SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Heat Flow modeled for moving or stationary rod shaped sample inside directional-solidification furnace. Program effectively models one-dimensional heat flow in translating or motionless rod-shaped sample inside of directionalsolidification furnace in which adiabatic zone separates hot zone and cold zone. Applicable to systems for which Biot numbers in hot and cold zones are less than unity.
Unidirectional solidification yields bulk crystals with compositional homogeneity. Unidirectionaly crystal-growth furnace assembly travels vertically so crystal grows upward from bottom tapered end of ampoule. Separately controlled furnaces used for hot (upper) and cold (lower) zones. New process produces ingots with radial compositional homogeneity suitable for fabricating infrared detectors.
Compositions of glasses and alloys analyzed and corrected in real time. Spectral analysis and temperature measurement performed simultaneously on molten material in container, such as open-hearth furnace, crucible or tank of continuous furnace. Speed of analysis makes it possible to quickly measure concentration of volatile elements depleted by prolonged heating.
Furnace heats and melts circumferential ring of material ("Float Zone") on round bar. In float-zone processing, bar pulled through furnace so zone travels along bar.
Gallium and boron doped silicon solar cells, processed by ion implantation followed by either laser or furnace anneal were irradiated by 1 MeV electrons and their postirradiation recovery by thermal annealing was determined. During the postirradiation anneal, gallium doped cells prepared by both processes recovered more rapidly and exhibited none of the severe reverse annealing observed for similarly processed 2 ohm-cm boron doped cells. Ion implanted furnace annealed 0.1 ohm-cm boron doped cells exhibited the lowest post-irradiation annealing temperatures after irradiation. The drastically lowered recovery temperature is attributed to the reduced oxygen and carbon content of the 0.1 ohm-cm cells. Analysis based on defect properties and annealing kinetics indicates that further reduction in annealing temperature is attainable with further reduction in the silicon's carbon and/or divacancy content after irradiation.
An ADSS-P directional solidification furnace was reconfigured for operation on the KC-135 low-g aircraft. The system offers many advantages over quench ingot methods for study of the effects of sedimentation and convection on alloy formation. The directional sodification furnace system was first flown during the September 1982 series of flights. The microstructure of the hypereutectic cast iron sample solidified on one of these flights suggests a low-g effect on graphite morphology. Further experiments are needed to ascertain that this effect is due to low-gravity and to deduce which of the possible mechanisms is responsible for it.
Thermally generated stresses in the growing web crystal were reduced. These stresses, which if too high cause the ribbon to degenerate, were reduced by a factor of three, resulting in the demonstrated growth of high-quality web crystals to widths of 5.4 cm. This progress was brought about chiefly by the application of thermal models to the development of low-stress growth configurations. A new temperature model was developed which can analyze the thermal effects of much more complex lid and top shield configurations than was possible with the old lumped shield model. Growth experiments which supplied input data such as actual shield temperature and melt levels were used to verify the modeling results. Desirable modifications in the melt level-sensing circuitry were made in the new experimental web growth furnace, and this furnace has been used to carry out growth experiments under steady-state conditions. New growth configurations were tested in long growth runs at Westinghouse AESD which produced wider, lower stress and higher quality web crystals than designs previously used.
Experimental results are summarized, and it is pointed out that gravity-driven convection can alter the diffusive-advective mass transport behavior in the growth of crystals by physical vapor transport. Specially designed and constructed transparent furnaces are described which are being used to study the effects of gravity in the crystal growth of the compound semiconductors PbTe and CdTe. The theory underlying vapor transport behavior is reviewed, with attention given to the vapor-solid behavior of compound materials, to one-dimensional mass transport, and to gravity-induced (natural) convection. In the transparent furnaces, the quartz capillary tube mounted along the axis of the main quartz ampoule is used to measure the temperature at the growth surface (vapor-solid crystal interface) and the source, as well as the complete temperature profile along the axis of the tube. The light-pipe works to remove heat from the growth end of the ampoule by radiative heat transfer. The ampoules are sealed after being evacuated to the low 10 to the -8th torr range with a cryogenic vacuum pump.
Insulating blanket resists temperatures up to 1,500 degrees F (815 degrees C). Useful where high-temperature resistance, flexibility, and ease of installation are important - for example, insulation for odd-shaped furnaces and high-temperature ducts, curtains for furnace openings and fire control, and conveyor belts in hot processes. Blanket is quilted composite consisting of two face sheets: outer one of silica, inner one of silica or other glass cloth with center filling of pure silica glass felt sewn together with silica glass threads.
The Hg/Cd/Te solidification in a Bridgman cell was thermally analyzed by Continuum's VAST code. The energy equation is solved in an axisymmetric, quasi steady domain for both the molten and solid alloy regions. Alloys composition is calculated by a simplified one dimensional model to estimate its effect on melt thermal conductivity and, consequently, on the temperature field within the cell. Solidification is assumed to occur at a fixed temperature of 979 K. Simplified boundary conditions are included to model both the radiant and conductive heat exchange between the furnace walls and the alloy. Calculations are performed to show how the steady state isotherms are affected by: (1) the hot and cold furnace temperatures; (2) boundary condition parameters; and (3) the growth rate which affects the calculated alloy's composition.
Single, (001)-oriented crystals of PWA 1480 were processed in alumina/silica shell molds in a laboratory high gradient furnace. The furnace employs a graphite resistance heated element, a radiation baffle, and a water cooled radiation trap below the baffle. All crystals were grown in vacuum (10 torr) and all heat transfer was radiative. The element is constructed with a variable cross section that is tapered just above the baffle to maximize heat input and therefore thermal gradient. A maximum alloy temperature of 1600 C was used. A thermal gradient of 130 deg C/cm was recorded at 1370 C just above the solidus of the PWA 1480 alloys. Crystal bars with 14.4 and 17.5 mm diameters were grown in alumina/silica shell molds. Each crystal was started from a 1.6 mm pencil seed at a rate of 76 mm/hr and slowly accelerated to a rate of 200 mm/hr under computer control. Volume percent porosity and average pore size were measured as functions of distance in representative bars. Low cycle fatigue behavior and stress rupture properties were determined.
The purpose of this effort was to consider and evaluate some specific concepts for performing a number of extremely low gravity (i.e., microgravity) experiments involving the directional solidification of samples of high carbon, cast iron alloys. The specific experiments considered herein were conceived to permit scientific investigation of the resultant microstructures and mechanical properties of the test samples after the microgravity environment processing. This study was limited to consideration of the NASA/MSFC furnace payloads, referred to herein as the Automated Directional Solidification Furnace (ADSF) systems. Three ADSF systems were reviewed and are as follows: (1) Low temperature ADSF (ADSF-1); (2) High temperature ADSF (ADSF-2); and (3) Advanced ADSF (AADSF).
Approximate thermal conductivities determined rapidly. Two specimens, to be compared, placed in assembly with insulation. One end of assembly placed in furnace. Temperature of furnace, of each end, and of center of each specimen recorded. Procedure used to rate quickly candidate materials for applications in which thermal conductivity prime consideration.
This research is composed of three major components: (1) development of interface morphology control for automated Bridgman growth of semiconductor systems; (2) comparative analysis of segregation during crystal growth in a reduced gravity environment and in the presence of magnetic fields; and (3) consequences of seeding by meltback in Bridgman growth under reduced gravity conditions. In attempts to optimize furnace design for crystal growth in a reduced gravity environment, an analytical approach to heat transfer was developed. It was thus found that charge confining crucibles diminish the ability to control the growth interface morphology through its position within the gradient zone. A heat pipe hot zone system for Bridgman growth, in reduced gravity environment, of crystal with diameters up to 16 mm was developed. For growth of Ga-doped germanium in the multipurpose (ASTP) furnace, it was found that the application of transverse magnetic fields (up to 36 kg) does not substantially increase the effective distribution coefficient; i.e., diffusion-controlled segregation observed in reduced gravity environment cannot be reached nor approached by magnetic field induced melt stabilization.
Sodium sulfate induced corrosion of a molybdenum containing nickel-base superalloy, Udimet 700, was studied in laboratory furnace tests and in a high velocity (Mach 0.3) burner rig. The effect of SO2 content in the atmosphere on the corrosion behavior in the laboratory furnace tests was determined. Catastrophic corrosion occurs only when the melt contains MoO3 in addition to Na2SO4 and Na2MoO4. The conditions under which catastrophic corrosion occurs are identified and a mechanism is described to explain the catastrophic corrosion.
Apparatus and method for pulling optical glass fibers in a containerless environment is disclosed which includes a single axis acoustical levitation furnace in which a specimen is levitated and melted. A reflector unit is carried in the interior of the furnace and includes a reflector disposed centrally about the acoustical axis of the levitator. The reflector unit includes a circular shroud of insulation and a copper sleeve inserted in the unit which is hollow at for receiving a cooling medium. A fiber pulling bore is formed centrally in the reflector unit surrounded by cooling jacket to enhance solidification and formation of a fiber. A starting fiber strand is introduced into the melt and pulled outwardly through bore whereby the specimen fiber is started and formed as pulled therethrough. In order to replenish the melt and thus enable a continous process, a movable secondary reflector is provided which captures a supplemental specimen pellet and by movement of the reflector transfers it to the melt.
A process of metallurgical grade (MG) silicon production is presented which appears particularly suitable for photovoltaic (PV) applications. The MG silicon is prepared in a 240 KVA, three electrode submerged arc furnace, starting from high grade quartz and high purity silicon carbide. The silicon smelted from the arc furnace was shown to be sufficiently pure to be directionally solidified to 10 to 15 kg. After grinding and acid leaching, had a material yield larger than 90%. With a MG silicon feedstock containing 3 ppmw B, 290 ppmw Fe, 190 ppmw Ti, and 170 ppmw Al, blended with 50% of off grade electronic grade (EG) silicon to reconduct the boron content to a concentration acceptable for solar cell fabrication, the 99% of deep level impurities were concentrated in the last 5% of the ingot. Quite remarkably this material has OCV values higher tham 540 mV and no appreciable shorts due to SiC particles.
The electrical conductivity of samples of the Murchison and Allende carbonaceous chondrites is 4 to 6 magnitudes greater than rock forming minerals such as Olivine up to 700 C. The remarkably high electrical conductivity of these meteorites is attributed to carbon at grain boundaries. The environment in the wake of the space station can be exploited to produce conditions which will allow pyrolysis of carbonaceous chondrites. An experimental package consisting of a one square meter shield attached to a 15 cm diameter by 40 cm long furnace and tied to a conductance bridge, furnace controller, and digital voltmeter inside the space station via umbilical cable could make the required measurements. Since heating rates as low as 0.1 C/hour are required to study kinetics of the pyrolysis reations which are the cause of the high conductivity of the carbonaceous chondrites, experimental times up to 3 months will be needed.