SEARCH · Engineering Papers
Results for “Particle Size”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Predicting the evolution of biomass bulk density through feedstock preprocessing: Discrete element modeling, regression analysis, and pilot-scale validation
Bulk density is an important material property of biomass feedstocks, influencing handling, storage, transport costs, and conversion efficiency. In this study, predictive regression models for loose and tapped bulk densities of Alamo and Cave-in-Rock switchgrass are developed using a comprehensive dataset generated via calibrated bonded-sphere discrete element method (DEM) simulations. Here, a key contribution of this study is the use of a DEM-based approach, which correlates density with moisture content and particle size distribution parameters and enables analysis across a continuous particle size range, overcoming limitations of purely experimental data. For comparison, regression models are also developed using only experimental data from pilot-scale runs at the Biomass Feedstock National User Facility at Idaho National Laboratory. Validation against pilot-scale data showed reasonable prediction accuracy for both model types, particularly for smaller particle sizes (post-secondary grinding). While the experimental model showed slightly better performance matching the validation data in some cases, the DEM-based model benefits from a much larger dataset, reduced predictor multicollinearity, and continuous parameter coverage, highlighting the utility of validated simulation models for developing robust predictive tools for biomass preprocessing applications.
Dustsonde measurements of the Mount St. Helens volcanic dust cloud over Wyoming
Numerous balloon soundings of the aerosol and condensation nuclei (CN) concentrations were made over Laramie, Wyoming following the eruption of Mount St. Helens in May of 1980. On several occasions the volatility of the particles was tested. In addition, special instrumentation was used to observe the evolution of particle size after the eruption. The particles in the initial cloud were relatively large and nonvolatile. In a relatively short time, however, the aerosol began showing a dominant volatile component. Although there were probably no CN in the original cloud due to the expected very short coagulation life time, high concentrations of unusually small CN particles were observed about a month after the eruption. By the end of September the CN profiles and associated particle size were practically back to normal. At present the aerosol particles show about a three times larger concentration than before the eruption, most of the new material being in a layer centered around 19 km. The net effect of the more recent series of eruptions during the last half of October 1980 seems to be negligible.
Using Observations of Deep Convective Systems to Constrain Atmospheric Column Absorption of Solar Radiation in the Optically Thick Limit
Atmospheric column absorption of solar radiation A(sub col) is a fundamental part of the Earth's energy cycle but is an extremely difficult quantity to measure directly. To investigate A(sub col), we have collocated satellite-surface observations for the optically thick Deep Convective Systems (DCS) at the Department of Energy Atmosphere Radiation Measurement (ARM) Tropical Western Pacific (TWP) and Southern Great Plains (SGP) sites during the period of March 2000 December 2004. The surface data were averaged over a 2-h interval centered at the time of the satellite overpass, and the satellite data were averaged within a 1 deg X 1 deg area centered on the ARM sites. In the DCS, cloud particle size is important for top-of-atmosphere (TOA) albedo and A(sub col) although the surface absorption is independent of cloud particle size. In this study, we find that the A(sub col) in the tropics is approximately 0.011 more than that in the middle latitudes. This difference, however, disappears, i.e., the A(sub col) values at both regions converge to the same value (approximately 0.27 of the total incoming solar radiation) in the optically thick limit (tau greater than 80). Comparing the observations with the NASA Langley modified Fu_Liou 2-stream radiative transfer model for optically thick cases, the difference between observed and model-calculated surface absorption, on average, is less than 0.01, but the model-calculated TOA albedo and A(sub col) differ by 0.01 to 0.04, depending primarily on the cloud particle size observation used. The model versus observation discrepancies found are smaller than many previous studies and are just within the estimated error bounds. We did not find evidence for a large cloud absorption anomaly for the optically thick limit of extensive ice cloud layers. A more modest cloud absorption difference of 0.01 to 0.04 cannot yet be ruled out. The remaining uncertainty could be reduced with additional cases, and by reducing the current uncertainty in cloud particle size.
Evaluation of GEOS Aerosols Using CAMP2Ex Observations
Biomass burning aerosol impacts aspects of the atmosphere and Earth system through direct and semi-direct effects, as well as influencing air quality. Despite its importance, the representation of biomass burning aerosol is not always accurate in numerical weather prediction and climate models or reanalysis products. Using observations collected as part of the Cloud, Aerosol and Monsoon Processes Philippines Experiment (CAMP2Ex) in August through October of 2019, aerosol concentration and optical properties are evaluated within the Goddard Earth Observing System (GEOS) and its underlying aerosol module, GOCART. In the operational configuration, GEOS assimilates aerosol optical depth observations at 550 nm from AERONET and MODIS to constrain aerosol fields. Particularly for biomass burning aerosol, without the assimilation of aerosol optical depth, aerosol extinction is underestimated compared to observations collected in the Philippines region during the CAMP2Ex campaign. The assimilation process adds excessive amounts of carbon to account for the underestimated extinction, resulting in positive biases in the mass of black and organic carbon, especially within the boundary layer, relative to in situ observations from the Langley Aerosol Research Group Experiment. Counteracting this, GEOS is deficient in sulfate and nitrate aerosol just above the boundary layer. Aerosol extinction within GEOS is a function of the mass of different aerosol species, the ambient relative humidity, the assumed spectral optical properties, and particle size distribution per species. The relationship between dry and ambient extinction in GEOS reveals that hygroscopic growth is too high within the model for biomass burning aerosol. An additional concern lies in the assumed particle size distribution for GEOS, which has a single mode radius that is too small for organic carbon. Variability in the observed particle size distribution for biomass burning aerosol within a single flight also illuminates the fact that a single assumed particle size distribution is not sufficient and that for a proper representation, a more advanced aerosol module within GEOS may be necessary.
Estimate of the temperature rise of micron- sized silver particles in the electron microscope due to electron-beam heating.
Temperature rise of micron sized silver particles on carbon film due to electron beam heating, setting up heat balance equation
Effects of the method of active site characterization for determining structure-sensitivity in Ag-catalyzed ethylene epoxidation
We report catalysts have been prepared on a low surface area α-Al 2 O 3 support used commercially for previous generation olefin epoxidation catalysts. Prescreening of the low surface area alumina (0.73 m 2 /g) indicated the absence of acid catalyzed isomerization of EO at an evaluation temperature of 210 °C. A 0.1 wt% Ag base material synthesized by incipient wetness impregnation of AgNO 3 was used as a base material for electroless deposition (ED) of additional Ag to increase particle sizes by controlled reduction of Ag + directly onto the preexisting Ag surface to form weight loadings between 0.3 and 5.0 wt% metal. A 12 wt% Ag/α-Al 2 O 3 using Ag 2 C 2 O 4 as the Ag precursor was also prepared to compare performance of the ED samples with a catalyst more typical of industrial formulations. Characterization by SEM, STEM, and hydrogen titration of oxygen precovered Ag characterized before and after catalytic evaluation indicated that microscopy is required to accurately represent distributions of Ag particle sizes, but H 2 titration of O-precovered Ag gives the best representation of active sites since it directly counts the number of Ag surface sites. Larger particles >100 nm are resistant to both Ag sintering and carbon foulant; TOF values were relatively insensitive to particle size with only a 2.2 × difference between the best and worst performing samples. Selectivity, which is not a function of TOF, shows the most significant structure sensitivity effect where particle sizes follow the trend 67 nm ≈ 92 nm (58% EO) < 157 nm (67% EO) < 211–542 nm (73% EO). The lower EO selectivities were also correlated with increased fouling for the smaller Ag sizes, suggesting that more strongly bound EO precursor(s) leads to combustion and CO 2 /H 2 O formation.
Study of the thermal degradation mechanism of a composite propellant
The current experimental program was designed to systematically investigate the role of the oxidizer in the thermal degradation process of composite propellants. The scanning electron microscope (SEM) was used to examine the failure sites in thermally degraded propellant samples. The formulation variables tested were oxidizer purity, oxidizer particle size, and oxidizer to binder bonding agent. The binder, a saturated hydrocarbon, was kept constant throughout the experiments. The oxidizers were: AP, chlorate-doped AP, arsenate-doped AP, and phosphate-doped AP. The oxidizer particle size distribution was 60% of the large fraction and 40% of the small fraction. The bonding agent, when present, was used at the 0.15% level. The data showed that both the oxidizer purity and particle size had an important affect on the thermal degradation process. The affect of the oxidizer particle size was more noticeable at the higher temperature and stress levels. An examination of the failure site, by SEM, of propellants subject to these latter conditions indicated that the fracturing of the large oxidizer particles led to the propellant cracking.
Smart Preprocessing & Robust Integration Emulator
To achieve the desired particle size of biomass feedstocks during preprocessing for trouble-free handling and conversion to produce biofuels and bioproducts, the raw materials must undergo a crucial milling process. The particle size of biomass plays a critical role in subsequent biofuel manufacturing, where a larger area-to-volume ratio facilitates efficient synthesis while balancing the impact of moisture on biomass storage. To optimize biofuel production efficiency and overcome these challenges, it is imperative to accurately predict the particle size distribution (PSD) of the biomass in the design of efficient preprocessing systems. The population balance model (PBM), upon empirical calibration and validation, can provide rapid prediction of post-milling PSD of granular biomass. However, PSD has limitations related to mass conservation and the absence of moisture considerations. To overcome these drawbacks, a deep learning model called the enhanced deep neural operator (DNO+) is implemented in the code. This model not only retains the capabilities of the PBM in handling complex mapping functions but also incorporates additional factors influencing the system. By considering various experimental conditions such as sieve size and moisture content, the trained DNO+ model can effectively predict the PSD after milling for any given feed PSD. To further reduce the reliance on experimental data, the PBM is integrated into the DNO+ model, resulting in a physics-informed DNO+ (PIDNO+). The PIDNO+ model addresses the non-conservation of quality exhibited by the PBM while inheriting the advantages of the DNO+ model in considering multiple influencing factors. Moreover, the PIDNO+ model significantly reduces the amount of data required for model training. Both deep learning models, i.e., DNO+ and PIDNO+, are excellent in predictive performance, offering swift and accurate machine learning-based predictions. The use of this code that contains these models will assist in guiding the proper milling equipment selection and operational conditions to achieve the desired biomass particle sizes, ensuring the efficiency of subsequent biofuel and bioproduct production processes.
Impact of environmental attributes on the uncertainty in MAIAC/MODIS AOD retrievals: A comparative analysis
This work examines the impact of different environmental attributes on the uncertainty in satellite-based Aerosol Optical Depth (AOD) retrieval against the benchmark Aerosol Robotic Network (AERONET) AOD measurements at 21 sites across North Africa, California and Germany, in the years 2007–2017. As a first step, we studied the effects of spatial averaging the Multi-Angle Implementation of Atmospheric Correction (MAIAC) AOD retrievals, and of temporal averaging the AERONET AOD around the satellite (Aqua) overpass, on the agreement between the two products. AERONET AOD averaging over a time-window of ±15 min around the satellite overpass and the 1 ×1 km2 spatial grid of MAIAC were found to provide the best AOD retrieval performance. Next, MAIAC AOD were stratified according to different co-measured environmental attributes (aerosol loading, dominant particle size, vegetation cover, and prevailing particle type) and analyzed against the AERONET AOD. The envelope of the expected retrieval error varied considerably among different environmental attributes categories, with more accurate AOD retrievals obtained over highly vegetated areas (i.e. less surface reflectance) than over arid areas. Moreover, the retrieval accuracy was found to be sensitive to the aerosol loading and particle size, with a large bias between the MAIAC and AERONET AOD during high aerosol loading of coarse particles. In addition, the retrieval accuracy of MAIAC AOD was found to depend on the aerosol type due to the aerosol model assumptions regarding their optical properties.
Asymptotic Solutions for Optical Properties of Large Particles with Strong Absorption
For scattering calculations involving nonspherical particles such as ice crystals, we show that the transverse wave condition is not applicable to the refracted electromagnetic wave in the context of geometric optics when absorption is involved. Either the TM wave condition (i.e., where the magnetic field of the refracted wave is transverse with respect to the wave direction) or the TE wave condition (i.e., where the electric field is transverse with respect to the propagating direction of the wave) may be assumed for the refracted wave in an absorbing medium to locally satisfy the electromagnetic boundary condition in the ray tracing calculation. The wave mode assumed for the refracted wave affects both the reflection and refraction coefficients. As a result, a nonunique solution for these coefficients is derived from the electromagnetic boundary condition. In this study we have identified the appropriate solution for the Fresnel reflection/refraction coefficients in light scattering calculation based on the ray tracing technique. We present the 3 x 2 refraction or transmission matrix that completely accounts for the inhomogeneity of the refracted wave in an absorbing medium. Using the Fresnel coefficients for an absorbing medium, we derive an asymptotic solution in an analytical format for the scattering properties of a general polyhedral particle. Numerical results are presented for hexagonal plates and columns with both preferred and random orientations. The asymptotic theory can produce reasonable accuracy in the phase function calculations in the infrared window region (wavelengths near 10 micron) if the particle size (in diameter) is on the order of 40 micron or larger. However, since strong absorption is assumed in the computation of the single-scattering albedo in the asymptotic theory, the single scattering albedo does not change with variation of the particle size. As a result, the asymptotic theory can lead to substantial errors in the computation of single-scattering albedo for small and moderate particle sizes. However, from comparison of the asymptotic results with the FDTD solution, it is expected that a convergence between the FDTD results and the asymptotic theory results can be reached when the particle size approaches 200 micron. We show that the phase function at side-scattering and backscattering angles is insensitive to particle shape if the random orientation condition is assumed. However, if preferred orientations are assumed for particles, the phase function has a strong dependence on scattering azimuthal angle. The single-scattering albedo also shows very strong dependence on the inclination angle of incident radiation with respect to the rotating axis for the preferred particle orientations.
Investigation into the crystal structure–dielectric property correlation in barium titanate nanocrystals of different sizes
For high capacitance multilayer ceramic capacitors, high dielectric constant and lead-free ceramic nanoparticles are highly desired. However, as the particle size decreases to a few tens of nanometers, their dielectric constant significantly decreases, and the underlying mechanism has yet to be fully elucidated. Herein, we report a systematic investigation into the crystal structure–dielectric property relationship of combustion-made BaTiO 3 (BTO) nanocrystals. When the nanocrystal size was 100 nm and below, a metastable paraelectric cubic phase was found in the as-received BTO (denoted as arBTO) nanocrystals based on an X-ray diffraction (XRD) study. A stable ferroelectric tetragonal phase was present when the nanocrystal size was above 200 nm. Notably, the cubic arBTO (particle size ≤100 nm) exhibited tetragonal fluctuations as revealed by Raman spectroscopy, whereas the tetragonal arBTO (particle size ≥200 nm) contained ~10% cubic fraction according to the Rietveld fitting of the XRD profiles. Thermal annealing of the multi-grain tetragonal arBTO at 950 °C yielded single crystals of annealed BTO (denoted as anBTO), whose dielectric constants were higher than those of arBTO. However, the single crystalline anBTO prevented the formation of 90° domains; therefore, they exhibited a low dielectric constant of ~300. Although X-ray photoelectron spectroscopy and high-resolution transmission electron microscopy could not identify the exact structural defects, our study revealed that surface and bulk defects formed during synthesis affect the final crystal structures and thus the dielectric properties of BTO nanocrystals with different sizes. Finally, the understanding obtained from this study will help us design high dielectric constant perovskite nanocrystals for next-generation multilayer ceramic capacitor applications.
Comparisons of Bin and Bulk Microphysics Schemes in Simulations of Topographic Winter Precipitation with Radar and Radiometer Measurements
The Hebrew University Cloud Model (HUCM) bin scheme and the Thompson bulk scheme in the Weather Research and Forecasting (WRF) model are compared to assess biases often found in simulated brightness temperature and radar reflectivity. Compared to our preceding study that evaluated several bulk schemes in the WRF model, the current study obtains a reduction of the bias from excessive microwave scattering by precipitation ice for both HUCM bin and the Thompson bulk microphysics schemes for a topographic winter precipitation event associated with an atmospheric river. The Thompson particle size distributions (PSDs) and snow particle density assumption are implemented into the Goddard Satellite Data Simulator Unit (G‐SDSU) and have produced improvements. Despite the greater sophistication of the bin scheme in representing cloud and precipitation processes, the simulation with the Thompson bulk scheme is generally in better agreement with observations for this winter event. The explicitly resolved hydrometeor PSDs in HUCM enable analysis of mass spectra variations in response to changes in microphysics assumptions. Two HUCM sensitivity runs tested the enhancement of snow particle breakup and the influence of ice nuclei (IN) concentration. Higher IN concentration resulted in increased snow mass and broadened the spectrum toward small‐size particles. Modified snow mass spectra and resultant changes in graupel contributed to modifications in scattering and reflectivity simulations. The article demonstrates the bin scheme's capability to provide a new means to improve our understanding of uncertainties in mesoscale weather models and radiative transfer models.
Snow Microphysical Retrieval from the NASA D3R Radar During ICE-POP 2018
A method is developed to use both polarimetric and dual-frequency radar measurements to retrieve microphysical properties of falling snow. It is applied to the Ku- and Ka-band measurements of the NASA dual-polarization, dual-frequency Doppler radar (D3R) obtained during the International Collaborative Experiments for PyeongChang 2018 Olympic and Paralympic winter games (ICE-POP 2018) field campaign and incorporates the Atmospheric Radiative Transfer Simulator (ARTS) microwave singles cattering property database for oriented particles. The retrieval uses optimal estimation to solve for several parameters that describe the particle size distribution (PSD), relative contribution of pristine, aggregate, and rimed ice species, and the orientation distribution along an entire radial simultaneously. Examination of Jacobian matrices and averaging kernels shows that the dual-wavelength ratio (DWR) measurements provide information regarding the characteristic particle size, and to a lesser extent, the rime fraction and shape parameter of the size distribution, whereas the polarimetric measurements provide information regarding the mass fraction of pristine particles and their characteristic size and orientation distribution. Thus, by combining the dual-frequency and polarimetric measurements, some ambiguities can be resolved that should allow a better determination of the PSD and bulk microphysical properties (e.g., snowfall rate) than can be retrieved from single-frequency polarimetric measurements or dual-frequency, single-polarization measurements. The D3R ICE-POP retrievals were validated using Precipitation Imaging Package (PIP) and Pluvio weighing gauge measurements taken nearby at the May Hills ground site. The PIP measures the snow PSD directly, and its measurements can be used to derived the snowfall rate (volumetric and water equivalent), mean volume-weighted particle size, and effective density, as well as particle aspect ratio and orientation. Four retrieval experiments were performed to evaluate the utility of different measurement combinations: Kuonly, DWR-only, Ku-pol, and All-obs. In terms of correlation, the volumetric snowfall rate (r D 0:95) and snow water equivalent rate (r D 0:92) were best retrieved by the Ku-pol method, while the DWR-only method had the lowest magnitude bias for these parameters (-31% and -8 %, respectively). The methods that incorporated DWR also had the best correlation to particle size (r D 0:74 and r D 0:71 for DWR-only and All-obs, respectively), although none of the methods retrieved density particularly well (r D 0:43 for Allobs). The ability of the measurements to retrieve mean aspect ratio was also inconclusive, although the polarimetric methods (Ku-pol and All-obs) had reduced biases and mean absolute error (MAE) relative to the Ku-only and DWR-only methods. The significant biases in particle size and snowfall rate appeared to be related to biases in the measured DWR, emphasizing the need for accurate DWR measurements and frequent calibration in future D3R deployments.
Cometary Activity Begins at Kuiper Belt Distances: Evidence from C/2017 K2
We study the development of activity in the incoming long-period comet C/2017 K2 over the heliocentric distance range 9 ≲ r {sub H} ≲ 16 au. The comet continues to be characterized by a coma of submillimeter-sized and larger particles ejected at low velocity. In a fixed co-moving volume around the nucleus we find that the scattering cross section of the coma, C, is related to the heliocentric distance by a power law, C∝r{sub H}{sup -s}, with heliocentric index s = 1.14 ± 0.05. This dependence is significantly weaker than the r {sub H} {sup -2} variation of the insolation as a result of two effects. These are, first, the heliocentric dependence of the dust velocity and, second, a lag effect due to very slow-moving particles ejected long before the observations were taken. A Monte Carlo model of the photometry shows that dust production beginning at r {sub H} ~ 35 au is needed to match the measured heliocentric index, with only a slight dependence on the particle size distribution. Mass-loss rates in dust at 10 au are of order 10{sup 3} kg s{sup -1}, while loss rates in gas may be much smaller, depending on the unknown dust to gas ratio. Consequently, the ratio of the nongravitational acceleration to the local solar gravity, α', may, depending on the nucleus size, attain values of ~10{sup -7} ≲ α' ≲ 10{sup -5}, comparable to values found in short-period comets at much smaller distances. Nongravitational acceleration in C/2017 K2 and similarly distant comets, while presently unmeasured, may limit the accuracy with which we can infer the properties of the Oort cloud from the orbits of long-period comets.
Development of New Lunar Highland Regolith Simulant, NUW-LHT-5M
Introduction: NASA has a need for large quantities of lunar simulants that closely match future manned lunar missions at landing sites near the Lunar South Pole. The current simulant was designed to approximate NU-LHT-2M, and -4M, except using natural minerals and a fully synthetic, non-basaltic, high calcium glass. Washington Mills in Niagara Falls, NY was contracted to produce this new simulant due to their electric arc furnace (EAF) fusion technology and capabilities for crushing and sizing ceramics. The primary objectives of this work were: (1) to create a commercially produced simulant that contains a high fidelity, high calcium (An90+), low Mg/Fe glass without basaltic constituents; (2) to create a simulant that uses existing, terrestrially mined, and readily available minerals blended with a synthetic glass, and (3) accomplish objectives (1) and (2) using conventional processing methods capable of production levels that can meet substantial current and future demands of NASA projects. Another consideration was that highland simulants closest to meeting these requirements, NU-LHT-2M and -4M types, are out of production and largely out of stock. Design: The design chosen for development and production for this work is NU-LHT-2M, de-signed by Doug Stoeser and Douglas Rickman, which uses Stillwater anorthosite and norite rocks and synthetic glass. The composition targeted the average composition, glass content and particle size distribution of Apollo 16 samples [1]. The design utilizes two Stillwater minerals, anorthosite (37.7 wt.%), norite (17.6 wt.%), a commercially sourced olivine (4.7 wt.%), and a synthetic glass (40 wt.%). Processing: Stillwater rocks were hand collected and initially crushed by the USGS. Further crushing and milling was performed at Washing-ton Mills. For the glass, oxides were blended in the ap-propriate ratios, blended in a v-blender, and placed in a graphite lined, water cooled pot. The mixture was fused in Washington Mills’ pilot scale, 500 kW EAF. The molten glass was then poured into water and quenched to inhibit crystallization. Several pour/quench cycles were required to produce the total quantity of glass needed. Anorthosite, norite and olivine were milled together to the target particle size in a ball mill. The glass was ball milled separately. The complete simulant was produced by blending the milled materials. Particle size distribution, phase and chemical analyses of the materials was were per-formed at Washington Mills. Results: The glass composition was found to match the Apollo 16 oxide content average [1] quite well, with the exception of SiO2 and Fe2O3. The deviation of SiO2 and Fe2O3 from batched content was believed to be due to limitations inherent in the use of the arc furnace technique for these types of materials. A particle size distribution of the full simulant formulation closely matching the average for the Apollo 16 samples was also achieved. Fig. 1 shows the morphology of the final simulant particles. The size distribution is compared to the target in Fig. 2. Conclusions: A new lunar highlands type simulant containing a high-quality synthetic glass, closely matching an average composition of the Apollo 16 regolith was produced. Processing utilized easily scalable mineral and glass making methods.
Airborne Aerosol Closure Studies During PRIDE
The Puerto Rico Dust Experiment (PRIDE) was conducted during June/July of 2000 to study the properties of Saharan dust aerosols transported across the Atlantic Ocean to the Caribbean Islands. During PRIDE, the NASA Ames Research Center six-channel (380 - 1020 nm) airborne autotracking sunphotometer (AATS-6) was operated aboard a Piper Navajo airplane alongside a suite of in situ aerosol instruments. The in situ aerosol instrumentation relevant to this paper included a Forward Scattering Spectrometer Probe (FSSP-100) and a Passive Cavity Aerosol Spectrometer Probe (PCASP), covering the radius range of approx. 0.05 to 10 microns. The simultaneous and collocated measurement of multi-spectral aerosol optical depth and in situ particle size distribution data permits a variety of closure studies. For example, vertical profiles of aerosol optical depth obtained during local aircraft ascents and descents can be differentiated with respect to altitude and compared to extinction profiles calculated using the in situ particle size distribution data (and reasonable estimates of the aerosol index of refraction). Additionally, aerosol extinction (optical depth) spectra can be inverted to retrieve estimates of the particle size distributions, which can be compared directly to the in situ size distributions. In this paper we will report on such closure studies using data from a select number of vertical profiles at Cabras Island, Puerto Rico, including measurements in distinct Saharan Dust Layers. Preliminary results show good agreement to within 30% between mid-visible aerosol extinction derived from the AATS-6 optical depth profiles and extinction profiles forward calculated using 60s-average in situ particle size distributions and standard Saharan dust aerosol refractive indices published in the literature. In agreement with tendencies observed in previous studies, our initial results show an underestimate of aerosol extinction calculated based on the in situ size distributions relative to the extinction obtained from the sunphotometer measurements. However, a more extensive analysis of all available AATS-6 and in situ size distribution data is necessary to ascertain whether the preliminary results regarding the degree of extinction closure is representative of the entire range of dust conditions encountered in PRIDE. Finally, we will compare the spectral extinction measurements obtained in PRIDE to similar data obtained in Saharan dust layers encountered above the Canary Islands during ACE-2 (Aerosol Characterization Experiment) in July 1997. Thus, the evolution of Saharan dust spectral properties during its transport across the Atlantic can be investigated, provided the dust origin and microphysical properties are found to be comparable.
SOC Synthetic Microstructure Bank
QUICK START: Start with property_library.html (can be found by typing the filename into the query box) and use the interactive table to filter, sort, and select a microstructure with the desired properties. Search for the alphabetic code to obtain the corresponding dataset. Full description: This is a bank of 1,970 unique 3-phase electrode microstructure files. When you account for reassigning phase IDs (e.g. declare that 1=Ni and 2=pore, instead of 1=pore and 2=Ni), it actually represents 5,910 unique electrode microstructures, each of which could be considered to be either an air or a fuel electrode (e.g. declare that the phase IDs correspond to pore, Ni, and YSZ; or that they correspond to pore, LSCF, and GDC; or whatever electron-conductor and ion-conductor combination is being studied). The voxel size is 50 nm and each electrode file contains a 4x4 grid of (12.5 micron)^3 sub-volumes. If placed together in a grid, they comprise a 50x50x12.5 micron electrode (note that the interfaces between sub-volumes will be sharp; this can be mitigated via simulating annealing/relaxation). The sub-volumes can also be used individually for a reasonably sized 12.5 micron cubic region-of-interest. A user can simply consider the voxel size to be a different value to rescale the volumes (and all of their morphological features, including particle size) as desired. These microstructures were generated using DREAM3D. The general procedure is outlined in https://doi.org/10.1016/j.jpowsour.2018.03.025 The file names are an alphabetic code having to do with the input parameters used in DREAM3D when they were generated. Most users would be best served by starting with the file property_library.html or property_library_subvols.html (which lists properties for each individual subvolume). These files contain a catalogue of the actual, measured properties of every microstructure in the database. Any combination of property values can be filtered and sorted until a desired electrode is found, at which point the user can find the file corresponding to that alphabetic code. The properties in the catalogue include connected TPB density, and for each phase: phase fraction, average particle size, polydispersity of particle size, tortuosity, and connected pair-wise interfacial area. They also include what fraction of each property is connected through to the interfaces of the volume. If the desired combination of properties is not found at first, remember that the phase IDs can be re-assigned arbitrarily, e.g. swapping 1s and 2s. In fact, the database was generated with this in mind so as not to generate redundant microstructures. If the database does not contain the desired property combinations, try to search for the other possible permutations of those properties with re-assigned phase IDs. Please cite https://doi.org/10.1149/10301.0909ecst for use. Please contact the maintainer, William K. Epting, for additional information or assistance.