SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Computer program is used for analysis and design of gas turbine combustors. The program analyzes fluid flow, combustion, and heat transfer in annular and rectangular combustors with diffusers, making use of currently available analytical methods and correlations.
Model input requirements, flow charts, and program listing for launch vehicle assignment
Model input requirements, flow charts, and program listing for launch vehicle assignment
Aerodynamic forces for boundary layer profiles of flexible plate under transient motion in shear flow using computer programs
Quasi-three dimensional surface velocities and choking flow for turbomachine blade rows calculated by FORTRAN program
A digital computer program for analyzing the electromagnetic design of salient, wound pole alternators is presented. The program, which is written in FORTRAN 4, calculates the open-circuit saturation curve, the field-current requirements at rated voltage for various loads and losses, efficiency, reactances, time constants, and weights. The methods used to calculate some of these items are presented or appropriate references are cited. Instructions for using the program and typical program input and output for an alternator design are given, and an alphabetical list of most FORTRAN symbols and the complete program listing with flow charts are included.
Analytical models were developed for computing the periodic sound pressures of subsonic fans in an infinite hardwall annular duct with uniform flow. The computer programs are described which are used for numerical computations of sound pressure mode amplitudes. The data are applied to the acoustic properties of turbomachinery.
A lift/cruise exhaust deflector system for the LF336/A tip turbine lift fan was designed, built, and tested to determine the design and performance characteristics of a large-scale, single swivel nozzle thrust vectoring system. The exhaust deflector static testing was performed at the Ames Research Center outside static test stand facilities. The test hardware was installed on a hydraulic lift platform to permit both in and out of ground effect testing. The exhaust flow of the LF336/A lift fan was vectored from 0 degrees through 130 degrees during selected fan speeds to obtain performance at different operating conditions. The system was operated with and without flow vanes installed in the small radius bends to evaluate the system performance based on a proposed method of improving the internal flow losses. The program also included testing at different ground heights, to the nozzle exhaust plane, to obtain ground effect data, and the testing of two methods of thrust spoiling using a duct bypass door system and nozzle flap system.
The author has identified the following significant results. Two meteorological data acquisition systems were built to support hydrometeorological programs related to flow forecasting. Data errors were detected in the stream level formation; these errors were caused by sensor difficulties.
The APAS program a multistation structural synthesis procedure developed to evaluate material, geometry, and configuration with various design criteria usually considered for the primary structure of transport aircraft is described and evaluated. Recommendations to improve accuracy and extend the capabilities of the APAS program are given. Flow diagrams are included.
A computer simulation of a fringe type laser velocimeter has been written to determine the theoretical characteristics of the laser velocimeter when applied to a given flow field. The program includes the effect of particle size and composition on particle lag, light scattering characteristics and signal contrast. The model of the laser velocimeter includes the laser, optical system, photomultiplier, and counter type data processing electronics. The LV particle size analyzer is also modeled and incorporated in the program. An example application of the program to a Mach 5 wind tunnel using a backscatter laser velocimeter is presented.
An equation that relates the pressure flow characteristics of hydraulic spool valves was developed. The dependent variable is valve output pressure, and the independent variables are spool position and flow. This causal form of equation is preferred in applications that simulate the effects of hydraulic line dynamics. Results from this equation are compared with those from the conventional valve equation, whose dependent variable is flow. A computer program of the valve equations includes spool stops, leakage spool clearances, and dead-zone characteristics of overlap spools.
A low turbulence pressure tunnel evaluation is reported for low speed aerodynamic characteristics of the FX 66-17AII-182 airfoil as manufactured on a fiberglass sailplane. The results were compared with data for design coordinates obtained from another low turbulence wind tunnel and with theoretical calculations generated by a viscous flow airfoil computer program. The investigation was performed over a Reynolds number range, based on airfoil chord, of approximately 0.5 x 1 million to 6 million and a Mach number range of about 0.05 to 0.35. Comparison with data from another wind tunnel for the design coordinates showed slightly higher drag for the manufactured section.
The methodology to optimize the utilization of Spacelab racks and pallets and to apply this methodology to the early STS Spacelab missions was developed. A review was made of Spacelab Program requirements and flow plans, generic flow plans for racks and pallets were examined, and the principal optimization criteria and methodology were established. Interactions between schedule, inventory, and key optimization factors; schedule and cost sensitivity to optional approaches; and the development of tradeoff methodology were addressed. This methodology was then applied to early spacelab missions (1980-1982). Rack and pallet requirements and duty cycles were defined, a utilization assessment was made, and several trade studies performed involving varying degrees of Level IV integration, inventory level, and shared versus dedicated Spacelab racks and pallets.
The stoichiometric combustion of propane behind incident shock waves was studied experimentally and analytically over a temperature range from 1700 K to 2600 K and a pressure range from 1.2 to 1.9 atm. Measurements of the concentrations of carbon monoxide (CO) and carbon dioxide (CO2) and the product of the oxygen atom and carbon dioxide concentrations (O)(CO) were made after passage of the incident shock wave. A kinetic mechanism was developed which, when used in a computer program for a flowing, reacting gas behind an incident shock wave predicted experimentally measured results quite well. Ignition delay times from the literature were also predicted quite well. The kinetic mechanism consisted of 59 individual kinetic steps.
Necessary knowledge is presented on data acquisition and preparation for analysis of thermal imagery of power plant heated discharges remotely sensed from an aircraft, with special emphasis on analog to digital conversion of analog tapes acquired during scanning and to geometrical scaling. The central element in the interactive analysis of thermal imagery is an interactive graphics computer terminal which allows an interpreter to effectively interact with a large-scale computer, providing decisions or data as computations are carried out. A temperature calibration is performed, which the interpreter may test anywhere on the image. When satisfied that calibration is correct, the portion of the image to be analyzed is outlined. Printed and microfiche analyses of the plume are produced. The flow chart of programs for analysis of thermal imagery is presented and discussed in some detail.
Two computer programs determine onset flow in vicinity of horizontal tail of light aircraft.
An investigation was undertaken to determine the effectiveness of four analytical methods (empirical, modified empirical, vortex-lattice, and an inviscid, three dimensional, potential flow, wing body program) to estimate the lateral and longitudinal static stability characteristics of an isolated V-tail wind tunnel model. The experimental tests were conducted in the V/STOL tunnel at a Mach number of 0.18. Angle-of-attack data were obtained from -12 deg to 8 deg at 0 deg sideslip. Sideslip sweeps from -5 deg to 10 deg were made at angles of attack of 4 deg, 0 deg and -4 deg. The V-tail dihedral angles were 45 deg, 50 deg, 55 deg, and 60 deg.