Prediction of the stability derivatives of large flexible prop/rotors by a simplified analysis
Blade flexibility effects on static stability derivatives of prop/rotors in propeller flight mode
Magee, J. P.↗
SEARCH · Engineering Papers
Results for “Static analysis”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Development of a preliminary high-angle-of-attack nose-down pitch control requirement for high-performance aircraft
The requirements for high-angle-of-attack nose-down pitch control for advanced high-performance aircraft are discussed. Background information on fundamental factors that influence and, to a large extent, determine the high angle-of-attack nose-down control requirement is briefly reviewed. Guidelines currently proposed by other sources which attempt to define these requirements are discussed. A requirement based on NASA analysis of the characteristics of existing relaxed static stability (RSS) aircraft is presented. This analysis could provide the basis for a preliminary design guide.
Nguyen, Luat T.↗
The analysis of non-linear dynamic behavior (including snap-through) of postbuckled plates by simple analytical solution
Static postbuckling and nonlinear dynamic analysis of plates are usually accomplished by multimode analyses, although the methods are complicated and do not give straightforward understanding of the nonlinear behavior. Assuming single-mode transverse displacement, a simple formula is derived for the transverse load displacement relationship of a plate under in-plane compression. The formula is used to derive a simple analytical expression for the static postbuckling displacement and nonlinear dynamic responses of postbuckled plates under sinusoidal or random excitation. Regions with softening and hardening spring behavior are identified. Also, the highly nonlinear motion of snap-through and its effects on the overall dynamic response can be easily interpreted using the single-mode formula. Theoretical results are compared with experimental results obtained using a buckled aluminum panel, using discrete frequency and broadband point excitation. Some important effects of the snap-through motion on the dynamic response of the postbuckled plates are found.
Ng, C. F.↗
Empirical prediction of saline water atomization pressure loss and spray phase change using local flow pressure analysis
A pressure analysis technique was developed to obtain spray spatial evaporation profile in a thermal desalination process. The technique can replace temperature-based evaporation measurement methods that are challenged by liquid-phase interference. It also provides an alternative to optical methods with high cost and complexity. Fundamental analysis was developed to determine local humidity ratios from changes in local static and dynamic pressures. The analysis was applied to data obtained from an external mixing air-assist atomizer. An empirical model was developed for the pressure loss in atomization process and was used in the analysis of humidity ratio. The results were used to develop empirical correlations for local humidity ratio in spray mediums using inlet conditions. Utilizing inlet conditions to predict evaporation profiles is an important contribution as it eliminates the need to take local spray measurements. Obtaining local data is often difficult and expensive; Our method and correlation circumvent the need for that. Finally, the correlations presented in this paper apply to saline water sprays with total dissolved salt of 0-10 wt%. The salinity-specific correlations are accurate to within ±10% of experimental data. The individual models were aggregated into a unified correlation for salinities within 0-10 wt%. The unified correlation is accurate to within ±18% of experimental data.
42 ENGINEERING↗
Crack-Free Joining of High-Strength AA7055 Sheets by Friction Based Self-Piercing Riveting with the Aid of Numerical Design
Unique friction-based self-piercing riveting (F-SPR) was employed to join high-strength, low-ductility aluminum alloy 7055 for lightweight vehicle applications. This study aimed to maximize the joint strength of the AA7055 F-SPR joint while avoiding cracking issues due to low ductility at room temperature. A fully coupled Eulerian–Lagrangian (CEL) model was employed to predict the process temperature during F-SPR, and the temperature field was then mapped onto a 2D axisymmetric equivalent model for accelerated numerical analysis. The geometry, dimensions, and material strength of the rivet, as well as the depth of the die cavity and plunging depth, were investigated to enhance joint formation. Also, a static finite-element analysis model was developed to predict and analyze the stress distribution in the rivet under different mechanical testing loading conditions. Overall, the numerical model showed good agreement with the experiment results, such as joint formation and mechanical joint strength. With the aid of virtual fabrication through numerical modeling, the joint design iterations and process development time of F-SPR were greatly reduced regarding the goal of lightweight, high-strength aluminum joining.
36 MATERIALS SCIENCE↗
Fatigue tests on big structure assemblies of concorde aircraft
Fatigue tests on structural assemblies of the Concorde supersonic transport aircraft are reported. Two main sections of the aircraft were subjected to pressure, mechanical load, and thermal static tests. The types of fatigue tests conducted and the results obtained are discussed. It was concluded that on a supersonic aircraft whose structural weight is a significant part of the weight analysis, many fatigue and static strength development tests should be made and fatigue and thermal tests of the structures are absolutely necessary.
Nguyen, V. P.↗
Streamlined Loads Analysis of Floating Wind Turbines With Fiber Rope Mooring Lines
This paper presents an approach for more accurate yet relatively streamlined accounting for the nonlinear characteristics of synthetic fiber rope mooring lines for floating wind turbines. First, we select a minimal set of parameters that can efficiently approximate a mooring line material's quasi-static and dynamic stiffness characteristics. We also develop a set of baseline coefficients for different rope materials based on published product information and research papers. We then expand a quasi-static mooring model to include dynamic mooring line stiffness terms in a way that allows the nonlinear stiffness behavior of fiber ropes to be considered even in quasi-static analyses. For dynamic analysis, we have updated the model MoorDyn, coupled with OpenFAST, to work with the new dynamic mooring line stiffness terms. This includes the implementation of a new viscoelastic approach that allows the tension-strain relation of each mooring line segment to vary between two stiffness values, depending on the strain rate. After presenting the formulation of the approaches for modeling synthetic ropes, they are demonstrated on a floating wind turbine mooring system with taut polyester rope mooring lines. The results are compared with those of other approaches of similar fidelity, including the static-dynamic method and separate simulations with static and dynamic stiffness values. Comparing the results shows the ability of the new method to match the results of the previous methods in a more streamlined manner.
elasticity↗
Streamlined Loads Analysis of Floating Wind Turbines With Fiber Rope Mooring Lines: Preprint
This paper presents an approach for more accurate yet relatively streamlined accounting for the nonlinear characteristics of synthetic fiber rope mooring lines for floating wind turbines. First, we select a minimal set of parameters that can efficiently approximate a mooring line material's quasi-static and dynamic stiffness characteristics. We also develop a set of baseline coefficients for different rope materials based on published product information and research papers. We then expand a quasi-static mooring model to include dynamic mooring line stiffness terms in a way that allows the nonlinear stiffness behavior of fiber ropes to be considered even in quasi-static analyses. For dynamic analysis, we have updated the model MoorDyn, coupled with OpenFAST, to work with the new dynamic mooring line stiffness terms. This includes the implementation of a new viscoelastic approach that allows the tension-strain relation of each mooring line segment to vary between two stiffness values depending on the strain rate. After presenting the formulation of the approaches for modeling synthetic ropes, they are demonstrated on a floating wind turbine mooring system with taut polyester rope mooring lines. The results are compared with those of other approaches of similar fidelity including the static-dynamic method and separate simulations with static and dynamic stiffness values. Comparing the results shows the ability of the new method to match the results of the previous methods in a more streamlined manner.
elasticity↗
Asymptotic theory of statics and dynamics of elastic circular cylindrical shells and analysis of the accuracy of the different variants of the Kirchhoff-Love theory
Asymptotic formulas for elastic cylindrical shells and analysis of Kirchhoff-Love theory
ELASTIC SHELL↗
Numerical analysis of stiffened shells of revolution. Volume 2: Users' manual for STAR-02S - shell theory automated for rotational structures - 2 (statics), digital computer program
A procedure for the structural analysis of stiffened shells of revolution is presented. A digital computer program based on the Love-Reissner first order shell theory was developed. The computer program can analyze orthotropic thin shells of revolution, subjected to unsymmetric distributed loading or concentrated line loads, as well as thermal strains. The geometrical shapes of the shells which may be analyzed are described. The shell wall cross section can be a sheet, sandwich, or reinforced sheet or sandwich. General stiffness input options are also available.
Svalbonas, V.↗
Design Optimization of Stiffened Panels with Postbuckling Constraints
The funding provided by the grant is used to complete the final stages of the development of a geometrically nonlinear analysis and design capability for the static response of compressively loaded prismatic plate structures. The analysis is based on the nonlinear finite strip method and is applicable for structures, such as stiffened panels or box columns, that can be modeled as assemblages of finite length plate strips. In an effort to reduce the computational cost of the nonlinear finite strip method, thus making it suitable for use in the design optimization environment, reduced basis techniques as described in various references by Noor are used in conjunction with the finite strip method. In addition, an efficient scheme for tracing the nonlinear equilibrium paths through highly nonlinear response curves was implemented. The new scheme, which is referred to as the normal flow algorithm, is based on homotopy methods, and is capable of negotiating highly nonlinear limit point instabilities with a reduced computational cost compared to the popular Ricks/Wempner and Chrisfield algorithms.
Guerdal, Zafer↗
Aerodynamics for the Mars Phoenix Entry Capsule
Pre-flight aerodynamics data for the Mars Phoenix entry capsule are presented. The aerodynamic coefficients were generated as a function of total angle-of-attack and either Knudsen number, velocity, or Mach number, depending on the flight regime. The database was constructed using continuum flowfield computations and data from the Mars Exploration Rover and Viking programs. Hypersonic and supersonic static coefficients were derived from Navier-Stokes solutions on a pre-flight design trajectory. High-altitude data (free-molecular and transitional regimes) and dynamic pitch damping characteristics were taken from Mars Exploration Rover analysis and testing. Transonic static coefficients from Viking wind tunnel tests were used for capsule aerodynamics under the parachute. Static instabilities were predicted at two points along the reference trajectory and were verified by reconstructed flight data. During the hypersonic instability, the capsule was predicted to trim at angles as high as 2.5 deg with an on-axis center-of-gravity. Trim angles were predicted for off-nominal pitching moment (4.2 deg peak) and a 5 mm off-axis center-ofgravity (4.8 deg peak). Finally, hypersonic static coefficient sensitivities to atmospheric density were predicted to be within uncertainty bounds.
Edquist, Karl T.↗
Assessment of current state of the art in modeling techniques and analysis methods for large space structures
Advances in continuum modeling, progress in reduction methods, and analysis and modeling needs for large space structures are covered with specific attention given to repetitive lattice trusses. As far as continuum modeling is concerned, an effective and verified analysis capability exists for linear thermoelastic stress, birfurcation buckling, and free vibration problems of repetitive lattices. However, application of continuum modeling to nonlinear analysis needs more development. Reduction methods are very effective for bifurcation buckling and static (steady-state) nonlinear analysis. However, more work is needed to realize their full potential for nonlinear dynamic and time-dependent problems. As far as analysis and modeling needs are concerned, three areas are identified: loads determination, modeling and nonclassical behavior characteristics, and computational algorithms. The impact of new advances in computer hardware, software, integrated analysis, CAD/CAM stems, and materials technology is also discussed.
Noor, A. K.↗
Bubble motion in a rotating liquid body
The behavior of a single gas bubble inside a rotating liquid-filled sphere has been investigated analytically and experimentally as part of ground-based investigations aimed at aiding in the design and interpretation of Shuttle experiments. In the analysis, a quasi-static description of the motion of a bubble was developed in the limit of small values of the Taylor number. A series of rotation experiments using air bubbles and silicone oils were designed to match the conditions specified in the analysis, i.e., the bubble size, sphere rotation rate, and liquid kinematic viscosity were chosen such that the Taylor number was much less than unity. The analytical description predicts the bubble velocity and its asymptotic location. It is shown that the asymptotic position is removed from the axis of rotation.
Annamalai, P.↗
A meshing framework for digital twins for extrusion based additive manufacturing
Additive manufacturing (AM) allows for manufacturing of complex three-dimensional geometries not typically realizable with standard manufacturing practices. The internal microstructure of AM components has a significant impact on mechanical, vibrational, and shock properties and permits richer design space when this is controllable. Due to complex interactions of internal geometry of an extrusion-based AM component, it is common practice to assume homogeneous behavior or to perform characterization testing on specific toolpath configurations. To avoid testing or material waste, it is necessary to develop a consistently accurate numerical simulation framework with relevant boundary value problems that can handle the complicated geometry of internal material microstructure present in AM components. Herein, a framework is proposed to directly create computational meshes suitable for finite element analysis (FEA) of the fine-scale features generated from extrusion-based AM tool paths to maintain a strong process–structure–property-performance linkage. This mesh can be manually or automatically analyzed using standard FEA simulations such as quasi-static preloading or modal analysis. The framework allows an in-silico assessment of a target AM geometry where fine-scale features greatly impact quantities of design interest such as in soft elastomeric lattices where toolpath infill can greatly influence the self-contact of a structure in compression, which we use as a motivating exemplar. This approach greatly reduces both time and resource waste present in traditional build and test design cycles for non-intuitive design spaces, and acts as a tool for use in the production of a key component of a digital twin, a mesh suitable for finite element analysis. In conclusion, it also further allows for the exploration of toolpath infill to optimize component properties beyond simple linear properties such as density and stiffness.
Additive manufacturing↗
A Procedure for Modeling Structural Component/Attachment Failure Using Transient Finite Element Analysis
Structures often comprise smaller substructures that are connected to each other or attached to the ground by a set of finite connections. Under static loading one or more of these connections may exceed allowable limits and be deemed to fail. Of particular interest is the structural response when a connection is severed (failed) while the structure is under static load. A transient failure analysis procedure was developed by which it is possible to examine the dynamic effects that result from introducing a discrete failure while a structure is under static load. The failure is introduced by replacing a connection load history by a time-dependent load set that removes the connection load at the time of failure. The subsequent transient response is examined to determine the importance of the dynamic effects by comparing the structural response with the appropriate allowables. Additionally, this procedure utilizes a standard finite element transient analysis that is readily available in most commercial software, permitting the study of dynamic failures without the need to purchase software specifically for this purpose. The procedure is developed and explained, demonstrated on a simple cantilever box example, and finally demonstrated on a real-world example, the American Airlines Flight 587 (AA587) vertical tail plane (VTP).
Lovejoy, Andrew E.↗
Flight Dynamics of an Aeroshell Using an Attached Inflatable Aerodynamic Decelerator
An aeroelastic analysis of the behavior of an entry vehicle utilizing an attached inflatable aerodynamic decelerator during supersonic flight is presented. The analysis consists of a planar, four degree of freedom simulation. The aeroshell and the IAD are assumed to be separate, rigid bodies connected with a spring-damper at an interface point constraining the relative motion of the two bodies. Aerodynamic forces and moments are modeled using modified Newtonian aerodynamics. The analysis includes the contribution of static aerodynamic forces and moments as well as pitch damping. Two cases are considered in the analysis: constant velocity flight and planar free flight. For the constant velocity and free flight cases with neutral pitch damping, configurations with highly-stiff interfaces exhibit statically stable but dynamically unstable aeroshell angle of attack. Moderately stiff interfaces exhibit static and dynamic stability of aeroshell angle of attack due to damping induced by the pitch angle rate lag between the aeroshell and IAD. For the free-flight case, low values of both the interface stiffness and damping cause divergence of the aeroshell angle of attack due to the offset of the IAD drag force with respect to the aeroshell center of mass. The presence of dynamic aerodynamic moments was found to influence the stability characteristics of the vehicle. The effect of gravity on the aeroshell angle of attack stability characteristics was determined to be negligible for the cases investigated.
Cruz, Juan R.↗