Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Phase shift”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Suppression of ITG turbulence due to spectral shift during biasing induced H-mode on HBT-EP

Investigations of biasing induced H-mode discharges on HBT-EP show that the edge turbulence is consistent with the ion temperature gradient) mode and have allowed for the controlled observation of the effect of applied flow shear on the turbulence. Measurements of the radial wavenumber spectrum of floating potentials at the edge show that the turbulence intensity decreases with increasing shift in the spectrum average ⟨ k r ⟩ when increasing amounts of bias probe voltage (and increasing amounts of flow shear) is applied. This is in agreement with the spectral shift model [Staebler et al., Phys. Rev. Lett. 110, 055003 2013] for turbulence suppression via sheared flow. A shift in the wavenumber spectrum occurs at applied electrode voltages and currents below the threshold needed for an L–H transition, and a dithering transition is obtained when biasing near the threshold. Suppression of blob-filament turbulence in the scrape-off layer (SOL) precedes the L–H transition, with the SOL turbulence remaining low throughout the dithering phase, despite the modulation of turbulence levels in the nearby edge. This demonstrates that the SOL turbulence “decouples” from the edge turbulence. The spectral shift in the measured radial wavenumber is corroborated by the direct measurement of eddy tilt angle using a novel time delay analysis technique first developed for Doppler reflectometry [Pinzon et al., Plasma Phys. Controlled Fusion 61, 105009 (2019)] but adapted here for floating potential measurements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Characterizing core and edge turbulence regimes with fluctuation imaging diagnostics in Wendelstein 7-X

Two density fluctuation imaging systems, phase contrast imaging (PCI) and gas puff imaging (GPI) measure spatially resolved density fluctuations with high time resolution throughout the core plasma (PCI) and in the scrape-off layer (GPI) of the Wendelstein 7-X (W7-X) stellarator. Both systems combined give a comprehensive overview of overall fluctuation levels, spectral properties such as their distribution in frequency and wavenumber space as well as their spatial distribution. These tools are used to assess changes in density turbulence in three representative discharges that transition into stable divertor detachment by different strategies (impurity seeding, density ramping and power starvation). Several general trends are identified when the radiated power fraction is systematically increased: In the plasma edge, the line emission observed by GPI shifts radially inward with a drop in electron temperature, and normalized intensity fluctuation profiles follow this inward shift. Skewness and kurtosis of these edge fluctuations are reduced, indicating a reduction of large intermittent transport events, and poloidal phase velocities decrease in magnitude. These observations are consistent with a reduced power input into the plasma edge and a general reduction of turbulent activity. Core density fluctuation levels remain nearly constant in the impurity seeding scenario, indicating that detachment does not significantly impact turbulence there. However, a strong reduction in the dominant outboard fluctuation phase velocity is observed that deviates from the previous interpretation of neoclassical radial electric field changes, showing that the core plasma is not completely unaffected. In the density ramp and power starvation scenarios, undesirable and irregular large-scale events arise clearly in both diagnostic systems as the radiative fraction is increased. Impurity seeding therefore seems to be a promising strategy on W7-X to achieve detachment without significantly altering core turbulence, especially when targeting a specific operating point in core density and heating power.

Wendelstein 7-X↗
DOE OSTI2022

High-Temperature Ceramic-Carbonate Dual-Phase Membrane Reactor for Pre-combustion Carbon Dioxide Capture (Final Scientific/Technical Report)

Arizona State University, in collaboration with University of South Carolina, worked on a project aimed at development of a new high temperature, high pressure CO 2 perm-selective membrane reactor for water-gas-shift reaction (WGS) with simulated gasifier syngas to produce a high concentration H 2 stream with CO 2 capture. The membrane reactor is made of a CO 2 semi-permeable ceramic-carbonate dual-phase (CCDP) membrane with high CO 2 perm-selectivity/permeance and thermal/mechanical stability for application in WGS reaction. The objectives of this project were to (1) synthesize the chemically/thermally stable tubular CCDP membranes with CO 2 permeance and selectivity (with respect to H 2 , CO or H 2 O) larger than 6.5×10-7 mol/m2·s·Pa and 500, respectively; (2) establish CCDP membrane reactor setup and study high pressure CO 2 permeation and WGS reaction with CO 2 capture using the setup; and (3) identify conditions for WGS in the CCDP membrane reactor that produce CO 2 and H 2 streams with purity of >99% and >90% respectively at CO conversion >95% and overall carbon capture >90%. The work in this project included both membrane development and membrane reactor process study. The membrane development efforts were focused on investigating a H 2 S resistant and highly oxygen-ionic conducting metal oxide material and membrane for CO 2 separation, fabrication of tubular samaria-doped-ceria/molten-carbonate CCDP membrane with high mechanical strength, and experimental and modeling study of high-pressure CO 2 permeation of the CCDP membranes. Mathematical models were developed to describe WGS in the CCDP membrane reactor without a catalyst or packed with a commercial high temperature WGS catalyst. Experiments on WGS in the CCDP membrane reactor with the commercial WGS catalyst, guided by the model analysis, were performed to identify optimum conditions for achieving the CO conversion, carbon capture, and the purity of the H 2 and CO 2 streams mentioned above. At 30 atm feed pressure, 750°C operation temperature, space velocity of 250 h-1, and with steam sweep, a single-stage CCDP membrane reactor with average CO 2 permeation flux of 0.5 cm3(STP)/min.cm2 can achieve CO 2 conversion of 95% and overall carbon capture of 94%, and produce CO 2 and H 2 streams with dry-based purity of >99% and 92% respectively. The project also included process design and techno-economic analysis (TEA) for a CCDP membrane reactor process for WGS reaction with CO 2 capture for a 550 MW coal-fired IGCC power plant, and its comparison with the conventional fixed-bed reactor system for WGS with follow-up CO 2 capture by an amine absorption process. The target performance for the reactor for WGS with CO 2 capture includes CO conversion >95%, hydrogen stream purity >90%, CO 2 stream purity >95%, and total carbon capture >90%. The CCDP membrane developed in this project can achieve the performance target, without subsequent CO 2 capture process at the optimum conditions identified in this project. The outcome of the process design and TEA analysis shows that the membrane reactor for WGS with in-situ CO 2 capture has an operating cost about 40% lower than that for the conventional fixed-bed reactor with a separate amine absorption process for CO 2 capture. However, the capital cost of the membrane reactor process is about twice that of the conventional process because of the higher cost of the CCDP membrane. Modeling analysis shows that a membrane reactor using a CCDP membrane with higher CO 2 permeance (about three times the current value) can deliver the targeted performance for WGS reaction with CO 2 capture at a much higher space velocity and lower membrane surface area to catalyst volume ratio, leading to a smaller catalyst amount and/or membrane area and hence significantly reduced membrane reactor capital costs.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2025

Understanding the deformation behavior of the γ rich transformative Fe 38.5 Mn 20 Co 20 Cr 15 Si 5 Cu 1.5 complex concentrated alloy using in situ synchrotron diffraction

In situ tensile testing coupled with synchrotron x-ray diffraction was used to study the deformation behavior of metastability-engineered Fe 38.5 Mn 20 Co 20 Cr 15 Si 5 Cu 1.5 complex concentrated alloy. Monitoring the evolution of phase fraction and strain hardening response allowed the determination of true critical stress for the onset of the transformation-induced plasticity (TRIP) to be ∼375 MPa, preceded by slip starting at ∼255 MPa. In situ EBSD was used to validate the critical stress for transformation at the microstructure level and observe slip traces to confirm prior slip activity before the transformation. Further, a modeling framework based on stacking fault energy (SFE) was developed to predict the critical stress for transformation. Modeling suggested the SFE of the alloy to fall nearly 15 mJ/m 2 , which agrees well with SFE values calculated using synchrotron peak shifting (12 mJ/m 2 ) and thermodynamic calculation (11 mJ/m 2 ). As a result of γ-fcc to ε-hcp phase transformation, new {0002} ε planes emerged parallel to unaligned {111} γ planes with the tensile loading following S-N orientation relationship. Such selective emergence of new diffraction rings corresponding to ε phase is understood based on the reorientation of γ crystals with reference to tensile axis. In conclusion, this approach can be extended to effectively design alloys based on critical stress required for activating different deformation mechanisms to further push the limits of the strength-ductility envelope.

Complex concentrated alloy↗
DOE OSTI2026

Novel thermal energy storage component: Development, performance, and phase transition diagnosis

Thermal energy storage (TES) using phase change materials (PCMs) is a promising technology for capturing and storing excess thermal energy for later use. However, challenges such as poor heat transfer efficiency and a lack of modular, scalable designs have limited widespread adoption of TES in real-world applications. This study developed and evaluated modular brick-type and blade-type TES prototypes featuring an aluminum housing, an embedded serpentine coil for active or passive thermal exchange, and a cost-effective metal mesh to enhance PCM thermal conductivity. The blade-type TES achieved notable geometric efficiency, with a thickness-to-length ratio of 0.03 and a thickness-to-width ratio of 0.08, enabling highly compact and modular thermal storage suitable for space-constrained applications. The paper presents a detailed evaluation of the TES prototypes’ performance. The comparative analysis indicated that the TES prototypes provide a highly cost-effective, thermally optimized alternative for compact energy storage and load shifting. A novel diagnostic technique was also introduced: using a portable endoscope to capture real-time visualizations of PCM phase transitions inside the TES. This method provides critical insights into internal heat transfer mechanisms, identifies potential issues, and offers valuable support for optimizing the TES design and developing the control algorithm. Overall, the modular brick-type and blade-type TES designs demonstrated in this work provide a scalable, efficient, and economically viable solution for advancing TES across residential, commercial, and industrial sectors. The designs’ compact structure, enhanced thermal performance, and integrated diagnostic capabilities make them strong candidates for future deployment in energy-efficient systems.

Gao, Zhiming [ORNL] (ORCID:0000000271397995)↗
DOE OSTI2020

Structure and activity of supported bimetallic NiPd nanoparticles: influence of preparation method on CO 2 reduction

Here, bimetallic Ni-Pd and monometallic reference catalysts were prepared by decomposing organometallic precursors, Ni(cod) 2 and Pd 2 (dba) 3 , leading to nanoparticles with sizes ranging from 3 to 6 nm. Two different synthesis procedures were followed: i) solution synthesis using capping ligand (hexadecylamine) followed by impregnation of pre-formed nanoparticles on SiO 2 , called Sol-immobilization (SI); and 2) direct precursor decomposition onto SiO 2 , without stabilizer, called Direct Decomposition (DD). Samples prepared by SI procedure are alloyed bimetallic nanoparticles, whereas samples obtained by DD one show phase segregation. Interestingly, DD samples show better activity for CO 2 hydrogenation into CO (reverse water-gas shift reaction - RWGS) than SI ones. The best compromise between activity for CO 2 activation (at lower temperature) and CO selectivity was achieved with Ni DD and NiPd DD catalysts. Moreover, the addition of palladium increased the concentration of surface undercoordinated sites, which chemisorb CO weakly, thus improving activity and selectivity, in opposition to other samples that chemisorb CO strongly, in multiband configuration. In the presence of Pd, different decomposition rates drive the formation of smaller and more active Ni clusters. The knowledge acquired here on the influence of synthesis conditions on the catalytic properties of Ni-Pd catalysts should guide us to better catalysts for CO 2 transformations into valuable products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Numerical modeling and parametric study of a dual purpose underground thermal battery

We report integrating thermal energy storage with building energy systems can enable flexible building electric demands at buildings to help mitigate the mismatch between electricity supply and demand. A novel building heating and cooling system that integrates a dual-source heat pump with hybrid thermal storage named dual-purpose underground thermal battery (DPUTB) has been developed for reshaping building electric demands. The proposed DPUTB integrated geothermal heat pump system is an original innovation that enables Grid-interactive Energy Efficient buildings. This paper focuses on the study of the novel DPUTB. The DPUTB works as both a thermal storage tank (an inner tank) and a ground heat exchanger (an outer tank separated from the inner tank by the insulation material). High fidelity and computationally effective models are needed to predict the performance of the novel DPUTB. This study has developed a simplified dynamic model for the DPUTB according to heat transfer and energy conservation principles and validated it by using experimental data obtained from testing a small-scale DPUTB apparatus. A parametric study was conducted to identify a design that can achieve the target thermal storage performance of load shift and energy efficiency. The parametric study results show that the inner tank shell thermal conductivity and the phase change material's melting point are the two most influencing factors on the performance of the DPUTB. One single full-size DPUTB with the identified design could provide 1-ton cooling (3.51 kW) with the supply temperature lower than 11 °C for 4 hours in summer after being fully charged in 8 hours. The inner tank filled with phase change material is for cooling thermal storage as a latent tank in the design. However, its capacity can be as high as 60 MJ as a sensible water tank for heating storage in winter. In the future study, the DPUTB model will be incorporated into the dual-source heat pump system for evaluating the overall system performance of demand side management in the long term.

25 ENERGY STORAGE↗
DOE OSTI2020

Water Uptake by Silica Nanopores: Impacts of Surface Hydrophilicity and Pore Size

Water uptake at 298 K by two mesoporous silicas with different pore sizes was studied using volumetric vapor sorption. Here, through variation of sample pretreatment temperature and time, the number of surface hydroxyl groups was varied, leading to marked changes in the water sorption behavior. With increasing surface hydroxyl density, the adsorption of water to the pore surfaces increases, leading to formation of a thicker and denser water sorption layer. The BET model was used to measure surface hydroxyl density from low pressure parts of water adsorption isotherms. Adsorption of water molecules scales with the number density of surface hydroxyl groups, and monolayer coverage is reached at reduced pressure of ca. 0.3. The onset of adsorption pore condensation of water shifts to lower reduced pressure with increasing surface hydroxyl density, indicating growing thickness of adsorption layers. However, the water pore condensation step of the desorption branch shifts to smaller reduced pressure with increasing surface hydroxylation, reducing the adsorption-desorption hysteresis width. An adsorbed phase model is utilized to calculate the distribution of pore water molecules between adsorbed and pore condensation phases, and characterize the density and thickness of the water sorption phase. In the smaller pores, the adsorbed phase forms a sparse monolayer, while approximately a bilayer is formed in the wider pores. The previously reported silica nanopore underfilling by water is confirmed and rationalized by a significantly reduced water density in the adsorbed phase with respect to bulk, while the pore core is filled with water of approximately bulk density.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Exploiting SMILEs and the CMIP5 Archive to Understand Arctic Climate Change Seasonality and Uncertainty

Arctic Amplification (AA) exhibits a distinct seasonal dependence; it is weakest in boreal summer and strongest in winter. Here, we analyze simulations from single-model initial-condition large ensembles and Coupled Model Intercomparison Project Phase 5 to decipher the seasonal evolution of Arctic climate change. Models agree that the annual maximum AA shifts from autumn into winter over the 21st century, accompanied by similar shifts in sea-ice loss and surface turbulent heat fluxes, whereas the maximum precipitation shifts only into late autumn. However, the exact seasonal timing and magnitude of these shifts are highly uncertain. Decomposing the uncertainty into model structural differences, emission scenarios, and internal variability reveals that model differences dominate the total uncertainty, which also undergo autumn-to-winter shifts. We also find that the scenario uncertainty is unimportant for projections of AA. These results highlight that understanding model differences is critical to reducing uncertainty in projected Arctic climate change.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Systematic Validation of Ensemble Cloud-Process Simulations using Polarimetric Radar Observations and Simulator over the NASA Wallops Flight Facility

The BiLateral Operational Storm-Scale Observation and Modeling (BLOSSOM) project was initiated to establish a long-term supersite to improve understanding of cloud physical states and processes as well as to support satellite and climate model programs over the WFF site via a bilateral approach of storm-scale observations and process modeling. This study highlights a noble systematic validation framework of the BLOSSOM ensemble cloud-process simulations through mixed-phase, light-rain, and deep-convective precipitation cases. The framework consists of creating a domain-shifted ensemble of large-scale forcing datasets, and configuring and performing cloud-process simulations with three different bulk microphysics schemes. Validation uses NASA S-band dual-POLarimetric radar (NPOL) observations in the form of statistical composites and skill scores via a polarimetric radar simulator and newly developed CfRad Data tool (CfRAD). While the simulations capture the overall structures of the reflectivity composites, polarimetric signals are still poorly simulated, mainly due to a lack of representation of ice microphysics diversity in shapes, orientation distributions, and their complex mixtures. Despite the limitation, this new ensemble-based validation framework demonstrates that 1) no particular forcing or microphysics scheme outperforms the rest and 2) the skill scores of coarse- and fine-resolution ensemble simulations with different domain-shifted forcing and microphysics schemes are highly correlated with each other with no clear improvement. On the other hand, this suggests that coarse-resolution ensemble simulations are relevant for selecting the best meteorological forcing and microphysics scheme before conducting computationally demanding large eddy simulations (LESs) in support of aircraft and satellite instrument development as well as cloud-precipitation-convection parameterizations.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Unravelling the mechanism of pressure induced polyamorphic transition in an inorganic molecular glass

The atomic structure of a germanium doped phosphorous selenide glass of composition Ge 2.8 P 57.7 Se 39.5 is determined as a function of pressure from ambient to 24 GPa using Monte-Carlo simulations constrained by high energy x-ray scattering data. The ambient pressure structure consists primarily of P 4 Se 3 molecules and planar edge shared phosphorus rings, reminiscent of those found in red phosphorous as well as a small fraction of locally clustered corner-sharing GeSe 4 tetrahedra. This low-density amorphous phase transforms into a high-density amorphous phase at ~6.3 GPa. The high-pressure phase is characterized by an extended network structure. The polyamorphic transformation between these two phases involves opening of the P 3 ring at the base of the P 4 Se 3 molecules and subsequent reaction with red phosphorus type moieties to produce a cross linked structure. The compression mechanism of the low-density phase involves increased molecular packing, whereas that of the high pressure phase involves an increase in the nearest-neighbor coordination number while the bond angle distributions broaden and shift to smaller angles. The entropy and volume changes associated with this polyamorphic transformation are positive and negative, respectively, and consequently the corresponding Clapeyron slope for this transition would be negative. This result has far reaching implications in our current understanding of the thermodynamics of polyamorphic transitions in glasses and glass-forming liquids.

42 ENGINEERING↗
DOE OSTI2025

Inspecta Technical Report

Sandia National Laboratories (SNL) has developed Inspecta (International Nuclear Safeguards Personal Examination and Containment Tracking Assistant), an AI-powered smart digital assistant (SDA) equipped with robotic capabilities. This innovative tool aims to enhance the effectiveness, efficiency, and safety of international nuclear safeguards inspections. Inspecta is designed to assist inspectors on-site by supporting or automating tasks that are often mundane, hazardous, or prone to errors. In 2021, the development team established the specifications for Inspecta by thoroughly analyzing International Atomic Energy Agency (IAEA) documents and consulting with former IAEA inspectors and subject matter experts. This process involved aligning in-field inspection tasks with existing commercial and open-source technologies, thereby creating a roadmap for the initial prototype of Inspecta and identifying areas requiring further research and development. From 2022 to 2025, the focus shifted to integrating a critical inspection activity—the examination of seals—into an early version of Inspecta. This phase has involved the development of both software and hardware capabilities essential for this task. This report outlines the advancements in Inspecta’s functionalities, particularly those that support the seal examination process.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2021

Numerical Study and Validation of Melting and Solidification in PCM Embedded Heat Exchangers with Straight Tube

Latent heat thermal energy storage (LHTES) systems have shown great potential to enable reliable use of renewable energy and load shifting. LHTES offer high storage density and release energy at near constant temperature because of its use of phase change materials (PCMs). The cylindrical PCM heat exchangers (PCMHX) are one of the most used technologies due to their simplicity. Numerical models for such PCMHX enable engineers to estimate their performance for different design parameters and operating conditions without having to test them all. However, modeling the phase change phenomena can be challenging. To better understand the difficulties involving accurate modeling of PCMHX, a cylindrical latent storage unit filled with PCM and water as in-tube heat transfer fluid (HTF) is numerically investigated. This paper presents a study based on a 2D-axisymmetric model of a straight tube embedded in PCM in a cylindrical container. CFD is used to study the charging (melting) and discharging (solidification) phenomena. The models are validated against experimental and numerical data from the literature. The predicted local PCM temperature profile over time agrees within 2K compared to the experimental values. The paper also presents a simple method to estimate the melting and solidification phase change temperature range from limited data provided by PCM manufacturers.

PCM, melting, solidification, CFD, heat exchanger↗
DOE OSTI2026

Challenges and Opportunities for HVAC + Phase Change Material Thermal Energy Storage in Buildings

Phase-change material (PCM) thermal-energy storage (TES) integrated with HVAC and domestic hot water (DHW) can shift a large share of building thermal loads. By flattening and shifting loads, PCM TES reduces peak electricity use, eases stress on local and grid infrastructure, and lowers costs. It can also defer costly upgrades to service panels, distribution, and transmission. Higher energy density relative to chilled or hot water storage makes PCM TES practical for small, space limited, and retrofit projects, while packaged HVAC-integrated systems expand cost-effective load shifting to commercial buildings that previously lacked options. Despite this promise, deployment faces barriers. This paper presents challenges, opportunities, and lessons learned from lab and field integrations of PCM TES with packaged HVAC systems. Key challenges include misalignment between default heat pump controls tuned for direct-to-load operation and TES charge/discharge objectives, PCM properties that diverge from manufacturer claims and evolve with cycling, and high integration and deployment costs with off-the-shelf products. These studies underscore the need for factory built, integrated systems that arrive as prepackaged modules with proven controls, reducing design and installation effort and delivering predictable performance across projects. The paper outlines steps to enable viable and scalable PCM TES HVAC and DHW systems, including 1) validated methods that can be used to characterize PCM properties and TES system performance, 2) supervisory controls that optimize charge/discharge scheduling, and 3) factory integrated packaging that eliminates bespoke field engineering.

Dutton, Spencer↗
DOE OSTI2023

First-Principles-Based Machine Learning Models for Phase Behavior and Transport Properties of CO 2

In this work, we construct distinct first-principles-based machine-learning models of CO 2 , reproducing the potential energy surface of the PBE-D3, BLYP-D3, SCAN and SCAN-rvv10 approximations of density functional theory. Here we employ the Deep Potential methodology to develop the models and consequently achieve a significant computational efficiency over ab initio molecular dynamics (AIMD) that allows for larger system sizes and time scales to be explored. Although our models are trained only with liquid phase configurations, they are able to simulate a stable interfacial system and predict vapor-liquid equilibrium properties, in good agreement with results from the literature. Because of the computational efficiency of the models, we are also able to obtain transport properties, such as viscosity and diffusion coefficients. We find that the SCAN-based model presents a temperature shift in the position of the critical point, while the SCAN-rvv10-based model shows improvement but still exhibits a temperature shift that remains approximately constant for all properties investigated in this work. We find that the BLYP-D3-based model generally performs better for liquid phase and vapor-liquid equilibrium properties, but the PBE-D3-based model is better suited for predicting transport properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

CHARGED POINT DEFECTS AND DEFECT COMPLEXES IN PHOSPHORENE AND STRUCTURAL PREDICTION OF TAU-11, A DENSITY FUNCTIONAL THEORY APPROACH

With the advent of powerful computers, first principle calculations have become a robust and reliable tool to complement experiments in the study of materials. First principle calculations such as density functional theory can be used to guide experiments to save time and effort when it comes to new and advanced materials discovery. Study of charge defects in materials and crystal structure prediction are such areas in which density functional theory calculations facilitate the prediction of defect formation energy, charge transition levels and elemental site occupations. Experimentally, studying charge defects requires inferring results from various techniques. Likewise, determining site occupancies for similar elements using experimental techniques is challenging and sometimes impossible. In this work, we study the charged intrinsic and extrinsic defects and defect complexes in phosphorene and determine the site occupancies of Al, Fe and Si in the τ11 phase using density functional theory. In the defect work, we calculate the defect formation energy, charge transition level, binding energies and Stokes shift for vacancy, dopant substitution and dopant-vacancy defect complexes in phosphorene. We found that vacancy defect in phosphorene becomes negatively charged in n-type doping and may passivate the dopants and reduce carrier concentration and mobility. For non-metal dopants in phosphorene, we predict that O, S and Si prefer to form dopant-vacancy complexes removing the vacancy defect states from the band gap. Mn dopant-vacancy defect complex exhibits possibility of switching between two magnetic spin states. Lastly, using density functional theory, we complement the results from neutron powder diffraction to determine the site occupancies of Al and Si in τ11 phase which was used to determine the alloying element to develop a high temperature and low density alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Smaller than Expected Bright-spot Offsets in Spitzer Phase Curves of the Hot Jupiter Qatar-1b

We present Spitzer full-orbit thermal phase curves of the hot Jupiter Qatar-1b, a planet with the same equilibrium temperature—and intermediate surface gravity and orbital period—as the well-studied planets HD 209458b and WASP-43b. We measure secondary eclipse depths of 0.21 ± 0.02% at 3.6 μm and 0.30 ± 0.02% at 4.5 μm, corresponding to dayside brightness temperatures of 1542{sub −31}{sup +32} K and 1557{sub −36}{sup +35} K, respectively, consistent with a vertically isothermal dayside. The respective nightside brightness temperatures are 1117{sub −71}{sup +76} and 1167{sub −74}{sup +69} K, in line with a trend that hot Jupiters all have similar nightside temperatures. We infer a Bond albedo of 0.12{sub −0.16}{sup +0.14} and a moderate day–night heat recirculation efficiency, similar to HD 209458b. General circulation models for HD 209458b and WASP-43b predict that their bright spots should be shifted east of the substellar point by tens of degrees, and these predictions were previously confirmed with Spitzer full-orbit phase curve observations. The phase curves of Qatar-1b are likewise expected to exhibit eastward offsets. Instead, the observed phase curves are consistent with no offset: 11° ± 7° at 3.6 μm and −4° ± 7° at 4.5 μm. The discrepancy in circulation patterns between these three otherwise similar planets points to the importance of secondary parameters like rotation rate and surface gravity, and the presence or absence of clouds, in determining atmospheric conditions on hot Jupiters.

79 ASTRONOMY AND ASTROPHYSICS↗