Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LOW SPEED STABILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Aerodynamic Analysis of the Elytron 2S Experimental Tiltwing Aircraft

The Elytron 2S is a prototype aircraft concept to allow VTOL capabilities together with fixed wing aircraft performance. It has a box wing design with a centrally mounted tilt-wing supporting two rotors. This paper explores the aerodynamic characteristics of the aircraft using computational fluid dynamics in hover and low speed forward flight, as well as analyzing the unique control system in place for hover. The results are then used to build an input set for NASA Design and Analysis if Rotorcraft software allowing trim and flight stability and control estimations to be made with SIMPLIFLYD.

Elytron 2S↗
NASA NTRS2021

The 32-year Record-high Surface Melt in 2019/2020 on the Northern George VI Ice Shelf, Antarctic Peninsula

In the 2019/2020 austral summer, the surface melt duration and extent on the northern George VI Ice Shelf (GVIIS) was exceptional compared to the 31 previous summers of distinctly lower melt. This finding is based on analysis of near-continuous 41-year satellite microwave radiometer and scatterometer data, which are sensitive to meltwater on the ice shelf surface and in the near-surface snow. Using optical satellite imagery from Landsat 8 (2013 to 2020) and Sentinel-2 (2017 to 2020), record volumes of surface meltwater ponding were also observed on the northern GVIIS in 2019/2020, with 23 % of the surface area covered by 0.62 km3 of ponded meltwater on 19 January. These exceptional melt and surface ponding conditions in 2019/2020 were driven by sustained air temperatures ≥0 ∘C for anomalously long periods (55 to 90 h) from late November onwards, which limited meltwater refreezing. The sustained warm periods were likely driven by warm, low-speed (≤7.5 m s−1) northwesterly and northeasterly winds and not by foehn wind conditions, which were only present for 9 h total in the 2019/2020 melt season. Increased surface ponding on ice shelves may threaten their stability through increased potential for hydrofracture initiation; a risk that may increase due to firn air content depletion in response to near-surface melting.

Alison F. Banwell↗
NASA NTRS2020

Convolutional Neural Network for Transition Modeling Based on Linear Stability Theory

Transition prediction is an important aspect of aerodynamic design because of its impact on skin friction and potential coupling with flow separation characteristics. Traditionally, the modeling of transition has relied on correlation-based empirical formulas based on integral quantities such as the shape factor of the boundary layer. However, in many applications of computational fluid dynamics, the shape factor is not straightforwardly available or not well-defined. We propose using the complete velocity profile along with other quantities (e.g., frequency, Reynolds number) to predict the perturbation amplification factor. While this can be achieved with regression models based on a classical fully connected neural network, such a model can be computationally more demanding. We propose a novel convolutional neural network inspired by the underlying physics as described by the stability equations. Specifically, convolutional layers are first used to extract integral quantities from the velocity profiles, and then fully connected layers are used to map the extracted integral quantities, along with frequency and Reynolds number, to the output (amplification ratio). Numerical tests on classical boundary layers clearly demonstrate the merits of the proposed method. More importantly, we demonstrate that, for Tollmien-Schlichting instabilities in two-dimensional, low-speed boundary layers, the proposed network encodes information in the boundary layer profiles into an integral quantity that is strongly correlated to a well-known, physically defined parameter – the shape factor.

Laminar-turbulent transition↗
NASA NTRS1968

Solid state high-voltage pulser operates with low supply voltage

High speed klystron cathode pulser requires low voltage to generate high-voltage pulses. Broadband video transformers are wound in two configurations - /1/ transmission line, multifilar toroids and /2/ loop coupling toroids. The circuit adapts to generate high-speed, high-voltage, high-stability power pulses at megawatt levels.

Milberger, W. E.↗
NASA NTRS2003

Characterization of Al-Cu-Mg-Ag Alloy RX226-T8 Plate

Aluminum-copper-magnesium-silver (Al-Cu-Mg-Ag) alloys that were developed for thermal stability also offer attractive ambient temperature strength-toughness combinations, and therefore, can be considered for a broad range of airframe structural applications. The current study evaluated Al-Cu-Mg-Ag alloy RX226-T8 in plate gages and compared performance with sheet gage alloys of similar composition. Uniaxial tensile properties, plane strain initiation fracture toughness, and plane stress tearing resistance of RX226-T8 were examined at ambient temperature as a function of orientation and thickness location in the plate. Properties were measured near the surface and at the mid-plane of the plate. Tensile strengths were essentially isotropic, with variations in yield and ultimate tensile strengths of less than 2% as a function of orientation and through-thickness location. However, ductility varied by more than 15% with orientation. Fracture toughness was generally higher at the mid-plane and greater for the L-T orientation, although the differences were small near the surface of the plate. Metallurgical analysis indicated that the microstructure was primarily recrystallized with weak texture and was uniform through the plate with the exception of a fine-grained layer near the surface of the plate. Scanning electron microscope analysis revealed Al-Cu-Mg second phase particles which varied in composition and were primarily located on grain boundaries parallel to the rolling direction. Fractography of toughness specimens for both plate locations and orientations revealed that fracture occurred predominantly by transgranular microvoid coalescence. Introduction High-strength, low-density Al-Cu-Mg-Ag alloys were initially developed to replace conventional 2000 (Al-Cu-Mg) and 7000 (Al-Zn-Cu-Mg) series aluminum alloys for aircraft structural applications [1]. During the High Speed Civil Transport (HSCT) program, improvements in thermal stability were demonstrated for candidate aircraft wing and fuselage skin materials through the addition of silver to Al-Cu-Mg alloys based on Al 2519 chemistry [2]. Thermal stability of the resulting Al-Cu-Mg-Ag alloys, C415-T8 and C416-T8, was due to co-precipitation of the thermally stable . (AlCu) and ' (Al2Cu) strengthening phases [1-4]. The strength and toughness behavior was investigated for these alloys produced as 0.090-inch thick rolled sheet in the T8 condition and after various thermal exposures. The mechanical properties were shown to be competitive with conventional aircraft alloys, 2519-T8 and 2618-T8 [2]. During the Integral Airframe Structure (IAS) program, advanced aluminum alloys were examined for use in an integrally stiffened airframe structure where the skin and stiffeners would be machined from plate and extruded frames would be mechanically attached (see Figure 1) [5]. Advantages of integrally stiffened structure include reduced part count, and reduced assembly times compared to conventional built-up airframe structure. The near-surface properties of a thick plate are of significance for a machined integrally stiffened airframe structure since this represents the skin location. Properties measured at the mid-plane of the plate are more representative of the stiffener web. RX226 was developed to exploit strength-toughness improvements and thermal stability benefits of Al-Cu-Mg-Ag alloys in plate gages. This study evaluated the microstructure and properties of three gages of plate produced in the T8 condition.

Lach, Cynthia L.↗
NASA NTRS1977

Low speed wind tunnel tests of 1/10-scale model of a blended-arrow supersonic cruise aircraft

Low speed static force tests have been conducted in a full scale tunnel to determine the low speed aerodynamic characteristics of a 1/10-scale model of a blended-arrow supersonic cruise aircraft. A clean configuration and a high lift configuration with several combinations of leading- and trailing-edge flaps to provide improved lift and longitudinal stability in the landing and takeoff modes were used. The tests were made at angles of attack from about -6 deg to 30 deg, sideslip angles from -5 deg to 10 deg, and Reynolds numbers from 6.78 x 1 million to 13.85 x 1 million corresponding to test velocities of 41 to 85 knots.

Mclemore, H. C.↗
NASA NTRS1962

Aerodynamic Analysis of Tektites and Their Parent Bodies

Experiment and analysis indicate that the button-type australites were derived from glassy spheres which entered or re-entered the atmosphere as cold solid bodies; in case of average-size specimens, the entry direction was nearly horizontal and the entry speed between 6.5 and 11.2 km/sec. Terrestrial origin of such spheres is impossible because of extremely high deceleration rates at low altitudes. The limited extension of the strewn fields rules out extraterrestrial origin of clusters of such spheres because of stability considerations for clusters in space. However, tektites may have been released as liquid droplets from glassy parent bodies ablating in the atmosphere of the earth. The australites then have skipped together with the parent body in order to re-enter as cold spheres. Terrestrial origin of a parent body would require an extremely violent natural event. Ablation analysis shows that fusion of opaque siliceous stone into glass by aerodynamic heating is impossible.

Adams, E. W.↗
NASA NTRS2004

Energy Management of Manned Boost-Glide Vehicles: A Historical Perspective

As flight progressed from propellers to jets to rockets, the propulsive energy grew exponentially. With the development of rocket-only boosted vehicles, energy management of these boost-gliders became a distinct requirement for the unpowered return to base, alternate landing site, or water-parachute landing, starting with the X-series rocket aircraft and terminating with the present-day Shuttle. The problem presented here consists of: speed (kinetic energy) - altitude (potential energy) - steep glide angles created by low lift-to-drag ratios (L/D) - distance to landing site - and the bothersome effects of the atmospheric characteristics varying with altitude. The primary discussion regards post-boost, stabilized glides; however, the effects of centrifugal and geopotential acceleration are discussed as well. The aircraft and spacecraft discussed here are the X-1, X-2, X-15, and the Shuttle; and to a lesser, comparative extent, Mercury, Gemini, Apollo, and lifting bodies. The footprints, landfalls, and methods developed for energy management are also described. The essential tools required for energy management - simulator planning, instrumentation, radar, telemetry, extended land or water range, Mission Control Center (with specialist controllers), and emergency alternate landing sites - were first established through development of early concepts and were then validated by research flight tests.

Day, Richard E.↗
NASA NTRS1958

A Flight Evaluation of the Factors which Influence the Selection of Landing Approach Speeds

The factors which influence the selection of landing approach speeds are discussed from the pilot's point of view. Concepts were developed and data were obtained during a landing approach flight investigation of a large number of jet airplane configurations which included straight-wing, swept-wing, and delta-wing airplanes as well as several applications of boundary-layer control. Since the fundamental limitation to further reductions in approach speed on most configurations appeared to be associated with the reduction in the pilot's ability to control flight path angle and airspeed, this problem forms the basis of the report. A simplified equation is presented showing the basic parameters which govern the flight path angle and airspeed changes, and pilot control techniques are discussed in relation to this equation. Attention is given to several independent aerodynamic characteristics which do not affect the flight path angle or airspeed directly but which determine to a large extent the effort and attention required of the pilot in controlling these factors during the approach. These include stall characteristics, stability about all axes, and changes in trim due to thrust adjustments. The report considers the relationship between piloting technique and all of the factors previously mentioned. A piloting technique which was found to be highly desirable for control of high-performance airplanes is described and the pilot's attitudes toward low-speed flight which bear heavily on the selection of landing approach speeds under operational conditions are discussed.

Drinkwater, Fred J., III↗
NASA NTRS1987

Preliminary results of a flight investigation of rotorcraft control and display laws for hover

A flight experiment designed to evaluate the effects of compatible versus incompatible display and control system response characteristics, and to evaluate a candidate display law design methodology, is described. The experiment was conducted on the NASA/Army CH-47B variable-stability helicopter using its model-following control system and a color, panel-mounted display. Three control response types representative of modern highly augmented rotorcraft and three corresponding sets of display dynamics were considered for three hover and low-speed tasks performed in simulated instrument conditions. Preliminary results based on pilot handling qualities ratings and comments indicate that performance and workload can be significantly affected by certain control and display combinations and that the display design methodology shows promise for improving the handling qualities of rotorcraft operating in conditions of low visibility.

Eshow, Michelle M.↗
NASA NTRS1993

A comparison of airborne eddy correlation and bulk aerodynamic methods for ocean-air turbulent fluxes during cold-air outbreaks

The viscous interfacial-sublayer model of Liu et al. (1979) is used to derive four bulk schemes (LKB, FG, D, and DB), with the flux-profile relationships of Lie et al., Francey and Garratt (1981), Dyer (1974), and Dyer and Bradley (1982). These schemes, with stability-dependent transfer coefficients, are tested against the eddy-correlation fluxes measured at the 50-m flight level above the western Atlantic Ocean during cold-air outbreaks. The bulk fluxes of momentum (tau), sensible heat (H), and latent heat (E) are found to increase with various von Karman constants. The dependence of transfer coefficients on wind speeds and roughness lengths is discussed. The transfer coefficients for tau and E agree excellently between LKB and FG. The ratio of the coefficent for H of LKB to that of FG, increasing with decreasing stability, is very sensitive to stability at low winds, but approaches the neutral value of 1.25 at high winds.

Chou, Shu-Hsien↗
NASA NTRS2019

Computational Study of a Generic T-tail Transport

This paper presents a computational study on the static and dynamic stability characteristics of a generic transport T-tail configuration under a NASA research program to improve stall models for civil transports. The NASA Tetrahedral Unstructured Software System (TetrUSS) was used to obtain both static and periodic dynamic solutions at low speed conditions for three Reynolds number conditions up to 60 deg angle of attack. The computational results are compared to experimental data. The dominant effects of Reynolds number for the static conditions were found to occur in the stall region. The pitch and roll damping coefficients compared well to experimental results up to up to 40 deg angle of attack whereas yaw damping coefficient agreed only up to 20 deg angle of attack.

McMillin, S. Naomi↗
NASA NTRS1987

Wind tunnel results of the low-speed NLF(1)-0414F airfoil

The large performance gains predicted for the Natural Laminar Flow (NLF)(1)-0414F airfoil were demonstrated in two-dimensional airfoil tests and in wind tunnel tests conducted with a full scale modified Cessna 210. The performance gains result from maintaining extensive areas of natural laminar flow, and were verified by flight tests conducted with the modified Cessna. The lift, stability, and control characteristics of the Cessna were found to be essentially unchanged when boundary layer transition was fixed near the wing leading edge. These characteristics are very desirable from a safety and certification view where premature boundary layer transition (due to insect contamination, etc.) must be considered. The leading edge modifications were found to enhance the roll damping of the Cessna at the stall, and were therefore considered effective in improving the stall/departure resistance. Also, the modifications were found to be responsible for only minor performance penalties.

Murri, Daniel G.↗
NASA NTRS1991

The role of time and speed in NASA's SUNLITE program

The SUNLITE program of NASA's LaRC aims to demonstrate lower noise and better frequency stability for continuous-wave (CW) solid-state lasers in the microgravity environment of space. The program will utilize laser-diode-pumped nonplanar-ring oscillators regulated by ultra-stable high-finesse Fabry-Perot Spectrometers to produce light beams with phase rate or frequency variations as low as 3 Hz. SUNLITE will use the period-method (P-method) to measure the phase rate and frequency stability of the lasers. The P-method was chosen because it requires less memory space for the raw data, because frequencies can be analyzed on-line in real-time simply by reciprocating the periods (fi = 1/pi), and because the mean and variance of the frequencies can be calculated as fast or faster than they can be with the fastest fast Fourier transformations. Furthermore, for a given signal-to-noise power ratio, the P-method requires less data and less computer time to extract the noise components. Although the P-method does require fast Time Interval Counters, the Fourier transformation method requires comparably fast Sampling Volt meters. For either method, however, time and computer speed play a critical role.

Hafele, Joseph C.↗
NASA NTRS1951

Flight-Determination of the Low-Lift Drag and Longitudinal Stability of a 1/10-Scale Rocket-Powered Model of the Douglas XF4D-1 Airplane at Mach Numbers from 0.7

A flight investigation has been made to determine the drag and longitudinal stability of a 1/10- scale model of the Douglas XF4D-1 airplane from Mach numbers 0.7 to 1.4 at lift coefficients near zero. The drag rise occurred near M = 0.95. The external drag coefficient was a constant value of about 0.012 at subsonic speeds up to the point of drag rise where it increased abruptly to a value of 0.030 at M = 1.0 followed by a more gradual increase to a value of 0.038 at M = 1.25. The model indicated that, at 35,000 feet and a level-flight free-stream Mach number of 1.0, the drag of the full-scale airplane would exceed the thrust available from an XJ40-WE-8 engine with after-burning. The transonic trim change was small. The aerodynamic center moved gradually from the most forward location of 21.0-percent mean aerodynamic chord at M = 0.9 to the most rearward location of 40-percent mean aerodynamic chord at M = 1.25. The damping in pitch was low.

Mitcham, Grady L.↗
DOE OSTI2020

Low- n global ideal MHD instabilities in the CFETR baseline scenario

This article reports an evaluation on the linear ideal magnetohydrodynamic (MHD) stability of the China Fusion Engineering Test Reactor (CFETR) baseline scenario for various first-wall locations. The initial-value code NIMROD and eigen-value code AEGIS are employed in this analysis. Despite the distinctly different approaches in modeling the scrape off layer region, the dominant growth in each of the low-n (n=1–10) modes are consistent between the two codes. We report the higher-n modes are dominated by ballooning modes and localized in the pedestal region, while the lower-n modes have more prominent external kink components and broader mode profiles. The influence of the plasma-vacuum profile and wall shape are also examined using NIMROD. In the presence of a resistive wall, the low-n ideal MHD instabilities are further studied using AEGIS. For the designed first-wall location, the n=1 resistive wall mode is found to be unstable, which could be fully stabilized by uniform toroidal rotation above the 2.9% core Alfven speed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1985

Launching rockets and small satellites from the lunar surface

Scientific payloads and their propulsion systems optimized for launch from the lunar surface differ considerably from their counterparts for use on earth. For spin-stabilized payloads, the preferred shape is a large diameter-to-length ratio to provide stability during the thrust phase. The rocket motor required for a 50-kg payload to reach an altitude of one lunar radius would have a mass of about 41 kg. To place spin-stabilized vehicles into low altitude circular orbits, they are first launched into an elliptical orbit with altitude about 840 km at aposelene. When the spacecraft crosses the desired circular orbit, small retro-rockets are fired to attain the appropriate direction and speed. Values of the launch angle, velocity increments, and other parameters for circular orbits of several altitudes are tabulated. To boost a 50-kg payload into a 100-km altitude circular orbit requires a total rocket motor mass of about 90 kg.

Anderson, K. A.↗
NASA NTRS1991

A bulk flow model of a brush seal system

Fibers can be readily fabricated into a variety of seal configurations that are compliant and responsive to high speed or lightly loaded systems. A linear, circular, or contoured brush seal system is a contact seal consisting of the bristle pattern and hardened interface. When compared to a labyrinth seal, the brush seal system is superior and features low leakage, dynamic stability, and permits compliant structures. But in turn, the system usually requires a hardened smooth interface and permits only limited pressure drops. Wear life and wear debris for operations with static or dynamic excitation are largely undetermined. A seal system involves control of fluid within specific boundaries. The brush and rub ring (or rub surface) form a seal system. Design similitudes, a bulk flow model, and rub ring (interface) coatings are discussed. The bulk flow model calculations are based on flows in porous media and filters. The coatings work is based on experience and expanded to include current practice.

Hendricks, R. C.↗