Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Stabilization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Generalized Predictive Control for Active Stability Augmentation and Vibration Reduction on an Aeroelastic Tiltrotor Model

Tiltrotor aircraft are defining the state-of-the-art in vertical lift technology as they have the potential to greatly expand rotary-wing operational boundaries. However, they are often limited in forward flight speed due to complex coupled rotor and wing dynamic instabilities. The U.S. Army and NASA have been developing a new wind tunnel model, the TiltRotor Aeroelastic Stability Testbed(TRAST), to test proprotors in the NASA Langley Research Center Transonic Dynamics Tunnel (TDT) to investigate aeroelastic stability in cruise. The test is intended to provide high-quality research data for analytical tool development and validation. In addition, the TRAST model will support, develop, and mature new technologies for the design of advanced proprotor aircraft. Stability augmentation and vibration reduction during testing is planned with the use of an active control methodology known as Generalized Predictive Control(GPC). GPC is an autoregressive control law that experimentally acquires a system identification to derive the input-output relation of controls and corresponding sensors. This type of control law is especially useful for complex dynamic interactions that are difficult to explicitly model such as proprotor pylon instability, often referred to as whirl flutter. GPC has been successfully employed on other tiltrotor vehicles to suppress whirl flutter instabilities and vibrations. To aid in the characterization of the wind-tunnel model and in tool development, an analytical representation of the wind-tunnel model was developed using the rotorcraft comprehensive analysis system (RCAS) that simulates structural dynamics and aerodynamics. RCAS was used to derive state-space estimates of the physical plant at various flight conditions to test control law effectiveness. This paper will present an overview of the test article development, a description of RCAS, an explanation of the GPC methodology, and results of GPC being applied to state-space plant estimates of the TRAST model. In these simulations, GPC was effective at stabilizing the aircraft beyond the whirl-flutter boundary while simultaneously reducing vibrations across the flight regime. Additionally, a modern advancement to GPC, termed advanced GPC (AGPC), is introduced that enables a self-adapting system identification. Preliminary results show that AGPC is successful at self-correction as the plant changes from what was used for system identification.

tiltrotor↗

Long Term Stability Monitoring of Aqua MODIS Thermal Emissive Bands through Radiative Transfer Modeling

Moderate Resolution Imaging Spectroradiometer (MODIS) on Aqua has been in operation providing continuous global observations for science research and applications since 2002. The long-term stability of thermal emissive bands (TEBs) of Aqua MODIS was monitored through inter-comparisons with measurements by hyperspectral infrared sensors, such as AIRS on Aqua and IASI on MetOp satellite, or through long term vicarious monitoring over cold targets, such as Dome- C and deep convective clouds (DCC). In this paper, a radiative transfer modeling-based simulation model using Community Radiative Transfer Model (CRTM) is developed to perform the long-term monitoring of the stability of TEBs of Aqua MODIS. CRTM is a fast-radiative transfer model for calculations of radiances for satellite infrared radiometers and is able to output infrared radiance and brightness temperature at spectral bands of MODIS. Long term European Centre for Medium-Range Weather Forecasts (ECMWF) global atmospheric reanalysis data, such as temperature and humidity profiles, are used as inputs to the CRTM simulation. By confining the area of interest to be over low to middle latitude ocean, the long-term stabilities of selected Aqua MODIS TEBs are monitored through Observation–Background (O-B) brightness temperature (BT) bias between MODIS measurements and BT retrieval from CRTM simulation. The consistency and relative stability between Aqua MODIS and ECMWF reanalysis data for surface channels of MODIS are evaluated. In addition, the radiative transfer modeling with CRTM enables us to evaluate the impacts of long term variation of global CO2 distribution on the O-B BT biases for CO2 channels of Aqua MODIS through comparison of simulations with constant or long term variable CO2 as inputs. The O-B analysis with RTM show that Aqua MODIS surface channels are all radiometrically stable with yearly BT bias drift less than 0.004K/year for B20, B22, B23 and ~0.01K/year for B31 and B32. The CO2 absorption channels of Aqua MODIS, e.g. B33-B36, are stable with BT bias drift < 0.005K/year.

MODIS↗

On the Stability and Phase Behavior of Titan's Subsurface Liquid Columns

On Titan, liquid hydrocarbon may stay in the subsurface porous permeable crust known as the alkanofer, analogous to water in Earth’s aquifer. In addition to pressure gradient, the subsurface liquid in alkanofers is subject to vertical compositional grading due to the gravity and temperature gradient. The common wisdom is that the liquid would normally stay underground in a stability established by the pressure that increases with depth as observed in aquifers on Earth. However, Titan’s liquids consist of nitrogen and hydrocarbons, mainly methane and ethane, the behavior of which is very sensitive to temperature and pressure. Consequently, the liquid density does not always increase with depth, thus may introduce a reverse density profile that leads to vertical convective instability of the liquid column. If reverse density profiles are present, capillary pressures arising from liquid trapped within small pores in the crust can help with the column stability. The liquid held in the capillaries can seal the space below it thus helping with the stability, unless the overpressure built from underneath becomes larger than the capillary pressure, which causes leakage to allow the liquids to seep upward from the deep. This situation is analogous to hydrocarbon seeps on Earth, where oil and natural gas escape the reservoir and flow slowly through network of cracks to the surface. An algorithm based on an extended Gibbs equation commonly used in petroleum reservoir engineering is employed in this work to produce pressure, density, and compositional profiles for evaluating the stability and phase behavior of Titan’s subsurface fluids.

Sugata Tan↗

Design of A Transition-Edge-Sensor-Based Thermal Stabilization Stage

Electrothermal feedback in a transition edge sensor suppresses thermal fluctuations in the TES and regions in close thermal contact. We designed a heavily-metallized, leg-isolated membrane with a TES which serves as a thermal stabilization stage that can be lithographically integrated with other devices. Through modeling, fabrication and test of prototype devices, we examine whether the noise reduction in this stage can reduce thermal fluctuations (e.g. 1/f noise) in the other components by providing a more stable base temperature. In one implementation, a leg-isolated TES bolometer of higher superconducting transition temperature (Tc) is encircled by a second membrane region which is metallized and thermally stabilized by a second, lower-Tc TES. We present fabrication results on the dual-Tc design and testing of the simultaneous biasing of a two-stage, two-TES device. We explore varied heat capacity of the thermally stabilized stage in the single pixel design. We also present other designs to evaluate the use of an outer thermal stabilization stage for multiple pixel arrangements.

Rachel Borrelli↗

An Examination of the Recent Stability of Ozonesonde Global Network Data

The recent Assessment of Standard Operating Procedures for OzoneSondes (ASOPOS 2.0; WMO/GAW Report #268) addressed questions of homogeneity and long-term stability in global electrochemical concentration cell (ECC) ozone sounding network time series. Among its recommendations was adoption of a standard for evaluating data quality in ozonesonde time series. Total column ozone (TCO) derived from the sondes compared to TCO from Aura’s Ozone Monitoring Instrument (OMI) is a primary quality indicator. Comparisons of sonde ozone with Aura’s Microwave Limb Sounder (MLS) are used to assess the stability of stratospheric ozone. This paper provides a comprehensive examination of global ozonesonde network data stability and accuracy since 2004 in light of the sudden post-2013 TCO “dropoff” of ~3-4% that was reported previously at select stations (Stauffer et al., 2020). Comparisons with Aura OMI TCO averaged across the network of 60 stations are stable within about ±2% over the past 18 years. Sonde TCO has similar stability compared to three other TCO satellite instruments, and the stratospheric ozone measurements average to within ±5% of MLS from 50 to 10 hPa. Thus, sonde data are reliable for trends, but with a caveat applied for a subset of dropoff stations in the tropics and subtropics. The dropoff is associated with only one of two major ECC instrument types. A detailed examination of ECC serial numbers pinpoints the timing of the dropoff. However, we find that overall, ozonesonde data are stable and accurate compared to independent measurements over the past two decades.

Ryan M. Stauffer↗

Algorithm Stability and the Long-Term Geospace Data Record from TIMED/SABER

The ability of satellite instruments to accurately observe long-term changes in atmospheric temperature depends on many factors including the absolute accuracy of the measurement, the stability of the calibration of the instrument, the stability of the satellite orbit, and the stability of the numerical algorithm that produces the temperature data. We present an example of algorithm instability recently discovered in the temperature dataset from the SABER instrument on the NASA TIMED satellite. The instability resulted in derived temperatures that were substantially colder than anticipated from mid-December 2019 to mid-2022. This algorithm-induced change in temperature over one to two years corresponded to the expected change over several decades from increasing anthropogenic CO2. This paper highlights the importance of algorithm stability in developing Geospace Data Records (GDRs) for Earth’s mesosphere and lower thermosphere. A corrected version (Version 2.08) of the temperatures from SABER is described.

M G Mlynczak↗

Eigenvalue Sensitivity Computations for Linear Stability Theory

To realize the drag reduction benefit of boundary-layer transition control strategies, it is crucial to integrate transition prediction into the vehicle design through an optimization process. The integration of transition prediction based on linear stability analysis into adjoint d design optimization requires coupling an adjoint enabled computational fluid dynamics (CFD) solver with an adjoint enabled linear stability code. In particular, the boundary-layer transition location is often predicted using the N-factor method based on linear stability theory (LST). Thus, sensitivity of the linear-stability eigenvalues constitute an essential building block for optimizing the laminar flow performance. The present paper describes an implementation of LST eigenvalue sensitivity analysis that can be easily coupled with a CFD solver. Specifically, we describe a discrete adjoint formulation for the transition location prediction based on the N-factor method. The verification of this formulation is carried out by comparing the adjoint-based sensitivity of the local growth rate of a given instability mode with respect to the disturbance frequency, and the adjoint-based sensitivity of the transition location with respect to spanwise wavenumber with those sensitivities computed using a finite-difference approximation. Finally, the adjoint LST formulation is applied to flat-plate boundary-layer flows at transonic, supersonic, and hypersonic conditions, to determine the behavior and sensitivities of the transition location with respect to a range of disturbance spanwise wavenumbers.

Boundary Layer Transition↗

Wind-tunnel Measurement of Propeller Whirl-flutter Speeds and Static-stability Derivatives and Comparison with Theory

Results of an experimental investigation of propeller whirl flutter are presented for a model consisting of an isolated, rigid system of propeller and simulated power plant mounted with flexibility in pitch and yaw on a rigid sting. A range of propeller blade angles, restraint stiffnesses, and restraint damping coefficients was investigated for a system symmetrical i n pitch and yaw with a windmilling propeller. Measurements of the static-stability derivatives were also made by using a simple balance and were compared with two sets of theoretical derivatives. Whirl-flutter calculations were made with the theoretical and measured derivatives. Some limited results were obtained for the whirl flutter of the model mounted on a cantilever semispan wing. The measured whirl-flutter speeds and frequencies of the isolated model were in very good agreement with those predicted by calculations in which measured derivatives and viscous damping were used. This agreement was better than that obtained by using structural damping. Predicted whirl-flutter speeds for the isolated model were lower when theoretical stability derivatives were used than when measured derivatives were used. The theoretical and experimental static-stability derivatives exhibited the same trends, but in certain instances differed appreciably in magnitude. the measured whirl-flutter boundary for the one configuration considered.

PROPELLER↗

Investigation of the Influence of Fuselage and Tail Surfaces on Low-speed Static Stability and Rolling Characteristics of a Swept-wing Model

Results are presented of a wind-tunnel investigation to determine influence of the fuselage and tail on static stability and rotary derivatives in roll of a model having 45 degrees sweptback wing and tail surfaces. The wing alone and the model without the horizontal tail showed marginal longitudinal stability near maximum lift. The longitudinal stability of the complete model was satisfactory. The vertical tail produced larger increments of rate of change of lateral-force and yawing-moment coefficients with wing-tip helix angle than the fuselage or the horizontal tail.

TAIL-WING-FUSELAGE COMBINATIONS - AIRPLANES↗

Stability of elastically supported columns

A criterion is developed for the stiffness required of elastic lateral supports at the ends of a compression member to provide stability. A method based on this criterion is then developed for checking the stability of a continuous beam-column. A related method is also developed for checking the stability of a member of a pin-jointed truss against rotation in the plane of the truss.

COMPRESSION MEMBERS-STABILITY↗

Comparison of Wind-Tunnel and Flight Measurements of Stability and Control Characteristics of a Douglas A-26 Airplane

Tests in Langley pressure tunnel of model XA-26 bomber were compared with those of A-26B (twin-engine attack bomber) and showed that static longitudinal stability, indicated by elevator-fixed neutral points, and variation of elevator deflection in straight and turning flight were good. Airplane possessed improved stability at low speeds which was attributed to pronounced stalling at root of production wing. At rudder-force reversal at speeds higher than those in flight tests, agreement in rudder-fixed and rudder-free static directional stability was good. Hinge moment obtained at zero sideslip was satisfactory for determining aileron forces in sideslip.

SIDESLIPPING - DOUGLAS A-26↗

Signal Stabilization of Self-Oscillating Systems

The hunt (self-oscillations) of a physical system may often be removed by the introduction of an appropriate stabilizing signal which changed the open loop gain in a nonlinear manner. More generally, the performance of nonlinear systems in many cases may be improved by the introduction of extra signals. The theory of signal stabilization developed here extends the earlier work by Oldenburger and Liu involving an equivalent gain concept. It is shown that with the aid of the Fourier series the designer can determine the periodic signal to be inserted at one point in a loop to yield a desired stabilizing input to a nonlinear element in the loop. The use of sinusoidal and triangular inputs to a limiter are compared. An example where a limiter is the only nonlinearity is employed to illustrate the theory. The approach developed here explains experimental results previously reported by Oldenburger.

SELF-OSCILLATION↗

SOME SHELL STABILITY PROBLEMS IN MISSILE AND SPACE VEHICLE ANALYSIS

A brief discussion is presented of three structural shell stability studies in progress at Lockheed Missiles & Space Company: the stabilizing influence of solid propellants, the effect of cushion stiffness on buckling under cushion loading, and the snap-through buckling of axially loaded cylinders. Recent analytical results are compared with test data. Also included is a brief description of a few shell stability problems of present interest to LMSC for which satisfactory methods of analysis are not available.

MISSILE↗

Wind-Tunnel Investigation of Effects of Unsymmetrical Horizontal-Tail Arrangements on Power-on Static Longitudinal Stability of a Single-Engine Airplane Model

A wind-tunnel investigation has been made to determine the effects of unsymmetrical horizontal-tail arrangements on the power-on static longitudinal stability of a single-engine single-rotation airplane model. Although the tests and analyses showed that extreme asymmetry in the horizontal tail indicated a reduction in power effects on longitudinal stability for single-engine single-rotation airplanes, the particular "practical" arrangement tested did not show marked improvement. Differences in average downwash between the normal tail arrangement and various other tail arrangements estimated from computed values of propeller-slipstream rotation agreed with values estimated from pitching-moment test data for the flaps-up condition (low thrust and torque) and disagreed for the flaps-down condition (high thrust and torque). This disagreement indicated the necessity for continued research to determine the characteristics of the slip-stream behind various propeller-fuselage-wing combinations. Out-of-trim lateral forces and moments of the unsymmetrical tail arrangements that were best from consideration of longitudinal stability were no greater than those of the normal tail arrangement.

AIRFOILS - NACA 65(216-012(MOD ) - CHAR & MOMENTS ↗

An analysis of the effects of aeroelasticity on static longitudinal stability and control of a swept-back-wing airplane

A theoretical analysis of the effects of aeroelasticity on the stick-fixed static longitudinal stability and elevator angle required for balance of an airplane is presented together with calculated effects for a swept-wing bomber of relatively high flexibility. Although large changes in stability due to certain parameters are indicated for the example airplane, the over-all stability change after considering all parameters was quite small, compared to the individual effects, due to the counterbalancing of wing and tail contributions. The effect of flexibility on longitudinal control for the example airplane was found to be of little real importance.

STABILITY, LONGITUDINAL - STATIC↗

EO-1 Hyperion Reflectance Time Series at Calibration and Validation Sites: Stability and Sensitivity to Seasonal Dynamics

This study evaluated Earth Observing 1 (EO-1) Hyperion reflectance time series at established calibration sites to assess the instrument stability and suitability for monitoring vegetation functional parameters. Our analysis using three pseudo-invariant calibration sites in North America indicated that the reflectance time series are devoid of apparent spectral trends and their stability consistently is within 2.5-5 percent throughout most of the spectral range spanning the 12-plus year data record. Using three vegetated sites instrumented with eddy covariance towers, the Hyperion reflectance time series were evaluated for their ability to determine important variables of ecosystem function. A number of narrowband and derivative vegetation indices (VI) closely described the seasonal profiles in vegetation function and ecosystem carbon exchange (e.g., net and gross ecosystem productivity) in three very different ecosystems, including a hardwood forest and tallgrass prairie in North America, and a Miombo woodland in Africa. Our results demonstrate the potential for scaling the carbon flux tower measurements to local and regional landscape levels. The VIs with stronger relationships to the CO2 parameters were derived using continuous reflectance spectra and included wavelengths associated with chlorophyll content and/or chlorophyll fluorescence. Since these indices cannot be calculated from broadband multispectral instrument data, the opportunity to exploit these spectrometer-based VIs in the future will depend on the launch of satellites such as EnMAP and HyspIRI. This study highlights the practical utility of space-borne spectrometers for characterization of the spectral stability and uniformity of the calibration sites in support of sensor cross-comparisons, and demonstrates the potential of narrowband VIs to track and spatially extend ecosystem functional status as well as carbon processes measured at flux towers.

Calibration↗

Fuzzy Logic Controller Stability Analysis Using a Satisfiability Modulo Theories Approach

While many widely accepted methods and techniques exist for validation and verification of traditional controllers, at this time no solutions have been accepted for Fuzzy Logic Controllers (FLCs). Due to the highly nonlinear nature of such systems, and the fact that developing a valid FLC does not require a mathematical model of the system, it is quite difficult to use conventional techniques to prove controller stability. Since safety-critical systems must be tested and verified to work as expected for all possible circumstances, the fact that FLC controllers cannot be tested to achieve such requirements poses limitations on the applications for such technology. Therefore, alternative methods for verification and validation of FLCs needs to be explored. In this study, a novel approach using formal verification methods to ensure the stability of a FLC is proposed. Main research challenges include specification of requirements for a complex system, conversion of a traditional FLC to a piecewise polynomial representation, and using a formal verification tool in a nonlinear solution space. Using the proposed architecture, the Fuzzy Logic Controller was found to always generate negative feedback, but inconclusive for Lyapunov stability.

Fuzzy Logic Controller↗

Jet Fuel Thermal Stability Investigations Using Ellipsometry

Jet fuels are typically used for endothermic cooling in practical engines where their thermal stability is very important. In this work the thermal stability of Sasol IPK (a synthetic jet fuel) with varying levels of naphthalene has been studied on stainless steel substrates using spectroscopic ellipsometry in the temperature range 385-400 K. Ellipsometry is an optical technique that measures the changes in a light beam’s polarization and intensity after it reflects off of a thin film to determine the film’s thickness and optical properties. All of the tubes used were rated as thermally unstable by the color standard portion of the Jet Fuel Thermal Oxidation Test, and this was confirmed by the deposit thicknesses observed using ellipsometry. A new amorphous model on a stainless steel substrate was used to model the data and obtain the results. It was observed that, as would be expected, increasing the temperature of the tube increased the overall deposit amount for a constant concentration of naphthalene. The repeatability of these measurements was assessed using multiple trials of the same fuel at 385 K. Lastly, the effect of increasing the naphthalene concentration in the fuel at a constant temperature was found to increase the deposit thickness.In conclusion, ellipsometry was used to investigate the thermal stability of jet fuels on stainless steel substrate. The effects of increasing temperature and addition of naphthalene on stainless steel tubes with Sasol IPK fuel were investigated. It was found, as expected, that increasing temperature lead to an increase in deposit thickness. It wasAmerican Institute of Aeronautics and Astronautics6also found that increasing amounts of naphthalene increased the maximum deposit thickness. The repeatability of these measurements was investigated using multiple tests at the same conditions. The present work provides as a better quantitative tool compared to the widely used JFTOT technique. Future work will expand on the fuel types, temperature, and substrate materials.

thermal stability↗