Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pressure effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Deep Neural Network Assisted Distributed Strain and Temperature Fiber Sensor System for Natural Gas Pipeline Monitoring

Natural gas pipeline integrity monitoring is crucial to detect potential leaks, find structural issues, and prevent environmental damage. This article presents a system of natural gas pipeline monitoring that uses a specialized double Brillouin peak sensing fiber along with the Brillouin optical time domain analysis (BOTDAs) technique. The calibrated sensing fiber coefficients for strain and temperature are 41.8 kHz/ με and 0.9 MHz/°C for peak 1; and 47.2 kHz/ με , and 1.11 MHz/°C for peak 2, respectively. Initially, lab tests were performed by installing a short section of double Brillouin peak fiber (DBPF) on a 1-in steel pipe under pressure up to 1000 per square inch (psi) at elevated temperatures. Simultaneous distributed measurements of temperature and pressure-induced hoop strain were successfully measured. Considering the long processing speed to extract Brillouin frequency shift (BFS), we employ a novel probabilistic deep neural network (PDNN) framework for rapid BFS prediction. Additionally, using the Finite Element Method, the effects of the pipeline pressure on hoop strain were modeled and compared to the experimental hoop strain under the same set of pipeline conditions. Finally, an actual 4-in outer diameter steel natural gas pipeline was used for pilot-scale tests, where hoop strain was measured at various pressure levels. Leaks were simulated to demonstrate accurate pipeline integrity monitoring. At an internal pipe pressure of 1000 psi, hoop strain of approximately 300 με was observed, and the sensitivity was calculated as 0.28 με /psi. The results of this pilot-scale study demonstrated that the system is capable of performing distributed monitoring sufficient to detect pipeline pressure and the presence of leaks to ensure the safe operation of gas pipelines in the field.

03 NATURAL GAS↗
DOE OSTI2023

Computational Analysis of the Impact of Boundary Conditions on a Particle-Laden Flow: A Case Study in a Pressurized Oxy-Coal Combustor

Designing an effective burner is vital for the development of coal combustion technologies. Because of high pressure, the volumetric fraction of the coal particles in the injected fuel in a pressurized oxy-combustion (POC) burner approaches or even exceeds the limitations allowed by the commercial computational fluid dynamics codes (e.g., Ansys Fluent). Consequently, for such high particle volumetric fractions, the interplay between the particles, the fluid flow, and the burner wall needs to be re-evaluated. The present computational work is a first step in a systematic analysis of the roles of various characteristics involved in the POC process, such as the method of particle release, its location, and the particle size. Specifically, pulverized coal is burned under an elevated pressure of 15 bar in an O 2 /CO 2 environment. A 100 kW, a POC combustor, is modeled with Ansys Fluent using the Reynolds-averaged Navier−Stokes approach. It is revealed that for this pilot-scale, pressurized burner, the gas phase flow velocity in the near-wall region exhibits anomalies. With the major focus on POC, this work aims to eliminate/reduce the impact of high particle loading on the gas-phase flow. To scrutinize the role of particle loading in the near-wall region and eliminate the impact of this velocity on POC downstream, the particle−gas interplay in the boundary layer is investigated by means of the computational simulations incorporating the coupling between the turbulent flow and the particles. It is found that the tuning of the particle release location makes the gas-phase flow velocity in the presence of particles consistent with the pure gas flow velocity profile. The particles size is also found to have a significant impact on the particle trajectory.

CFD↗
DOE OSTI2021

Conduction Heat Transfer through Solid in Porous Materials: A Comparative Study by Finite-Element Simulations and Effective Medium Approximations

The development of insulation materials with low effective thermal conductivity is essential for energy savings in various applications, including buildings, food services, pipe insulation, and refrigeration. Such materials can be developed by using micro- or nanoporous structures, as well as low-thermal conductivity gases and/or reduced pressure. A variety of effective medium approximation (EMA) models have been developed to study thermal transport through solid in porous structures. However, in many cases, the impacts of porosity on solid conduction are not well predicted by EMA models because of the assumptions made for simplification. Furthermore, the results can vary by a factor of up to 1.5, depending on the morphology of the pores. Hence, proper guidance is needed to choose the appropriate EMA model for a given morphology. This work presents a finite element method study using COMSOL Multiphysics software for various geometries, including hollow cubes, overlapping hollow spheres (normally stacked and tightly packed), and Voronoi structures, and compares the results to those obtained from various EMA models. Simulation results for the hollow cubes and Voronoi structures matched well with the Maxwell-Eucken and Russell model. The results for hollow spheres closely matched the Bauer model and the Glicksman model with fitting parameters. This work provides guidance on analyzing and designing insulation materials for energy savings in the future.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Synthesis of Yttrium Superhydride Superconductor with a Transition Temperature up to 262 K by Catalytic Hydrogenation at High Pressures

The recent observation of room-temperature superconductivity will undoubtedly lead to a surge in the discovery of new, dense, hydrogen-rich materials. The rare earth metal superhydrides are predicted to have very high-T c superconductivity that is tunable with changes in stoichiometry or doping. Here we report the synthesis of an yttrium superhydride that exhibits superconductivity at a critical temperature of 262 K at 182±8 GPa. A palladium thin film assists the synthesis by protecting the sputtered yttrium from oxidation and promoting subsequent hydrogenation. Phonon-mediated superconductivity is established by the observation of zero resistance, an isotope effect and the reduction of T c under an external magnetic field. Furthermore, the upper critical magnetic field is 103 T at zero temperature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Analytic model of the remobilization of pinned glide dislocations: Including dislocation drag from phonon wind

Here, we discuss the effect of a non-constant dislocation drag coefficient on the very high strain rate regime within an analytic model describing mobile-immobile dislocation intersections applicable to fcc polycrystals. Based on previous work on dislocation drag, we estimate its temperature and pressure dependence and its effects on stress–strain rate relations. In the high temperature regime, we show that drag can remain the dominating effect even down to intermediate strain rates. We also discuss the consequences of having a limiting dislocation velocity, a feature which is typically predicted by analytic models of dislocation drag, but which is somewhat under debate because a number of MD simulations predict supersonic dislocations.

42 ENGINEERING↗
DOE OSTI2022

Thermal conductivity tensor of γ and ε -hexanitrohexaazaisowurtzitane as a function of pressure and temperature

Using reverse non-equilibrium molecular dynamics simulations, we have determined the dependences on temperature and pressure of the thermal conductivity tensors for the monoclinic γ and ε polymorphs of hexanitrohexaazaisowurtzitane (HNIW or CL20). In this work, a recently developed non-reactive force field [X. Bidault and S. Chaudhuri, RSC Adv. 9, 39649–39661 (2019)], designed to study polymorphism and phase transitions in CL20, is employed. The effects of temperature and pressure are investigated between 200 and 500 K and up to 0.5 GPa for γ-CL20 and 2 GPa for ε-CL20. In order to obtain the full thermal conductivity tensor, $κ_{ij}$, for the monoclinic crystals, four distinct heat propagation directions are used. We find that $κ_{ij}$ for both polymorphs is more isotropic than for other energetic molecular crystals, including α- and γ-RDX, β-HMX, and PETN, with a maximum difference of 9.8% between orientations observed at 300 K and 0 GPa for γ-CL20 and a maximum difference of 4.8% for ε-CL20. The average thermal conductivity, $\bar{κ}$, of ε-CL20 is 6.4% larger than that of γ-CL20 at 300 K and 0 GPa. Analytic linear functions of the inverse temperature and the pressure are provided, which fit the data well and can be used to predict the thermal conductivity of both polymorphs for any orientation, pressure, and temperature in and around the fitting range. Our predictions agree reasonably well with the limited available experimental data, for which the polymorph type is unknown.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Isotope effect and critical magnetic fields of superconducting YH 6 : A Migdal-Eliashberg theory approach

The emergence of near-ambient temperature superconductivity under pressure in metal hydride systems has motivated a desire to further understand such remarkable properties, specifically critical magnetic fields. Here, YH 6 is suggested to be a departure from conventional superconductivity, due to apparent anomalous behavior. Using density functional calculations in conjunction with Migdal-Eliashberg theory we show that in YH 6 the critical temperature and the isotope effect under pressure, as well as the high critical fields, are consistent with strong-coupling conventional superconductivity, a property anticipated to extend to other related systems. Furthermore, strong-coupling corrections occur to the expected BCS values for the isotope effect coefficient (α), Ginzburg-Landau parameter [κ 1 ⁡(T)], London penetration depth [λ L (T)], electromagnetic coherence length [ξ⁡(T)], and the energy gap (Δ 0 ).

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Fuel Stratification Effects on Gasoline Compression Ignition with a Regular-Grade Gasoline on a Single-Cylinder Medium-Duty Diesel Engine at Low Load

Prior research studies have investigated a wide variety of gasoline compression ignition (GCI) injection strategies and the resulting fuel stratification levels to maintain control over the combustion phasing, duration, and heat release rate. Previous GCI research at the US Department of Energy’s Oak Ridge National Laboratory has shown that for a combustion mode with a low degree of fuel stratification, called “partial fuel stratification” (PFS), gasoline range fuels with anti-knock index values in the range of regular-grade gasoline (~87 anti-knock index or higher) provides very little controllability over the timing of combustion without significant boost pressures. On the contrary, heavy fuel stratification (HFS) provides control over combustion phasing but has challenges achieving low temperature combustion operation, which has the benefits of low NOX and soot emissions, because of the air handling burdens associated with the required high exhaust gas recirculation rates. Furthermore, this work investigates HFS and PFS combustion, efficiency, and emissions performance on a single-cylinder, medium-duty engine with a regular-grade gasoline (91 research octane number) at 1,200 rpm, 4.3 bar, and 3.0 nominal gross indicated mean effective pressure operating points with boost levels similar to those in a medium-duty diesel application. Authority of combustion phasing with main injection timing sweeps for HFS and second injection timing sweeps and fuel split sweeps for PFS are shown. In addition, this work is discussed in the context of previous findings with a light-duty diesel platform, and next steps and future direction for this work are presented.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Rheology characterization of ionic liquids under high pressure and high temperature

Ionic liquids (ILs) are liquid salts that exist at or below ambient temperatures and are composed of ion pairs. They offer promising alternatives to toxic, hazardous, highly flammable, and volatile solvents in various applications such as solution preparation, dispersion, gel formation, composites, and polymer melts. ILs possess unique and interesting characteristics, including excellent chemical and thermal stability and low vapor pressures. Understanding the rheological properties of ILs is essential to optimizing IL performance. This paper presents a comparative analysis of the rheological properties of two ionic liquids, Nsingle bondHexylpyridinium tetrafluoroborate (HPyBF4) and Nsingle bondHexylpyridinium bromide (HPyBr), under different shear rates, temperatures, and pressures. Rheological measurements were performed under varying controlled pressure and temperature conditions. The experimental investigation covered a pressure range of 689–12,411 kPa [100–1800 psi] and a temperature range from room temperature up to 522 kelvin (K) [480°F]. The primary objective is to explore and compare the flow behavior and viscoelastic characteristics of HPyBF4 and HPyBr under high-pressure and high-temperature conditions. The experimental data showed that HPyBF4 and HPyBr exhibited shear-thinning behavior, and pressure had an insignificant effect on rheology compared to the temperature effect. Under the same testing conditions, HPyBr showed higher shear stress and viscosity than HPyBF4. This research significantly contributes to the improved understanding of the rheological behavior of these specific ionic liquids and their suitability for diverse industrial and scientific applications, particularly in high-pressure and high-temperature environments.

15 GEOTHERMAL ENERGY↗
DOE OSTI2022

Hybrid time–frequency domain dual-probe coherent anti-Stokes Raman scattering for simultaneous temperature and pressure measurements in compressible flows via spectral fitting

We demonstrate a hybrid time–frequency spectroscopic method for simultaneous temperature/pressure measurements in nonreacting compressible flows with known gas composition. Hybrid femtosecond–picosecond, pure-rotational coherent anti-Stokes Raman scattering (CARS), with two independent, time-delayed probe pulses, is deployed for single-laser-shot measurements of temperature and pressure profiles along an ∼ <#comment/> 5 -mm line. The theory of dual-probe CARS is presented, along with a discussion of the iterative fitting of experimental spectra. Temperature is obtained from spectra acquired with an early, near-collision-free probe time delay ( τ <#comment/> 1 = 0 p s ) and pressure from spectra obtained at probe delays of τ <#comment/> 2 = 150 − <#comment/> 1000 p s , where collisions significantly impact the spectral profile. Unique solutions for temperature and pressure are obtained by iteratively fitting the two spectra to account for small collisional effects observed for the near zero probe delay spectrum. A dual-probe pure-rotational CARS system, in a 1D line-imaging configuration, is developed to demonstrate effectively the simultaneous temperature and pressure profiles recorded along the axial centerline of a highly underexpanded jet. The underexpanded air jet permits evaluation of this hybrid time–frequency domain approach for temperature and pressure measurements across a wide range of low-temperature–low-pressure conditions of interest in supersonic ground-test facilities. Single-laser-shot measurement precisions in both quantities and pressure measurement accuracy are systematically evaluated in the quiet zone upstream of the Mach disk. Precise thermometry approaching 1%−2% is observed in regions of high CARS signal-to-noise ratios. Pressure measurements are optimized at probe time delays where the ratio of the late probe delay to the Raman lifetime exceeds four ( τ <#comment/> 2 / τ <#comment/> R > <#comment/> 4 ). The impact of low-temperature Raman linewidths on CARS pressure measurements is evaluated, and comparisons of CARS pressures obtained with our recent low-temperature pure-rotational Raman linewidth data and extrapolated high-temperature Q -branch linewidths are presented. Considering all measurements with τ <#comment/> 2 / τ <#comment/> R ≥ <#comment/> 4.0 , measured pressures were on average 7.9% of the computed isentropic values with average shot-to-shot deviations representing a combination of instrument noise and fluid fluctuations of 5.0%.

Retter, Jonathan E.↗
DOE OSTI2023

Access and Capture of Layered Double Perovskite Polytypic Phase through High-Pressure Engineering

Engineering halide perovskites through external pressure is as an effective means to tune the crystal structure, thus optoelectronic properties of the material. In this work, we studied the structural and optical property evolutions of Cs 4 M II Bi 2 Cl 12 (M II : Cd, Cd 0.8 Mn 0.2 , Mn) layered double perovskite (LDP) crystalline powders under high pressure. A novel polytypic phase transition was observed featuring lateral interlayer sliding of the Bi–M II –Bi trilayer units, resulting in a new LDP-12R phase. Importantly, this high-pressure induced LDP-12R crystal phase can be preserved after complete decompression and captured at ambient conditions. Moreover, the LDP samples showed a pressure-dependent photoluminescence property. Finally, our findings exemplified a new perovskite polytype that can be accessed and captured through high-pressure processing, advocating the uniqueness of LDP materials with soft and transformable crystal lattices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Temperature- and Rate-Dependent Pathways in Formation of Metastable Silicon Phases under Rapid Decompression

High-pressure metallic beta-Sn silicon (Si-II), depending on temperature, decompression rate, stress, etc., may transform to diverse metastable forms with promising semiconducting properties under decompression. However, the underlying mechanisms governing the different transformation paths are not well understood. Here, two distinctive pathways, viz., a thermally activated crystal-crystal transition and a mechanically driven amorphization, were characterized under rapid decompression of Si-II at various temperatures using in situ time-resolved x-ray diffraction. Under slow decompression, Si-II transforms to a crystalline bc8/r8 phase in the pressure range of 4.3-9.2 GPa through a thermally activated process where the overdepressurization and the onset transition strain are strongly dependent on decompression rate and temperature. In comparison, Si-II collapses structurally to an amorphous form at around 4.3 GPa when the volume expansion approaches a critical strain via rapid decompression beyond a threshold rate. The occurrence of the critical strain indicates a limit of the structural metastability of Si-II, which separates the thermally activated and mechanically driven transition processes. The results show the coupled effect of decompression rate, activation barrier, and thermal energy on the adopted transformation paths, providing atomistic insight into the competition between equilibrium and nonequilibrium pathways and the resulting metastable phases.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Flexible MOFs as Pressure-Tunable Filters for Hydrocarbon Separation

Metal–organic frameworks (MOFs) hold significant promise for separating gas mixtures, especially hydrocarbons. While the main focus in the field is the development of new adsorbents for specific separations of binary mixtures, a preferable situation would be using a single framework for separating various species. This has been achieved in some flexible MOFs, where ternary mixtures can be separated at different temperatures. Here, we propose a simple yet fascinating way of utilizing the flexibility of MOFs to create tunable filters as a function of external pressure. We thus replace the more costly temperature-driven tunability with a cost-efficient external-pressure tunability. As a proof-of-concept, we select the CaMOF flexible framework for C6 hydrocarbon separation, however, our results are applicable to other flexible framework and gas molecules. Furthermore, our findings provide mechanistic insight and guidelines to engineer separation filters by designing flexible pores with critical sizes that can be effectively manipulated by external pressure.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A Gradual Decline of Star Formation since Cluster Infall: New Kinematic Insights into Environmental Quenching at 0.3 < z < 1.1

The environments where galaxies reside crucially shape their star formation histories. We investigate a large sample of 1626 cluster galaxies located within 105 galaxy clusters spanning a large range in redshift (0.26 < z < 1.13). The galaxy clusters are massive (M 500 ≳ 2 × 10 14 M ⊙ ) and uniformly selected from the SPT and ACT Sunyaev–Zel'dovich surveys. With spectra in hand for thousands of cluster members, we use the galaxies' position in projected phase space as a proxy for their infall times, which provides a more robust measurement of environment than quantities such as projected clustercentric radius. We find clear evidence for a gradual age increase of the galaxy's mean stellar populations (~0.71 ± 0.4 Gyr based on a 4000 Å break, D n 4000) with the time spent in the cluster environment. This environmental quenching effect is found regardless of galaxy luminosity (faint or bright) and redshift (low or high-z), although the exact stellar age of galaxies depends on both parameters at fixed environmental effects. Such a systematic increase of D n 4000 with infall proxy would suggest that galaxies that were accreted into hosts earlier were quenched earlier due to longer exposure to environmental effects such as ram pressure stripping and starvation. Compared to the typical dynamical timescales of 1–3 Gyr of cluster galaxies, the relatively small age increase (~0.71 ± 0.4 Gyr) found in our sample galaxies seems to suggest that a slow environmental process such as starvation is the dominant quenching pathway. Our results provide new insights into environmental quenching effects spanning a large range in cosmic time (~5.2 Gyr, z = 0.26–1.13) and demonstrate the power of using a kinematically derived infall time proxy.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2024

Lightweight single-phase Al-based complex concentrated alloy with high specific strength

Developing light yet strong aluminum (Al)-based alloys has been attracting unremitting efforts due to the soaring demand for energy-efficient structural materials. However, this endeavor is impeded by the limited solubility of other lighter components in Al. Here, we propose to surmount this challenge by converting multiple brittle phases into a ductile solid solution in Al-based complex concentrated alloys (CCA) by applying high pressure and temperature. We successfully develop a face-centered cubic single-phase Al-based CCA, Al 55 Mg 35 Li 5 Zn 5 , with a low density of 2.40 g/cm 3 and a high specific yield strength of 344×10 3 N·m/kg (typically ~ 200×10 3 N·m/kg in conventional Al-based alloys). Our analysis reveals that formation of the single-phase CCA can be attributed to the decreased difference in atomic size and electronegativity between the solute elements and Al under high pressure, as well as the synergistic high entropy effect caused by high temperature and high pressure. The increase in strength originates mainly from high solid solution and nanoscale chemical fluctuations. Our findings could offer a viable route to explore lightweight single-phase CCAs in a vast composition-temperature-pressure space with enhanced mechanical properties.

42 ENGINEERING↗
DOE OSTI2020

In-situ Detection of Glovebox Glove Degradation Prior to Glove Failure; Effects on Safety, Waste, and Operational Costs - 20402

Glovebox glove pressure decay leak testing and analysis of the data can greatly improve glovebox safety, minimize Transuranic (TRU) glove waste, and minimize operational cost. It is well known, the weakest point of containment on a glovebox is the glove. Mitigating unplanned openings in gloves is critical to minimizing operational and safety costs in glovebox operations. Mitigating unplanned glove openings due to glove failures will be discussed in this paper. The lack of an engineered solution to determine a gloves operational life in nuclear operations, has lead to use of theoretical and manual subjective methods to determine the life and safety of a glovebox glove. Whether the glove is inspected visually prior to use, or gloves are changed regularly to theoretically avoid failure, both the operators PPE and the room are being exposed to contamination, or un-necessary amounts of TRU glove waste are being generated. Millions of dollars yearly in operational costs are spent on glove failures due to loss of production, incident analysis, regulatory audits, clean up, and paperwork. In a nuclear application, a glove failure could contaminate an operator and laboratory, shut down the operation for weeks, potentially create a regulatory audit, and potentially create a media frenzy; the damages to the organization can be astronomical. Elimination of glove failures is possible by tracking glove material degradation and setting limits to allow glove change when it becomes necessary, prior to glove failure. Analytical pressure decay leak testing allows the detection of material degradation, and in turn the ability to limit operational glove failures. A German based company called MK Versuchsanlagen, e.K., has developed an advanced Glove Integrity Testing System. The system, with its use of proprietary RFID and special software technology, is unique in its capabilities. The system is capable to perform highly accurate regular glove testing on any size glovebox line in minimal time. The system records and can analyze a tremendous amount of system data that in turn can determine, for example, a safe glove change time prior to a glove material failure. This paper will show how an advanced Glove Integrity Testing System can detect glove material degradation and help determine a safe change point prior to glove failure. Pressure decay curves of new gloves and recorded effects of accelerated aging on the glove over time will be shown. The use of this technology in nuclear facilities can greatly improve glovebox operational safety, minimize glovebox glove TRU waste, and save organizations tremendous costs in downtime, clean up, documentation, and potential regulatory review. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Implementation and testing of physics-based pulverization model in BISON

This report summarizes lower length scale computational research conducted to improve the pulverization criterion for high-burnup UO 2 fuel in the BISON fuel performance code. This research was sponsored by the NEAMS program during FY22. Efforts to improve the model primarily focus on calculating the current pressure of bubbles in the high-burnup structure (HBS) region, as well as the critical bubble pressure at which pulverization occurs in the HBS. The phase-field model for predicting initial bubble pressure in the HBS was improved by implementing a more realistic model for defect production, and by coupling the phase-field model for inter-granular bubble evolution with the spatially-resolved cluster dynamics code Xolotl to simulate intra-granular fission gas evolution. An evolution equation for current bubble pressure was added to BISON, an improvement over the previous model that assumed that bubble pressure was static following HBS formation. To improve calculations of critical bubble pressure for pulverization, 3-D phase-field fracture simulations were performed, and a function for critical bubble pressure was fit—based on the simulation results—to replace the previous function, which had been determined using 2-D simulations. The impacts of these modifications to the existing pulverization assessment cases will be reported in the forthcoming engineering scale milestone on high-burnup UO 2 pulverization. A poromechanics-based approach was used to include the effect of bubble over pressurization on the stress state of the pellet at the engineering scale, and the initial strategy for integration of the pulverization criterion with pellet-scale mechanical degradation using a smeared cracking model was developed. This report also describes the initial research that was conducted to inform a forthcoming transient fission gas release (tFGR) model in BISON. Focusing on the fission gas release caused by pulverization of the outer pellet rim, a model for the amount of fission gas release was developed as a function of fuel porosity, bubble size, and fragment size. Implementation of this model in BISON and its impact of engineering-scale predictions will also be described in the aforementioned engineering-scale milestone on high-burnup UO 2 pulverization.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Verification of Coupled Hydraulic Fracturing Simulators Using Laboratory-Scale Experiments

In this work, we aim to verify the predictions of the numerical simulators, which are used for designing field-scale hydraulic stimulation experiments. Although a strong theoretical understanding of this process has been gained over the past few decades, numerical predictions of fracture propagation in low-permeability rocks still remains a challenge. Against this background, we performed controlled laboratory-scale hydraulic fracturing experiments in granite samples, which not only provides high-quality experimental data but also a well-characterized experimental set-up. Using the experimental pressure responses and the final fracture sizes as benchmark, we compared the numerical predictions of two coupled hydraulic fracturing simulators—CSMP and GEOS. Both the simulators reproduced the experimental pressure behavior by implementing the physics of Linear Elastic Fracture Mechanics (LEFM) and lubrication theory within a reasonable degree of accuracy. The simulation results indicate that even in the very low-porosity (1–2 %) and low-permeability (10 -18 m 2 - 10 -19 m 2 ) crystalline rocks, which are usually the target of EGS, fluid-loss into the matrix and unsaturated flow impacts the formation breakdown pressure and the post-breakdown pressure trends. Therefore, underestimation of such parameters in numerical modeling can lead to significant underestimation of breakdown pressure. The simulation results also indicate the importance of implementing wellbore solvers for considering the effect of system compressibility and pressure drop due to friction in the injection line. The varying injection rate as a result of decompression at the instant of fracture initiation affects the fracture size, while the entry friction at the connection between the well and the initial notch may cause an increase in the measured breakdown pressure.

15 GEOTHERMAL ENERGY↗