Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Materials Compatibility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Fluoride Salt-Cooled High-Temperature Reactor Technology Development and Demonstration Roadmap

Fluoride salt-cooled High-temperature Reactors (FHRs) are an emerging reactor class with potentially advantageous performance characteristics, and fully passive safety. This roadmap describes the principal remaining FHR technology challenges and the development path needed to address the challenges. This roadmap also provides an integrated overview of the current status of the broad set of technologies necessary to design, evaluate, license, construct, operate, and maintain FHRs. First-generation FHRs will not require any technology breakthroughs, but do require significant concept development, system integration, and technology maturation. FHRs are currently entering early phase engineering development. As such, this roadmap is not as technically detailed or specific as would be the case for a more mature reactor class. The higher cost of fuel and coolant, the lack of an approved licensing framework, the lack of qualified, salt-compatible structural materials, and the potential for tritium release into the environment are the most obvious issues that remain to be resolved.

Holcomb, David Eugene↗

A gas-loading system for LANL two-stage gas guns

A novel gas loading system was designed for the specific application of remotely loading high purity gases into targets for gas-gun driven plate impact experiments. The high purity gases are loaded into well-defined target configurations to obtain Hugoniot states in the gas phase at greater than ambient pressures.The small volume of the gas samples is challenging, as slight changing in the ambient temperature result in measurable pressure changes. Therefore, the ability to load a gas gun target and continually monitor the sample pressure prior to firing provides the most stable and reliable target fielding approach. We present the design and evaluation of a gas loading system built for the LANL 50 mm bore two-stage light gas gun. Targets for the gun are made of 6061 Al or OFHC Cu, and assembled to form a gas containment cell with a volume of approximately 1.38 cc. The compatibility of materials was a major consideration in the design of the system, particularly for its use with corrosive gases. Piping and valves are stainless steel with wetted seals made from Kalrez® and Teflon®. Preliminary testing was completed to ensure proper flow rate and that the proper safety controls were in place. The system has been used to successfully load Ar, Kr, Xe, and anhydrous ammonia with purities of up to 99.999 percent. The design of the system and example data from the plate impact experiments will be shown.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Low Cost Hydrogen Storage at 875 Bar Using Steel Liners and Steel Wire Wraps

The Department of Energy’s (DOE) Fuel Cell Technologies Office (FCTO) within the Office of Energy Efficiency and Renewable Energy (EERE) supports research and development activities leading to the development of low-cost, high-pressure hydrogen storage systems for use in hydrogen refueling stations (forecourt). The specific goals of this project were to develop and produce a prototype of a pressure vessel to safely store gaseous hydrogen at 875 bar that meets the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Section VIII, Division 3 design code for service in hydrogen (Article KD-10) and meets the DOE storage tank cost target of <$1000/kg stored hydrogen (H 2 ). The pressure vessel designed and prototyped as part of this study utilizes a standard ASME approved, 406 mm diameter, 31.7 mm thick wall, and 9.14m long, liner with a capacity of 765 liters and rated for a pressure of up to 460 bar. The liner was wrapped with high strength steel wires to boost its pressure rating to 875 bars. The process of wrapping metal liners with a high strength steel wire, a WireTough patented technology, was first demonstrated on short cylinders that were 1.9 m long but of the same diameter and wall thickness as the 9.1 m long, 765 L cylinders. Subsequently, full length cylinders that were 9.14 m long were designed and certified under the applicable ASME Design Codes. Two prototype cylinders were wire wrapped to demonstrate the manufacturability. Following is a bulleted summary of the accomplishments of the project that ended on August 31, 2018.

25 ENERGY STORAGE↗

Dual-Purpose Canister Filling Demonstration Project Progress Report at ORNL, 2023

The US DOE Office of Nuclear Energy is investigating the feasibility of direct disposal of dual-purpose canisters (DPCs) in a hypothetical geological repository to offset the potential requirement to repackage spent nuclear fuel (SNF) from existing DPCs into smaller, disposal-ready canisters. Oak Ridge National Laboratory (ORNL) is currently evaluating the feasibility of filling void space in loaded DPCs with an engineered material to prevent a criticality event caused by groundwater/moderator intrusion. Metal alloys are being investigated as a filler material because of their relatively low viscosities when molten, which may facilitate their injection via an existing drainpipe that runs almost the full length of the DPC. ORNL’s strategy for evaluating filler viability includes simulations and physical demonstrations of filling and casting behavior, as well as evaluations of materials for compatibility in the repository environment. Filling of DPCs in this manner is expected to mitigate the risk associated with a post-closure criticality event during the repository performance assessment time frame (10,000 years or greater). Efforts in this fiscal year focused on (1) destructive analysis of experimental filler castings made in FY 2022, (2) a report outlining a conceptual design of a DPC filling facility (Fortner et al., 2023, M3SF 23OR010305044/ ORNL/SPR-2023/2921, May 31, 2023), (3) a report on affected features, events, and processes (FEPs) due to DPC filling (Price et al., 2023, M3SF-23SN010305093, issuance pending), (4) developing and testing a more practical alloy filler based upon a Sn-Al eutectic, and (5) modeling the heating and cooling dynamics of a DPC subjected to molten metal filling. The preliminary results from each of these tasks support the feasibility of filling DPCs with metal as a strategy against the possibility of criticality in the repository. The FY 2022 casting was found to penetrate even very small orifices in the mold and internal structures. Preliminary testing of the Sn-Al eutectic indicate little interaction of the melt with Zircaloy cladding. Thermal modelling shows that a filled DPC will cool to manageable temperatures within 2-3 days, which is likely manageable in a facility.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Microfabricated Ion Traps on Sapphire for Larger Trap Areas and Higher Qubit Count

Surface ion traps are a promising platform for quantum computing due to their potential to store large numbers of ions that can be addressed by electrical and optical control signals in order to implement quantum algorithms. Increasing the power of the quantum computer requires increasing the number of ions, but this poses a significant challenge in that it leads to a non-linear increase in on-chip power dissipation. The primary contributor to this power scaling in current devices is the capacitance between the radio frequency (RF) electrode and the metal plane that shields the silicon substrate from the RF signals applied to it. Silicon has traditionally been chosen for the substrate material for compatibility with the processing required for multi-metal-level traps. In this work, we address these capacitance and fabrication challenges by replacing the commonly used silicon substrate with an insulating sapphire substrate to fabricate a multi-metal-level ion trap, while still employing common semiconductor manufacturing techniques. This change in substrate allows the design to remove the metal shielding from the device design, reducing the capacitance of the RF electrode. The electrical characteristics of these traps were measured, specifically trap impedance, capacitance, and voltage breakdown, and compared to nearly identical silicon trap devices. Finally, we used laser cutting techniques to shape a sapphire wafer into bowtie shapes matching silicon traps previously fabricated at Sandia National Labs to explore solutions for integrating sapphire substrates into non-rectangular ion trap designs.

97 MATHEMATICS AND COMPUTING↗

Compatibility Studies of Various Refractory Materials in Contact with Molten Silicon

The production of low cost, efficient solar cells for terrestrial electric power generation involves the manipulation of molten silicon with a present need for noncontaminating, high temperature refractories to be used as containment vessels, ribbon-production dies, and dip-coated substrates. Studies were conducted on the wetting behavior and chemical/physical interactions between molten silicon and various refractory materials.

Odonnell, T.↗

Design, fabrication, test, and evaluation of a prototype 150-foot long composite wind turbine blade

The design, fabrication, testing, and evaluation of a prototype 150 foot long composite wind turbine blade is described. The design approach and material selection, compatible with low cost fabrication methods and objectives, are highlighted. The operating characteristics of the blade during rotating and nonrotating conditions are presented. The tensile, compression, and shear properties of the blade are reported. The blade fabrication, tooling, and quality assurance are discussed.

Gewehr, H. W.↗

Development of a lithium secondary battery separator

A nonporous membrane based on the polymerization of 2,3-dihydrofuran followed by crosslinking in situ was prepared. The material is compatible with rechargeable Li battery components and, when swollen with an appropriate solvent such as tetrahydrofuran, exhibits separator resistance and Li transport equivalent to Celgard.

Moore, J. A.↗

Low power arcjet life issues

The present evaluation of the results of arcjet engine lifetime testing attempts to deepen understanding of the electrode erosion process, with a view to its minimization. Attention is given to the compatibility of materials with N2H4, the dependence of electrode erosion on geometry and flow field, and the erosive effects associated with the arcjet power supply. Results are presented for thrusters employing either decomposed N2H4 or cold mixed gases, over a power range of 900 to 2000 W.

Simon, M. A.↗

Gland With Cantilever Seal

Single-piece gland forms tight seal on probe or tube containing liquid or gas at high pressure. Gland and probe align as assembled by simple torquing procedure. Disconnected easily and reused at same site. Made from any of wide variety of materials so compatible with application. Cantilever ring at top of gland bites into wall of tube or probe, sealing it. Wall of tube or probe must be thick enough to accommodate deformation without rupturing. Maximum deformation designed in coordination with seating and deformation of boss or conical seal.

Melton, Patrick B.↗

Oxygen Systems Cleaners for Aerospace Applications

New environmental regulations have forced extensive evaluations of many different cleaning agents for use in oxygen systems. This is no simple process because pure oxygen is a very strong oxidizer, and when placed in contact with a foreign substance, the combination may be explosive. This foreign substance can easily be a cleaning agent residue left over in the oxygen system after cleaning. This paper focuses on the factors that must be considered when selecting a cleaning agent for oxygen systems, as well as the approval processes which are currently being utilized by NASA for oxygen compatibility of materials. This paper will provide a working description of how to begin selecting a cleaning agent for oxygen systems. The paper will present the following: Background information on the necessity of a stringent selection process for oxygen system cleaners; Specifications and regulations concerning cleaning for oxygen service; Changing oxygen cleaning specifications given current environmental concerns; Testing for cleanliness in oxygen systems, Cleaning agents that have been tested for oxygen systems, including an extensive list of some of the newer 'environmentally friendly' cleaning agents; and Test results and conclusions from the testing. The paper will also provide instructions on the proper procedures for obtaining NASA approval on a candidate oxygen systems cleaning agent.

Davis, Samuel E.↗

Optimal Design of Aortic Leaflet Prosthesis

The design criteria for an optimum prosthetic-aortic leaflet valve are a smooth washout in the valve cusps, minimal leaflet stress, minimal transmembrane pressure for the valve to open, an adequate lifetime (for a given blood-compatible leaflet material's fatigue data). A rigorous design analysis is presented to obtain the prosthetic tri-leaflet aortic valve leaflet's optimum design parameters. Four alternative optimum leaflet geometries are obtained to satisfy the criteria of a smooth washout and minimal leaflet stress. The leaflet thicknesses of these four optimum designs are determined by satisfying the two remaining design criteria for minimal transmembrane opening pressure and adequate fatigue lifetime, which are formulated in terms of the elastic and fatigue properties of the selected leaflet material - Avcothane-51 (of the Avco-Everett Co. of Massachusetts). Prosthetic valves are fabricated on the basis of the optimum analysis and the resulting detailed engineering drawings of the designs are also presented in the paper.

Ghista, Dhanjoo N.↗

Compositional Evolution of Saturn's Ring: Ice, Tholin, and 'CHIRON'-Dust

We address compositional evolution in planetary ring systems subsequent to meteoroid bombardment. The huge surface area to mass ratio of planetary rings ensures the importance of this process, given currently expected values of meteoroid flux. We developed a model which includes both direct deposition of extrinsic meteoritic 'pollutants', and ballistic transport of the increasingly polluted ring material as impact ejecta. Certain aspects of the observed regional variations in ring color and albedo can be understood in terms of such a process. We conclude that the regional scale color and albedo differences between the C ring and B ring can be understood if all ring material began with the same composition (primarily water ice, based on other data, but colored by tiny amounts of non-icy, reddish absorber) and then evolved entirely by addition and mixing of extrinsic, neutrally colored, highly absorbing material. This conclusion is readily extended to the Cassini Division and its surroundings as well. Typical silicates are unable to satisfy the ring color, spectroscopic, and microwave absorption constraints either as intrinsic or extrinsic non-icy constituents. However, 'Titan Tholin' provides a satisfactory match for the inferred refractive indices of the 'pre-pollution' nonicy ring material. The extrinsic bombarding material is compatible with the properties of Halley or Chiron, but not with the properties of other 'red' primitive objects such as Pholus. We further demonstrate that the detailed radial profile of color across the abrupt B ring - C ring boundary is quite compatible with such a 'pollution transport' process, and that the shape of the profile can constrain key parameters in the model. We use the model to estimate the 'exposure age' of Saturn's rings to extrinsic meteoroid flux. We obtain a geologically young 'age' which is compatible with timescales estimated independently based on the evolution of ring structure due to ballistic transport, and also with other 'short timescales' estimated on the grounds of gravitational torques.

Cuzzi, Jeffrey N.↗

Results From Cs Activated GaN Photocathode Development for MCP Detector Systems at GSFC

We describe the development of high quantum efficiency W photocathodes for use in large area two dimensional microchannel plate based detector arrays to enable new W space astronomy missions. Future W missions will require improvements in detector sensitivity, which has the most leverage for cost-effective improvements in overall telescope/instrument sensitivity. We use new materials such as p-doped GaN, AIGaN, ZnMgO, Sic and diamond. We have currently obtained QE values > 40 % at 185 nm with Cesiated GaN, and hope to demonstrate higher values in the future. By using controlled internal fields and nano-structuring of the surfaces, we plan to provide field emission assistance for photoelectrons while maintaining their energy distinction from dark noise electrons. We will transfer these methods from GaN to ZnMgO, a new family of wide band-gap materials more compatible with microchannel plates. We also are exploring technical parameters such as doping profiles, internal and external field strengths, angle of incidence, field emission assistance, surface preparation, etc.

Norton, Tim↗

History of Sulphur Content Effects on the Thermal Stability of RP-1 under Heated Conditions

As technologies advance in the aerospace industry, a strong desire has emerged to design more efficient, longer life, reusable liquid hydrocarbon fueled rocket engines. To achieve this goal, a more complete understanding of the thermal stability and chemical makeup of the hydrocarbon propellant is needed. Since the main fuel used in modern liquid hydrocarbon systems is RP-1, there is concern that Standard Grade RP-1 may not be a suitable propellant for future-generation rocket engines due to concern over the outdated Mil-Specification for the fuel. This current specification allows high valued limits on contaminants such as sulfur compounds, and also lacks specification of required thermal stability qualifications for the fuel. Previous studies have highlighted the detrimental effect of high levels of mercaptan sulfur content (^50 ppm) on copper rocket engine materials, but the fuel itself has not been studied. While the role of sulfur in other fuels (e.g., aviation, diesel, and automotive fuels) has been extensively studied, little has been reported on the effects of sulfur levels in rocket fuels. Lower RP-1 sulfur concentrations need to be evaluated and an acceptable sulfur limit established before RP-1 can be recommended for use as the propellant for future launch vehicles. (5 tables, 8 figures, 9 refs.)

ASTM METHOD D-5623↗