Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SiC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Survey and Benchmark of Benefits of High Voltage SiC Applications in Medium Voltage Power Distribution Grids

The main objective of this survey and benchmark study is to identify and document potential high-impact applications in today's and future medium voltage (MV) distribution grids that will significantly benefit from high voltage (HV) (i.e. > 3.3 kV) SiC-based power electronics equipment. In particular, it is desirable to identify applications that can utilize the high switching speed and high control bandwidth enabled by SiC-based equipment. Specifically, the benefits of using SiC are quantified through the benchmark analysis and design using simulation for the selected high-impact applications. In addition, to provide grid support services, it is necessary to consider grid requirements in the grid-connected converter's design. Therefore, the impact of grid requirements on the HV SiC-based grid-connected converter is evaluated.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Beta-to-alpha transformation in polycrystalline SiC. II - Interfacial energetics

A phenomenological analysis of the energetics of the beta-to-alpha transformation in polycrystalline SiC is presented. It is found that the extreme anisotropy of the interfacial energy between alpha- and beta-SiC can account for the rapid growth of composite grains into the beta matrix during conventional sintering or hot-pressing processes. The composite grains consist of alpha-SiC plates 'sandwiched' between well-oriented and recrystallized beta-SiC 'envelopes'. The interfaces involving the 111 plane type of beta and (0001) of alpha have much lower energies than random beta/alpha interfaces.

Mitchell, T. E.↗

Compensation in epitaxial cubic SiC films

Hall measurements on four n-type cubic SiC films epitaxially grown by chemical vapor deposition on SiC substrates are reported. The temperature dependent carrier concentrations indicate that the samples are highly compensated. Donor ionization energies, E sub D, are less than one half the values previously reported. The values for E sub D and the donor concentration N sub D, combined with results for small bulk platelets with nitrogen donors, suggest the relation E sub D (N sub D) = E sub D(O) - alpha N sub N sup 1/3 for cubic SiC. A curve fit gives alpha is approx 2.6x10/5 meV cm and E sub D (O) approx 48 meV, which is the generally accepted value of E sub D(O) for nitrogen donors in cubic SiC.

Segall, B.↗

Dry etching of beta-SiC in CF4 and CF4 + O2 mixtures

Dry etching of cubic (100) beta-SiC single-crystal thin films produced via chemical-vapor deposition (CVD) has been performed in CF4 and CF4 + O2 mixtures, in both the reactive-ion-etching (RIE) and plasma-etching modes. The latter process yielded measurable etch rates, but produced a dark surface layer which appears, from the results of secondary-ion mass spectrometry, to be residual SiC. The RIE samples had no residual layer, but Auger electron spectroscopy did reveal a C-rich surface. The optimal RIE conditions were obtained with 10 sccm of pure CF4 at 40 mtorr and a power density of 0.548 W/sq cm, giving an etch rate of 23.3 nm/min. Neither the increase of temperature between 293 and 573 K, nor the incremental addition of O2 to CF4 to 50 percent, produced any strong effect on the etch rates of SiC during RIE. Pictorial evidence of fine line structures produced by RIE of beta-SiC films are also presented.

Palmour, J. W.↗

Corrosion pitting of SiC by molten salts

The corrosion of SiC by thin films of Na2CO3 and Na2SO4 at 1000 C is characterized by a severe pitting attack of the SiC substrate. A range of different Si and SiC substrates were examined to isolate the factors critical to pitting. Two types of pitting attack are identified: attack at structural discontinuities and a crater-like attack. The crater-like pits are correlated with bubble formation during oxidation of the SiC. It appears that bubbles create unprotected regions, which are susceptible to enhanced attack and, hence, pit formation.

Jacobson, N. S.↗

Thermal expansion and elastic anisotropies of SiC as related to polytype structure

The concept of the fraction of hexagonal stacking is used to describe the anisotropic thermal expansion coefficients of polytypes of SiC. The single crystal elastic anisotropy for the SiC polytype structures and the temperature dependencies of the anisotropies are examined. The anisotropic thermoelastic stress index for the 3C and 6H SiC polytypes are illustrated graphically. It is shown that this index is useful for predicting the most desirable crystal growth orientations for SiC whisker incorporation into composite matrices.

Li, Z.↗

Zirconia toughened SiC whisker reinforced alumina composites small business innovation research

The objective of this phase 1 project was to develop a ceramic composite with superior fracture toughness and high strength, based on combining two toughness inducing materials: zirconia for transformation toughening and SiC whiskers for reinforcement, in a controlled microstructure alumina matrix. The controlled matrix microstructure is obtained by controlling the nucleation frequency of the alumina gel with seeds (submicron alpha-alumina). The results demonstrate the technical feasibility of producing superior binary composites (Al2O3-ZrO2) and tertiary composites (Al2O3-ZrO2-SiC). Thirty-two composites were prepared, consolidated, and fracture toughness tested. Statistical analysis of the results showed that: (1) the SiC type is the key statistically significant factor for increased toughness; (2) sol-gel processing with a-alumina seed had a statistically significant effect on increasing toughness of the binary and tertiary composites compared to the corresponding mixed powder processing; and (3) ZrO2 content within the range investigated had a minor effect. Binary composites with an average critical fracture toughness of 6.6MPam sup 1/2, were obtained. Tertiary composites with critical fracture toughness in the range of 9.3 to 10.1 MPam sup 1/2 were obtained. Results indicate that these composites are superior to zirconia toughened alumina and SiC whisker reinforced alumina ceramic composites produced by conventional techniques with similar composition from published data.

Loutfy, R. O.↗

Interstellar SiC in the Murchison and Murray meteorites - Isotopic composition of Ne, Xe, Si, C, and N

Detailed ion-probe data are reported on Murchison and Murray C2 chondrites, along with noble-gas data on Murchison, with the purpose of characterizing the number and isotopic composition of independent SiC components and to link them to their stellar sources. Results show that coarse-grained and fine-grained SiC (totaling about 6-9 ppm of the two meteorites) contains record concentrations of two exotic components: Ne-E(H) (nearly monoisotopic Ne-22) and Se-S (enriched in isotopes 128, 130, and 132), respectively. The Ne-21 content was found to exceed up to 40-fold the content expected from the recent cosmic-ray irradiation, implying a presolar cosmic-ray exposure age of about 39 Ma. This age is much shorter that the predicted 500 Ma lifetime of refractory interstellar grains and implies either a selective interstellar destruction process for SiC, enhanced supernova activity in the protosolar neighborhood, or late outgassing of greater than 90 percent of the SiC.

Zinner, Ernst↗

Deep-level dominated electrical characteristics of Au contacts on beta-SiC

Electrical characteristics of Au contacts on beta-SiC films, grown epitaxially on both nominal and off-axis (100) silicon substrates, are reported. An analysis of the logarithmic I-V plots of the Au/beta-SiC diodes revealed information pertaining to the deep states present in the materials. It was found that while the beta-SiC films grown on nominally (100) oriented substrates show the presence of two deep levels located between 0.26 and 0.38 eV below the conduction bandedge, the beta-SiC films deposited on off-axis substrates have only one deep level, located about 0.49 eV below the conduction bandedge for the 2-deg off (100) substrates and 0.57 eV for the 4-deg off (100) substrates. The presence of the shallower deep states in the beta-SiC films grown on nominal (100) substrates is attributed to the electrical activity of antiphase domain boundaries.

Das, K.↗

Reactions of SiC with H2/H2O/Ar mixtures at 1300 C

Thermochemical modeling anticipates the existence of three reaction regions for the case of a sintered alpha-SiC with 5 percent H2/H2O/Ar at 1300 C, depending on the initial water vapor or, equivalently, oxygen, content of the gas stream. While a high oxygen content leads to SiC-protecting SiO2 surface film formation and limits consumption of the SiC through passive oxidation, intermediate oxygen contents lead to SiO and CO formation and rapid SiC consumption. In this intermediate region, reaction rates appear to be controlled by H2O gas-phase transport to the sample; reacted microstructures exhibit extensive grain-boundary attack in this region. Very low oxygen content is predicted to selectively remove carbon, with free silicon formation.

Jacobson, Nathan S.↗

Chemical compatibility issues related to use of copper as an interfacial layer for SiC fiber reinforced Ti3Ai+Nb composite

The reaction of Cu, a potential interfacial compliant layer for the Ti3Al plus Nb/SiC composite, with SiC, SCS-6 fiber, and the Ti3Al plus Nb matrix was examined at two temperatures: 1223 and 1273 K. Reaction of Cu with SiC resulted in the formation of a CuSi solution and free carbon, the reaction product being molten at 1273 K. Hot pressing the SCS-6 fiber in a Cu matrix at 1273 K resulted in cracking and delamination of the outer carbon-rich coating, thus allowing the Cu to penetrate to the SiC-carbon coating interface and react with SiC. In contrast, no such damage to the outer coating was observed at 1223 K. There was excessive reaction between Cu and the Ti3Al plus Nb matrix, the reaction product being molten both at 1223 and 1273 K. An interlayer of Nb between Cu and Ti3Al plus Nb matrix prevented the reaction between the two.

Misra, Ajay K.↗

Application of Oxidation to the Structural Characterization of Sic Epitaxial Films

Both 3C-SiC and 6H-SiC single-crystal films can be grown on vicinal (0001) 6H-SiC wafers. It is found that oxidation can be a powerful diagnostic process for (1) 'color mapping' the 3C and 6H regions of these films, (2) decorating stacking faults in the films, (3) enhancing the decoration of double positioning boundaries, and (4) decorating polishing damage. Contrary to previously published oxidation results, proper oxidation conditions can yield interference colors that provide a definitive map of the polytype distribution for both the Si face and C face of SiC films.

Powell, J. A.↗

High-voltage 6H-SiC p-n junction diodes

A chemical vapor deposition (CVD) process has been used to produce device structures of n- and p-type 6H-SiC epitaxial layers on commercially produced single-crystal 6H-SiC wafers. Mesa-style p-n junction diodes were successfully fabricated from these device structures using reactive ion etching, oxide passivation, and electrical contact metallization techniques. When tested in air, the 6H-SiC diodes displayed excellent rectification characteristics up to the highest temperature tested, 600 C. To observe avalanche breakdown of the p-n junction diodes, testing under a high-electrical-strength liquid was necessary. The avalanche breakdown voltage was 1000 V representing the highest reverse breakdown voltage to be reported for any CVD-grown SiC diode.

Matus, L. G.↗

Processing and properties of SiC whisker- and particulate-reinforced reaction bonded Si3N4

The microstructure and mechanical properties of reaction bonded Si3N4 (RBSN) reinforced with SiC whiskers of particles were investigated using RBSN composites made from colloidally pressed octanol dispersions of high-purity Si powders mixed with either SiC whiskers or alpha-SiC particles. Results of investigations, revealing high conversions of Si to Si3N4, specific surface areas, and constant relative densities and strengths, showed that the uniform microstructure and small flaw size of the matrix were maintained in the composites and that no degradation of the reinforcements was taking place. Neither the monolithic nor the composite materials exhibited R-curve behavior. A modest increase in fracture toughness was observed only in the RBSN containing 33 vol pct SiC(p).

Lightfoot, A.↗

s-process Ba, Nd, and Sm in presolar SiC from the Murchison meteorite

Ion microprobe isotopic measurements of Ba, Nd, and Sm in the K-series SiC size separates on which noble gas measurements were made by Lewis et al. (1990) are reported. All elements show isotopic abundance patterns characteristic for the s-process. The Ba-134/Ba-136 ratios are distinct from solar, indicating that s-Ba in SiC is different from that in the solar system. Ba-138/Ba-136 ratios decrease with grain size; if interpreted as being due to different neutron exposures, this trend is opposite of that shown by the Kr-86/Kr-82 ratios. Although other isotropic ratios for Ba and those for Nd and Sm differ in detail from theoretical predictions, the disagreements probably being due to uncertainties in the n-capture cross sections and simplifications in the models, the general agreement of the data with models of s-process nucleosynthesis support an AGB star origin for the relatively fine-grain SiC under consideration. Ba-136 in SiC is up to 85 percent pure s-process.

Zinner, Ernst↗

SiC device development for high temperature sensor applications

Progress made in the processing and characterization of 3C-SiC for high temperature sensor applications is reviewed. Piezoresistance properties of silicon carbide and the temperature coefficient of resistivity of n-type beta-SiC are presented. In addition, photoelectrical etching and dopant selective etch-stops in SiC and high temperature Ohmic contacts for n-type beta-SiC sensors are discussed.

Shor, J. S.↗

Presolar SiC in chondrites - How variable and how many sources?

The carbon and silicon isotropic compositions of 246 isotopically anomalous SiC grains measured in low concentration residues are reported. The residues were prepared from nine chondrites, namely, 6 unequilibrated ordinary chondrites (UOCs), Qingzhen (EH3), Leoville (CV3), and Murchison (CM2). Murchison is used as a standard to which all the other meteorites studied are compared. The range of isotopic compositions exhibited by UOC SiC is found to be similar to Murchison, except in Inman. Inman SiC has a distinctly different distribution of its silicon isotopic composition compared to the other meteorites. Residues from Qingzhen and Leoville produce only one anomalous SiC grain each.

Alexander, C. M. O'D.↗

Microstructural and strength stability of a developmental CVD SiC fiber

The effects of thermal exposure on the room temperature tensile strength and microstructure of a developmental 50 micron CVD SiC fiber have been studied. The fibers were heat treated between 600 and 2000 C in 0.1 MPa argon and air environments for up to 100 hr. In the as-fabricated condition, the fibers showed approximately 6 GPa tensile strength. After argon treatment, the fibers showed strength degradation after 1 hr exposure beyond 1000 C, but those exposed between 1600 and 2000 C retained approximately 2 GPa strength. TEM results showed microstructural changes both in the surface coating and SiC sheath. Flaws created by the rearrangement of carbon in the surface coating and growth of equiaxed SiC grain zone in the SiC sheath are the suggested mechanisms of strength degradation. After air treatment, fibers showed strength degradation after only 2 min exposure at 600 C. Strength retention after 2 min at 1500 C was approximately 2 GPa. Oxidation of the surface coating is the primary reason for strength degradation.

Bhatt, Ramakrishna T.↗