Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ROUGHNESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Spatial simulation of boundary layer instability - Effects of surface roughness

The effects of an isolated, two-dimensional roughness element on the spatial development of instability waves in boundary layers are investigated by numerically integrating the two-dimensional, time-dependent, incompressible Navier-Stokes equations, using a finite difference/Chebyshev discretization. It is shown that (high) inviscid frequencies have higher growth rates than Tollmien-Schlichting frequencies, indicating that disturbances growing in the separation zone are controlled by the inviscid instability of the shear layer at the edge of the separation zone.

Danabasoglu, G.↗
NASA NTRS1993

Quartz dissolution. I - Negative crystal experiments and a rate law. II - Theory of rough and smooth surfaces

The range of the measured quartz dissolution rates, as a function of temperature and pOH, extent of saturation, and ionic strength, is extended to cover a wider range of solution chemistries, using the negative crystal methodology of Gratz et al. (1990) to measure the dissolution rate. A simple rate law describing the quartz dissolution kinetics above the point of zero charge of quartz is derived for ionic strengths above 0.003 m. Measurements were performed on some defective crystals, and the mathematics of step motion was developed for quartz dissolution and was compared with rough-face behavior using two different models.

Gratz, Andrew J.↗
NASA NTRS1992

A comparison between backscattering models for rough surfaces

The ease of applicability of three scattering models is examined. This is accomplished by considering the time taken to numerically evaluate these models and by comparing their predictions as a function of surface roughness, frequency, incident angle and polarization with the moment-method solution in two dimensions. The complexity of the analytic models in three dimensions and their analytic reduction to high- and low-frequency regions are also compared. The selected models are an integral equation model (IEM), a full wave model (FWM), and the phase perturbation model (PPM). It is noted that in three dimensions, the full-wave model requires an evaluation of a tenfold integral and the phase perturbation model requires a fourfold and a twofold integral, whereas the integral equation model is an algebraic equation in like polarization under single scattering conditions. It is found that both the IEM and PPM agree with the moment-method solution from low to high frequencies numerically.

Chen, K. S.↗
NASA NTRS1992

Circular and linear polarization inverse SAR imaging of simple deterministic targets and statistically known randomly rough surfaces using constant and varying illumination

In order to study mechanisms of scattering and their relative contributions to synthetic aperture radar (SAR) and inverse SAR images, a special measurement facility has been constructed. It can be used to generate images in which the target is illuminated from a constant direction as the receiver is rotated in azimuth, and the target is illuminated from various directions as the receiver is rotated in azimuth. The imaging system performance is discussed, and images obtained using both approaches are compared, for a variety of simple targets and statistically known randomly rough surfaces.

Bredow, J. W.↗
NASA NTRS1993

A lag model for turbulent boundary layers developing over rough bleed surfaces

Boundary layer mass removal (bleed) through spanwise bands of holes on a surface is used to prevent or control separation and to stabilize the normal shock in supersonic inlets. The addition of a transport equation lag relationship for eddy viscosity to the rough wall algebraic turbulence model of Cebeci and Chang was found to improve agreement between predicted and measured mean velocity distributions downstream of a bleed band. The model was demonstrated for a range of bleed configurations, bleed rates, and local free stream Mach numbers. In addition, the model was applied to the boundary layer development over acoustic lining materials for the inlets and nozzles of commercial aircraft. The model was found to yield accurate results for integral boundary layer properties unless there was a strong adverse pressure gradient.

Lee, J.↗
NASA NTRS1957

Rough-water Impact-load Investigation of a Chine-immersed V-bottom Model Having a Dead-rise Angle of 10 Degrees

A hydrodynamic rough-water impact-loads investigation of a fixed-trim V-bottom float with a beam-loading coefficient of 5.78 and dead-rise angle of 10 degrees was made at the Langley impact basin. The size of the waves varied from approximately 10 to 60 feet in length and 1 to 2 feet in height. Time histories were obtained showing the position of the model relative to the wave throughout the impact and typical examples are presented. The load coefficient was found to vary primarily with the slope of the impacting wave.

HYDRODYNAMIC CONFIGURATIONS - GENERAL STUDIES↗
NASA NTRS1957

Effects of airplane flexibility on wing bending strains in rough air

Some results on the effects of wing flexibility on wing bending strains as determined from flight tests of a Boeing B-29 and a Boeing B-47A airplane in rough air are presented. Results from an analytical study of the flexibility effects on the B-29 wing strains are compared with the experimental results. Both the experimental and calculated results are presented as frequency-response functions of the bending strains at various spanwise wing stations to gust disturbances. In addition, some indirect evidence of the effect of spanwise variations in turbulence on the response of the B-47A airplane is presented.

LOADS, GUST - WINGS↗
NASA NTRS1947

Investigations of Effects of Surface Temperature and Single Roughness Elements on Boundary-Layer Transition

The laminar boundary layer and the position of the transition point were investigated on a heated flat plate. It was found that the Reynolds number of transition decreased as the temperature of the plate is increased. It is shown from simple qualitative analytical considerations that the effect of variable viscosity in the boundary layer due to the temperature difference produces a velocity profile with an inflection point if the wall temperature is higher than the free-stream temperature. This profile is confirmed by measurements. The instability of inflection-point profiles is discussed. Studies of the flow in the wake of large, two-dimensional roughness elements are presented. It is shown that a boundary-layer can separate and reattach itself to the wall without having transition take place.

Liepmann, Hans W↗
NASA NTRS1954

Relation Between Roughness of Interface and Adherence of Porcelain Enamel to Steel

Porcelain-enamel ground coats were prepared and applied under conditions that gave various degrees of adherence between enamel and a low-carbon steel (enameling iron). The variations in adherence were produced by (a) varying the amount of cobalt-oxide addition in the frit, (b) varying the type of metallic-oxide addition in the frit, keeping the amount constant at 0.8 weight percent, (c) varying the surface treatment of the metal before application of the enamel, by pickling, sandblasting, and polishing, and (d) varying the time of firing of the enamel containing 0.8 percent of cobalt oxide. Specimens of each enamel were given the standard adherence test of the Porcelain Enamel Institute. Metallographic sections were made on which the roughness of interface was evaluated by counting the number of anchor points (undercuts) per centimeter of specimen length and also by measuring the length of the interface and expressing results as the ratio of this length to the length of a straight line parallel to the over-all direction of the interface.

Richmond, J C↗
NASA NTRS1994

Measuring Roughnesses Of Optical Surfaces

Report discusses use of scanning tunneling microscopy and atomic force microscopy to measure roughnesses of optical surfaces. These techniques offer greater spatial resolution than other techniques. Report notes scanning tunneling microscopes and atomic force microscopes resolve down to 1 nm.

Coulter, Daniel R.↗
NASA NTRS1994

Measurement of aerodynamic roughness using radar backscatter over vegetated surfaces

The importance of the measurement of wind fields is discussed. Wind regime data can be used to infer the amount and type of wind induced (aerolian) transport of sand and dust, or to establish global circulation models, for example on other planets. Since local measurements are costly and often impossible, it is desired to infer such data from remotely sensed information. A potential mechanism for remotely inferring the wind regime by using synthetic aperture radar data to describe the roughness of the surface is described. A project to estimate the practicality of using such a mechanism is described. An experiment that extends the mechanism to vegetated sites, where the goal is to measure potential for erosion, is reported.

Wall, S. D.↗
NASA NTRS1994

Surface roughness measurements

The Optics Division is currently in the research phase of producing grazing-incidence mirrors to be used in x-ray detector applications. The traditional method of construction involves labor-intensive glass grinding. This also culminates in a relatively heavy mirror. For lower resolution applications, the mirrors may be of a replicated design which involves milling a mandrel as a negative of the final shape and electroplating the cylindrical mirror onto it. The mirror is then separated from the mandrel by cooling. The mandrel will shrink more than the 'shell' (mirror) allowing it to be pulled from the mandrel. Ulmer (2) describes this technique and its variations in more detail. To date, several mirrors have been tested at MSFC by the Optical Fabrication Branch by focusing x-ray energy onto a detector with limited success. Little is known about the surface roughness of the actual mirror. Hence, the attempt to gather data on these surfaces. The test involves profiling the surface of a sample, replicating the surface as described above, and then profiling the replicated surface.

Howard, Thomas G.↗
NASA NTRS1959

Study of Taxiing Problems Associated with Runway Roughness

This paper briefly summarizes available statistical data on airplane taxi operations, examines the profiles and power spectra of four selected runways and taxiways covering a wide range of surface roughness, considers (on the basis of theoretical and experimental results) the loads resulting from taxiing on such runways over a range of speeds and, by synthesis of the aforementioned results, proposes new criteria for runway and taxiway smoothness which are applicable to new construction and may also be used as a guide for determining when repairs are necessary.

Milwitzky, Benjamin↗
NASA NTRS1965

Response of a WB-47E Airplane to Runway Roughness at Eielson AFB, Alaska, September 1964

An investigation has been conducted to measure the response of a WB-47E airplane to the roughness of the runway at Eielson AFB, Alaska. The acceleration level in the pilot's compartment and the pitching oscillation of the airplane were found to be sufficiently high to possibly cause pilot discomfort and have an adverse effect on the precision of take-off.

Morris, Garland J.↗
NASA NTRS1992

Variable Property Flow in Rectangular Ducts with Repeated Rectangular Rib Roughness

PHOENICS was used to simulate turbulent flow of supercritical hydrogen through asymmetrically heated rectangular ducts with one side rib-roughened, in order to provide design data for active cooling systems of hypersonic aircraft where the hydrogen fuel is used as coolant. Variable property and conjugate heat transfer effects were considered. The computations using PHOENICS required provision of property sub-routines for supercritical hydrogen, a low-Reynolds number form of the k-epsilon turbulence model, a rough-wall wall function and a procedure for calculating proper diffusion coefficients at the fluid-solid interface. The effect of each design variable such as width and height of duct and wall thickness, on pressure drop and maximum wall temperature was investigated. PHOENICS version 1.4 was used on an IBM 3090 computer.

Youn, B.↗
NASA NTRS1998

Attachment-Line Transition Due to Roughness on a 76 Degree Swept Cylinder at Mach 1.6

Experiments were conducted on a 76 deg. swept cylinder to establish the conditions for the attachment-line transition process with, and without, surface roughness in a low-disturbance ("quiet"), Mach number 1.6 flow. Local flow parameters were estimated from pressure measurements. These were in good agreement with predictions from an Euler code (CFL3D) and a boundary layer code (BL3D). Hot-wires and Schlieren photography were used to determine the state of the boundary layer. It was found that, for a near-adiabatic wall condition and a smooth surface, the attachment-line, boundary-layer remained laminar up to the highest attainable Reynolds number (R-bar of 790). Transition under the influence of trip wires was found to depend on wind-tunnel disturbance levels and the onset conditions have been established. Results suggest that current design practice, which is based upon data from conventional ("noisy") tunnels, may be highly conservative.

Coleman, Colin P.↗
NASA NTRS1999

MOLA-derived Roughness Data Used to Predict Surface Scattering for Mars Subsurface Radar Sounding

The Mars Express orbiter, to be launched by the European Space Agency in 2003, will carry a low-frequency radar sounding instrument, MARSIS (Mars Advanced Radar for Subsurface and Ionospheric Sounding). The primary goal of MARSIS is to map the distribution of water, both solid and (if present) liquid, in the upper several km of the martian crust. Detecting discontinuities in the crust, such as an ice-water transition, presents many challenges for a Mars orbital radar sounder. One challenge that must be overcome is the presence of radar scattering (echoes) from the surface of Mars, expected to be detected by the sounder antennas at the same time as any echoes aris-ing from subsurface interfaces. As the transmitted spherical wavefront spreads within the crust of Mars,. it also interacts with surface topography at off-nadir positions, creating a "clutter" signal that can mask the subsurface echoes. The MARSIS instrument will utilize Doppler filtering to limit the off-nadir clutter in the along-track direction, and a nadir-null secondary antenna to identify strong off-nadir clutter from the cross-track direction. To evaluate the effects of off-nadir surface clutter and the capability of these schemes to reduce the clutter, it is necessary to predict the range of scattering behavior that may be expected from martian surface topography. In this paper, we utilize Mars Orbital Laser Altimeter (MOLA) data from the current Mars Global Surveyor mission to characterize the topographic roughness of a variety of martian terrain types, at scales relevant to the MARSIS clutter problem. Segments of MOLA altimetry profiles are reduced to the topographic parameters rms slope and fractal dimension, which then are used as inputs to a near-nadir radar scattering model to predict the strength of the clutter signal. Additional information is contained in the original extended abstract.

Plaut, J. J.↗