Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “QUALITY FACTOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

High-Q microsphere resonators for angular velocity sensing in gyroscopes

A resonator gyroscope based on the Sagnac effect is proposed using a core unit that is generated by water-hydrogen flame melting. The relationship between the quality factor Q and diameter D is revealed. The Q factor of the spectral lines of the microsphere cavity coupling system, which uses tapered fibers, is found to be 10{sup 6} or more before packaging with a low refractive curable ultraviolet polymer, although it drops to approximately 10{sup 5} after packaging. In addition, a rotating test platform is built, and the transmission spectrum and discriminator curves of a microsphere cavity with Q of 3.22×10{sup 6} are measured using a semiconductor laser (linewidth less than 1 kHz) and a real-time proportional-integral circuit tracking and feedback technique. Equations fitting the relation between the voltage and angular rotation rate are obtained. According to the experimentally measured parameters, the sensitivity of the microsphere-coupled system can reach 0.095{sup ∘}/s.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Preparation and microwave dielectric properties of Li{sub 3}(Mg{sub 0.92}Zn{sub 0.08}){sub 2}NbO{sub 6}–Ba{sub 3}(VO{sub 4}){sub 2} composite ceramics for LTCC applications

Highlights: • Microwave properties of ϵ{sub r} ∼ 16.3, Q × f ∼ 50,084 GHz and τ{sub f} ∼ 1.5 ppm/°C are achieved. • The τ{sub f} value of the LMZN ceramic can be adjusted to near zero by adding BV. • The LMZN–BV composite ceramic can be well sintered at a relatively low temperature. • The composite ceramic has a good chemical compatibility with Ag electrode. - Abstract: In this work, the (1 − x)Li{sub 3}(Mg{sub 0.92}Zn{sub 0.08}){sub 2}NbO{sub 6}–xBa{sub 3}(VO{sub 4}){sub 2} (x = 0.1–0.35) ceramics were prepared via a conventional solid state reaction route. The phase composition, microstructure and microwave dielectric properties were investigated by an X-ray diffractometer (XRD), a scanning electron microscope and a network analyzer. The XRD results indicated that the Li{sub 3}(Mg{sub 0.92}Zn{sub 0.08}){sub 2}NbO{sub 6} and Ba{sub 3}(VO{sub 4}){sub 2} phases could well coexist without forming any secondary phases. The dielectric constant (ϵ{sub r}) and quality factor (Q × f) values of the Li{sub 3}(Mg{sub 0.92}Zn{sub 0.08}){sub 2}NbO{sub 6} ceramic decreased with the addition of Ba{sub 3}(VO{sub 4}){sub 2} phase, however its temperature coefficient of resonant frequency (τ{sub f}) value was improved significantly. Excellent microwave dielectric properties of ϵ{sub r} ∼ 16.3, Q × f ∼ 50,084 GHz (at 8.64 GHz) and τ{sub f} ∼ 1.5 ppm/°C were achieved for the x = 0.3 sample when sintered at 950 °C for 4 h. The chemical compatibility with Ag electrode indicated that the 0.7Li{sub 3}(Mg{sub 0.92}Zn{sub 0.08}){sub 2}NbO{sub 6}–0.3Ba{sub 3}(VO{sub 4}){sub 2} composite ceramic would be a promising material for the low temperature cofired ceramic applications.

36 MATERIALS SCIENCE↗

Lasing in optimized two-dimensional iron-nail-shaped rod photonic crystals

We demonstrated lasing at the Γ-point band-edge (BE) modes in optimized two-dimensional iron-nail-shaped rod photonic crystals by optical pulse pumping at room temperature. As the radius of the rod increased quadratically toward the edge of the pattern, the quality factor of the Γ-point BE mode increased up to three times, and the modal volume decreased to 56% compared with the values of the original Γ-point BE mode because of the reduction of the optical loss in the horizontal direction. Single-mode lasing from an optimized iron-nail-shaped rod array with an InGaAsP multiple quantum well embedded in the nail heads was observed at a low threshold pump power of 160 μW. Real-image-based numerical simulations showed that the lasing actions originated from the optimized Γ-point BE mode and agreed well with the measurement results, including the lasing polarization, wavelength, and near-field image.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

High etching rates of bulk Nb in Ar/Cl{sub 2} microwave discharge

Plasma-based Nb surface treatment provides an excellent opportunity to eliminate surface imperfections and increase the cavity quality factor in important applications such as particle accelerators and cavity quantum electrodynamics, as well as Josephson junctions. In this study, plasma etching of bulk Nb is performed on the surface of disk-shaped samples with the goal of eliminating nonsuperconductive pollutants in the penetration depth region and the mechanically damaged surface layer. The authors have demonstrated that in the microwave glow discharge, an etching rate of 1.5 {mu}m/min can be achieved using Cl{sub 2} as a reactive gas. The influence of plasma parameters such as input power, pressure, and concentration of the reactive gas on the etching rate is determined. Simultaneously, plasma emission spectroscopy was used to estimate the densities of Cl, Cl{sup +}, and Cl{sub 2} under various plasma conditions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Linking sintering stresses to nano modification in the microstructure of BaLa4Ti4O15 by transmission electron microscopy

Highlights: • by systematic HRTEM studies we link the microstructural changes in BLT ceramics to the external pressure applied during sintering; • we developed a mechanistic understanding of the role of stress in sintering; • external stresses during sintering affect the microstructural development at the nanoscale level, being responsible for the creation of higher defective bulk and grain boundary regions; • observation of high density of stacking faults (which generally arrises due to the Ti vacancy layers) indicates that the applied stress is modifying the stacking of AO{sub 3} layers of BLT which in turn creates Ti vacancy layer and stacking faults; • stress assisted sintering has, therefore, the potential to be used as a tool to design microstructures and achieve tailored properties, as suggested from our previous results in BLT and BNT. - Abstract: High quality factor and a temperature stable resonant frequency make BaLa{sub 4}Ti{sub 4}O{sub 15} (BLT) ceramics attractive materials for microwave applications. Aiming to exploit the effects of external stresses on the development of textured and anisotropic microstructures to optimise MW properties, the influence of applied external pressure during sintering of BLT ceramics is analysed. HRTEM and geometric phase analysis (GPA) showed that stresses applied during sintering, trigger the nucleation and growth of faults hypothesised to be due to the errors in the AO{sub 3} layer (basal plane) stacking sequence of the hexagonal perovskite structure. The results reveal a strong correlation between the high concentration of structural defects and the development of anisotropic microstructures, which tune the properties of BLT. Stresses applied during sintering are therefore a promising tool to design material properties.

36 MATERIALS SCIENCE↗

Radiative rate modification in CdSe quantum dot-coated microcavity

Whispering gallery modes (WGMs) of the microparticles with spherical or cylindrical symmetry have exceptionally high quality factors and small mode volume. Quantum dots (QDs) are zero dimensional systems with variable band gap as well as luminescent properties with applications in photonics. In this paper, the WGMs have been observed in the luminescence spectra of CdSe QD-coated single silica microspheres. Theoretical estimations of variation of resonance frequency, electric field, and Q-values have been done for a multilayer coating of QDs on silica microspheres. Observed WGMs have been identified for their mode number and polarization using Mie theory. Broadening of modes due to material absorption has been observed. Splitting of WGMs has also been observed due to coherent coupling of counter propagating waves in the microcavity due to the presence of QDs. At room temperature, the time-resolved study indicates the modification of the radiative rate due to coupling of WGMs of the microcavity-QD hybrid system.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Ultrasensitive detection of mode splitting in active optical microcavities

Scattering-induced mode splitting in active microcavities is demonstrated. Below the lasing threshold, quality factor enhancement by optical gain allows resolving, in the wavelength-scanning transmission spectrum, of resonance dips of the split modes which otherwise would not be detected in a passive resonator. In the lasing regime, mode splitting manifests itself as two lasing modes with extremely narrow linewidths. Mixing these lasing modes in a detector leads to a heterodyne beat signal whose frequency corresponds to the mode-splitting amount. Lasing regime not only allows ultra-high sensitivity for mode-splitting measurements but also provides an easily accessible scheme by eliminating the need for wavelength scanning around resonant modes. Mode splitting in active microcavities has an immediate impact in enhancing the sensitivity of subwavelength scatterer detection and in studying light-matter interactions in a strong-coupling regime.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Detection of ethylene gas in exhaled breath of people living in landfill using CO{sub 2} laser photoacoustic spectroscopy with multicomponent analysis

The photoacoustic spectrometer (PAS) had been built and the performance had been determined. The research was based on the conversion of the absorbed middle infra red (IR) radiation by gas confined in a closed PAS cell into standing acoustic wave, which could be detected by a suitable electroacoustic transducer such as a microphone. The lowest detection limit for this setup was (57,1 ± 0,3) ppb and quality factor was (14,5 ± 0,6) for ethylene gas in 10P14 CO{sub 2} laser line. Then, this PAS was used to measure of ethylene gas concentration in breath sample of people living in near the Piyungan Bantul Yogyakarta landfill. The result from multicomponent analysis showed that PAS enable to measure the lowest concentration of volatile organic compound (VOC), such as ethylene, which occured on ambien air in Piyungan landfill. Variaty of distance area applied in this research. In the range of ±0,5 km from landfill, we obtained the concentration of ethylene gas concentration for human breath was (1,520 ± 0,002) ppm, while in the range of ±45 km, the ethylene gas concentration for human breath was (0,424 ± 0,002) ppm. Ethylene gas concentrations in exhaled gas decreased along with increasing distance variation of the landfill.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Crystal structures and microwave dielectric properties of Zn,W co-substituted BaTiO{sub 3} perovskite ceramics

Zn,W co-substituted BaTiO{sub 3} perovskite ceramics with compositions of Ba[Ti{sub 1-x}(Zn{sub 1/2}W{sub 1/2}){sub x}]O{sub 3} (x=0.40-1.00) were synthesized by the conventional solid-state reaction method and studied by X-ray diffraction and dielectric measurements. Their structures transferred from cubic (x=0.40) with space group Pm3{sup Macron }m to hexagonal (x=0.55-0.60) with P6{sub 3}/mmc, and then to cubic double pervoskite (x=1.00) with Fm3{sup Macron }m. The refinement results of sample (x=0.60) revealed that the negative and positive charge centers are not consistent with each other in the face-sharing oxygen octahedra. Compared with the cubic perovskites, the hexagonal ones had the increased quality factor (Q Multiplication-Sign f), the decreased dielectric constant ({epsilon}{sub r}), and especially the near-zero temperature coefficient of resonant frequency ({tau}{sub f}), whose absolute values were less than 5 ppm/ Degree-Sign C. The relationships between structures and properties were discussed. - Graphical abstract: The departure of the negative and positive charge centers in the face-sharing oxygen octahedra of hexagonal unit cell. Highlights: Black-Right-Pointing-Pointer A phase transition from simple cubic to hexagonal and then to cubic double pervoskite occurred. Black-Right-Pointing-Pointer Refinement results prove that spontaneous dipoles present in face-sharing oxygen octahedra. Black-Right-Pointing-Pointer Hexagonal perovskites had higher Q Multiplication-Sign f, nearer-zero {tau}{sub f}, and lower {epsilon}{sub r} than the cubic ones. Black-Right-Pointing-Pointer On the presence of the hexagonal perovskite, |{tau}{sub f}| was less than 5 ppm/ Degree-Sign C.

36 MATERIALS SCIENCE↗

An X-Ray Periodicity of ∼1.8 hr in Narrow-line Seyfert 1 Galaxy Mrk 766

In the narrow-line Seyfert 1 galaxy Mrk 766, a quasi-periodic oscillation (QPO) signal with a period of ∼6450 s is detected in the XMM-Newton data collected on 2005 May 31. This QPO signal is highly statistically significant at the ∼5σ confidence level, with a quality factor of Q=f/Δf>13.6. The X-ray intensity changed by a factor of 3, with a root mean square fractional variability of 14.3%. Furthermore, this QPO signal is present in the data of all three EPIC detectors and two RGS cameras and its frequency follows the f{sub QPO}–M{sub BH} relation spanning from stellar-mass to supermassive black holes. Interestingly, a possible QPO signal with a period of ∼4200 s had been reported in the literature. The frequency ratio of these two QPO signals is ∼3:2. Our result is also in support of the hypothesis that the QPO signals can just be transient. The spectral analysis reveals that the contribution of the soft excess component below ∼1 keV is different between epochs with and without QPO. This property, as well as the former frequency ratio, are well-detected in X-ray BH binaries, which may shed some light on the physical origins of our event.

79 ASTRONOMY AND ASTROPHYSICS↗

Plasma treatment of bulk niobium surface for superconducting rf cavities: Optimization of the experimental conditions on flat samples

Accelerator performance, in particular the average accelerating field and the cavity quality factor, depends on the physical and chemical characteristics of the superconducting radio-frequency (SRF) cavity surface. Plasma based surface modification provides an excellent opportunity to eliminate nonsuperconductive pollutants in the penetration depth region and to remove the mechanically damaged surface layer, which improves the surface roughness. Here we show that the plasma treatment of bulk niobium (Nb) presents an alternative surface preparation method to the commonly used buffered chemical polishing and electropolishing methods. We have optimized the experimental conditions in the microwave glow discharge system and their influence on the Nb removal rate on flat samples. We have achieved an etching rate of 1.7 μm/min⁡ using only 3% chlorine in the reactive mixture. Combining a fast etching step with a moderate one, we have improved the surface roughness without exposing the sample surface to the environment. We intend to apply the optimized experimental conditions to the preparation of single cell cavities, pursuing the improvement of their rf performance.

43 PARTICLE ACCELERATORS↗

Tunneling study of SRF cavity-grade niobium.

Niobium, with its very high H{sub C1}, has been used in superconducting radio frequency (SRF) cavities for accelerator systems for 40 years with continual improvement. The quality factor of cavities (Q) is governed by the surface impedance R{sub BCS}, which depends on the quasiparticle gap, delta, and the superfluid density. Both of these parameters are seriously affected by surface imperfections (metallic phases, dissolved oxygen, magnetic impurities). Loss mechanism and surface treatments of Nb cavities found to improve the Q factor are still unsolved mysteries. We present here an overview of the capabilities of the point contact tunneling spectroscopy and Atomic layer deposition methods and how they can help understanding the High field Q-drop and the mild baking effect. Tunneling spectroscopy was performed on Nb pieces from the same processed material used to fabricate SRF cavities. Air exposed, electropolished Nb exhibited a surface superconducting gap Delta = 1.55 meV, characteristic of clean, bulk Nb, however the tunneling density of states (DOS) was broadened significantly. Nb pieces treated with the same mild baking used to improve the Q-slope in SRF cavities revealed a much sharper DOS. Good fits to the DOS are obtained using Shiba theory suggesting that magnetic scattering of quasiparticles is the origin of the degraded surface superconductivity and the Q-slope problem of Nb SRF cavities.

43 PARTICLE ACCELERATORS↗

Improving Earthquake-Explosion Discrimination using Attenuation Models of the Crust and Upper Mantle

In the past year, we have made significant progress on developing and calibrating methodologies to improve earthquake-explosion discrimination using high-frequency regional P/S amplitude ratios. Closely-spaced earthquakes and explosions generally discriminate easily using this method, as demonstrated by recordings of explosions from test sites around the world. In relatively simple geophysical regions such as the continental parts of the Yellow Sea and Korean Peninsula (YSKP) we have successfully used a 1-D Magnitude and Distance Amplitude Correction methodology (1-D MDAC) to extend the regional P/S technique over large areas. However in tectonically complex regions such as the Middle East, or the mixed oceanic-continental paths for the YSKP the lateral variations in amplitudes are not well predicted by 1-D corrections and 1-D MDAC P/S discrimination over broad areas can perform poorly. We have developed a new technique to map 2-D attenuation structure in the crust and upper mantle. We retain the MDAC source model and geometrical spreading formulation and use the amplitudes of the four primary regional phases (Pn, Pg, Sn, Lg), to develop a simultaneous multi-phase approach to determine the P-wave and S-wave attenuation of the lithosphere. The methodology allows solving for attenuation structure in different depth layers. Here we show results for the P and S-wave attenuation in crust and upper mantle layers. When applied to the Middle East, we find variations in the attenuation quality factor Q that are consistent with the complex tectonics of the region. For example, provinces along the tectonically-active Tethys collision zone (e.g. Turkish Plateau, Zagros) have high attenuation in both the crust and upper mantle, while the stable outlying regions like the Indian Shield generally have low attenuation. In the Arabian Shield, however, we find that the low attenuation in this Precambrian crust is underlain by a high-attenuation upper mantle similar to the nearby Red Sea Rift. Applying this 2-D MDAC methodology with the new attenuation models can significantly improve earthquake-explosion discrimination using regional P/S amplitude ratios. We demonstrate applications of this technique, including a study at station NIL (Nilore, Pakistan) using broad area earthquakes and the 1998 Indian nuclear explosion using a number of regional amplitude ratio discriminants. We are currently applying the technique in the YSKP region as well.

58 GEOSCIENCES↗

Piezoelectricity and ferroelectricity of cellular polypropylene electrets films characterized by piezoresponse force microscopy

Cellular electrets polymer is a new ferroelectret material exhibiting large piezoelectricity and has attracted considerable attentions in researches and industries. Property characterization is very important for this material and current investigations are mostly on macroscopic properties. In this work, we conduct nanoscale piezoelectric and ferroelectric characterizations of cellular polypropylene (PP) films using piezoresponse force microscopy (PFM). First, both the single-frequency PFM and dual-frequency resonance-tracking PFM testings were conducted on the cellular PP film. The localized piezoelectric constant d{sub 33} is estimated to be 7–11pC/N by correcting the resonance magnification with quality factor and it is about one order lower than the macroscopic value. Next, using the switching spectroscopy PFM (SS-PFM), we studied polarization switching behavior of the cellular PP films. Results show that it exhibits the typical ferroelectric-like phase hysteresis loops and butterfly-shaped amplitude loops, which is similar to that of a poly(vinylidene fluoride) (PVDF) ferroelectric polymer film. However, both the phase and amplitude loops of the PP film are intensively asymmetric, which is thought to be caused by the nonzero remnant polarization after poling. Then, the D-E hysteresis loops of both the cellular PP film and PVDF film were measured by using the same wave form as that used in the SS-PFM, and the results show significant differences. Finally, we suggest that the ferroelectric-like behavior of cellular electrets films should be distinguished from that of typical ferroelectrics, both macroscopically and microscopically.

36 MATERIALS SCIENCE↗

YBa{sub 2}Cu{sub 3}O{sub 7} microwave resonators for strong collective coupling with spin ensembles

Coplanar microwave resonators made of 330 nm-thick superconducting YBa{sub 2}Cu{sub 3}O{sub 7} have been realized and characterized in a wide temperature (T, 2–100 K) and magnetic field (B, 0–7 T) range. The quality factor (Q{sub L}) exceeds 10{sup 4} below 55 K and it slightly decreases for increasing fields, remaining 90% of Q{sub L}(B=0) for B = 7 T and T = 2 K. These features allow the coherent coupling of resonant photons with a spin ensemble at finite temperature and magnetic field. To demonstrate this, collective strong coupling was achieved by using di(phenyl)-(2,4,6-trinitrophenyl)iminoazanium organic radical placed at the magnetic antinode of the fundamental mode: the in-plane magnetic field is used to tune the spin frequency gap splitting across the single-mode cavity resonance at 7.75 GHz, where clear anticrossings are observed with a splitting as large as ∼82 MHz at T = 2 K. The spin-cavity collective coupling rate is shown to scale as the square root of the number of active spins in the ensemble.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DISCOVERY OF HIGH-FREQUENCY QUASI-PERIODIC OSCILLATIONS IN THE BLACK HOLE CANDIDATE IGR J17091-3624

We report the discovery of 8.5{sigma} high-frequency quasi-periodic oscillations (HFQPOs) at 66 Hz in the Rossi X-ray Timing Explorer data of the black hole candidate IGR J17091-3624, a system whose X-ray properties are very similar to those of microquasar GRS 1915+105. The centroid frequency of the strongest peak is {approx}66 Hz, its quality factor above five, and its rms is between 4% and 10%. We found a possible additional peak at 164 Hz when selecting a subset of the data; however, at the 4.5{sigma} level we consider this detection marginal. These QPOs have hard spectrum and are stronger in observations performed between 2011 September and October, during which IGR J17091-3624 displayed for the first time light curves that resemble those of the {gamma} variability class in GRS 1915+105. We find that the 66 Hz QPO is also present in previous observations (4.5{sigma}), but only when averaging {approx}235 ks of relatively high count rate data. The fact that the HFQPOs frequency in IGR J17091-3624 matches surprisingly well with that seen in GRS 1915+105 raises questions on the mass scaling of QPOs frequency in these two systems. We discuss some possible interpretations; however, they all strongly depend on the distance and mass of IGR J17091-3624, both completely unconstrained today.

79 ASTRONOMY AND ASTROPHYSICS↗

TIDALLY HEATED TERRESTRIAL EXOPLANETS: VISCOELASTIC RESPONSE MODELS

Tidal friction in exoplanet systems, driven by orbits that allow for durable nonzero eccentricities at short heliocentric periods, can generate internal heating far in excess of the conditions observed in our own solar system. Secular perturbations or a notional 2:1 resonance between a hot Earth and hot Jupiter can be used as a baseline to consider the thermal evolution of convecting bodies subject to strong viscoelastic tidal heating. We compare results first from simple models using a fixed Quality factor and Love number, and then for three different viscoelastic rheologies: the Maxwell body, the Standard Anelastic Solid (SAS), and the Burgers body. The SAS and Burgers models are shown to alter the potential for extreme tidal heating by introducing the possibility of new equilibria and multiple response peaks. We find that tidal heating tends to exceed radionuclide heating at periods below 10-30 days, and exceed insolation only below 1-2 days. Extreme cases produce enough tidal heat to initiate global-scale partial melting, and an analysis of tidal limiting mechanisms such as advective cooling for earthlike planets is discussed. To explore long-term behaviors, we map equilibria points between convective heat loss and tidal heat input as functions of eccentricity. For the periods and magnitudes discussed, we show that tidal heating, if significant, is generally detrimental to the width of habitable zones.

79 ASTRONOMY AND ASTROPHYSICS↗

CONDITIONS OF PASSAGE AND ENTRAPMENT OF TERRESTRIAL PLANETS IN SPIN-ORBIT RESONANCES

The dynamical evolution of terrestrial planets resembling Mercury in the vicinity of spin-orbit resonances is investigated using comprehensive harmonic expansions of the tidal torque taking into account the frequency-dependent quality factors and Love numbers. The torque equations are integrated numerically with a small step in time, including the oscillating triaxial torque components but neglecting the layered structure of the planet and assuming a zero obliquity. We find that a Mercury-like planet with a current value of orbital eccentricity (0.2056) is always captured in 3:2 resonance. The probability of capture in the higher 2:1 resonance is approximately 0.23. These results are confirmed by a semi-analytical estimation of capture probabilities as functions of eccentricity for both prograde and retrograde evolutions of spin rate. As follows from analysis of equilibrium torques, entrapment in 3:2 resonance is inevitable at eccentricities between 0.2 and 0.41. Considering the phase space parameters at the times of periastron, the range of spin rates and phase angles for which an immediate resonance passage is triggered is very narrow, and yet a planet like Mercury rarely fails to align itself into this state of unstable equilibrium before it traverses 2:1 resonance.

79 ASTRONOMY AND ASTROPHYSICS↗