SEARCH · Engineering Papers

Results for “Predictive Data analytics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

All sources NASA NTRS DOE OSTI

NASA NTRS1980

Block 4 receiver tracking loop performance in the presence of a CW RFI

A model that allows one to predict the tracking performance of the Block 4 receiver in the presence of a continuous wave radio frequency interference is discussed. Experimental and analytical results are provided for a typical Deep Space Network operational mode. Simulation and experimental results show good agreement with theoretical prediction for the static phase error and out-of-lock values. Predicted phase jitter is consistently lower than the experimental and simulated results by a factor of one-half for small interference to signal ratio (ISR) when the offset frequency is small. For large ISR, good agreement is observed. The analytical model assumes a noiseless condition, which is valid only when the loop is operated at strong signal levels. Experimental data indicate, however, that even at the minimum operating signal level of 10-dB carrier margin, reasonably good prediction can still be obtained. A curve of protection criteria that extends the current recommendation is also presented.

Sue, M. K.↗

NASA NTRS1987

Performance and aerodynamic braking of a horizontal-axis wind turbine from small-scale wind tunnel tests

Wind tunnel tests of three 20" diameter, zero twist, zero pitch wind turbine rotor models were conducted in a 7' x 10' wind tunnel to determine the performance of such rotors with NACA 23024 and NACA 64 sub 3-621 airfoil sections. Aerodynamic braking characteristics of a 38% span, 30% chord, vented aileron configuration were measured on the NACA 23024 rotor. Surface flow patterns were observed using fluorescent mini-tufts attached to the suction side of the rotor blades. Experimental results with and without ailerons are compared to predictions using airfoil section data and a momentum performance code. Results of the performance studies show that the 64 sub 3-621 rotor produces higher peak power than the 23024 rotor for a given rotor speed. Analytical studies, however, indicate that the 23024 should produce higher power. Transition strip experiments show that the 23024 rotor is much more sensitive to roughness than the 64 sub 3-621 rotor. These trends agree with analytical predictions. Results of the aileron test show that this aileron, when deflected, produces a braking torque at all tip speed ratios. In free wheeling coastdowns the rotor blade stopped, then rotated backward at a tip speed ratio of -0.6.

Cao, H. V.↗

NASA NTRS1975

Turbulent pressure field in a co-annular jet

Single point and two-point fluctuating static pressure measurements have been made in the initial mixing and transition regions in a co-annular circular jet. Space scales, correlation and time scales in the convected frame, and convection velocities have been determined for both broad band and narrow band frequency components. Analytical functionals describing the structural behavior of the turbulent pressure field have been developed from the data which are suitable for direct application in predicting the sound power level radiated from this turbulent field. Effects of both area and velocity ratios are incorporated in the model.

Hammersley, R. J.↗

NASA NTRS1976

Inlet spillage drag tests and numerical flow-field analysis at subsonic and transonic speeds of a 1/8-scale, two-dimensional, external-compression, variable-geometry, supersonic inlet configuration

Accurate spillage drag and pressure data are presented for a realistic supersonic inlet configuration. Results are compared with predictions from a finite-differencing, inviscid analysis computer procedure. The analytical technique shows good promise for the evaluation of inlet drag, but necessary refinements were identified. A detailed description of the analytical procedure is contained in the Appendix.

Hawkins, J. E.↗

NASA NTRS1990

Adaptive structures in space

Future NASA missions will need large (20 to 100m) structural systems with precision position (few microns to submicron) requirements. Data are presented which indicate the technology deficiencies of previous programs and analyses in current state-of-the-art structural design approaches, analytical prediction capabilities, control of structure capabilities, and ground test technologies to meet the performance requirements of future large precision structural systems. Test results on laboratory truss structures that demonstrate static displacement control, active damping, and on-orbit system identification are described. It is shown that for large precision structures, adaptive structures provide not only a means to achieve the precision and characteristics required in space, but can also significantly alleviate the ground test requirements for flight-validating the hardware.

Wada, B. K.↗

NASA NTRS1992

Modeling and simulation of mobile satellite propagation

Mobile satellite systems are subject to severe fading due to blockage of the line-of-sight (LOS) path by roadside vegetation. A thorough understanding of the fading effects is necessary for the design of a reliable land mobile satellite system (LMSS). Analytical and empirical models are presented for predicting fade statistics for vegetative shadowing of mobile satellite terminals. A software simulator for generating simulated fade data is also presented. A physical model relating physical path parameters to propagation model parameters is presented, and results using the model are shown.

Barts, R. M.↗

NASA NTRS1993

Antenna pattern control using impedance surfaces

During the period of this research project, a comprehensive study of pyramidal horn antennas was conducted. Full-wave analytical and numerical techniques were developed to analyze horn antennas with or without impedance surfaces. Based on these full-wave analytic techniques, research was conducted on the use of impedance surfaces on the walls of the horn antennas to control the antenna radiation patterns without a substantial loss of antenna gain. It was found that the use of impedance surfaces could modify the antenna radiation patterns. In addition to the analytical and numerical models, experimental models were also constructed and they were used to validate the predictions. Excellent agreement between theoretical predictions and the measured data was obtained for pyramidal horns with perfectly conducting surfaces. Very good comparisons between numerical and experimental models were also obtained for horns with impedance surfaces.

Balanis, Constantine A.↗

NASA NTRS2002

Broadband Noise Predictions Based on a New Aeroacoustic Formulation

A new analytic result in acoustics called 'Formulation 1B,' proposed by Farassat, is used to compute the loading noise from an unsteady surface pressure distribution on a thin airfoil in the time domain. This formulation is a new solution of the Ffowcs Williams-Hawkings equation with the loading source term. The formulation contains a far-field surface integral that depends on the time derivative and the surface gradient of the pressure on the airfoil, as well as a contour integral on the boundary of the airfoil surface. As a first test case, the new formulation is used to compute the noise radiated from a flat plate, moving through a sinusoidal gust of constant frequency. The unsteady surface pressure for this test case is specified analytically from a result that is based on linear airfoil theory. This test case is used to examine the velocity scaling properties of Formulation 1B, and to demonstrate its equivalence to Formulation 1A, of Farassat. The new acoustic formulation, again with an analytic surface pressure, is then used to predict broadband noise radiated from an airfoil immersed in homogeneous turbulence. The results are compared with experimental data previously reported by Paterson and Amiet. Good agreement between predictions and measurements is obtained. The predicted results also agree very well with those of Paterson and Amiet, who used a frequency-domain approach. Finally, an alternative form of Formulation 1B is described for statistical analysis of broadband noise.

Casper, J.↗

NASA NTRS2003

Spray Bar Zero-Gravity Vent System for On-Orbit Liquid Hydrogen Storage

During zero-gravity orbital cryogenic propulsion operations, a thermodynamic vent system (TVS) concept is expected to maintain tank pressure control without propellant resettling. In this case, a longitudinal spray bar mixer system, coupled with a Joule-Thompson (J-T) valve and heat exchanger, was evaluated in a series of TVS tests using the 18 cu m multipurpose hydrogen test bed. Tests performed at fill levels of 90, 50, and 25 percent, coupled with heat tank leaks of about 20 and 50 W, successfully demonstrated tank pressure control within a 7-kPa band. Based on limited testing, the presence of helium constrained the energy exchange between the gaseous and liquid hydrogen (LH2) during the mixing cycles. A transient analytical model, formulated to characterize TVS performance, was used to correlate the test data. During self-pressurization cycles following tank lockup, the model predicted faster pressure rise rates than were measured; however, once the system entered the cyclic self-pressurization/mixing/venting operational mode, the modeled and measured data were quite similar. During a special test at the 25-percent fill level, the J-T valve was allowed to remain open and successfully reduced the bulk LH2 saturation pressure from 133 to 70 kPa in 188 min.

Hastings, L. J.↗

NASA NTRS2019

Examination of Annular-Electrode Spark Discharges in Flowing Oxygen – Experimental Nuances

Microsecond sparks and the resulting plume of hot gas/plasma were examined against a parametric pressure-distance matrix. Schlieren imaging is used to capture the spatial and temporal location of spark discharge exhaust for two milliseconds. Low pressure and larger gap widths created the largest size and intensity signal for the spark-affected plumes. Experimental exit-plume velocities trend well with analytic predictions using a mean pressure between the chamber and atmospheric conditions. Due to the quadratic relation of the annulus area and gap width, larger gap width velocities are more accurately represented by analytic predictions using atmospheric pressure as the larger exit area restricts the flow less. The same pressure adjustment, when applied to breakdown voltages, improves data alignment with Paschen’s Curve.

Darren C Tinker↗

NASA NTRS1981

On the OLP prediction of the unstable modes of the flat plate turbulent boundary layer

The Orr et al. (OLP) stability analysis is reformulated to yield profiles from hot-wire velocity covariance data in the boundary layer of a flow over a flat plate. The proper orthogonal decomposition theorem (PODT) is used to maximize the mean square of the inner product of the velocity vector with a deterministic candidate vector function in Hilbert space. The OLP formulation couples the PODT for the eddy viscosity with a global extremum principle for the disturbance kinetic energy. Derivation of the governing equations is described analytically, as are the extraction of the mean velocity profile and the eddy viscosity. Finally, techniques for characterizing the dominant mode of the velocity field are introduced and applied to three-dimensional flow over a flat plate. Good agreement is found between the predictions, using laboratory data, and the measured energy and three-dimensional structures of the dominant eddies.

Wadia, A. R.↗

NASA NTRS1983

Thermochemical response of honeycomb sandwich panels

A simple study aimed at predicting the thermochemical response of honeycomb sandwich panels is presented. The overall thermal conductivity coefficient for the panel is obtained through a consideration of the convective gas movement within the cell spaces. The earlier correlations of Catton and Edwards are used. The analytical solution for the one-dimensional approximation is quoted from an earlier study. In comparison with three data points obtained at JPL at heat fluxes of 2.5, 5 and 8 W/sq cm, the char penetration depth is well predicted, especially when the debonding of the face sheet is considered. Re-radiation of incident heat flux from the debonded face sheet plays an important role in this model.

Ramohalli, K.↗

NASA NTRSDate not supplied

Inlet Radiated Noise Predictions for the NASA Source Diagnostic Test Fan Using Physics-Based Simulations

Commercial supersonic aircraft are expected to produce considerably more noise during landing and take-off operations than existing subsonic aircraft. Establishing noise regulation is challenging because no examples of this aircraft type are currently flying. Existing aircraft noise prediction tools can be used, but the noise source models for these empirical tools are typically based on data from subsonic aircraft components. The present work documents a procedure for using physics-based computational tools to generate the propagating sound field radiating out the nacelle inlet. Although no analytical source modeling is demonstrated, these tools utilize measured data to compare the complex pressure for various propagating modes. The discrepancies found in applying the propagation tools to the subsonic inlet will be ascribed to calculations of supersonic inlets being used to update current empirical noise prediction tools.

Noise Predictions↗

NASA NTRSDate not supplied

How the Open Data Policy of the Landsat Program Has Advanced Our Understanding of Environmental Change

A time series is a sequence of observations of a phenomenon taken sequentially in time. A crucial characteristic of a time series is the dependence among adjacent observations – techniques for analyzing this dependence are referred to as time series analysis. This analytical approach enables us to predict or forecast future values of a time series, study the impact of various inputs on the observed phenomenon, and examine interrelationships among related time series variables. Within the geographical sciences, time series analysis has historically been limited to coarse-resolution satellite data, as constructing time series of data suitable for studying land cover and land use dynamics, such as Landsat data, were prohibitively costly. A transformative shift occurred in 2008 when the U.S. Government decided to make free and open all past and future data collected by the Landsat satellite program. The decision brought about a paradigm shift away from analyzing individual images or observations to continuous monitoring in time. Of particular relevance to environmental remote sensing is the ability to forecast observations – if we can predict how future observations should behave, we can infer information about how the land surface is changing. In this presentation, we will examine literature examples that showcase scientific gains enabled by time series analysis of satellite data. We will delve into how the analysis of dense time series of satellite data revealed that overall rate of forest disturbance in the Amazon has increased despite a reduction in deforestation; how different types of forest degradation, previously unquantified, are now being accurately assessed in the Caucasus region; and how we now can study the highly dynamic and intricate patterns of shifting cultivation in Southeast Asia.

Pontus Olofsson↗

NASA NTRS1988

Failure of compression-loaded multi-directional composite laminates

An analytical and experimental investigation of the failure of selected compression-loaded composite laminates is described. A general nonlinear theory is presented for predicting a laminate's compressive strength and failure mode. The theory includes the effects of out-of-plane ply waviness, inplane fiber waviness, and fiber scissoring. A simple compressive test technique is used to obtain the experimental data. The analytical and experimental results show good agreement for theta less than 45 deg and show excellent agreement for theta not less than 45 deg. The dominant compression failure modes for the laminates in this study were found to be interlaminar shearing, inplane matrix shearing, and matrix compression.

Shuart, Mark J.↗

NASA NTRS2020

Sub-Mesoscales at Ocean Fronts: Dissipation of Eddy Kinetic Energy

D’Asaro et al. measured the dissipation of eddy kinetic energy at the Kuroshio ocean front, found it to be 1-2 orders of magnitude larger than the value predicted by the law of the wall and suggested that the enhancement is due to sub-mesoscales, SM. To assess their suggestion, we employ two SM models. In the first model the buoyancy flux is based on baroclinic instabilities only and there is no momentum flux (Reynolds stresses). The model is unable to reproduce the Kuroshio data. The second model includes baroclinic instabilities, wind stress and Reynolds stresses. It reproduces the data satisfactorily. The analytic formula for the dissipation that we present can be used in OGCMs to parameterize dissipation at ocean fronts other than Kuroshio, e.g., Gulf Stream and ACC, an extension that could improve the predictions of climate studies.

sub-mesoscale models↗

NASA NTRS1985

Implementation and verification of a comprehensive helicopter coupled rotor - Fuselage analysis

The analytical basis and the application of a Rotor/Airframe Comprehensive Aeroelastic Program (RACAP) are described in detail. The rationale behind each analytical choice is outlined and the modular procedure is described. The program is verified by application to the AH-1G helicopter. The applicability of various airload prediction models is examined, and both the steady and vibratory responses of the blade are compared with flight test data. Reasonable correlation is found between measured and calculated blade response, with excellent correlation for vibration amplitudes at various locations on the fuselage such as engine, pilot seat, and gunner. Within the analytical model, comparisons are drawn between an isolated blade analysis and a coupled rotor/fuselage model. The deficiency of the former in the context of the AH-1G is highlighted.

Wood, E. R.↗

NASA NTRS1982

Fatigue and fracture research in metals

Fatigue and fracture research on monolithic and laminated metals is discussed. The research concentrated on three areas: stress analyses of two and three dimensional cracked bodies, fatigue crack growth, and fracture toughness. Analytical methods were developed to predict fatigue crack growth and fracture strengths of cracked specimens. Such specimens represent typical aircraft structural details (such as cracks from holes). These specimens were subjected to simple constant amplitude loading and to more complex flight load histories. Test data from both in house tests and from the literature are used to substantiate the analytical methods. These analyses extended the theory of fracture mechanics to deal with fatigue crack growth and fracture of complex crack configurations that are typical of aircraft materials and structural details.

J. C. Newman, Jr.↗