Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Power Take Off”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1934

Complete tank tests of two flying-boat hulls with pointed steps - N.A.C.A. Models 22-A and 35

This note presents the results of complete tank test of N.A.C.A. Models 22-A and 35, two flying-boat hulls of the deep pointed-step type with low dead rise. Model 22-A is a form derived by modification of Model 22, the test results of which are given in N.A.C.A. Technical Note No. 488. Model 35 is a form of the same type but has a higher length-beam ratio than either Model 22 or 22-A. Take-off examples are worked out using data from these tests and a previous test of a conventional model applied to an arbitrary set of design specifications for a 15,000-pound flying boat. The comparison of these examples shows both pointed-step models to be superior to the conventional form, and Model 35 to be the better of the two. Model 35 is applied to a hypothetical 100,000-pound flying boat of the twin-hull type and performance calculations are made both for take-off and range. The results indicate that the high performance of this type of hull will enable the designer to use higher wing and power loadings than are found in current practice, with a resulting increase in range and pay load.

Shoemaker, James M↗
NASA NTRS1994

On extending parallelism to serial simulators

This paper describes an approach to discrete event simulation modeling that appears to be effective for developing portable and efficient parallel execution of models of large distributed systems and communication networks. In this approach, the modeler develops submodels using an existing sequential simulation modeling tool, using the full expressive power of the tool. A set of modeling language extensions permit automatically synchronized communication between submodels; however, the automation requires that any such communication must take a nonzero amount off simulation time. Within this modeling paradigm, a variety of conservative synchronization protocols can transparently support conservative execution of submodels on potentially different processors. A specific implementation of this approach, U.P.S. (Utilitarian Parallel Simulator), is described, along with performance results on the Intel Paragon.

Nicol, David↗
NASA NTRS1958

Low-Speed Aerodynamic and Hydrodynamic Characteristics of a Proposed Supersonic Multijet Water-Based Hydro-Ski Aircraft with Upward-Rotating Engines

The low-speed aerodynamic and hydrodynamic characteristics of a proposed multijet water-based aircraft configuration for supersonic operation have been investigated. The design features include upward-rotating engines, body indentation, a single hydro-ski, and a wing with an aspect ratio of 3.0, a taper ratio of 0.143, 36.90 sweepback of the quarter-chord line, and NACA 65AO04 airfoil sections. For the aerodynamic investigation, with the flaps retracted, the model was longitudinally and directionally stable up to the stall. The all-movable horizontal tail was capable of trimming the model up to a lift coefficient of approximately 0.87. All flap configurations investigated had a tendency to become longitudinally unstable at stall. The effectiveness of the all-movable horizontal tail increased with increasing lift coefficient for all flap configurations investigated; however, with the large static margin of the configuration with the center of gravity at 0.25 mean aerodynamic chord, the all-movable horizontal tail was not powerful enough to trim all the various flapped configurations investigated throughout the angle-of-attack range. For the hydrodynamic investigation, longitudinal stability during take-offs and landings was satisfactory. Decreasing the area of the hydro-ski 60 percent increased the maximum resistance and emergence speed 40 and 70 percent, respectively. Without the jet exhaust, the resistance was reduced by simulating the vertical-lift component of the forward engines rotated upward. However, the jet exhaust of the forward engines increased the maximum resistance approximately 60 percent. The engine inlets and horizontal tail were free from spray for all loads investigated and for both hydro-ski sizes.

Petynia, William W.↗
NASA NTRS2001

Academy Sharing Knowledge (ASK). The NASA Source for Project Management Magazine

How big is your project world? Is it big enough to contain other cultures, headquarters, hierarchies, and weird harpoon-like guns? Sure it is. The great American poet Walt Whitman said it best, 'I am large/I contain multitudes.' And so must you, Mr. and Ms. Project Manager. In this issue of ASK, we look outside the project box. See how several talented project managers have expanded their definition of project scope to include managing environments outside the systems and subsystems under their care. Here's a sampling of what we've put together for you this issue: In 'Three Screws Missing,' Mike Skidmore tells about his adventures at the Plesetek Cosmodrome in northern Russia. Ray Morgan in his story, 'Our Man in Kauai,' suggests we take a broader view of what's meant by 'the team.' Jenny Baer-Riedhart, the NASA program manager on the same Pathfinder solar-powered airplane, schools us in how to sell a program to Headquarters in 'Know Thyself--But Don't Forget to Learn About the Customer Too.' Scott Cameron of Proctor and Gamble talks about sharpening your hierarchical IQ in 'The Project Manager and the Hour Glass.' Mike Jansen in 'The Lawn Dart' describes how he and the 'voodoo crew' on the Space Shuttle Advanced Solid Rocket Motor program borrowed a harpoon-like gun from the Coast Guard to catch particles inside of a plume. These are just some of the stories you'll find in ASK this issue. We hope they cause you to stop and reflect on your own project's relationship to the world outside. We are also launching a new section this issue, 'There are No Mistakes, Only Lessons.' No stranger to ASK readers, Terry Little inaugurates this new section with his article 'The Don Quixote Complex.'

Post, Todd↗
NASA NTRS2004

Status of Low Thrust Work at JSC

High performance low thrust (solar electric, nuclear electric, variable specific impulse magnetoplasma rocket) propulsion offers a significant benefit to NASA missions beyond low Earth orbit. As NASA (e.g., Prometheus Project) endeavors to develop these propulsion systems and associated power supplies, it becomes necessary to develop a refined trajectory design capability that will allow engineers to develop future robotic and human mission designs that take advantage of this new technology. This ongoing work addresses development of a trajectory design and optimization tool for assessing low thrust (and other types) trajectories. This work targets to advance the state of the art, enable future NASA missions, enable science drivers, and enhance education. This presentation provides a summary of the low thrust-related JSC activities under the ISP program and specifically, provides a look at a new release of a multi-gravity, multispacecraft trajectory optimization tool (Copernicus) along with analysis performed using this tool over the past year.

Condon, Gerald L.↗
NASA NTRS2018

Determining Thermal Capabilities for External Transfer Operations on the International Space Station

External transfers on the International Space Station (ISS) have a degree of difficulty caused by the severity of the radiative thermal environment and the complexity of the operational choreography to perform the installation and activation of the hardware. These transfers can be performed robotically, by astronauts during an Extra Vehicular Activity (EVA - spacewalk), or combination of robotic/crew operations. Robotic transfers may include capability to intermittently power the hardware; while the hardware remains unpowered for EVA operations. Robotic transfers can be staged to occur in a favorable thermal environment, though typically take longer than a transfer by crew during an EVA where the hardware may not be robotically compatible. The hardware is under passive thermal control, use of optics/multi-layer insulation/heaters, while being transferred from/to a visiting vehicle, airlock, stowage platform, or external ISS structure and may include additional design components, such as removable protective blankets, to meet the transfer requirements. Thermal analysis must be performed to determine the capability of the hardware being transferred to provide the Mission Control team the products necessary to plan and execute the operation while establishing an awareness for any contingency response. An overview of the thermal aspects in planning these types of transfer operations, the analytical approaches and assumptions, and examples of results are provided in this paper.

Thermal↗
NASA NTRS2022

Improved Prediction of Losses with Large Eddy Simulation in a Low-Pressure Turbine

There is a need to improve predictions of losses resulting from large eddy simulations (LES) of low-pressure turbines (LPT) in gas turbines. This may be done by assessing the accuracy of predictions against validation data and understanding the source of any inaccuracies. LES is a promising approach for capturing the laminar/turbulent transition process in a LPT. In previous studies, the authors utilized LES to model the flow field over a Variable Speed Power Turbine (VSPT) blade and successfully captured characteristic features of separation/reattachment and transition on the suction side at both the cruise (positive incidence) and take-off conditions (negative incidence) and as well, simulated the effect of free-stream turbulence (FST) on those phenomena. The predicted pressure loading profiles agreed well with the experimental data for both a high and a low FST case at a Reynolds number of Re(ex)=220,000. In this paper, we present wake profiles resulting from computations for a range of FST values. Although the predicted wake profiles for the lowest FST case (Tu=0.5%) matched the experimental data, at higher FST (Tu=10-15%,) the wake was wider than the experimentally measured wake and for both cases were displaced laterally when compared to the experimental measurements. In our investigation of the causes of the said discrepancies we have identified important effects which could strongly influence the predicted wake profile. Predicted losses were improved by assuring the validity of the flow solution. This was done by utilizing spectral analysis to scrutinize the dynamic behavior of the wake and determine solution accuracy resulting from low mesh density and low accuracy of convective modeling.

LES-LDKM↗
NASA NTRS2009

A Distributed Prognostic Health Management Architecture

This paper introduces a generic distributed prognostic health management (PHM) architecture with specific application to the electrical power systems domain. Current state-of-the-art PHM systems are mostly centralized in nature, where all the processing is reliant on a single processor. This can lead to loss of functionality in case of a crash of the central processor or monitor. Furthermore, with increases in the volume of sensor data as well as the complexity of algorithms, traditional centralized systems become unsuitable for successful deployment, and efficient distributed architectures are required. A distributed architecture though, is not effective unless there is an algorithmic framework to take advantage of its unique abilities. The health management paradigm envisaged here incorporates a heterogeneous set of system components monitored by a varied suite of sensors and a particle filtering (PF) framework that has the power and the flexibility to adapt to the different diagnostic and prognostic needs. Both the diagnostic and prognostic tasks are formulated as a particle filtering problem in order to explicitly represent and manage uncertainties; however, typically the complexity of the prognostic routine is higher than the computational power of one computational element ( CE). Individual CEs run diagnostic routines until the system variable being monitored crosses beyond a nominal threshold, upon which it coordinates with other networked CEs to run the prognostic routine in a distributed fashion. Implementation results from a network of distributed embedded devices monitoring a prototypical aircraft electrical power system are presented, where the CEs are Sun Microsystems Small Programmable Object Technology (SPOT) devices.

Bhaskar, Saha↗
NASA NTRS1989

Low-speed wind tunnel performance of high-speed counterrotation propellers at angle-of-attack

The low-speed aerodynamic performance characteristics of two advanced counterrotation pusher-propeller configurations with cruise design Mach numbers of 0.72 were investigated in the NASA Lewis 9- by 15-Foot Low-Speed Wind Tunnel. The tests were conducted at Mach number 0.20, which is representative of the aircraft take-off/landing flight regime. The investigation determined the effect of nonuniform inflow on the propeller performance characteristics for several blade angle settings and a range of rotational speeds. The inflow was varied by yawing the propeller model to angle-of-attack by as much as plus or minus 16 degrees and by installing on the counterrotation propeller test rig near the propeller rotors a model simulator of an aircraft engine support pylon and fuselage. The results of the investigation indicated that the low-speed performance of the counterrotation propeller configurations near the take-off target operating points were reasonable and were fairly insensitive to changes in model angle-of-attack without the aircraft pylon/fuselage simulators installed on the propeller test rig. When the aircraft pylon/fuselage simulators were installed, small changes in propeller performance were seen at zero angle-of-attack, but fairly large changes in total power coefficient and very large changes of aft-to-forward-rotor torque ratio were produced when the propeller model was taken to angle-of-attack. The propeller net efficiency, though, was fairly insensitive to any changes in the propeller flowfield conditions near the take-off target operating points.

Hughes, Christopher E.↗
NASA NTRS1989

Low-speed wind tunnel performance of high-speed counterrotation propellers at angle-of-attack

The low-speed aerodynamic performance characteristics of two advanced counterrotation pusher-propeller configurations with cruise design Mach numbers of 0.72 were investigated in the NASA Lewis 9- by 15-Foot Low-Speed Wind Tunnel. The tests were conducted at Mach number 0.20, which is representative of the aircraft take/off/landing flight regime. The investigation determined the effect of nonuniform inflow on the propeller performance characteristics for several blade angle settings and a range of rotational speeds. The inflow was varied by yawing the propeller mode to angle-of-attack by as much as plus or minus 16 degrees and by installing on the counterrotation propeller test rig near the propeller rotors a model simulator of an aircraft engine support pylon and fuselage. The results of the investigation indicated that the low-speed performance of the counterrotation propeller configurations near the take-off target operating points were reasonable and were fairly insensitive to changes in model angle-of-attack without the aircraft pylon/fuselage simulators installed on the propeller test rig. When the aircraft pylon/fuselage simulators were installed, small changes in propeller performance were seen at zero angle-of-attack, but fairly large changes in total power coefficient and very large changes of aft-to-forward-rotor torque ratio were produced when the propeller model was taken to angle-of-attack. The propeller net efficiency, though, was fairly insensitive to any changes in the propeller flowfield conditions near the take-off target operating points.

Hughes, Christopher E.↗
NASA NTRSDate not supplied

Development and Integration of a Thermal Management Simulation for a Quadrotor Parallel Hybrid Propulsion System

This paper details the development of a propulsion system simulation for a six-passenger parallel hybrid quadrotor and utilizes the Numerical Propulsion System Simulation (NPSS) along with the NPSS Power System Library as the development environment. This simulation integrates an engine power plant with an electrical generation and distribution system and includes the required thermal management system. The thermal management system is comprised of liquid cooling loops that reject the heat load through air to coolant heat exchangers and utilizes a map-based performance estimation method. This method is developed within NPSS and detailed in this paper. The full system model is designed to predict system weight, range, and performance through a proposed mission profile. Results of the paper show an all-engine system maintains the best range, while a mostly electric system that utilizes an engine as a backup or a conditional power contributor offers range benefit.

Vertical lift and take off vehicle↗
NASA NTRSDate not supplied

High-Intensity Radiated Field (HIRF) Map - An Avoidance Approach for UAM, AAM, and UAS Vehicles

Advanced Air Mobility (AAM), Urban Air Mobility (UAM), and Unmanned Aerial Systems (UAS) vehicles will fly in similar airspace to Transport Category Rotorcraft, thereby requiring them to meet the most severe requirements for HighIntensity Radiated Fields (HIRF) certification. The environment is severe for rotorcraft, much more so than for fixed-wing aircraft, due to lower altitude operations, potentially exposing the vehicles to close and direct view of high-power transmitters on the ground. High-level HIRF exposure potentially leads to avionic system upsets, interference, and undesirable effects. Shielding and circuit protection against HIRF will be a significant barrier to size, weight, and cost, especially for emerging electric vertical take-off and landing (eVTOL) and electric short take-off and landing (eSTOL) vehicles. This paper proposes a novel approach to HIRF protection, which reduces costs by testing and certifying vehicles to a “vehicle tolerance level” that is lower than required for Transport Category Rotorcraft. The remaining protection is achieved by maintaining a safe distance from known HIRF sources, calculated based on the vehicle's tolerance level and transmitter characteristics such as transmit power, antenna beamwidth, and direction. Tailored maps are developed, identifying transmitters and avoidance zones within an operating area or along a flight path, allowing for restricted vehicle operations. The HIRF avoidance zones could be smaller for vehicles with higher tolerance levels, enabling them to operate closer to transmitters. Transmitter data can be extracted from regulatory databases like the FCC and NOAA. A map tool is developed in Matlab to calculate and plot HIRF avoidance zones from transmitters in FCC and NOAA databases as proof of concept. Illustrations are presented for AM/FM/TV transmitters, communication satellite dishes, and weather radars. Also illustrated are HIRF zones for smaller transmitters, including land-mobile radios, pagers, microwave links, and cellular towers. An example of flight planning around the transmitters is presented. This method is a substantial deviation from the standard approach and involves slightly higher flight-planning complexity, but the potential cost savings are significant. Future AAM/UAM/UAS aeronautical charts could include these new HIRF avoidance zones.

HIRF↗
NASA NTRSDate not supplied

High-Intensity Radiated Field (HIRF) Map - An Avoidance Approach for UAM, AAM, and UAS Vehicles

Advanced Air Mobility (AAM), Urban Air Mobility (UAM), and Unmanned Aerial Systems (UAS) vehicles will fly in similar airspace to Transport Category Rotorcraft, thereby requiring them to meet the most severe requirements for High Intensity Radiated Fields (HIRF) certification. The environment is severe for rotorcraft, much more so than for fixed-wing aircraft, due to lower altitude operations, potentially exposing the vehicles to close and direct view of high-power transmitters on the ground. High-level HIRF exposure potentially leads to avionic system upsets, interference, and undesirable effects. Shielding and circuit protection against HIRF will be a significant barrier to size, weight, and cost, especially for emerging electric vertical take-off and landing (eVTOL) and electric short take-off and landing (eSTOL) vehicles. This paper proposes a novel approach to HIRF protection, which reduces costs by testing and certifying vehicles to a “vehicle tolerance level” that is lower than required for Transport Category Rotorcraft. The remaining protection is achieved by maintaining a safe distance from known HIRF sources, calculated based on the vehicle's tolerance level and transmitter characteristics such as transmit power, antenna beamwidth, and direction. Tailored maps are developed, identifying transmitters and avoidance zones within an operating area or along a flight path, allowing for restricted vehicle operations. The HIRF avoidance zones could be smaller for vehicles with higher tolerance levels, enabling them to operate closer to transmitters. Transmitter data can be extracted from regulatory databases like the FCC and NOAA. A map tool is developed in Matlab to calculate and plot HIRF avoidance zones from transmitters in FCC and NOAA databases as proof of concept. Illustrations are presented for AM/FM/TV transmitters, communication satellite dishes, and weather radars. Also illustrated are HIRF zones for smaller transmitters, including land-mobile radios, pagers, microwave links, and cellular towers. An example of flight planning around the transmitters is presented. This method is a substantial deviation from the standard approach and involves slightly higher flight-planning complexity, but the potential cost savings are significant. Future AAM/UAM/UAS aeronautical charts could include these new HIRF avoidance zones.

HIRF↗
NASA NTRS2003

Single Event Effects Testing of the Linfinity SG1525A Pulse Width Modulator Controller

Pulse Width Modulator (PWM) Controllers are the heart of switching power supply systems in development today. The PWMs considered here have the same integration advantages as many other controllers but it also includes the interface drivers for the follow-on power Field Effect Transistors (FET). Previous work on these types of devices looked into the required test methodologies [ 11 and the impact of radiation on the soft start and shutdown circuits of typically incorporated in the technology [2]. Taking advantage of this previous work this study was undertaken to determine the single event destructive and transient susceptibility of the Linfinity SG1525A Pulse Width Modulator Controller. The device was monitored for transient interruptions in the output signals and for destructive events induced by exposing it to a heavy ion beam at the Texas A&M University Cyclotron Single Event Effects Test Facility. After exposing these devices to the beam, a new upset mode has been identified that can lead to catastrophic power supply system failure if this event would occur while drive power FETs off the two device outputs. The devices and the test methods used will be described first. This will be followed by a brief description of the data collected to date (not all data can be presented with the length constraints of the summary) and a summary of the key results.

Howard, J. W., Jr.↗
NASA NTRS1968

An improved magnetic tape recorder

Magnetic tape recorder employs a single capstan for simultaneously driving the supply and take-up reels in such a manner that the tape passing between the reels is kept under a predetermined constant tension. This recorder operates with little power and is sufficiently rugged to withstand the severe stresses encountered in high-altitude balloon flight tests.

Uber, P. W.↗
NASA NTRS1972

Microwave conductivity of slightly ionized gases and electromagnetic scintillations

Two areas of research are briefly summarized. The first is concerned with calculating the conductivity of a slightly ionized gas. A method is proposed which involves an expansion of the Boltzmann collision operator (of the electron distribution function, involving the neutral gas-electron interactions) in powers of the electron-gas mass ratio. The second area of investigation focuses on the problem of a radio wave propagating through the interplanetary medium, taking account of the decreasing plasma density with distance from the sun.

Mintzer, D.↗
NASA NTRS1987

Thermal and Electrical Recharging of Sodium/Sulfur Cells

Efficiency as high as 60 percent achieved. Proposed thermal and electrical recharging scheme expected to increase overall energy efficiency of battery of sodium/sulfur cells (beta cells). Takes advantage of peculiarity in chemical kinetics of recharge portion of operating cycle to give thermal assist to electrically driven chemical reactions. Future application include portable power supplies and energy storage in commercial power systems during offpeak periods.

Richter, Robert↗
NASA NTRS1991

Conceptual design of two-stage-to-orbit hybrid launch vehicle

The object of this design class was to design an earth-to orbit vehicle to replace the present NASA space shuttle. The major motivations for designing a new vehicle were to reduce the cost of putting payloads into orbit and to design a vehicle that could better service the space station with a faster turn-around time. Another factor considered in the design was that near-term technology was to be used. Materials, engines and other important technologies were to be realized in the next 10 to 15 years. The first concept put forth by NASA to meet these objectives was the National Aerospace Plane (NASP). The NASP is a single-stage earth-to-orbit air-breathing vehicle. This concept ran into problems with the air-breathing engine providing enough thrust in the upper atmosphere, among other things. The solution of this design class is a two-stage-to-orbit vehicle. The first stage is air-breathing and the second stage is rocket-powered, similar to the space shuttle. The second stage is mounted on the top of the first stage in a piggy-back style. The vehicle takes off horizontally using only air-breathing engines, flies to Mach six at 100,000 feet, and launches the second stage towards its orbital path. The first stage, or booster, will weigh approximately 800,000 pounds and the second stage, or orbiter will weigh approximately 300,000 pounds. The major advantage of this design is the full recoverability of the first stage compared with the present solid rocket booster that are only partially recoverable and used only a few times. This reduces the cost as well as providing a more reliable and more readily available design for servicing the space station. The booster can fly an orbiter up, turn around, land, refuel, and be ready to launch another orbiter in a matter of hours.

Source record↗