Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Stress Modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Experimental and analytical evaluation of the effects of simulated engine inlets on the blade vibratory stresses of the SR-3 model prop-fan

A cooperative wind tunnel test program, referred to as GUN-3, had been conducted previously to assess the effect of inlet configuration and location on the inlet face pressure recovery and inlet drag in the presence of a high-speed advanced turboprop. These tests were conducted with the inlets located just downstream of the SR-3 model Prop-Fan, a moderately swept, eight-bladed 62.2 cm (24.5 inch) diameter advanced, high-speed turboprop model fabricated from titanium. During these tests, two blades of the SR-3 model Prop-Fan were strain gaged to measure the vibratory blade stresses occurring during the inlet aerodynamic test program. The purpose of the effort reported herein was to reduce and analyze the test results related to the vibratory strain gage measurements obtained. Three inlet configurations had been tested. These were: (1) single scoop, (2) twin scoop, and (3) annular. Each of the three inlets was tested at a position just behind the rotor. The single scoop inlet was also tested at a position further aft. Tests were also done without an inlet. These results emphasize the importance of avoiding critical speeds in the continuous operating range.

Bansal, Prem N.↗
NASA NTRS1990

An assessment and application of turbulence models for hypersonic flows

The current approach to the Accurate Computation of Complex high-speed flows is to solve the Reynolds averaged Navier-Stokes equations using finite difference methods. An integral part of this approach consists of development and applications of mathematical turbulence models which are necessary in predicting the aerothermodynamic loads on the vehicle and the performance of the propulsion plant. Computations of several high speed turbulent flows using various turbulence models are described and the models are evaluated by comparing computations with the results of experimental measurements. The cases investigated include flows over insulated and cooled flat plates with Mach numbers ranging from 2 to 8 and wall temperature ratios ranging from 0.2 to 1.0. The turbulence models investigated include zero-equation, two-equation, and Reynolds-stress transport models.

Coakley, T. J.↗
NASA NTRS1993

Lifetime Reliability Evaluation of Structural Ceramic Parts with the CARES/LIFE Computer Program

The computer program CARES/LIFE calculates the time-dependent reliability of monolithic ceramic components subjected to thermomechanical and/or proof test loading. This program is an extension of the CARES (Ceramics Analysis and Reliability Evaluation of Structures) computer program. CARES/LIFE accounts for the phenomenon of subcritical crack growth (SCG) by utilizing the power law, Paris law, or Walker equation. The two-parameter Weibull cumulative distribution function is used to characterize the variation in component strength. The effects of multiaxial stresses are modeled using either the principle of independent action (PIA), Weibull's normal stress averaging method (NSA), or Batdorf's theory. Inert strength and fatigue parameters are estimated from rupture strength data of naturally flawed specimens loaded in static, dynamic, or cyclic fatigue. Two example problems demonstrating cyclic fatigue parameter estimation and component reliability analysis with proof testing are included.

Nemeth, Noel N.↗
NASA NTRS1993

Time-dependent reliability analysis of ceramic engine components

The computer program CARES/LIFE calculates the time-dependent reliability of monolithic ceramic components subjected to thermomechanical and/or proof test loading. This program is an extension of the CARES (Ceramics Analysis and Reliability Evaluation of Structures) computer program. CARES/LIFE accounts for the phenomenon of subcritical crack growth (SCG) by utilizing either the power or Paris law relations. The two-parameter Weibull cumulative distribution function is used to characterize the variation in component strength. The effects of multiaxial stresses are modeled using either the principle of independent action (PIA), the Weibull normal stress averaging method (NSA), or the Batdorf theory. Inert strength and fatigue parameters are estimated from rupture strength data of naturally flawed specimens loaded in static, dynamic, or cyclic fatigue. Two example problems demonstrating proof testing and fatigue parameter estimation are given.

Nemeth, Noel N.↗
NASA NTRS1994

Durability evaluation of ceramic components using CARES/LIFE

The computer program CARES/LIFE calculates the time-dependent reliability of monolithic ceramic components subjected to thermomechanical and/or proof test loading. This program is an extension of the CARES (Ceramics Analysis and Reliability Evaluation of Structures) computer program. CARES/LIFE accounts for the phenomenon of subcritical crack growth (SCG) by utilizing the power law, Paris law, or Walker equation. The two-parameter Weibull cumulative distribution function is used to characterize the variation in component strength. The effects of multiaxial stresses are modeled using either the principle of independent action (PIA), the Weibull normal stress averaging method (NSA), or the Batdorf theory. Inert strength and fatigue parameters are estimated from rupture strength data of naturally flawed specimens loaded in static, dynamic, or cyclic fatigue. Application of this design methodology is demonstrated using experimental data from alumina bar and disk flexure specimens which exhibit SCG when exposed to water.

Nemeth, Noel N.↗
NASA NTRS2001

Two-Equation Turbulence Models for Prediction of Heat Transfer on a Transonic Turbine Blade

Two versions of the two-equation k-omega model and a shear stress transport (SST) model are used in a three-dimensional, multi-block, Navier-Stokes code to compare the detailed heat transfer measurements on a transonic turbine blade. It is found that the SST model resolves the passage vortex better on the suction side of the blade, thus yielding a better comparison with the experimental data than either of the k-w models. However, the comparison is still deficient on the suction side of the blade. Use of the SST model does require the computation of distance from a wall, which for a multiblock grid, such as in the present case, can be complicated. However, a relatively easy fix for this problem was devised. Also addressed are issues such as (1) computation of the production term in the turbulence equations for aerodynamic applications, and (2) the relation between the computational and experimental values for the turbulence length scale, and its influence on the passage vortex on the suction side of the turbine blade.

Garg, Vijay K.↗
NASA NTRS2003

Multiaxial Temperature- and Time-Dependent Failure Model

A temperature- and time-dependent mathematical model predicts the conditions for failure of a material subjected to multiaxial stress. The model was initially applied to a filled epoxy below its glass-transition temperature, and is expected to be applicable to other materials, at least below their glass-transition temperatures. The model is justified simply by the fact that it closely approximates the experimentally observed failure behavior of this material: The multiaxiality of the model has been confirmed (see figure) and the model has been shown to be applicable at temperatures from -20 to 115 F (-29 to 46 C) and to predict tensile failures of constant-load and constant-load-rate specimens with failure times ranging from minutes to months..

Richardson, David↗
NASA NTRS2016

Numerical Simulation of a Complete Low-Speed Wind Tunnel Circuit

A numerical simulation of the complete circuit of the NASA Langley 14 x 22-ft low-speed wind tunnel is described. Inside the circuit, all turning vanes are modeled as well as the five flow control vanes downstream of the 1st corner. The fan drive system is modeled using an actuator disk for the fan blades coupled with the fan nacelle. All the surfaces are modeled as viscous walls except the turning vanes, which were modeled as inviscid surfaces. NASA Langley's TetrUSS unstructured grid software was used for grid generation and flow simulation. Two turbulence models were employed in the present study, namely, the one-equation Spalart-Allmaras model and the shear stress transport (SST) model of Menter. The paper shows the flow characteristics in the circuit and compares the results with experimental data where available.

Nayani, Sudheer N.↗
NASA NTRS2020

Progressive Failure Analysis Correlation with Notched Composite Laminate Test Data

Testing of small and intermediate laminate panels with notches was performed and Progressive Failure Analyses (PFA) models were developed for aid in test planning and for correlation with the test data. Two progressive damage failure models were included in the study: the commercially available Abaqus built-in damage model and COmplete STress Reduction (COSTR) damage model developed at NASA Langley Research Center (LaRC). The finite elements models used for the analysis were developed using shell elements. The pre-test PFA results obtained from the two damage models were compared to test data. Then a post-test PFA with updated material properties based on additional available material property data was executed with the COSTR damage model and compared to the test data. The panels tested in compression all exhibited less scatter in the failure load with self-similar failure behavior. The panels tested in tension exhibited more scatter in the failure load with a failure mode that included delamination of plies. However, a self-similar crack path was also observed as the overall failure mode for all panels tested. When comparing test data to the pre-test analysis results, both damage models with shell element models were considered adequate for predicting the behavior and failure load of both the small and intermediate panels when tested in compression. However, for the tension load cases, larger differences were observed between the test and analysis results. When comparing test data to the post-test analysis performed using the COSTR damage model, better correlation was observed. However, large discrepancies were still observed for the tension load cases. Consequently, a higher fidelity finite element model including solid elements for sub-laminates and the modeling of cohesive layers between sub-laminate layers is recommended for tension loading of notched composite laminates.

Damage Model,Progressive Failure Analysis,Open Hol↗
DOE OSTI2023

MODFLOW6 models used to evaluate potential stresses and hydrologic conditions driving water-level fluctuations in well ER-5-3-2, Frenchman Flat, Southern Nevada

The hydrograph for well ER-5-3-2 in Frenchman Flat, southern Nevada, has previously unexplained water-level fluctuations. Four, three-dimensional, groundwater models (MODFLOW 6) were developed to evaluate potential stresses and hydrologic conditions affecting the well ER-5-3-2 hydrograph. Four model scenarios were developed that simulated: (1) wellbore leakage without recharge, (2) wellbore leakage with recharge, (3) shallow (low transmissivity) and deep (high transmissivity) carbonate rocks, and (4) lateral heterogeneity of carbonate rocks. Input and output files for the four model scenarios are in the model and output directories, respectively. Hydraulic conductivity, specific storage, and wellbore-leakage rates (when simulated) were estimated with parameter estimation (PEST) by minimizing a weighted composite, sum-of-squares objective function. The objective function was informed by measurement and Tikhonov regularization observations. Measurement observations included drawdowns from the constant-rate aquifer test and water-level altitudes measured in well ER-5-3-2 from 2001-2021. Tikhonov regularization informed hydraulic conductivity and specific storage parameters that were insensitive to measurement observations, where homogeneity was the preferred relation. Batch files, executables, and MODFLOW 6, PEST, and post-processing utilities are in the ancillary directory. Supplementary data also are included in the ancillary directory, including site information, high-frequency water-level and aquifer-test data, transmissivity estimates, water-chemistry data, and water-temperature analyses. This USGS data release contains data, analyses, and model files for the simulations and analysis results described in U.S. Geological Survey Scientific Investigations Report (https://doi.org/10.3133/sir20225132).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Data-Efficient Dimensionality Reduction and Surrogate Modeling of High-Dimensional Stress Fields

Tensor datatypes representing field variables like stress, displacement, velocity, etc., have increasingly become a common occurrence in data-driven modeling and analysis of simulations. Numerous methods [such as convolutional neural networks (CNNs)] exist to address the meta-modeling of field data from simulations. As the complexity of the simulation increases, so does the cost of acquisition, leading to limited data scenarios. Modeling of tensor datatypes under limited data scenarios remains a hindrance for engineering applications. Here, in this article, we introduce a direct image-to-image modeling framework of convolutional autoencoders enhanced by information bottleneck loss function to tackle the tensor data types with limited data. The information bottleneck method penalizes the nuisance information in the latent space while maximizing relevant information making it robust for limited data scenarios. The entire neural network framework is further combined with robust hyperparameter optimization. We perform numerical studies to compare the predictive performance of the proposed method with a dimensionality reduction-based surrogate modeling framework on a representative linear elastic ellipsoidal void problem with uniaxial loading. The data structure focuses on the low-data regime (fewer than 100 data points) and includes the parameterized geometry of the ellipsoidal void as the input and the predicted stress field as the output. The results of the numerical studies show that the information bottleneck approach yields improved overall accuracy and more precise prediction of the extremes of the stress field. Additionally, an in-depth analysis is carried out to elucidate the information compression behavior of the proposed framework.

artificial intelligence↗
NASA NTRS1990

July 16, 1987 revisited: Lessons for modelers

A cross pattern was flown by the NCAR Electra in the restricted air space around San Nicolas Island (SNI). There was available a LANDSAT image coincident with the mission. The variability of cloud thickness along the flight track is discussed. The evidence points to variability in the water vapor content above the inversion as the controlling factor. This compounds the difficulty of parameterizing these clouds in General Circulation Models (GCMs). The importance of specifying correctly the upper boundary condition in cloud models is stressed. Particularly, in GCMs, calculating the humidity in the lower layers of the model is crucial for successful parameterization of marine stratocumulus clouds.

Hanson, Howard P.↗
NASA NTRS2001

A Three-Dimensional CFD Investigation of Secondary Flow in an Accelerating, 90 deg Elbow

NASA Glenn Research Center has recently applied the WIND National Code flow solver to an accelerating elbow with a 90 deg. bend to reveal aspects of secondary flow. This elbow was designed by NACA in the early 1950's such that flow separation would be avoided. Experimental testing was also done at that time. The current three dimensional CFD investigation shows that separation has indeed been avoided. Using its three-dimensional capability, this investigation provides various viewpoints in several planes that display the inception, development, and final location of a passage vortex. Its shape first becomes discernible as a vortex near the exit of the bend. This rendition of the exit passage vortex compares well with that found in the experiments. The viewpoints show that the passage vortex settles on the suction surface at the exit about one-third of the distance between the plane wall and midspan. Furthermore, it projects into the mainstream to about one-third of the channel width. Of several turbulence models used in this investigation, the Spalart Alimaras, Baldwin Lomax, and SST (Shear Stress Transport) models were by far the most successful in matching the experiments.

Cavicchi, Richard H.↗
NASA NTRS2003

CARES/LIFE Ceramics Analysis and Reliability Evaluation of Structures Life Prediction Program

This manual describes the Ceramics Analysis and Reliability Evaluation of Structures Life Prediction (CARES/LIFE) computer program. The program calculates the time-dependent reliability of monolithic ceramic components subjected to thermomechanical and/or proof test loading. CARES/LIFE is an extension of the CARES (Ceramic Analysis and Reliability Evaluation of Structures) computer program. The program uses results from MSC/NASTRAN, ABAQUS, and ANSYS finite element analysis programs to evaluate component reliability due to inherent surface and/or volume type flaws. CARES/LIFE accounts for the phenomenon of subcritical crack growth (SCG) by utilizing the power law, Paris law, or Walker law. The two-parameter Weibull cumulative distribution function is used to characterize the variation in component strength. The effects of multiaxial stresses are modeled by using either the principle of independent action (PIA), the Weibull normal stress averaging method (NSA), or the Batdorf theory. Inert strength and fatigue parameters are estimated from rupture strength data of naturally flawed specimens loaded in static, dynamic, or cyclic fatigue. The probabilistic time-dependent theories used in CARES/LIFE, along with the input and output for CARES/LIFE, are described. Example problems to demonstrate various features of the program are also included.

Nemeth, Noel N.↗
NASA NTRS1972

Coronary flow and left ventricular function during environmental stress.

A canine model was used to study the effects of different environmental stresses on the heart and coronary circulation. The heart was surgically instrumented to measure coronary blood flow, left ventricular pressure, and other cardiovascular variables. Coronary flow was recorded by telemetry. Physiologic data were processed and analyzed by analog and digital computers. By these methods the physiologic response to altitude hypoxia, carbon monoxide, hypercapnia, acceleration, exercise, and the interaction of altitude hypoxia and carbon monoxide were described. The effects of some of these stresses on the heart and coronary circulation are discussed.

Erickson, H. H.↗
DOE OSTI2021

Large-Scale Welding Process Simulation by GPU Parallelized Computing

The computational design of industrially relevant welded structures is extremely time consuming due to coupled physics and high nonlinearity. Previously, most welding distortion and residual stress simulations have been limited to small coupons and reduced order (from three-dimensional [3D] to two-dimensional [2D]), or inherent strain approximations were used for large structures. In this current study, an explicit finite element code based on a graphics processing unit was utilized to perform 3D transient thermomechanical simulation of structural components during welding. Laser brazing of aluminum alloy panels as representative of automotive manufacturing scenarios was simulated to predict out-of-plane distortion under different clamping conditions. The predicted deformation pattern and magnitude were validated by laser scanning data of physical assemblies. In addition, the code was used to investigate residual stresses developed during multipass arc welding of a nuclear industry pressurizer surge nozzle and subsequent welding repair where a 3D simulation was necessary. Taking the experimental data as reference, the 3D model predicted better residual stress distribution than a typical 2D asymmetrical model. Stress evolution in welding repair was also presented and discussed in this study. Furthermore, the efficient numerical model made it feasible to use integrated computational welding engineering to simulate welding processes for large-scale structures.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1991

Computation of turbulent high speed mixing layers using a two-equation turbulence model

A two-equation turbulence model was extended to be applicable for compressible flows. A compressibility correction based on modelling the dilational terms in the Reynolds stress equations were included in the model. The model is used in conjunction with the SPARK code for the computation of high speed mixing layers. The observed trend of decreasing growth rate with increasing convective Mach number in compressible mixing layers is well predicted by the model. The predictions agree well with the experimental data and the results from a compressible Reynolds stress model. The present model appears to be well suited for the study of compressible free shear flows. Preliminary results obtained for the reacting mixing layers are included.

Narayan, J. R.↗
NASA NTRS1996

Verification of Orthogrid Finite Element Modeling Techniques

The stress analysis of orthogrid structures, specifically with I-beam sections, is regularly performed using finite elements. Various modeling techniques are often used to simplify the modeling process but still adequately capture the actual hardware behavior. The accuracy of such 'Oshort cutso' is sometimes in question. This report compares three modeling techniques to actual test results from a loaded orthogrid panel. The finite element models include a beam, shell, and mixed beam and shell element model. Results show that the shell element model performs the best, but that the simpler beam and beam and shell element models provide reasonable to conservative results for a stress analysis. When deflection and stiffness is critical, it is important to capture the effect of the orthogrid nodes in the model.

Steeve, B. E.↗