Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STANDING WAVES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Scanning Tunneling Microscopy Observation of Phonon Condensate

Using quantum tunneling of electrons into vibrating surface atoms, phonon oscillations can be observed on the atomic scale. Phonon interference patterns with unusually large signal amplitudes have been revealed by scanning tunneling microscopy in intercalated van der Waals heterostructures. Our results show that the effective radius of these phonon quasi-bound states, the real-space distribution of phonon standing wave amplitudes, the scattering phase shifts, and the nonlinear intermode coupling strongly depend on the presence of defect-induced scattering resonance. The observed coherence of these quasi-bound states most likely arises from phase- and frequency-synchronized dynamics of all phonon modes, and indicates the formation of many-body condensate of optical phonons around resonant defects. We found that increasing the strength of the scattering resonance causes the increase of the condensate droplet radius without affecting the condensate fraction inside it. The condensate can be observed at room temperature.

36 MATERIALS SCIENCE↗

Redox-driven atomic-scale changes in mixed catalysts: VO X / WO X / α-TiO 2 (110)

X-ray studies of vanadium–tungsten mixed-monolayer-oxide catalysts grown on the rutile α-TiO 2 (110) single crystal surface show redox behavior not observed for lone supported vanadium or tungsten oxides. Two cases are presented: sub-monolayer (sub-ML) vanadium oxide (vanadia) grown on ML tungsten oxide and ML vanadia grown on sub-ML tungsten oxide. The X-ray standing wave (XSW) and X-ray photoelectron spectroscopy (XPS) observations for both cases show coverage-dependent reversible redox-induced atomic-scale structural and chemical state changes. Atomic force microscopy shows that the mixed VO X /WO X overlayers have a conformal film-like structure in the as-deposited state. XSW analysis in light of XPS reveals that the V and W cations that are uncorrelated with the substrate lattice play an important role in catalytic redox reactions. Distinct differences in the redox-induced changes for these two mixed catalysts result from tuning the ratio of V to W, and relationships are drawn between the catalyst composition, structure, and chemistry. In this work, comparison of these V–W mixed cases and the corresponding unmixed cases reveals a synergistic effect in which the reduction of W can be significantly enhanced by the addition of V.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Direct quantitative identification of the “surface trans-effect”

The strong parallels between coordination chemistry and adsorption on metal surfaces, with molecules and ligands forming local bonds to individual atoms within a metal surface, have been established over many years of study. The recently proposed “surface trans-effect” (STE) appears to be a further manifestation of this analogous behaviour, but so far the true nature of the modified molecule–metal surface bonding has been unclear. The STE could play an important role in determining the reactivities of surface-supported metal–organic complexes, influencing the design of systems for future applications. However, the current understanding of this effect is incomplete and lacks reliable structural parameters with which to benchmark theoretical calculations. Using X-ray standing waves, we demonstrate that ligation of ammonia and water to iron phthalocyanine (FePc) on Ag(111) increases the adsorption height of the central Fe atom; dispersion corrected density functional theory calculations accurately model this structural effect. The calculated charge redistribution in the FePc/H 2 O electronic structure induced by adsorption shows an accumulation of charge along the σ-bonding direction between the surface, the Fe atom and the water molecule, similar to the redistribution caused by ammonia. Finally, this apparent σ-donor nature of the observed STE on Ag(111) is shown to involve bonding to the delocalised metal surface electrons rather than local bonding to one or more surface atoms, thus indicating that this is a true surface trans-effect.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Near-canopy horizontal concentration heterogeneity of semivolatile oxygenated organic compounds and implications for 2-methyltetrols primary emissions

Semivolatile oxygenated organic compounds (SV-OVOCs) are important atmospheric species, in particular for the production and chemistry of atmospheric particulate matter and related impacts on air quality and climate. In this study, SV-OVOCs were collected in the horizontal plane of the roughness layer over the tropical forest in the central Amazon during the wet season of 2018. A sampler mounted to a copter-type, hovering unmanned aerial vehicle was used. Underlying the collection region, a plateau forest transitioned into a slope forest across several hundred meters. The concentrations of pinonic and pinic acids, which are monoterpene oxidation products, had no statistical difference over the two forests. By comparison, across the study period, differences in the concentration of 2-methyltetrols, which are products of isoprene oxidation, ranged from -70% to +480% over the two forests. The chemical lifetime of 2-methyltetrols in the atmosphere is sufficiently long that heterogeneity in the isoprene emission rate from the two forests followed by atmospheric oxidation does not explain the concentration heterogeneity of 2-methyltetrols. Standing waves and local meteorology also cannot account for the heterogeneity. Of the possibilities considered, the most plausible explanation is the direct emission from the forest of 2-methyltetrols produced through biological processes within the plants. Under this explanation, the rate of direct SV-OVOC emissions should be modulated by forest type and related environmental stressors. Direct emissions of SV-OVOCs should be more broadly considered for constraining and improving models of atmospheric composition, transport, and chemistry over tropical forests.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

BeyondPlanck X. Bandpass and beam leakage corrections

We discuss the treatment of bandpass and beam leakage corrections in the Bayesian BeyondPlanck CMB analysis pipeline as applied to the Planck LFI measurements. As a preparatory step, we first apply three corrections to the nominal LFI bandpass profiles including removal of a known systematic effect in the ground measuring equipment at 61 GHz; smoothing of standing wave ripples; and edge regularization. The main net impact of these modifications is an overall shift in the 70 GHz bandpass of +0.6 GHz; we argue that any analysis of LFI data products, either from Planck or BeyondPlanck, should use these new bandpasses. In addition, we fit a single free bandpass parameter for each radiometer of the form Δ i = Δ 0 + $δ$ i , where Δ 0 represents an absolute frequency shift per frequency band and $δ$i is a relative shift per detector. The absolute correction is only fitted at 30 GHz with a full $\chi$ 2 -based likelihood, resulting in a correction of Δ 30 = 0.24 ± 0.03 GHz. The relative corrections are fitted using a spurious map approach, fundamentally similar to the method pioneered by the WMAP team, but without introducing many additional degrees of freedom. All bandpass parameters are sampled using a standard Metropolis sampler within the main BeyondPlanck Gibbs chain, and bandpass uncertainties are thus propagated to all other data products in the analysis. In total, we find that our bandpass model significantly reduces leakage effects. For beam leakage corrections, we adopt the official Planck LFI beam estimates without additional degrees of freedom, and only marginalize over the underlying sky model. We note that this is the first-time leakage from beam mismatch has been included for Planck LFI maps.

79 ASTRONOMY AND ASTROPHYSICS↗

Comparison of electrostatic and electromagnetic simulations for very high frequency plasmas

A two-dimensional self-consistent fluid model combined with the full set of Maxwell equations is developed to investigate an argon capacitively coupled plasma, focusing on the electromagnetic effects on the discharge characteristics at various discharge conditions. The results indicate that there exist distinct differences in plasma characteristics calculated with the so-called electrostatic model (i.e., without taking into account the electromagnetic effects) and the electromagnetic model (which includes the electromagnetic effects), especially at very high frequencies. Indeed, when the excitation source is in the high frequency regime and the electromagnetic effects are taken into account, the plasma density increases significantly and meanwhile the ionization rate evolves to a very different distribution when the electromagnetic effects are dominant. Furthermore, the dependence of the plasma characteristics on the voltage and pressure is also investigated, at constant frequency. It is observed that when the voltage is low, the difference between these two models becomes more obvious than at higher voltages. As the pressure increases, the plasma density profiles obtained from the electromagnetic model smoothly shift from edge-peaked over uniform to a broad maximum in the center. In addition, the edge effect becomes less pronounced with increasing frequency and pressure, and the skin effect rather than the standing-wave effect becomes dominant when the voltage is high.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Revisiting the adsorption of copper-phthalocyanine on Au(111) including van der Waals corrections

We have studied the adsorption of copper-phthalocyanine on Au(111) by means of van der Waals corrected density functional theory using the Tkatchenko-Scheffler method. We have compared the element and site resolved adsorption distances to recent experimental normal-incident X-ray standing wave measurements. The measured adsorption distances could be reproduced within a deviation of 1% for the Cu atom, 1% for the C atoms, and 2% for the N atoms. The molecule was found to have a magnetic moment of 1 μ{sub B} distributed over the Cu and the N atoms of the pyrrole ring. Simulated scanning tunnel microscopy images based on the total and on the spin-resolved differential charge densities are provided for bias voltages of −1.45 and 1.45 eV.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Photonic confinement in laterally structured metal-organic microcavities

We investigate the formation of optical modes in organic microcavities with an incorporated perforated silver layer. The metal leads to a formation of Tamm-plasmon-polaritons and thus separates the sample into metal-free or metal-containing areas, supporting different resonances. This mode splitting is exploited to confine photons in elliptic holes and triangular cuts, forming distinctive standing wave patterns showing the strong lateral confinement. A comparison with a Maxwell-Bloch based rate equation model clearly shows the nonlinear transition into the lasing regime. The concentration of the electric field density and inhibition of lateral loss channels in turn decreases the lasing threshold by up to one order of magnitude, to 0.1 nJ. By spectroscopic investigation of such a triangular wedge, we observe the transition from the unperturbed cavity state to a strongly confined complex transversal mode. Such a structured silver layer can be utilized in future for charge carrier injection in an electrically driven organic solid state laser.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Dielectric resonator method for determining gap symmetry of superconductors through anisotropic nonlinear Meissner effect

We present a new measurement method which can be used to image the gap nodal structure of superconductors whose pairing symmetry is under debate. This technique utilizes a high quality factor microwave resonance involving the sample of interest. While supporting a circularly symmetric standing wave current pattern, the sample is perturbed by a scanned laser beam, creating a photoresponse that was previously shown to reveal the superconducting gap anisotropy. Simulation and the measurement of the photoresponse of an unpatterned Nb film show less than 8% anisotropy, as expected for a superconductor with a nearly isotropic energy gap along with expected systematic uncertainty. On the other hand, measurement of a YBa 2 Cu 3 O 7- δ thin film shows a clear 4-fold symmetric image with ~12.5% anisotropy, indicating the well-known 4-fold symmetric d x 2 - y 2 gap nodal structure in the ab -plane. The deduced gap nodal structure can be further cross-checked by low temperature surface impedance data, which are simultaneously measured. The important advantage of the presented method over the previous spiral resonator method is that it does not require a complicated lithographic patterning process which limits one from testing various kinds of materials due to photoresponse arising from patterning defects. This advantage of the presented technique, and the ability to measure unpatterned samples such as planar thin films and single crystals, enables one to survey the pairing symmetry of a wide variety of unconventional superconductors.

47 OTHER INSTRUMENTATION↗

High-power test of a C-band linear accelerating structure with an RFSoC-based LLRF system

Normal conducting linear particle accelerators consist of multiple rf stations with accelerating structure cavities. Low-level rf (LLRF) systems are employed to set the phase and amplitude of the field in the accelerating structure and to compensate for the pulse-to-pulse fluctuation of the rf field in the accelerating structures with a feedback loop. The LLRF systems are typically implemented with analog rf mixers, heterodyne-based architectures, and discrete data converters. There are multiple rf signals from each of the rf stations, so the number of rf channels required increases rapidly with multiple rf stations. With a large number of rf channels, the footprint, component cost, and system complexity of the LLRF hardware will increase significantly. To meet the design goals of being compact and affordable for future accelerators, we have designed the next-generation LLRF (NG-LLRF) with a higher integration level based on RFSoC technology. The NG-LLRF system samples rf signals directly and performs rf mixing digitally. Further, the NG-LLRF has been characterized in loopback mode to evaluate the performance of the system and has also been tested with a standing-wave accelerating structure, a prototype for the Cool Copper Collider (C 3 ) with a peak rf power level up to 16.45 MW. The loopback test demonstrated amplitude fluctuation below 0.15% and phase fluctuation below 0.15°, which are considerably better than the requirements of C 3 . The rf signals from the different stages of the accelerating structure at different power levels are measured by the NG-LLRF, which will be critical references for the control algorithm designs. The NG-LLRF also offers flexibility in waveform modulation, so we have used rf pulses with various modulation schemes, which could be useful for controlling some of the rf stations in accelerators. In this paper, the high-power test results at different stages of the test setup will be summarized, analyzed, and discussed.

47 OTHER INSTRUMENTATION↗

Spatially-periodic microplasmas in complex microchannel networks: wall-plasma interactions and dynamic behavior

Wall-plasma interactions have been observed for spatially-periodic microplasmas generated in 300–700 µm wide channels fabricated in nanoporous alumina. Examination of Ne microplasma discs produced in a standing-wave pattern in Al 2 O 3 channels illustrates the competition between electron production at the sheath-wall interface and loss by recombination in an atmospheric pressure background. Two topologies of the microplasma arrays are observed. For channel widths (d) less than 450 µm, the microplasmas are generally centered in the channel and sustained by electron generation at both plasma sheath/channel wall interfaces, presumably including the release of charge residing in the hexagonal alumina pores. As d is progressively increased from 300 to 450 µm, the microchannel plasma cross-section is gradually transformed from circular to elliptical, and its surface area declines by as much as 50% so as to minimize e - losses to the background gas. Increasing d above ~450 µm abruptly switches the topology to one in which plasmas having a triangular cross-section attach to one of the channel walls in a pattern that alternates along the channel axis. Microfabricating trapezoidal cross-section channels into complex geometries, including the Cornu spiral and intersecting linear arrays, also reveals dynamic behavior in the propagation of microplasmas. For a common spiral structure, observations of plasma expansion show the wavefront propagates over the corrugated surface or within the channel with radial and azimuthal velocities of 3 ± 1 km s -1 and 8 ± 1.5 km s -1 , respectively. Plasma formation is initiated in each ring of the spiral through electron seeding by streamers propagating radially outward at velocities approaching 200 km s -1 . In addition to electrostatic charge-mediated variations in the mean separation between adjacent microplasmas, the time-dependent interference between two 1D microplasma arrays has been observed during plasma expansion. Reproducible ignition of a microplasma ensemble along ridges micromachined into channels near the intersections of two linear arrays has also been realized. The results reported here demonstrate that microchannels with the walls overcoated with any of a variety of materials provide a promising platform for examining in detail the interaction of low temperature plasma with a surface of arbitrary composition and topography.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experimental determination of axion signal power of dish antennas and dielectric haloscopes using the reciprocity approach

The reciprocity approach is a powerful method to determine the expected signal power of axion haloscopes in a model-independent way. Especially for open and broadband setups like the MADMAX dielectric haloscope the sensitivity to the axion field is difficult to calibrate since they do not allow discrete eigenmode analysis and are optically too large to fully simulate. The central idea of the reciprocity approach is to measure a reflection-induced test field in the setup instead of trying to simulate the axion-induced field. In this article, the reciprocity approach is used to determine the expected signal power of a dish antenna and a minimal dielectric haloscope directly from measurements. The results match expectations from simulation but also include important systematic effects that are too difficult to simulate. In particular, the effect of antenna standing waves and higher order mode perturbations can be quantified for the first time in a dielectric haloscope.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

The Electromagnetic Characteristics of the Tianlai Cylindrical Pathfinder Array

A great challenge for 21 cm intensity mapping experiments is the strong foreground radiation which is orders of magnitude brighter than the 21 cm signal. Removal of the foreground takes advantage of the fact that its frequency spectrum is smooth while the redshifted 21 cm signal spectrum is stochastic. However, a complication is the non-smoothness of the instrument response. This paper describes the electromagnetic simulation of the Tianlai cylinder array, a pathfinder for 21 cm intensity mapping experiments. Due to the vast scales involved, a direct simulation requires a large amount of computing resources. We have made the simulation practical by using a combination of methods: first simulate a single feed, then an array of feed units, finally with the feed array and a cylindrical reflector together, obtain the response for a single cylinder. We studied its radiation pattern, bandpass response and the effects of mutual coupling between feed units, and compared the results with observation. Many features seen in the measurement result are reproduced well in the simulation, especially the oscillatory features which are associated with the standing waves on the reflector. The mutual coupling between feed units is quantified with S-parameters, which decrease as the distance between the two feeds increases. Based on the simulated S-parameters, we estimate the correlated noise which has been seen in the visibility data, and the results show very good agreement with the data in both magnitude and frequency structures. These results provide useful insights on the problem of 21 cm signal extraction for real instruments.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Beta-induced Alfvén eigenmodes destabilized by resonant magnetic perturbations in the J-TEXT tokamak

Investigations of beta-induced Alfvén eigenmodes (BAEs) destabilized by resonant magnetic perturbations (RMPs) have been conducted on the J-TEXT tokamak. In the Ohmic discharges, with RMPs having finite perturbed amplitudes, two different types of Alfvén eigenmodes have been observed and identified. One is considered as m-BAE, due to the strong correlation with magnetic island in some noticeable aspects, for example, frequency characteristic, mode number and driving mechanism. Specifically, the standing wave nodes of m-BAE are located at the O point and X point of the magnetic island. Another one is discerned as the magnetic island-induced AE (labeled as the MIAE-like mode in this work), which is consistent with the prediction of theory (Biancalani et al 2010 Phys. Rev. Lett. 105 095002). The frequency of MIAE-like mode is found to be approximately proportional to the square of magnetic island width.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Innovative compact braze-free accelerating cavity

We report that high energy physics experiments using particle accelerators as well as industrial and medical applications are continuously seeking more compact, robust and cheaper accelerating structures. As of today, stable operating gradients, exceeding 100 MV/m, have been demonstrated by the SLAC group in the X-Band (11.424 GHz). These experiments show that hard structures, fabricated without high-temperature processes, achieve a better high gradient performance in terms of accelerating gradients. Therefore, we present an innovative and compact type of accelerating cavity that avoids any high-temperature processes like brazing or diffusion bonding. All cells are joined together by means of specifically designed and proprietary screws which ensure good vacuum and RF contacts. Two three-cell standing-wave accelerating structures, designed to operate in the pi-mode at 11.424 GHz, have been successfully built and cold tested. In order to guarantee a vacuum envelope and mechanically robust assembly, we used the Electron Beam Welding (EBW) and the Tungsten Inert Gas (TIG) processes. Lastly, this work has been carried out in the framework of a funded project by the Vth Committee of the INFN for the Laboratori Nazionali di Frascati (LNF), within a large international collaboration between LNF, SLAC and KEK for the development of X-Band accelerating cavities using "hard structure" technology.

43 PARTICLE ACCELERATORS↗

Comparative analysis of plasmon modes in layered Lindhard metals and strange metals

The enigmatic strange metal remains one of the central unsolved problems of 21st century science. Understanding this phase of matter requires knowledge of the momentum- and energy-resolved dynamic charge susceptibility 𝜒⁡(𝑞,𝜔), especially at finite momentum. Inelastic electron scattering (EELS), performed in either transmission or reflection geometry, is a powerful probe of 𝜒⁡(𝑞,𝜔). For the prototypical strange metal Bi 2 ⁢Sr 2 ⁢CaCu 2 ⁢O 8+𝑥 , transmission- and reflection EELS, and infrared (IR) spectroscopy agree at 𝑞∼0, all revealing a highly damped plasmon near 1 eV. At larger 𝑞, however, EELS results show unresolved discrepancies. Since IR data are highly reproducible, it is advantageous to use IR data to calculate what the expected EELS response should be at modest 𝑞. Building on prior momentum-resolved reflection geometry M-EELS work [Chen et al., Phys. Rev. B 109, 045108 (2024)], we extend this approach to transmission EELS for finite stacks of metallic layers, comparing a “textbook” Lindhard metal to a strange metal. In the Lindhard case, the low-𝑞 response is dominated by long-lived, standing wave plasmon modes arising from interlayer Coulomb coupling, with in-plane dispersions that resemble the well-known Fetter modes of layered metals. This behavior depends only on the geometry and the long-range nature of the Coulomb interaction and is largely insensitive to layer details. At larger 𝑞, the response reflects the microscopic properties of individual layers. For the strange metal, calculations based on IR data predict a highly damped plasmon with weak dispersion and no distinct surface mode. While our results match IR and M-EELS at low 𝑞, they do not reproduce any published EELS spectra at large 𝑞, highlighting unresolved discrepancies that demand further experimental investigation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

High-precision phase control of an optical lattice with up to 50 dB noise suppression

An optical lattice is a periodic light crystal constructed from the standing-wave interference patterns of laser beams. It can be used to store and manipulate quantum degenerate atoms and is an ideal platform for the quantum simulation of many-body physics. A principal feature is that optical lattices are flexible and possess a variety of multidimensional geometries with modifiable band structure. An even richer landscape emerges when control functions can be applied to the lattice by modulation of the position or amplitude with Floquet driving. However, the desire of realizing high-modulation bandwidths while preserving extreme lattice stability has been difficult to achieve. In this paper, we demonstrate an effective solution that consists of overlapping two counterpropagating lattice beams and controlling the phase and intensity of each with independent acousto-optic modulators. Our phase controller mixes sampled light from both lattice beams with a common optical reference. This dual heterodyne locking method allows exquisite determination of the lattice position, while also removing parasitic phase noise accrued as the beams travel along separate paths. Here, we report up to 50 dB suppression in lattice phase noise in the 0.1–1 Hz band, along with significant suppression spanning more than 4 decades of frequency. The absolute phase diffusion of the lattice position is only 10 Å when integrated over 10 s. This method permits precise, high-bandwidth modulation (greater than 50 kHz) of the optical lattice intensity and phase. We demonstrate the efficacy of this approach by executing intricate time-varying phase profiles for atom interferometry.

Atom interferometry↗

Nanoscale stratification of optical excitation in self-interacting one-dimensional arrays

The major assumption of the Lorentz-Lorenz theory about uniformity of local fields and atomic polarization in dense material does not hold in finite groups of atoms, as we reported earlier [A. E. Kaplan and S. N. Volkov, Phys. Rev. Lett. 101, 133902 (2008)]. The uniformity is broken at subwavelength scale, where the system may exhibit strong stratification of local field and dipole polarization, with the strata period being much shorter than the incident wavelength. In this paper, we further develop and advance that theory for the most fundamental case of one-dimensional arrays, and study nanoscale excitation of so-called 'locsitons' (local field excitations) and their standing waves (strata) that result in size-related resonances and related large field enhancement in finite arrays of atoms. The locsitons may have a whole spectrum of spatial frequencies, ranging from long waves, to an extent reminiscent of ferromagnetic domains, to supershort waves, with neighboring atoms alternating their polarizations, which are reminiscent of antiferromagnetic spin patterns. Of great interest is the different kind of 'hybrid' mode of excitation, greatly departing from any magnetic analogies. We also study differences between Ising-type near-neighbor approximation and the case where each atom interacts with all other atoms in the array. We find an infinite number of 'exponential eigenmodes' in the lossless system in the latter case. At certain 'magic' numbers of atoms in the array, the system may exhibit self-induced (but linear in the field) cancellation of resonant local-field suppression. We also studied nonlinear modes of locsitons and found optical bistability and hysteresis in an infinite array for the simplest modes.

74 ATOMIC AND MOLECULAR PHYSICS↗