SEARCH · Engineering Papers

Results for “Stack Design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

All sources NASA NTRS DOE OSTI

NASA NTRS1995

Effects of Yarn Crimping on Braided Composite Design Allowables

Braided composite materials are currently being evaluated for wing skin stiffeners on commercial aircraft. These carbon-fiber/epoxy materials allow for low-cost manufacturing while maintaining high strength-to-weight and stiffness-to-weight ratios. The proposed braid architecture consists of axial carbon fiber yarns and braider carbon fiber yarns making 60 deg to 70 deg angles with respect to the axial yarns. These 2-D triaxial braids are produced as long, continuous tubes, which are flattened, cut, and stacked to produce the desired part thickness and shape. When infiltrated with epoxy resin and cured under a compaction pressure, the fiber yarns become crimped, allowing for higher fiber packing. Although high fiber packing is desirable, yarn crimping (especially in the axial fiberyarns) is undesirable. Significant axial yarn crimp angles (greater than 10 deg) have been measured in braided composites. Comparable levels of crimping have been found to produce significant compressive strength reductions in laminated composites consisting of planar fiber sheets. Thus, axial yarn crimping is suspected of producing significant reductions in compressive strength allowables for braided composites. The objective of this research is to quantify the reduction in compressive strength as a function of axial yarn crimp severity. Since crimp severity can be reduced by lowering the compaction pressure during curing, the resulting compressive strengths may be used to determine optimum processing conditions. A 'cure-on-the-loom' manufacturing process was developed to produce braided composites with controlled levels of crimping. This method allowed for controlled levels of tension to be placed on the axial yarns and maintained during the curing process. With increasing tension, the crimp severity in the axial yarns was reduced. Thus, varying crimp severities were produced ranging from conventional levels (greater than 10 deg) to virtually straight axial yarns. Test results indicate that a 30% increase in compressive strength is obtainable by eliminating axial yarn crimping. Further compression testing is underway to quantify the relationship between crimp severity and compressive strength. Additional testing is planned to investigate the effect of crimping on the open-hole compressive strength, often considered a more significant design allowable.

Adams, Dan↗

NASA NTRS2008

Ares I-X Flight Test Vehicle Similitude to the Ares I Crew Launch Vehicle

The Ares I-X Flight Test Vehicle is the first in a series of flight test vehicles that will take the Ares I Crew Launch Vehicle design from development to operational capability. The test flight is scheduled for April 2009, relatively early in the Ares I design process so that data obtained from the flight can impact the design of Ares I before its Critical Design Review. Because of the short time frame (relative to new launch vehicle development) before the Ares I-X flight, decisions about the flight test vehicle design had to be made in order to complete analysis and testing in time to manufacture the Ares I-X vehicle hardware elements. This paper describes the similarities and differences between the Ares I-X Flight Test Vehicle and the Ares I Crew Launch Vehicle. Areas of comparison include the outer mold line geometry, aerosciences, trajectory, structural modes, flight control architecture, separation sequence, and relevant element differences. Most of the outer mold line differences present between Ares I and Ares I-X are minor and will not have a significant effect on overall vehicle performance. The most significant impacts are related to the geometric differences in Orion Crew Exploration Vehicle at the forward end of the stack. These physical differences will cause differences in the flow physics in these areas. Even with these differences, the Ares I-X flight test is poised to meet all five primary objectives and six secondary objectives. Knowledge of what the Ares I-X flight test will provide in similitude to Ares I as well as what the test will not provide is important in the continued execution of the Ares I-X mission leading to its flight and the continued design and development of Ares I.

Huebner, Lawrence D.↗

NASA NTRS1987

Magnetically suspended stacks for inertial energy storage flywheel

A magnetically suspended flywheel stack based on a 'pancake' magnetic bearing stack is proposed for a 500 watt-hour energy storage system. Backup ball bearings in the system configuration both prevent damage to the system whenever there is a loss of magnetic suspension due to excessive outside disturbances, and insure that the fywheel stays within the linear control range. Design tools to investigate the performance of the control system and the magnetic circuits are also discussed.

Anand, Davinder K.↗

NASA NTRS1990

Scaling effects in the static and dynamic response of graphite-epoxy beam-columns

Scale model technology represents one method of investigating the behavior of advanced, weight-efficient composite structures under a variety of loading conditions. It is necessary, however, to understand the limitations involved in testing scale model structures before the technique can be fully utilized. These limitations, or scaling effects, are characterized. in the large deflection response and failure of composite beams. Scale model beams were loaded with an eccentric axial compressive load designed to produce large bending deflections and global failure. A dimensional analysis was performed on the composite beam-column loading configuration to determine a model law governing the system response. An experimental program was developed to validate the model law under both static and dynamic loading conditions. Laminate stacking sequences including unidirectional, angle ply, cross ply, and quasi-isotropic were tested to examine a diversity of composite response and failure modes. The model beams were loaded under scaled test conditions until catastrophic failure. A large deflection beam solution was developed to compare with the static experimental results and to analyze beam failure. Also, the finite element code DYCAST (DYnamic Crash Analysis of STructure) was used to model both the static and impulsive beam response. Static test results indicate that the unidirectional and cross ply beam responses scale as predicted by the model law, even under severe deformations. In general, failure modes were consistent between scale models within a laminate family; however, a significant scale effect was observed in strength. The scale effect in strength which was evident in the static tests was also observed in the dynamic tests. Scaling of load and strain time histories between the scale model beams and the prototypes was excellent for the unidirectional beams, but inconsistent results were obtained for the angle ply, cross ply, and quasi-isotropic beams. Results show that valuable information can be obtained from testing on scale model composite structures, especially in the linear elastic response region. However, due to scaling effects in the strength behavior of composite laminates, caution must be used in extrapolating data taken from a scale model test when that test involves failure of the structure.

Jackson, Karen E.↗

NASA NTRS1991

GaAs (AlGaAs)/CuInSe2 tandem solar cells. Technology status and future directions

Mechanically stacked, high efficiency, lightweight, and radiation resistant photovoltaic cells based on a GaAs thin film top and CuInSe2 thin film bottom cells were developed, and are considered one of the most promising devices for planar solar array applications. The highest efficiency demonstrated so far using the 4 sq cm design is 23.1 pct. AM0, one sun efficiency when measured in four-terminal configuration. The current status of the GaAs(AlGaAs)/CuInSe2 tandem cell program is presented and future directions that will lead to cell efficiencies higher than 26 pct. Air Mass Zero (AM0). A new 8 sq cm cell design developed for a two terminal and voltage matched configuration to minimize wiring complexity is discussed. Optimization of the GaAs structure for a higher end-of-life performance and further improvement of tandem cells by utilizing AlGaAs as an top absorber are described. Results of environmental tests conducted with these thin film GaAs/CuInSe2 tandem cells are also summarized.

Kim, N. P.↗

NASA NTRS2016

Manufacturing Challenges and Benefits When Scaling the HIAD Stacked-Torus Aeroshell to a 15 Meter Class System

Over a decade of work has been conducted in the development of NASA's Hypersonic Inflatable Aerodynamic Decelerator (HIAD) deployable aeroshell technology. This effort has included multiple ground test campaigns and flight tests culminating in the HIAD project's second generation (Gen-2) aeroshell system. The HIAD project team has developed, fabricated, and tested stacked-torus inflatable structures (IS) with flexible thermal protection systems (F-TPS) ranging in diameters from 3-6 meters, with cone angles of 60 and 70 degrees. To meet NASA and commercial near-term objectives, the HIAD team must scale the current technology up to 12-15 meters in diameter. Therefore, the HIAD project's experience in scaling the technology has reached a critical juncture. Growing from a 6-meter to a 15-meter class system will introduce many new structural and logistical challenges to an already complicated manufacturing process. Although the general architecture and key aspects of the HIAD design scale well to larger vehicles, details of the technology will need to be reevaluated and possibly redesigned for use in a 15-meter-class HIAD system. These include: layout and size of the structural webbing that transfers load throughout the IS, inflatable gas barrier design, torus diameter and braid construction, internal pressure and inflation line routing, adhesives used for coating and bonding, and F-TPS gore design and seam fabrication. The logistics of fabricating and testing the IS and the F-TPS also become more challenging with increased scale. Compared to the 6-meter aeroshell (the largest HIAD built to date), a 12-meter aeroshell has four times the cross-sectional area, and a 15-meter one has over six times the area. This means that fabrication and test procedures will need to be reexamined to account for the sheer size and weight of the aeroshell components. This will affect a variety of steps in the manufacturing process, such as: stacking the tori during assembly, stitching the structural webbing, initial inflation of tori, and stitching of F-TPS gores. Additionally, new approaches and hardware will be required for handling and ground testing of both individual tori and the fully assembled HIADs. There are also noteworthy benefits of scaling up the HIAD aeroshell to a 15m-class system. Two complications in working with handmade textile structures are the non-linearity of the material components and the role of human accuracy during fabrication. Larger, more capable, HIAD structures should see much larger operational loads, potentially bringing the structural response of the material components out of the non-linear regime and into the preferred linear response range. Also, making the reasonable assumption that the magnitude of fabrication accuracy remains constant as the structures grow, the relative effect of fabrication errors should decrease as a percentage of the textile component size. Combined, these two effects improve the predictive capability and the uniformity of the structural response for a 12-15-meter HIAD. In this presentation, a handful of the challenges and associated mitigation plans will be discussed, as well as an update on current manufacturing and testing that addressing these challenges.

Infatables↗

NASA NTRS2011

NASA Glenn Research Center's Fuel Cell Stack, Ancillary and System Test and Development Laboratory

At the NASA Glenn Research Center, a fully operational fuel cell test and evaluation laboratory is available which is capable of evaluating fuel cell components and systems for future NASA missions. Components and subsystems of various types can be operated and monitored under a variety of conditions utilizing different reactants. This fuel cell facility can test the effectiveness of various component and system designs to meet NASA's needs.

Loyselle, Patricia L.↗

NASA NTRS1988

Structural tailoring of high-speed turbine blades (SSME/STAEBL)

Space shuttle main engine (SSME) blades are subject to severe thermal, pressure, and forced vibration environments. Structural optimization provides an automated alternative to time consuming iterations. Any number of analyses, design variables, and constraints can be incorporated in a structural optimization computer code. This idea was applied to develop the code SSME/STAEBL, which is a stand alone code suitable for automated design of SSME turbopump blades. Additions and modifications of STAEBL included in SSME/STAEBL include the following: (1) thermal stress analysis, (2) gas dynamic (pressure) loads, (3) temperature-dependent material and thermal properties, (4) forced vibrations, (5) tip displacement constraints, (6) single crystal material analysis, (7) blade cross-section stacking offsets, and (8) direct time integration algorithm for transient dynamic response.

Rubinstein, Robert↗

NASA NTRS2002

Low Power Transceiver

One of the FREESTAR experiments, the Low Power Transceiver (LPT) experiment is a low-power, lightweight software programmable transceiver prototype technology demonstration that is being developed by NASA as a low-cost S-band spacecraft navigation and communication device. The LPT prototype receives Global Positioning System (GPS) satellite signals for spacecraft navigation support and provides both forward and return, low-rate data communications links to the Merritt Island (MILA) and Dryden Flight Research Facility (DFRC) ground stations and to the Tracking and Data Relay Satellite System (TDRSS). The experiment is designed to demonstrate the system's ability to do simultaneous communications and navigation, as well as multi-mode communications and reconfiguration. LPT is managed by NASA's Goddard Space Flight Center and sponsored by NASA/HQ Code M. The LPT experiment consists of one thermally conductive box containing the electronics stack, three S-band antennas and one L-band antenna. The LPT payload uses general Orbiter services, including power control, command, and telemetry provided through the HHC avionics. On-orbit, the LPT payload will be primarily operated via direct communications between LPT and ground stations (MILA, WLPS, or DFRC) and/or TDRSS, with backup command and telemetry capability provided via the hitchhiker avionics and remote Payload Operations Control Center. During operations, LPT will utilize high Sband frequencies for communications. The LPT TDRSS (and GN) forward link (uplink) frequency is 2106.40625 MHz and their TDRSS (and GN) return link (downlink) frequency is 2287.5 MHz (utilizing Left-handed Circular Polarization to work with the TDRSS MA system). Two standard switch panel switches will be utilized to prohibit inadvertent operation of the antenna. An additional inhibit will be provided through the HH avionics power relay to the LPT.

Source record↗

NASA NTRS2005

CHAMP (Camera, Handlens, and Microscope Probe)

CHAMP (Camera, Handlens And Microscope Probe)is a novel field microscope capable of color imaging with continuously variable spatial resolution from infinity imaging down to diffraction-limited microscopy (3 micron/pixel). As a robotic arm-mounted imager, CHAMP supports stereo imaging with variable baselines, can continuously image targets at an increasing magnification during an arm approach, can provide precision rangefinding estimates to targets, and can accommodate microscopic imaging of rough surfaces through a image filtering process called z-stacking. CHAMP was originally developed through the Mars Instrument Development Program (MIDP) in support of robotic field investigations, but may also find application in new areas such as robotic in-orbit servicing and maintenance operations associated with spacecraft and human operations. We overview CHAMP'S instrument performance and basic design considerations below.

robotic field investigations↗

NASA NTRS2010

Lessons Learned in Launching Ares I-X

The Ares I-X flight test, scheduled for 2009, is the first opportunity for the Constellation Program and Ares Projects to obtain important data on the in-flight loads, first stage recovery, and ground-handling characteristics of the Ares I crew launch vehicle. The flight test vehicle will incorporate a mix of flight and mockup hardware, reflecting an acceptable representation of the mass and outer mold line characteristics of the operational Ares I vehicle. It will be powered by a four-segment solid rocket motor from the Space Shuttle inventory and will include a fifth, inert spacer segment and new forward structures to make it the same shape as the Ares I first stage. The vehicle also includes mass simulators for the upper stage, Orion crew module, and launch abort system to match the outer mold line of Ares I; an active roll control system; and avionics derived from Shuttle and Atlas hardware. This suborbital mission will take the flight test vehicle from stacking in the Vehicle Assembly Building (VAB) at Kennedy Space Center (KSC) through liftoff, maximum dynamic pressure, first stage separation, and recovery. Ares I-X presented NASA with unique project management challenges. This presentation will address those unique challenges, including managing a virtual nationwide team under a constrained timeline; designing and building the launch vehicle and ground systems; working concurrently with Space Shuttle activities; and integrating technical and management functions. It also will identify key data collected and lessons learned from the flight that will be applied to future exploration missions.

Davis, Stephan R.↗

NASA NTRS1991

Thermal modeling of nickel-hydrogen battery cells operating under transient orbital conditions

An analytical study of the thermal operating characteristics of nickel-hydrogen battery cells is presented. Combined finite-element and finite-difference techniques are employed to arrive at a computationally efficient composite thermal model representing a series-cell arrangement operating in conjunction with a radiately coupled baseplate and coldplate thermal bus. An aggressive, low-mass design approach indicates that thermal considerations can and should direct the design of the thermal bus arrangement. Special consideration is given to the potential for mixed conductive and convective processes across the hydrogen gap. Results of a compressible flow model are presented and indicate the transfer process is suitably represented by molecular conduction. A high-fidelity thermal model of the cell stack (and related components) indicates the presence of axial and radial temperature gradients. A detailed model of the thermal bus reveals the thermal interaction of individual cells and is imperative for assessing the intercell temperature gradients.

Schrage, Dean S.↗

NASA NTRS2004

Performance of a Fuel-Cell-Powered, Small Electric Airplane Assessed

Rapidly emerging fuel-cell-power technologies may be used to launch a new revolution of electric propulsion systems for light aircraft. Future small electric airplanes using fuel cell technologies hold the promise of high reliability, low maintenance, low noise, and - with the exception of water vapor - zero emissions. An analytical feasibility and performance assessment was conducted by NASA Glenn Research Center's Airbreathing Systems Analysis Office of a fuel-cell-powered, propeller-driven, small electric airplane based on a model of the MCR-01 two-place kitplane (Dyn'Aero, Darois, France). This assessment was conducted in parallel with an ongoing effort by the Advanced Technology Products Corporation and the Foundation for Advancing Science and Technology Education. Their project - partially funded by a NASA grant - is to design, build, and fly the first manned, continuously propelled, nongliding electric airplane. In our study, an analytical performance model of a proton exchange membrane (PEM) fuel cell propulsion system was developed and applied to a notional, two-place light airplane modeled after the MCR-01 kitplane. The PEM fuel cell stack was fed pure hydrogen fuel and humidified ambient air via a small automotive centrifugal supercharger. The fuel cell performance models were based on chemical reaction analyses calibrated with published data from the fledgling U.S. automotive fuel cell industry. Electric propeller motors, rated at two shaft power levels in separate assessments, were used to directly drive a two-bladed, variable-pitch propeller. Fuel sources considered were compressed hydrogen gas and cryogenic liquid hydrogen. Both of these fuel sources provided pure, contaminant-free hydrogen for the PEM cells.

Berton, Jeffrey J.↗

NASA NTRS2008

Apparatus for Sampling Surface Contamination

An apparatus denoted a swab device has been developed as a convenient means of acquiring samples of contaminants from surfaces and suspending the samples in liquids. (Thereafter, the liquids can be dispensed, in controlled volumes, into scientific instruments for analysis of the contaminants.) The swab device is designed so as not to introduce additional contamination and to facilitate, simplify, and systematize the dispensing of controlled volumes of liquid into analytical instruments. The swab device is a single apparatus into which are combined all the equipment and materials needed for sampling surface contamination. The swab device contains disposable components stacked together on a nondisposable dispensing head. One of the disposable components is a supply cartridge holding a sufficient volume of liquid for one complete set of samples. (The liquid could be clean water or another suitable solvent, depending on the application.) This supply of liquid is sealed by Luer valves. At the beginning of a sampling process, the user tears open a sealed bag containing the supply cartridge. A tip on the nondisposable dispensing head is engaged with a Luer valve on one end of the supply cartridge and rotated, locking the supply cartridge on the dispensing head and opening the valve. The swab tip includes a fabric swab that is wiped across the surface of interest to acquire a sample. A sealed bag containing a disposable dispensing tip is then opened, and the swab tip is pushed into the dispensing tip until seated. The dispensing head contains a piston that passes through a spring-loaded lip seal. The air volume displaced by this piston forces the liquid out of the supply cartridge, over the swab, and into the dispensing tip. The piston is manually cycled to enforce oscillation of the air volume and thereby to cause water to flow to wash contaminants from the swab and cause the resulting liquid suspension of contaminants to flow into the dispensing tip. After several cycles to ensure adequate mixing, liquid containing the suspended contaminant sample is dispensed. The disposable components are then removed from the dispensing head, which may then be reused with a fresh set of disposable components.

Wells, Mark↗

NASA NTRSDate not supplied

DiskSat: Demonstration Mission for a Two-Dimensional Satellite Architecture

The DiskSat is a quasi-two-dimensional satellite bus architecture designed for applications requiring high power, large apertures, and/or high maneuverability in a low-mass satellite. A representative DiskSat structure is a composite flat panel, one meter in diameter and 2.5 cm thick. The volume is almost 20 liters, equivalent to a hypothetical 20U CubeSat, while the structural mass is less than 3 kg. The surface area is large enough to host over 200 W of solar cells without deployable solar panels. For launch, multiple DiskSats are stacked in a fully enclosed container/deployer using a simple mechanical interface and are released individually in orbit. The Aerospace Corporation, with the support of the NASA Space Technology Mission Directorate (STMD), is preparing a flight of four DiskSats for launch in 2024 to demonstrate the feasibility of both the dispenser and the DiskSat bus. In addition, the flight is expected to demonstrate several features of the DiskSat including the unprecedented high power-to-mass ratio, the maneuverability of the bus using low-thrust electric propulsion, and the ability to fly continuously in a low-drag orientation, enabling operations in very low Earth orbits (VLEO). The DiskSats will be launched in and deployed from a dispenser that provides a containerized rideshare environment; the dispenser fully encloses the DiskSats during launch and then opens to dispense the satellites one at a time once in orbit. The dispenser is modular in design and expandable from the capacity of four DiskSats for this flight to as many as 20 DiskSats for future flights. NASA STMD seeks disruptive and innovative technologies that could help lead to the next-generation systems for future science and exploration missions. DiskSat is a potentially disruptive technology leading to new, enabling architectures using ever-more capable small spacecraft. Data generated from this flight will inform the drafting of a DiskSat standard intended to encourage easy and frequent access to space, in the same manner as the CubeSat standard. DiskSat is expected to become a standard format for rideshare-compatible, high-power, maneuverable, low-mass satellites for Earth-orbit, cis-lunar, and deep space applications.

Richard Welle↗

NASA NTRS2001

Structural Qualification Testing of the WindSat Payload Using Sine Bursts Near Structural Resonance

Sine burst tests are often used for structural qualification of space flight hardware. In most instances, the driving frequency of the shaker is specified far below the structure's first resonant mode, such that the entire test article sees uniform acceleration. For large structures, this limits qualification testing to lower parts of the structure, or else it over-tests the lower structure to achieve qualification of the upper structure. The WindSat payload, a 10.5 foot tall graphite/epoxy, titanium, and aluminum radiometer, experiences accelerations at the six foot diameter reflector nearly four times that at the spacecraft interface. Due to size of the payload, the number of bonded joints, and the lightweight reflector support structure design and construction, using static pull testing to qualify all of the bonded joints in the upper structure would result in large, expensive, and extensive test fixturing. Sine burst testing near the first two structural resonant modes was performed on the WindSat payload to achieve the correct load factor distribution up the stack for structural qualification. In this presentation, how finite element method (FEM) sine burst predictions were used in conjunction with low level random and sine burst tests to achieve correct qualification test load factor distribution on the WindSat payload is discussed. Also presented is the risk mitigation approach for using the uncorrelated FEM in this procedure.

Pontius, Jim↗

NASA NTRS2007

Cohesive Elements for Shells

A cohesive element for shell analysis is presented. The element can be used to simulate the initiation and growth of delaminations between stacked, non-coincident layers of shell elements. The procedure to construct the element accounts for the thickness offset by applying the kinematic relations of shell deformation to transform the stiffness and internal force of a zero-thickness cohesive element such that interfacial continuity between the layers is enforced. The procedure is demonstrated by simulating the response and failure of the Mixed Mode Bending test and a skin-stiffener debond specimen. In addition, it is shown that stacks of shell elements can be used to create effective models to predict the inplane and delamination failure modes of thick components. The results indicate that simple shell models can retain many of the necessary predictive attributes of much more complex 3D models while providing the computational efficiency that is necessary for design.

Davila, Carlos G.↗

NASA NTRS2007

Effective Simulation of Delamination in Aeronautical Structures Using Shells and Cohesive Elements

Davila, Carlos G.↗