Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PIN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Fly-away restraint pin mechanism for the Army's PATRIOT missile system

The development of the longitudinal restraint mechanism for the PATRIOT missile system is reviewed. Two approaches for the restraint pin design are discussed: an initial ordnance mechanism, and a passive fly-away mechanism. Because of reliability problems and a desire to reduce cost the fly-away restraint mechanism was chosen.

Knight, F. W.↗

Stress intensities for cracks emanating from pin-loaded holes

A series of stress freezing photoelastic experiments were conducted on large plates containing central holes with cracks emanating from the edge formed by the intersection of the hole with the plate surface. Loads were applied through rigid pins with neat fits in the holes. Stress-intensity factors (SIF) were estimated by a computer assisted least squares analysis of the photoelastic data taken from slices near the points of intersection of the flaw border with the hole boundary and the plate surface. Results indicate that the local mode of loading changes from Mode 1 near the hole boundary to mixed mode near the plate surface. The analysis is extended to include mixed mode loading, and results are compared with an existing approximate theory.

Smith, C. W.↗

Wear of aluminum and hypoeutectic aluminum-silicon alloys in boundary-lubricated pin-on disk sliding

The friction and wear of pure aluminum and a number of hypoeutectic aluminum-silicon alloys (with 3 to 12 wt %Si) were studied with a pin-on-disk apparatus. The contacts were lubricated with mineral oil and sliding was in the boundary-lubrication regime at 2.6 cm/sec. Surfaces were analyzed with photomicrographs, scanning electron microscopy, X-ray dispersive analysis, and diamond pyramid hardness measurements. There were two wear regimes for the alloys - high and low - whereas pure aluminum exhibited a high wear rate throughout the test period. Wear rate decreased and the transition stress from high to low wear increased with increasing hardness. There was no correlation between friction coefficient and hardness. A least squares curve fit indicated a wear-rate dependence greater than the inverse first power of hardness. The lower wear rates of the alloys may be due to the composites of silicon platelets in aluminum resulting in increased hardness and thus impairing the shear of the aluminum.

Ferrante, J.↗

Stress-concentration factors for finite orthotropic laminates with a pin-loaded hole

Stresses were calculated for finite size orthotropic laminates loaded by a frictionless steel pin in a circular hole of the same diameter. The calculations were based on finite element analyses for six laminates. Stress concentration factors, based on nominal bearing stress, were determined for wide ranges of the ratios of width to diameter, w/d and edge distance to diameter, e/d. An infinite laminate case was analyzed for each laminate. Orthotropy had a significant influence on the tensile stress concentration at the hole. For example, the stress concentration factors for the infinite laminate cases ranged from 0.82 to 2.16, compared with 0.87 for the quasi-isotropic laminate. The finite widths and edge distances strongly influenced the tensile stress concentration. For the practical range w/d or = 3, the peak tensile stresses were as much as 80% larger than the infinite laminate reference value. For e/d or = 3, these stresses were amplified by as much as 50%. In contrast, the finite width and edge distance had little effect on shear-out and bearing stress concentrations.

Crews, J. H., Jr.↗

Giant glitches and pinned vorticity in the Vela and other pulsars

Previously unexamined regularities in the Vela pulsar timing data are noted, and explained by a theory of giant glitches in the Vela and other pulsars as the dynamic consequence of catastrophic unpinning events in the pinned crustal neutron superfluid. Postglitch behavior then results from the glitch-induced vortex creep. An implication of the theory is that the energy release in this glitch scenario need not appear instantaneously on the surface as heat.

Alpar, M. A.↗

Wire Retrieves Broken Pin

Safety wire retains pieces of broken tool. Retrieval wire running through shaft of tool used to pull pieces of tool out of hole, should tool break during use. Safety wire concept suitable for pins subject to deflection or breakage.

Burow, G. H.↗

Measuring Recessed Pins

Sleeve-and-rod-tool measures distances in blind locations. Developed for measuring small distance from top of pin to body holding it.

Kostas, C.↗

Stresses in a quasi-isotropic pin loaded connector using photoelasticity

Birefringent glass-epoxy and a numerical stress separation scheme are used to compute the stresses in the vicinity of a pin-loaded hole. The radial and circumferential stresses at the hole edge, and the net section and shear-out stresses are computed. The numerical and experimental results are compared with the computed stresses. The fixture used to load the connector is discussed and typical isochromatic and isoclinic fringe patterns are presented. The stress-separation scheme is briefly discussed.

Hyer, M. W.↗

Stresses in a quasi-isotropic pin-loaded connector using photoelasticity

Birefringent glass-epoxy and a numerical stress separation scheme are used to compute the stresses in the vicinity of a pin-loaded hole. The radial and circumferential stresses at the hole edge, and the net section and shear-out stresses are computed. The numerical and experimental results are compared with the computed stresses. The fixture used to load the connector is discussed and typical isochromatic and isoclinic fringe patterns are presented. The stress-separation scheme is briefly discussed. Previously announced in STAR as N83-33220

Hyer, M. W.↗

Stresses in pin-loaded orthotropic plates using photoelasticity

The stresses in transparent glass-epoxy plates loaded by a steel pin through a hole were determined by photoelasticity. The stresses around the hole edge, across the net section, along the shear out line, and on the centerline below the hole for quasiisotropic, unidirectional, and angle ply plates are outlined. Stresses in an isotropic comparison specimen are also presented. Stress concentration factors for several locations around the plates are tabulated. The experimental apparatus and the experimental technique are discussed. The isochromatic and isoclinic fringe patterns for the four plates are shown. A description of the necessary photoelastic theory is appended.

Hyer, M. W.↗

Radiation effects induced in pin photodiodes by 40- and 85-MeV protons

PIN photodiodes were bombarded with 40- and 85-MeV protons to a fluence of 1.5 x 10 to the 11th power p/sq cm, and the resulting change in spectral response in the near infrared was determined. The photocurrent, dark current and pulse amplitude were measured as a function of proton fluence. Changes in these three measured properties are discussed in terms of changes in the diode's spectral response, minority carrier diffusion length and depletion width. A simple model of induced radiation effects is presented which is in good agreement with the experimental results. The model assumes that incident protons produce charged defects within the depletion region simulating donor type impurities.

Becher, J.↗

Waveguide PIN junction electrooptic phase modulators Theoretical analysis and design criteria

Basic design equations for waveguide PIN heterojunction electrooptic phase modulators utilizing the linear electrooptic effect are derived, and criteria for optimum operation (in terms of obtainable phase shifts) are discussed. Although the numerical examples pertain to devices fabricated of the AlGaAs system on (100) substrates, the same method can be directly applied to modulators fabricated of other materials.

Marshall, W. K.↗

Finite-Element Fracture Analysis of Pins and Bolts

Stress intensities calculated in bending and tension. Finite-element stress-analysis method gives stress-intensity estimates for surface flaws on smooth and threaded round bars. Calculations done for purely tensile and purely bending loads. Results, presented in dimensionless form, useful for determining fatigue lives of bolts and pins.

Nord, K. J.↗

PIN photodiodes irradiated with 40- and 85-MeV protons

PIN photodiodes were bombarded with 40- and 85-MeV protons to a fluence of 1.5 x 10 to the 11th p/sq cm, and the resulting change in spectral response in the near infrared was determined. The photocurrent, dark current, and pulse amplitude were measured as a function of proton fluence. Changes in these three measured properties are discussed in terms of changes in the diode's spectral response, minority carrier diffusion length, and depletion width. A simple model of induced radiation effects is presented which is in good agreement with the experimental results. The model assumes that incident protons produce charged defects within the depletion region simulating donor type impurities.

Reft, C. S.↗

CdTe and ZnTe metal interface formation and Fermi-level pinning

Interfacial morphology and Fermi-level pinning behavior at the interfaces of Al, Ag, and Pt with UHV-cleaved CdTe and ZnTe are studied using X-ray photoelectron and ultraviolet photoemission spectroscopies. Results are compared to metal/HgCdTe interface formation. For Al/CdTe, a case is found where significantly greater intermixing occurs in CdTe than seen on HgCdTe. The Al/ZnTe interface is also more abrupt than Al/CdTe. Band bending results for interfaces of all three metals with p-CdTe and p-ZnTe are presented and implications for metal/HgZnTe interface formation are considered.

Wahi, A. K.↗

Multi-Pinned-Phase Charge-Coupled Device

Multi-pinned-phase (MPP) technology allows charge-coupled device (CCD) to operate totally inverted during both integration and readout while maintaining other performance characteristics. MPP-CCD made with positive doping implants defining barrier phases. When all phases biased together into inversion, dark current reduced, and potential of charge-collecting wells is difference between potentials of barrier and collection phases. Advantages include complete elimination of residual image effects during integration and readout, low pixel nonuniformity, and increase in quantum efficiency in near infrared because higher operating temperatures used. More tolerant to ionizing radiation environments.

Janesick, James R.↗

Open pinned-phase CCD technology

A novel CCD technology, open pinned-phase (OPP) technology, is presented. Particular attention is given to the design and process features of an OPP-CCD that unite multi- and virtual-phase technologies. It is found that the OPP/CCD will produce a modest short-wavelength QE and excellent charge collection efficiency characteristics which are similar to those of the virtual-phase CCD. However, expensive processes related to thinning, backside accumulation, and packaging are not required in the present case.

Janesick, James↗

Proton radiation effects on multi-pinned-phased CCDs

Three Tektronix 1024 x 1024 multi-pinned-phased (MPP) charge coupled devices were irradiated with protons to obtain data on CCD performance degradation in a proton radiation environment. The devices were irradiated with a spectrum of energies up to 120 MeV, simulating the total radiation dose of a long-term space experiment. Basic parameters such as charge transfer efficiency, dark current, noise, and full well were measured before and after irradiation. A test was also performed to determine the effectiveness of various thicknesses of tantalum shielding in protecting the CCD from damage. Dark current increase and CTE degradation were the most noticeable effects of proton radiation. This paper will present the objectives, test data, and conclusions of the proton testing, and will identify future testing to be performed.

Murata-Seawalt, D.↗