Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Surface instability of binary compounds caused by sputter yield amplification

It is demonstrated that the flat surface of a binary material that is subjected to normal-incidence ion bombardment can be unstable even if the curvature dependence of the sputter yields is negligibly small. This unforeseen instability is brought about by sputter yield amplification, and it results in the formation of a disordered array of nanodots with the lighter of the two atomic species concentrated at the peaks of the dots.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Enhanced electrical and noise properties of nanocomposite vanadium oxide thin films by reactive pulsed-dc magnetron sputtering

Thin films of VO{sub x} (1.3 {<=} x {<=} 2) were deposited by reactive pulsed-dc magnetron sputtering of a vanadium metal target while RF-biasing the substrate. Rutherford back scattering, glancing angle x-ray, and cross-sectional transmission electron microscopy measurements revealed the formation of nanocolumns with nanotwins within VO{sub x} samples. The resistivity of nanotwinned VO{sub x} films ranged from 4 m{Omega}{center_dot}cm to 0.6 {Omega}{center_dot}cm and corresponding temperature coefficient of resistance between -0.1% and -2.6% per K, respectively. The 1/f electrical noise was analyzed in these VO{sub x} samples using the Hooge-Vandamme relation. These VO{sub x} films are comparable or surpass commercial VO{sub x} films deposited by ion beam sputtering.

36 MATERIALS SCIENCE↗

Magnetron sputtering system for fabrication of X-ray multilayer optics

A specially designed DC/RF magnetron sputtering system has been installed for the development of large area x-ray multilayer (ML) optics at Indus synchrotron radiation facility. A brief description of the system configuration, automation and operating conditions are presented. The system has the capability of fabricating large area (300 Multiplication-Sign 100-mm{sup 2}) X-ray MLs with required accuracy, uniformity and reproducibility. Thin film growth suitable for fabrication of X-ray ML optics has achieved by optimizing the sputtering process parameters. The representative results are presented.

36 MATERIALS SCIENCE↗

Properties of nano structured Ag-TiO{sub 2} composite coating on stainless steel using RF sputtering method

RF Sputtering system is one of the Physical Vapour Deposition (PVD) methods that have been widely used to produce hard coating. This technique is used to deposit thin layers of metallic substrates such as stainless steel (SS). From this process, a good adhesiveness and wear resistance coating can be produced for biomedical applications. In this study, RF sputtering method was used to deposit TiO{sub 2}-Ag composite coatings via various deposition parameters. The parameters are RF power of 350W, gas composition (Ar: O{sub 2}) 50:5 and deposition time at 1, 2, 4 and 6 hours. Scanning Electron Microscopy (SEM), X-Ray Diffraction (XRD) and Raman spectroscopy were used to characterize surface area of coated samples. The formation of nanocrystalline thin film and the surface morphology were examined using SEM. The crystallite size of TiO{sub 2}-Ag composite coatings were estimated between 20-60 nm based on XRD analysis using Scherer equation and SEM evaluation. The Raman and XRD results suggested that the structure of the TiO{sub 2}-Ag consist of anatase and rutile phases. It also showed that the intensity of anatase peaks increased after samples undergone annealing process at 500 Degree-Sign C.

36 MATERIALS SCIENCE↗

Microstructural evolution of thin film vanadium oxide prepared by pulsed-direct current magnetron sputtering

Vanadium oxide (VO{sub x}) thin films have been deposited by pulsed-DC magnetron sputtering using a metallic vanadium target in a reactive argon and oxygen environment. While the process parameters (power, total pressure, oxygen-to-argon ratio) remained constant, the deposition time was varied to produce films between 75 {+-} 6 and 2901 {+-} 30 A thick, which were then optically and electrically characterized. The complex dielectric function spectra ({epsilon} = {epsilon}{sub 1} + i{epsilon}{sub 2}) of the films from 0.75 to 5.15 eV were extracted by ex situ, multiple-angle spectroscopic ellipsometry (SE) measurements for the series of varied thickness VO{sub x} samples. Significant changes in {epsilon} and resistivity occur as a function of thickness, indicating the correlations exist between the electrical and the optical properties over this spectral range. In addition, in situ measurements via real time SE (RTSE) were made on the film grown to the largest thickness to track optical property and structural variations during growth. RTSE was also used to characterize changes in the film occurring after growth was completed, namely during post sputtering in the presence of argon and oxygen while the sample is shielded, and atmospheric exposure. RTSE indicates that the exposure of the film to the argon and oxygen environment, regardless of the shutter isolating the target, causes up to 200 A of the top surface of the deposited film to become more electrically resistive as evidenced by variations in {epsilon}. Exposure of the VO{sub x} thin film to atmospheric conditions introduces a similar change in {epsilon}, but this change occurs throughout the bulk of the film. A combination of these observations with RTSE results indicates that thinner, less ordered VO{sub x} films are more susceptible to drastic changes due to atmospheric exposure and that microstructural variations in this material ultimately control its environmental stability.

36 MATERIALS SCIENCE↗

Boron-rich plasma by high power impulse magnetron sputtering of lanthanum hexaboride

Boron-rich plasmas have been obtained using a LaB{sub 6} target in a high power impulse sputtering (HiPIMS) system. The presence of {sup 10}B{sup +}, {sup 11}B{sup +}, Ar{sup 2+}, Ar{sup +}, La{sup 2+}, and La{sup +} and traces of La{sup 3+}, {sup 12}C{sup +}, {sup 14}N{sup +}, and {sup 16}O{sup +} have been detected using an integrated mass and energy spectrometer. Peak currents as low as 20 A were sufficient to obtain plasma dominated by {sup 11}B{sup +} from a 5 cm planar magnetron. The ion energy distribution function for boron exhibits an energetic tail extending over several 10 eV, while argon shows a pronounced peak at low energy (some eV). This is in agreement with models that consider sputtering (B, La) and gas supply (from background and 'recycling'). Strong voltage oscillations develop at high current, greatly affecting power dissipation and plasma properties.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Intermixing of InGaAs/GaAs quantum wells and quantum dots using sputter-deposited silicon oxynitride capping layers

Various approaches can be used to selectively control the amount of intermixing in III-V quantum well and quantum dot structures. Impurity-free vacancy disordering is one technique that is favored for its simplicity, however this mechanism is sensitive to many experimental parameters. In this study, a series of silicon oxynitride capping layers have been used in the intermixing of InGaAs/GaAs quantum well and quantum dot structures. These thin films were deposited by sputter deposition in order to minimize the incorporation of hydrogen, which has been reported to influence impurity-free vacancy disordering. The degree of intermixing was probed by photoluminescence spectroscopy and this is discussed with respect to the properties of the SiO{sub x}N{sub y} films. This work was also designed to monitor any additional intermixing that might be attributed to the sputtering process. In addition, the high-temperature stress is known to affect the group-III vacancy concentration, which is central to the intermixing process. This stress was directly measured and the experimental values are compared with an elastic-deformation model.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Very low 1/f barrier noise in sputtered MgO magnetic tunnel junctions with high tunneling magnetoresistance

Low frequency 1/f barrier noise has been investigated in sputtered MgO magnetic tunnel junctions (MTJs) with a tunneling magnetoresistance ratio of up to 330% at room temperature. The lowest normalized noise parameter {alpha} of the tunnel barrier reaches 2.5 Multiplication-Sign 10{sup -12}-2.1 Multiplication-Sign 10{sup -11} {mu}m{sup 2}, which is comparable to that found in MTJs with the MgO barrier grown by MBE or electron-beam evaporation. This normalized barrier noise is almost bias independent in the voltage range of up to {+-}1.2 V. The low noise level and high voltage stability may reflect the high quality of the sputtered MgO with a uniform distribution of defects in the MgO layer.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Non-conducting interfaces of LaAlO{sub 3}/SrTiO{sub 3} produced in sputter deposition: The role of stoichiometry

We have investigated the properties of interfaces between LaAlO{sub 3} films grown on SrTiO{sub 3} substrates singly terminated by TiO{sub 2}. We used RF sputtering in a high-pressure oxygen atmosphere. The films are smooth, with flat surfaces. Transmission electron microscopy shows sharp and continuous interfaces with some slight intermixing. The elemental ratio of La to Al, measured by the energy dispersive X-ray technique, is found to be 1.07. Importantly, we find these interfaces to be non-conducting, indicating that the sputtered interface is not electronically reconstructed in the way reported for films grown by pulsed laser deposition because of the different interplays among stoichiometry, mixing, and oxygen vacancies.

36 MATERIALS SCIENCE↗

Heteroepitaxial Ge-on-Si by DC magnetron sputtering

The growth of Ge on Si(100) by DC Magnetron Sputtering at various temperatures is studied by Spectroscopic Ellipsometry and Transmission Electron Microscopy. Smooth heteroepitaxial Ge films are prepared at relatively low temperatures of 380°C. Typical Stransky-Krastanov growth is observed at 410°C. At lower temperatures (320°C), films are essentially amorphous with isolated nanocrystallites at the Si-Ge interface. A minor oxygen contamination at the interface, developing after ex-situ oxide removal, is not seen to hinder epitaxy. Compensation of dislocation-induced acceptors in Ge by sputtering from n-doped targets is proposed.

36 MATERIALS SCIENCE↗

Multi-jump magnetic switching in ion-beam sputtered amorphous Co{sub 20}Fe{sub 60}B{sub 20} thin films

Unconventional multi-jump magnetization reversal and significant in-plane uniaxial magnetic anisotropy (UMA) in the ion-beam sputtered amorphous Co{sub 20}Fe{sub 60}B{sub 20}(5–75 nm) thin films grown on Si/amorphous SiO{sub 2} are reported. While such multi-jump behavior is observed in CoFeB(10 nm) film when the magnetic field is applied at 10°–20° away from the easy-axis, the same is observed in CoFeB(12.5 nm) film when the magnetic field is 45°–55° away from easy-axis. Unlike the previous reports of multi-jump switching in epitaxial films, their observance in the present case of amorphous CoFeB is remarkable. This multi-jump switching is found to disappear when the films are crystallized by annealing at 420 °C. The deposition geometry and the energy of the sputtered species appear to intrinsically induce a kind of bond orientation anisotropy in the films, which leads to the UMA in the as-grown amorphous CoFeB films. Exploitation of such multi-jump switching in amorphous CoFeB thin films could be of technological significance because of their applications in spintronic devices.

36 MATERIALS SCIENCE↗

Overcoming challenges to the formation of high-quality polycrystalline TiO{sub 2}:Ta transparent conducting films by magnetron sputtering

The work is focused on understanding the physical processes responsible for the modification of the structure, electrical and optical properties of polycrystalline TiO{sub 2}:Ta films formed by annealing of initially amorphous films grown by direct current magnetron sputtering of electrically conductive ceramic targets. It is shown that fine tuning of the oxygen content during deposition of amorphous TiO{sub 2}:Ta films is critical to achieving low resistivity and high optical transmittance after annealing. Increasing the total pressure during magnetron sputter deposition is shown to decrease the sensitivity of the annealed films to the oxygen flow variation during deposition of the initially amorphous layers. Polycrystalline anatase TiO{sub 2}:Ta films of low electrical resistivity (ρ{sub H} = 1.5 × 10{sup −3}Ω cm), high free electron mobility (μ{sub H} = 8 cm{sup 2}/Vs), and low extinction (k{sub 550nm} = 0.006) are obtained in this way at a total pressure of 2 Pa. The dependence of the polycrystalline film electrical properties on the oxygen content is discussed in terms of Ta dopant electrical activation/deactivation taking into account the formation of compensating defects at different oxygen pressures. The temperature-dependent transport of the polycrystalline anatase TiO{sub 2}:Ta films is investigated showing the dominant role of the optical phonon scattering in the case of films with an optimum Ti/O ratio.

36 MATERIALS SCIENCE↗

Adhesion strength of sputtered TiAlN-coated WC insert tool

The adhesion strength of TiAlN coating that deposited by using DC magnetron sputtering on WC insert tool are studied. TiAlN coating are deposited on Tungsten Carbide (WC) insert tool by varying negatively substrate bias from 79 to 221 volt and nitrogen flow rate from 30 to 72 sccm. The adhesion strength are obtained by using Rockwell indentation test method with a Brale diamond at applied load of 60,100 and 150 kgf. The lateral diameter of indentation is plotted on three different applied loads and the adhesion strength of TiAlN coating was obtained from the curved slopes at 100 and 150 kgf. The lower curve slop indicated better adhesion strength. The results shows that the adhesion strength of sputterred TiAlN coating tend to increase as the negatively substrate bias and nitrogen flow rate are increased.

36 MATERIALS SCIENCE↗

Carbon film deposition on SnO{sub 2}/Si(111) using DC unbalanced magnetron sputtering

In this paper, carbon deposition on SnO{sub 2} layer using DC unbalanced magnetron-sputtering technique at low temperature has been systematically studied. Sputtering process were carried out at pressure of 4.6×10{sup −2} Torr by keeping the substrate temperature at 300 °C. SnO{sub 2} were growth on silicon (111) substrate using thermal evaporation and continuing with dry oxidation of Sn at 225 °C. Thermal evaporation for high purity Sn was conducted by maintain the current source as high as 40 ampere. The quality of SnO{sub 2} on Si(111) and the characteristic of carbon thin film on SnO{sub 2} were analized by mean XRD, FTIR and Raman spectra. XRD analysis shows that SnO{sub 2} film is growth uniformly on Si(111). FTIR and Raman spectra confirm the formation of thin film carbon on SnO{sub 2}. Additionally, thermal annealing for some sample series have been performed to study their structural stability. The change of atomic structure due to thermal annealing were analized by Raman and XRD spectra.

36 MATERIALS SCIENCE↗

Particle beam experiments for the analysis of reactive sputtering processes in metals and polymer surfaces

A beam experiment is presented to study heterogeneous reactions relevant to plasma-surface interactions in reactive sputtering applications. Atom and ion sources are focused onto the sample to expose it to quantified beams of oxygen, nitrogen, hydrogen, noble gas ions, and metal vapor. The heterogeneous surface processes are monitored in situ by means of a quartz crystal microbalance and Fourier transform infrared spectroscopy. Two examples illustrate the capabilities of the particle beam setup: oxidation and nitriding of aluminum as a model of target poisoning during reactive magnetron sputtering, and plasma pre-treatment of polymers (PET, PP)

36 MATERIALS SCIENCE↗

Effects of boron dopants of Si (001) substrates on formation of Ge layers by sputter epitaxy method

The formation of Ge layers on boron-doped Si (001) substrates by our sputter epitaxy method has been investigated. The surface morphology of Ge layers grown on Si substrates depends on the substrate resistance, and flat Ge layers are obtained on Si substrates with 0.015 Ω cm resistivity. Highly boron-doped Si substrates cause a transition in the dislocation structure from complex dislocations with 60° dislocation glide planes to 90° pure-edge dislocations, resulting in the formation of flat Ge layers. Furthermore, we have found that the surface morphology of the Ge layers improves with increasing Ge layer thickness. Ge atoms migrating on the deposited Ge layers tend to position themselves at the reactive sites, where the reactivity is related to the number of bonding contacts between the Ge atom and the surface. This modifies the surface morphology, resulting in a flatter surface. Boron dopants together with the sputter epitaxy method effectively suppress the growth of Ge islands and result in the formation of flat Ge layers.

36 MATERIALS SCIENCE↗

Effects of substrate temperature, substrate orientation, and energetic atomic collisions on the structure of GaN films grown by reactive sputtering

The combined effects of substrate temperature, substrate orientation, and energetic particle impingement on the structure of GaN films grown by reactive radio-frequency magnetron sputtering are investigated. Monte-Carlo based simulations are employed to analyze the energies of the species generated in the plasma and colliding with the growing surface. Polycrystalline films grown at temperatures ranging from 500 to 1000 °C clearly showed a dependence of orientation texture and surface morphology on substrate orientation (c- and a-plane sapphire) in which the (0001) GaN planes were parallel to the substrate surface. A large increase in interplanar spacing associated with the increase in both a- and c-parameters of the hexagonal lattice and a redshift of the optical bandgap were observed at substrate temperatures higher than 600 °C. The results showed that the tensile stresses produced during the film's growth in high-temperature deposition ranges were much larger than the expected compressive stresses caused by the difference in the thermal expansion coefficients of the film and substrate in the cool-down process after the film growth. The best films were deposited at 500 °C, 30 W and 600 °C, 45 W, which corresponds to conditions where the out diffusion from the film is low. Under these conditions the benefits of the temperature increase because of the decrease in defect density are greater than the problems caused by the strongly strained lattice that occurr at higher temperatures. The results are useful to the analysis of the growth conditions of GaN films by reactive sputtering.

36 MATERIALS SCIENCE↗

Third-order nonlinear optical response of colloidal gold nanoparticles prepared by sputtering deposition

The nonlinear optical responses of gold nanoparticles dispersed in castor oil produced by sputtering deposition were investigated, using the thermally managed Z-scan technique. Particles with spherical shape and 2.6 nm of average diameter were obtained and characterized by transmission electron microscopy and small angle X-ray scattering. This colloid was highly stable, without the presence of chemical impurities, neither stabilizers. It was observed that this system presents a large refractive third-order nonlinear response and a negligible nonlinear absorption. Moreover, the evaluation of the all-optical switching figures of merit demonstrated that the colloidal nanoparticles prepared by sputtering deposition have a good potential for the development of ultrafast photonic devices.

36 MATERIALS SCIENCE↗