Enhanced Geothermal System project. U.S. Geothermal, Inc. currently produces about 11 MWe from Precambrian metamorphic rocks. These lie beneath ~5,000 ft of Quaternary and Tertiary volcaniclastic and volcanic deposits. Maximum temperatures range from 271°F to 300°F. Well RRG-9 ST1, the well targeted for stimulation is located approximately 1 mile south of the main bore field. The open hole section of the well, from 5,551 to 5,900 ft MD, consists of Precambrian Elba Quartzite, the stimulation target, granite and minor diabase. Prior to setting the casing acoustic, gamma ray, and density logs were run. After completing the well, a step rate/step down test was conducted. The maximum injection rate achieved was 18 bpm at a wellhead pressure of 1,150 psig. A borehole televiewer run in the open hole section showed evidence of more than eighty fractures. The majority of these fractures trend from N20⁰W to N20°E and dip from 40° to 60°W. Permeable fractures were encountered in the Elba Quartzite at 5,640-5,660 ft MD. Analysis of the injection test indicates that the minimum in-situ principal stress in this zone is 3,050-3,200 psi, corresponding to a fracture gradient of 0.59-0.62 psi/ft. A discrete fracture network model was developed using measured and inferred fracture orientations, distributions and dimensions. A three-phase stimulation program is proposed for RRG-9 ST-1. During the first two stages, water at 140°F, and later 40°F, will be injected to pre-condition and thermally fracture the reservoir. Here, the third stage will consist of a high rate, large volume conventional hydraulic stimulation.

Bradford, Jacob↗
DOE OSTI2022

Mechanical Characterization of Loblolly Pine

Biorefineries are faced with various material flow challenges during feeding and handling, due to inherent variability and inhomogeneity of biomass feedstocks. This impacts the efficiency of refinery processes and unit operations. Proper characterization of bulk properties allows for optimal process design and reduction of overall costs. This work is aimed at evaluating the physical and mechanical properties that impact bulk flow of loblolly pine. Cyclic axial compression tests are performed to elucidate consolidation behavior under different stress conditions. The results are then used to develop correlations between material parameters (particle size, tissue type, moisture content) and Elastic Modulus of bulk samples.

09 BIOMASS FUELS↗
DOE OSTI2020

Damp Heat Induced Degradation of Silicon Heterojunction Solar Cells With Cu-Plated Contacts

Damp heat exposure is one of the most stringent environments for testing the durability of solar cells in packaged modules. Damp heat stresses and induces a variety of degradation modes in solar cells and modules: for example, moisture-induced corrosion of electrodes and interconnections, deterioration of polymeric materials, and/or thermally activated diffusion processes. To screen for these and other potential degradation modes, we subject one-cell modules containing silicon heterojunction (SHJ) solar cells with Cu-plated contacts to extended damp heat tests at 85 °C/85% relative humidity. SHJ cells were laminated with two common encapsulants: ethylene vinyl acetate (EVA) and polyolefin elastomer (POE), and two constructions: glass-backsheet and glass-glass. We observe degradation in all components of solar cell maximum power (PMP): current, voltage, and fill factor, and find evidence of increased carrier recombination and nonideal diode behavior with increasing stress. For glass-backsheet constructions, EVA samples generally degrade more than POE by a factor of approximately 1.5x PMP, and the different encapsulants produce different degradation patterns. Similar trends are observed in glass-glass modules, but to a lesser degree. In a different experiment, we observe a decrease in effective minority carrier lifetime of nonmetallized SHJ precursors measured after damp heat. This implies that some degradation unrelated to the contacts is to be expected and confirms the observation of increasing recombination.

14 SOLAR ENERGY↗
DOE OSTI2024

Multiobjective Constrained Symbolic Regression for Predictive Modeling of Material Creep Behavior

When creep testing is repeated on samples of the same alloy under the same parametric conditions (i.e., stress and temperature), the resulting strain/time curves can vary from each other considerably as shown in Figure 1 [1]. The time required to creep test a material to rupture can extend to the order of years. Because of this, a numerical model that can quickly analyze the incomplete results of an ongoing experiment to predict 1) the incomplete portion of the strain/time curve leading up to the rupture point and 2) the rupture point itself would be of great utility to the materials community. Such a model has the potential to save 1) the time required to finish running the experiment to rupture 2) the associated monetary cost of finishing said experiment. Furthermore, it would be advantageous if the predictive model could give a parametric function modeling strain/time curves for material scientists to investigate the impact of the temperature and stress parameters on the resulting creep behavior. This work introduces a piecewise symbolic regression algorithm to predict the remainder of the strain/time curve. Preliminary results show good model performance.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Predictive machine learning approaches for the microstructural behavior of multiphase zirconium alloys

Abstract Zirconium alloys are widely used in harsh environments characterized by high temperatures, corrosivity, and radiation exposure. These alloys, which have a hexagonal closed packed (h.c.p.) structure thermo-mechanically degrade, when exposed to severe operating environments due to hydride formation. These hydrides have a different crystalline structure, than the matrix, which results in a multiphase alloy. To accurately model these materials at the relevant physical scale, it is necessary to fully characterize them based on a microstructural fingerprint, which is defined here as a combination of features that include hydride geometry, parent and hydride texture and crystalline structure of these multiphase alloys. Hence, this investigation will develop a reduced order modeling approach, where this microstructural fingerprint is used to predict critical fracture stress levels that are physically consistent with microstructural deformation and fracture modes. Machine Learning (ML) methodologies based on Gaussian Process Regression, random forests, and multilayer perceptrons (MLP) were used to predict material fracture critical stress states. MLPs, or neural networks, had the highest accuracy on held-out test sets across three predetermined strain levels of interest. Hydride orientation, grain orientation or texture, and hydride volume fraction had the greatest effect on critical fracture stress levels and had partial dependencies that were highly significant, and in comparison hydride length and hydride spacing have less effects on fracture stresses. Furthermore, these models were also used accurately predicted material response to nominal applied strains as a function of the microstructural fingerprint.

36 MATERIALS SCIENCE↗