Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Proper motions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1950

Ditching Investigation of a 1/14-Scale Model of the Northrop C-125 Airplane

An investigation of a 1/14-scale dynamically similar model of the Northrop C-125 airplane was made to determine the ditching characteristics and proper ditching technique for the airplane. Various conditions of damage, landing attitude, flap setting, and speed were investigated. The behavior of the model was determined from visual observations, motion-picture records, and time-history deceleration records. The results of the investigation are presented in table form, photographs, and curves. It was concluded that the airplane should be ditched at a nose-high landing attitude (near 8 deg) with flaps full down. The fixed landing gear will cause the airplane to dive. The fuselage will be damaged and will probably flood rapidly. Longitudinal decelerations will be about 4g and the length of landing run will be about two fuselage lengths. If the main landing gear could be jettisonable or retractable the ditching characteristics would be greatly improved.

Fisher, Lloyd J.↗
NASA NTRS1984

Study to eliminate ground resonance using active controls

The effectiveness of active control blade feathering in increasing rotor body damping and the possibility to eliminate ground resonance instabilities were investigated. An analytical model representing rotor flapping and lead-lag degrees of freedom and body pitch, roll, longitudinal and lateral motion is developed. Active control blade feathering is implemented as state variable feedback through a conventional swashplate. The influence of various feedback states, feedback gain, and weighting between the cyclic controls is studied through stability and response analyses. It is shown that blade cyclic inplane motion, roll rate and roll acceleration feedback can add considerable damping to the system and eliminate ground resonance instabilities, which the feedback phase is also a powerful parameter, if chosen properly, it maximizes augmentation of the inherent regressing lag mode damping. It is shown that rotor configuration parameters, like blade root hinge offset, flapping stiffness, and precone considerably influence the control effectiveness. It is found that active control is particularly powerful for hingeless and bearingless rotor systems.

Straub, F. K.↗
NASA NTRS2003

The Role of Visual Cues in Microgravity Spatial Orientation

In weightlessness, astronauts must rely on vision to remain spatially oriented. Although gravitational down cues are missing, most astronauts maintain a subjective vertical -a subjective sense of which way is up. This is evidenced by anecdotal reports of crewmembers feeling upside down (inversion illusions) or feeling that a floor has become a ceiling and vice versa (visual reorientation illusions). Instability in the subjective vertical direction can trigger disorientation and space motion sickness. On Neurolab, a virtual environment display system was used to conduct five interrelated experiments, which quantified: (a) how the direction of each person's subjective vertical depends on the orientation of the surrounding visual environment, (b) whether rolling the virtual visual environment produces stronger illusions of circular self-motion (circular vection) and more visual reorientation illusions than on Earth, (c) whether a virtual scene moving past the subject produces a stronger linear self-motion illusion (linear vection), and (d) whether deliberate manipulation of the subjective vertical changes a crewmember's interpretation of shading or the ability to recognize objects. None of the crew's subjective vertical indications became more independent of environmental cues in weightlessness. Three who were either strongly dependent on or independent of stationary visual cues in preflight tests remained so inflight. One other became more visually dependent inflight, but recovered postflight. Susceptibility to illusions of circular self-motion increased in flight. The time to the onset of linear self-motion illusions decreased and the illusion magnitude significantly increased for most subjects while free floating in weightlessness. These decreased toward one-G levels when the subject 'stood up' in weightlessness by wearing constant force springs. For several subjects, changing the relative direction of the subjective vertical in weightlessness-either by body rotation or by simply cognitively initiating a visual reorientation-altered the illusion of convexity produced when viewing a flat, shaded disc. It changed at least one person's ability to recognize previously presented two-dimensional shapes. Overall, results show that most astronauts become more dependent on dynamic visual motion cues and some become responsive to stationary orientation cues. The direction of the subjective vertical is labile in the absence of gravity. This can interfere with the ability to properly interpret shading, or to recognize complex objects in different orientations.

Oman, Charles M.↗
NASA NTRS2003

Compact, Pneumatically Actuated Filter Shuttle

A compact, pneumatically actuated filter shuttle has been invented to enable alternating imaging of a wind-tunnel model in two different spectral bands characteristic of the pressure and temperature responses of a pressure and temperature-sensitive paint. This filter shuttle could also be used in other settings in which there are requirements for alternating imaging in two spectral bands. Pneumatic actuation was chosen because of a need to exert control remotely (that is, from outside the wind tunnel) and because the power leads that would be needed for electrical actuation would pose an unacceptable hazard in the wind tunnel. The entire shuttle mechanism and its housing can be built relatively inexpensively [<$500 (prices as of year 2000)] from off-the-shelf parts. The shuttle mechanism (see Figure 1) is contained in a housing that has dimensions of 4 by 6 by 2 in. (about 10 by 15 by 5 cm). Two 2-in. (=5-cm)-diameter standard scientific-grade band-pass filters are mounted on sliding panels in a dual-track frame. The mechanism is positioned and oriented so the panels slide sideways with respect to the optical axis of a charge-coupled-device camera used for viewing the wind-tunnel model. The mechanism includes a pneumatic actuator connected to a linkage. The linkage converts the actuator stroke to a scissor-like motion that places one filter in front of the camera and the other filter out of the way. Optoelectronic sensors detect tabs on the sliding panels for verification of the proper positioning of the filters.

Leighy, Bradley D.↗
DOE OSTI2020

A Numerical Method for Determining the Elements of Circumbinary Orbits and Its Application to Circumbinary Planets and the Satellites of Pluto-Charon

Planets and satellites orbiting a binary system exist in the solar system and extrasolar planetary systems. Their orbits can be significantly different from Keplerian orbits, if they are close to the binary and the secondary-to-primary mass ratio is high. A proper description of a circumbinary orbit is in terms of the free eccentricity e {sub free} at the epicyclic frequency κ {sub 0}, forced eccentricity e {sub forced} at the mean motion n {sub 0}, and oscillations at higher frequencies forced by the non-axisymmetric components of the binary’s potential. We show that accurate numerical values for the amplitudes and frequencies of these terms can be extracted from numerical orbit integrations by applying fast Fourier transformation (FFT) to the cylindrical distance between the circumbinary object and the center of mass of the binary as a function of time. We apply this method to three Kepler circumbinary planets and the satellites of Pluto-Charon. For the satellite Styx of Pluto-Charon, the FFT results for κ {sub 0} and e {sub free} differ significantly from the first-order analytic value and the value reported by Showalter & Hamilton, respectively. We show that the deviation in κ {sub 0} is likely due to the effect of the 3:1 mean-motion resonance and discuss the implications of the lower value for e {sub free}.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

Trajectory of a flying plasma mirror traversing a target with density gradient

It has been proposed that laser-induced relativistic plasma mirror can accelerate if the plasma has a properly tailored density profile. Such accelerating plasma mirrors can serve as analog black holes to investigate Hawking evaporation and the associated information loss paradox. Here we reexamine the underlying dynamics of mirror motion in a graded-density plasma to provide an explicit trajectory as a function of the plasma density and its gradient. Specifically, a decreasing plasma density profile (down-ramp) along the direction of laser propagation would in general accelerate the mirror. In particular, a constant-plus-exponential density profile would generate the Davies–Fulling trajectory with a well-defined analog Hawking temperature, which is sensitive to the plasma density gradient but not to the density itself. Furthermore, we show that without invoking nano-fabricated thin-films, a much lower density gas target at, for example, ~1 × 10 17 cm -3 , would be able to induce an analog Hawking temperature, k B T H ~3.1 × 10 -2 eV, in the far-infrared region. We hope that this would help to better realize the experiment proposed by Chen and Mourou.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1979

Collimation of high-speed flow with thermal spread losses

The operation of the neutral beam collimator designed for the mass spectrometer inlet system of the Space Shuttle Induced Environment Contamination Monitor system is discussed. The collimator will allow selective views of a 10 deg half-angle conical volume of space so that backscattered molecules from within this volume can be measured and related to the column densities of outgassing species. Gas molecules which enter the collimator but do not have a view from the entrance orifice to the exit are directed to a gas getter and eliminated. The loss of properly directed molecules in the collimator due to their thermal distribution is calculated for the case of a directed flow, which would occur when the collimator is pointed in the direction of motion of the spacecraft. Inlet to outlet flux ratios are also computed as a function of angle of attack.

Taeusch, D. R.↗
NASA NTRS2012

The Rapidly Rotating Sun

Convection in the solar interior is thought to comprise structures at a continuum of scales, from large to small. This conclusion emerges from phenomenological studies and numerical simulations though neither covers the proper range of dynamical parameters of solar convection. In the present work, imaging techniques of time-distance helioseismology applied to observational data reveal no long-range order in the convective motion. We conservatively bound the associated velocity magnitudes, as a function of depth and the spherical-harmonic degree l to be 20-100 times weaker than prevailing estimates within the wavenumber band l < 60. The observationally constrained kinetic energy is approximately a thousandth of the theoretical prediction, suggesting the prevalence of an intrinsically different paradigm of turbulence. A fundamental question arises: what mechanism of turbulence transports the heat ux of a solar luminosity outwards? The Sun is seemingly a much faster rotator than previously thought, with advection dominated by Coriolis forces at scales l < 60.

Hanasoge, Shravan M.↗
NASA NTRS1973

Relative motion of near orbiting satellites.

The relative motion of two particles on adjacent orbits about the same primary has been investigated under the condition that both motions have the same period. The geometrical properties of the relative displacement and velocity traces, on representative planes, are studied. A complete state of the motion is given; and, the range and range-rate variations, over one or more orbits, are described. It has been found that cusps appear on some of the traces provided that a proper relationship exists between the eccentricity and inclination. (Here, one particle moves on a circular path while the second moves on an ellipse). The conditions for which cusps appear are given, and typical traces are shown.

Eades, J. B., Jr.↗
NASA NTRS1989

Improved Flow-Controlling Vortex Generator

Symmetrical tangential streams control flow of radial primary streams. Vortex generator uses small secondary stream of fluid to control normally-larger primary stream. Improved version of vortex generator described in "Variable Control Port for Fluidic Control Device," (NPO-16603). Secondary, or control, flows entering tangentially through diametrically opposite ports set up swirling motion restraining primary flow. Pressure of secondary fluid in relation to primary fluid controlling factor. Like valve, vortex generator varies rate of flow of primary fluid from maximum value down to zero. When properly designed, requires low pressure differential between primary and secondary streams and expends relatively small amount of secondary fluid.

Collins, Earl R., Jr.↗
NASA NTRS1992

The dimension of attractors underlying periodic turbulent Poiseuille flow

A lower bound on the Liapunov dimenison, D-lambda, of the attractor underlying turbulent, periodic Poiseuille flow at a pressure-gradient Reynolds number of 3200 is calculated, on the basis of a coarse-grained (16x33x8) numerical solution, to be approximately 352. Comparison of Liapunov exponent spectra from this and a higher-resolution (16x33x16) simulation on the same spatial domain shows these spectra to have a universal shape when properly scaled. On the basis of these scaling properties, and a partial exponent spectrum from a still higher-resolution (32x33x32) simulation, it is argued that the actual dimension of the attractor underlying motion of the given computational domain is approximately 780. It is suggested that this periodic turbulent shear flow is deterministic chaos, and that a strange attractor does underly solutions to the Navier-Stokes equations in such flows.

Keefe, Laurence↗
NASA NTRS1980

A mathematical model of post-instability in continuum mechanics

The post-instability can appear in the form of failure of hyperbolicity or in the form of cascade instability (stretching of vorticity in an inviscid fluid or instability of the Navier-Stokes equations). All the cases are characterized by an unlimited decrease of the scale of the motions, in the course of which the derivatives of the corresponding functions tend to infinity, though the functions themselves remain finite. Such an instability shows that the corresponding state of a continuum cannot be properly simulated by smooth functions. Hence, the original model must be corrected by giving up the requirement about differentiability and enlarging the class of functions. Applications to a model of an inviscid fluid and to a model of turbulence are discussed.

Zak, M.↗
NASA NTRS1984

Lewis Research Center spin rig and its use in vibration analysis of rotating systems

The Lewis Research Center spin rig was constructed to provide experimental evaluation of analysis methods developed under the NASA Engine Structural Dynamics Program. Rotors up to 51 cm (20 in.) in diameter can be spun to 16,000 rpm in vacuum by an air motor. Vibration forcing functions are provided by shakers that apply oscillatory axial forces or transverse moments to the shaft, by a natural whirling of the shaft, and by an air jet. Blade vibration is detected by strain gages and optical blade-tip motion sensors. A variety of analogy and digital processing equipment is used to display and analyze the signals. Results obtained from two rotors are discussed. A 56-blade compressor disk was used to check proper operation of the entire spin rig system. A special two-blade rotor was designed and used to hold flat and twisted plates at various setting and sweep angles. Accurate Southwell coefficients have been obtained for several modes of a flat plate oriented parallel to the plane of rotation.

Brown, G. V.↗
DOE OSTI2023

Bayesian Cloud Property Retrievals from ARM Active and Passive Measurements

The optimum use of the continuous measurements of thermodynamics, radiation, aerosols, clouds and precipitation from the DOE Atmospheric Radiation Measurement (ARM) program is key to achieve the DOE Atmospheric System Research (ASR)’s objectives. One of the key mission requirements is to retrieve cloud and precipitation properties, as well as vertical motion parameters, along the vertical cross- section defined by the profiling active sensors. Such retrievals are challenging to perform continuously in the entire spectrum of cloud and precipitation conditions due to the large natural microphysical and dynamical variability, the often-limited information content in the measurements, and the lack of proper characterization of measurement quality and uncertainty. Today, the acquisition of new remote and in-situ sensors by the ARM program creates opportunities to address the microphysical retrieval problem by exploiting new, more robust retrieval techniques and integrating various scattered advancements in both sensor techniques and retrieval algorithms. During this project, we constructed a robust Bayesian Markov chain Monte Carlo (MCMC) cloud property retrieval algorithm that includes a state of the art radar forward model. Our MCMC-based retrieval produces both the best estimate of height-resolved cloud and precipitation properties in the radar profile, as well as an estimate of the in-cloud vertical motion and turbulence. In addition, the MCMC algorithm automatically produces robust and flexible estimates of retrieval uncertainty. We tested the algorithm on several synthetic cloud profiles obtained from large eddy simulation (LES) models with bin-resolved microphysics.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1974

Vibration-translation energy transfer in anharmonic diatomic molecules. 1: A critical evaluation of the semiclassical approximation

The semiclassical approximation is applied to anharmonic diatomic oscillators in excited initial states. Multistate numerical solutions giving the vibrational transition probabilities for collinear collisions with an inert atom are compared with equivalent, exact quantum-mechanical calculations. Several symmetrization methods are shown to correlate accurately the predictions of both theories for all initial states, transitions, and molecular types tested, but only if coupling of the oscillator motion and the classical trajectory of the incident particle is considered. In anharmonic heteronuclear molecules, the customary semiclassical method of computing the classical trajectory independently leads to transition probabilities with anomalous low-energy resonances. Proper accounting of the effects of oscillator compression and recoil on the incident particle trajectory removes the anomalies and restores the applicability of the semiclassical approximation.

Mckenzie, R. L.↗
NASA NTRS1975

Vibration-translation energy transfer in anharmonic diatomic molecules. I - A comparative evaluation of the semiclassical approximation

The semiclassical approximation (quantum oscillator, classical path) is applied to anharmonic diatomic oscillators in excited initial states. Multistate numerical solutions giving the vibrational transition probabilities for collinear collisions with an inert atom are compared with equivalent, exact quantum-mechanical calculations. Several symmetrization methods are shown to correlate accurately the predictions of both theories for all initial states, transitions, and molecular types tested, but only if coupling of the oscillator motion and the classical trajectory of the incident particle is considered. In anharmonic heteronuclear molecules, the customary semiclassical method of computing the classical trajectory independently leads to transition probabilities with anomalous low-energy resonances. Proper accounting of the effects of oscillator compression and recoil on the incident particle trajectory removes the anomalies and restores the applicability of the semiclassical approximation.

Mckenzie, R. L.↗
NASA NTRS1994

Handling qualities of the High Speed Civil Transport

The low speed handling qualities of a High Speed Civil Transport class aircraft have been investigated by using data of the former Advanced Supersonic Transport (AST) 105. The operation of such vehicles in the airport terminal area is characterized by 'backside' performance. Main objectives of this research effort were: (Q) determination of the nature and magnitude of the speed instability associated with the backside of the thrust required curve; (2) confirmation of the validity of existing MIL-SPEC handling qualities criteria; (3) safety of operation of the vehicle in the event of autothrottle failure; and (4) correlation of required engine responsiveness with level of speed instability. Preliminary findings comprise the following: (1) The critical velocity for speed instability was determined to be 196 knots, well above the projected approach speed of 155 knots. This puts the vehicle far on the backside of its thrust required curve. While the aircraft can be configured to have static and dynamic stability at this trim point, a significant speed instability emerges, if a pilot or autopilot attempts flight path control with elevator and/or canard control surfaces only. This requires a properly configured autothrottle and/or variable aerodynamic drag devices which can provide speed stability; (2) An AST 105 type vehicle meets MIL-SPEC criteria only in part. While the damping criteria for phugoid and short period motion are met easily, the AST 105 falls short of the required minimum short period frequency, meaning that the HSCT is too sluggish in pitch to meet the military criteria. Obviously the military specification do not consider a vehicle with such high pitch inertia. With regard to speed stability and flight path stability criteria, the vehicle meets levels 2 and 3 of the military requirements, indicating that it would be landed safety with manual controls in case of an autothrottle failure, even though the pilot workload would be high; and (3) This requires quick thrust response to throttle adjustment, however. If the engine responsiveness is slow, the aircraft handling qualities are further deteriorated. Progress has been made in correlating required engine responses dyanmics with the given level of speed instability of the vehicle.

Solies, U. Peter↗
NASA NTRS1999

Calibration of the Geosar Dual Frequency Interferometric SAR

GeoSAR is an airborne, interferometric Synthetic Aperture Radar (INSAR) system for terrain mapping, currently under development by a consortium including NASA's Jet Propulsion Laboratory (JPL), Calgis, Inc., and the California Department of Conservation (CalDOC) with funding provided by the Topographic Engineering Center (TEC) of the U.S. Army Corps of Engineers and the Defense Advanced Research Projects Agency (DARPA). The radar simultaneously maps swaths on both sides of the aircraft at two frequencies, X-Band and P-Band. For the P-Band system, data is collected for two across track interferometric baselines and at the crossed polarization. The aircraft position and attitude are measured using two Honeywell Embedded GPS Inertial Navigation Units (EGI) and an Ashtech Z12 GPS receiver. The mechanical orientation and position of the antennas are actively measured using a Laser Baseline Metrology System (LBMS). In the GeoSAR motion measurement software, these data are optimally combined with data from a nearby ground station using Ashtech PNAV software to produce the position, orientation, and baseline information are used to process the dual frequency radar data. Proper calibration of the GeoSAR system is essential to obtaining digital elevation models (DEMS) with the required sub-meter level planimetric and vertical accuracies. Calibration begins with the determination of the yaw and pitch biases for the two EGI units. Common range delays are determined for each mode, along with differential time and phase delays between channels. Because the antennas are measured by the LBMS, baseline calibration consists primarily of measuring a constant offset between mechanical center and the electrical phase center of the antennas. A phase screen, an offset to the interferometric phase difference which is a function of absolute phase, is applied to the interferometric data to compensate for multipath and leakage. Calibration parameters are calculated for each of the ten processing modes, each of the operational bandwidths (80 and 160 MHZ), and each aircraft altitude. In this talk we will discuss the layout calibration sites, the synthesis of data from multiple flights to improve the calibration, methods for determining time and phase delays, and techniques for determining radiometric and polarimetric quantities. We will describe how calibration quantities are incorporated into the processor and pre-processor. We will demonstrate our techniques applied to GeoSar data and assess the stability and accuracy of the calibration. This will be compared to the modeled performance determined from calibrating the output of a point target simulator. The details of baseline determination and phase screen calculation are covered in related talks.

Chapine, Elaine↗