Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FORMIC ACID”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Glass Frit Clumping and Dusting

DWPF mixes a slurry of glass frit (Frit 418) and dilute (1.5 wt%) formic acid solution with high level waste in the Slurry Mix Evaporator (SME). There would be advantages to introducing the frit in a non-slurry form to minimize water addition to the SME, however, adding completely dry frit has the potential to generate dust which could clog filters or condensers. Prior testing with another type of frit, Frit 320, and using a minimal amount of water reduced dust generation, however, the formation of hard clumps was observed. To examine options and behavior, a TTQAP [McCabe and Stone, 2013] was written to initiate tests that would address these concerns. Tests were conducted with four types of glass frit; Frit 320, DWPF Frit 418, Bekeson Frit 418 and Multi-Aspirator Frit 418. The last two frits are chemically identical to DWPF Frit 418 but smaller particles were removed by the respective vendors. Test results on Frit Clumping and Dusting are provided in this report. This report addresses the following seven questions. Short answers are provided below with more detailed answers to follow. 1. Will the addition of a small amount of water, 1.5 wt%, to dry DWPF Frit 418 greatly reduce the dust generation during handling at DWPF? a. Yes, a small scale test showed that adding a little water to the frit greatly reduced dust generation during handling. 2. Will the addition of small amounts of water to the frit cause clumping that will impair frit handling at DWPF? a. No, not with Frit 418. Although clumps were observed to form when 1.5 wt% water was mixed with DWPF Frit 418, then compressed and air-dried overnight, the clumps were easily crushed and did not form the hardened material noted when Frit 320 was tested. 3. What is the measured size distribution of dust generated when dry frit is handled? (This affects the feasibility and choice of processing equipment for removing the dust generating fraction of the frit before it is added to the SME.) a. The size distribution for the dust removed from fresh DWPF Frit 418 while it was being shaken in a small scale LabRAM test was measured. The median size on a volume basis was 7.6 μm and 90% of the frit particles were between 1.6 and 28 μm. The mass of dust collected using this test protocol was much less than 1% of the original frit. 4. Can the dust be removed in a small number of processing steps and without the larger frit particles continuing to spall additional dust sized particles? a. Test results using a LabRAM were inconclusive. The LaRAM performs less efficient particle size separation than the equipment used by Bekeson and Multi-Aspirator. 5. What particle size of frit is expected to create a dust problem? a. The original criterion for creating a dusting problem was those particle sizes that were readily suspended when being shaken. For that criterion calculations and Microtrac size analyses indicated that particles smaller than 37 μm are likely dust generators. Subsequently a more sophisticated criterion for dust problem was considered, particle sizes that would become suspended in the air flow patterns inside the SME and possibly plug the condenser. That size may be larger than 37 μm but has not yet been determined. 6. If particles smaller than 37 μm are removed will bulk dust generation be eliminated? a. Video-taped tests were performed using three gallons each of three types of frit 418, DWPF frit, Bekeson frit and Multi-Aspirator frit. Frit was poured through air from a height of approximately eight feet into a container half filled with water. Pouring Bekeson frit or Multi-Aspirator frit generated markedly less visible dust, but there was still a significant amount, which still has the potential of causing a dust problem. 7. Can completely dry frit be poured into the SME without having dust plug the condenser at the top of the vessel? a. Because of the complexity of air currents inside the SME and the difficulty of defensible size scaling a more prototypical test will be required to answer this question. We recommend construction of a full scale mockup of the top half of the SME with a shallow basin of water at the bottom and a simulated condenser at the top. It could be made from simple materials such as PVC pipe, cardboard and clear plastic and tested with dry frit. Depending on results, this may need to be coupled with the proposed pneumatic transfer system.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Alternate Reductant Cold Cap Evaluation Furnace Phase I Testing

Savannah River Remediation (SRR) conducted a Systems Engineering Evaluation (SEE) to determine the optimum alternate reductant flowsheet for the Defense Waste Processing Facility (DWPF). Specifically, two proposed flowsheets (nitric–formic–glycolic and nitric–formic–sugar) were evaluated based upon results from preliminary testing. Comparison of the two flowsheets among evaluation criteria indicated a preference towards the nitric–formic–glycolic flowsheet. Further evaluation of this flowsheet eliminated the formic acid, and as a result, the nitric–glycolic flowsheet was recommended for further testing.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Samuel P. Massie Chair of Excellence In Environmental Disciplines: Hampton University 1994-2010 Year Report

The establishment of the DOE-EM Dr. Samuel P. Massie Chair of Excellence provides an excellent opportunity for Hampton University to be involved in key environmental issues in the 21 st Century. The main areas of focus are on: 1. Coal gasification with respect to pollution prevention and reduction. 2. Solid waste treatment through bioremediation technology and 3. Industrial wastewater treatment Synthesizing ion catalysts suitable for use in slurry bubble column reaction was carried out. Construction of an autoclave continuous stirred tank reactor has been completed. At the initial stage of the development of this program, work was conducted in the area of formic acid recovery from waste streams, which yielded useful results. We also succeeded in the removal of priority metal ions such as cadmium, chromium, copper, lead, mercury, nickel, silver, thallium, zinc, etc., from industrial and municipal wastewater by using natural wastes. The process uses tree leaves to adsorb the metal ions in the wastewater. The ultimate goal is to develop inexpensive, highly available, effective metal ion adsorbents from natural wastes as an alternative to existing commercial adsorbents, and also to explain the possible adsorption mechanism that is taking place. This technology uses natural wastes to eliminate other wastes. Obviously, there are several advantages: (1) the negative impact on environment is eliminated, (2) the complicated regeneration step is not needed, and (3) the procedure saves money and energy. Twelve different types of leaves have been tested with lead, zinc, and nickel. The study mechanism showed that the leaf tannin is an active ingredient in the adsorption of metal ions. The ion-exchange mechanism controlled the adsorption process.

42 ENGINEERING↗

Early Career Award: Decoupling the Electronic and Geometric Parameters of Metal Nanocatalysts

Central in many industrial processes (e.g., petroleum refining) and the realization of new energy platforms (e.g., fuel cells and biomass conversion) is heterogeneous catalysis. The performance of a catalyst is governed by interplay between electronic and geometric factors, but controlling these parameters to achieve efficient catalysis remains a grand challenge. The overall goal of this project was to decouple the electronic and geometric parameters of nanoscale metal catalysts for independent manipulation through the design and use of new architecturally controlled bimetallic nanocrystals. Specifically, shape-controlled core@shell nanocrystals were studied as catalysts. The binary composition of these structures provided a means of electronic control while the shape of the nanocrystals provided geometric control. Through a series of experiments with nanocrystals of different shapes and bimetallic compositions, the electronic and geometric parameters of such metal nanocatalysts were effectively decoupled for independent manipulation of catalyst performance. These concepts were applied toward new nanocatalysts for semihydrogenation, formic acid electrooxidation and for the oxygen reduction reaction. Ultimately, with the development of new synthetic strategies toward bimetallic nanocrystals, this research has advanced the design and synthesis of bimetallic nanocrystals as catalysts for diverse chemical transformations.

36 MATERIALS SCIENCE↗

Evaluation of Non-electric Market Options for a Light-water Reactor in the Midwest. Light Water Reactor Sustainability program

This study has addressed the technical feasibility and economic viability of LWR hybrid system operations based on realistic market around a specific reactor site in the Upper Midwest United States within the Great Lakes Region and near an industrial center that could benefit from more direct use of nuclear energy. The diverse industrial user and the electricity grid to optimize the revenue of the nuclear plant, depending on specific day-ahead electricity-grid capacity commitments and reserve capacity agreement requirements. For this market arrangement to work, the non-grid user is sold electricity without paying grid service fees (i.e., being considered a house load). This mode of energy sharing may require approval of governing utility commissions, depending on whether the hybrid operations can affect grid supply and manufacturing, agriculture, and transportation systems in this region provides several advantages to converting a nuclear plant into a hybrid plant that produces hydrogen and other feedstock commodities, such as polyethylene or formic acid, for example. Large-scale hydrogen production can essentially service several refineries within 20-30 miles of the nuclear plant. This would results in a measurable reduction of air-pollutant emissions reduction in the region. In addition, a large, consistent supply of hydrogen would draw new industries to the area—especially other steel-reduction and ammonia plants. For example, the nation’s first synthetic-fuels plant could also be sited near this hydrogen plant to convert CO 2 collected from the several ethanol plants in the region into methanol-based chemical feedstock and biofuels. With these perspectives in mind, this study has evaluated the business case for the following hybrid plant options.

08 HYDROGEN↗

Carbon Utilization: Electrochemical Approach Using Novel Catalyst and System Integration

The environmental footprint from power generation can be mitigated by capturing emitted carbon dioxide (CO2) and converting it to value-added fuel sources. A multitude of different fuels can be produced from CO2 depending on the chemical reaction catalysts. Typically, these pathways can be developed electrochemically, or through hydrogenation. In recent years the electrochemical reduction of CO2 has grown exponentially, as it has shown potential to decrease atmospheric pollution and provide an additional means of on-demand electricity storage. Formic acid (FA) in particular has industrial applications such as in fuel cells or as a hydrogen storage medium, and requires a lower thermodynamic energy input than any other fuel produced for electrochemical CO2 reduction. However, product selectivity remains a challenge for conventional electrocatalysts, making FA production efficiencies above 50% difficult. To address the challenge of catalytic selectivity, UK CAER employs enzymatic catalysts to facilitate the FA production and minimize unwanted byproducts. Our process couples the catalyst with a charge mediator which is necessary to shuttle electrons, and an electrolyte pH buffer to prevent the catalyst from degrading. Presently, production efficiencies have approached 60% at a rate of over 10 mM FA/hour. System design considerations (flow rate, bulk volume) will also be discussed.

01 COAL, LIGNITE, AND PEAT↗

Design of Efficient Molecular Electrocatalysts for Water and Carbon Dioxide Reduction Using Predictive Models of Thermodynamic Properties

Objectives: 1) To design and synthesize water soluble transition metal complexes that function as electrocatalysts for the reduction of water to hydrogen or carbon dioxide to formate 2) To experimentally measure thermochemical properties, such as hydride donor ability, and use these quantities to optimize catalyst performance in solutions of varying pH 3) To incorporate results from detailed mechanistic and kinetic studies to direct improvements in catalyst design 4) To use thermochemical data from objective 2 to generate predictive models for the properties of new complexes to apply to the development of catalysts for other reductive reactions, with an emphasis on carbon dioxide reduction to methanol Description: Wide-spread implementation of renewable but intermittent energy sources, such as solar, requires the development of efficient methods for energy storage. The high energy density of chemical bonds makes chemical fuels an ideal solution for energy storage. Hydrogen and reduced carbon compounds have been proposed as ideal candidates for chemical fuels. However, the generation of chemical fuels from electricity requires competent electrocatalysts. The proposed research focuses on developing electrocatalysts for the reduction of water to hydrogen, and carbon dioxide to formate. Both products can be used directly as an energy carrier in fuel cells, or as a reductant for more saturated chemical fuels. Hydrogen is the most common fuel used in current commercial fuel cells. Additionally, there is interest in formic acid as a liquid carrier for hydrogen because of its increased storage density and ease of dehydrogenation. Formate is also an intermediate in the sequential reduction of CO 2 to methanol, another potential chemical fuel with high energy storage density. Despite the utility of formate as a chemical fuel or precursor, there are very few examples of electrocatalysts for its production from CO 2 , and even fewer demonstrate high product selectivity. In heterogeneous catalysis, the Sabatier principle is used to generate volcano curves that describe optimal thermochemical properties for key intermediates that result in peak catalytic activity. In most cases, such as hydrogen production and oxidation, the most favorable metals (Pt, Re, Rh, and Ir) are rare and expensive. Molecular inorganic complexes provide an opportunity to use electronic and steric ligand effects to tune the critical thermodynamic parameters of abundant metals to values comparable to key surface intermediates on precious metals. This principle will be applied to the design of aqueous homogeneous catalysts for the reduction of H 2 O and CO 2 optimized to function at specific pH ranges. The critical intermediate in both of these reactions is a metal hydride. The strength of this bond, or hydricity (ΔGH - ) dictates the overall thermodynamics of the reduction of H + to H 2 and the sequential reduction of C1 substrates, such as CO 2 , CO, and H 2 CO (the latter to CH 3 OH). ΔGH - will be systematically measured for a series of first row metal complexes to form predictive models for metal and ligand electronic effects. Benefits and Outcomes: This approach addresses thermodynamic requirements essential for energy-efficient catalyst design and transition state barrier considerations for faster catalysis. The advancements made from this research will include the discovery of efficient, stable, and fast catalysts for hydrogen and formate generation from electricity. The ability to store energy efficiently is critical to the widespread use of renewable energy schemes. This provides a viable solution to produce high energy density fuels for stationary and mobile energy applications. The fundamental research conducted is also directly applicable to the design of catalysts for the generation of further reduced products such as methanol.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effective Biomass Fractionation through Oxygen-Enhanced Alkaline-Oxidative Pretreatment

The high recalcitrance of plant cell walls is an obstacle for effective chemical or biological conversion into renewable chemicals and transportation fuels. Here, we investigated the utilization of both oxygen (O 2 ) and hydrogen peroxide (H 2 O 2 ) as co-oxidants during alkalineoxidative pretreatment to improve biomass fractionation and increase enzymatic digestibility. The oxidative pretreatment of hybrid poplar was studied over a variety of conditions. Employing O 2 in addition to H 2 O 2 as a co-oxidant during the two-stage alkaline pre-extraction/coppercatalyzed alkaline hydrogen peroxide (Cu-AHP) pretreatment process resulted in a substantial improvement in delignification relative to using H 2 O 2 alone during the second-stage Cu-AHP pretreatment, leading to high overall sugar yields even at H 2 O 2 loadings as low as 2% (w/w of original biomass). The presence of H 2 O 2 , however, was both critical and synergistic. Performing analogous reactions in the absence of H 2 O 2 resulted in approximately 25% less delignification and a 30% decrease in sugar yields. The lignin isolated from this dual oxidant second stage had high aliphatic hydroxyl group content and reactivity to isocyanate, indicating that it is a promising substrate for the production of polyurethanes. To test the suitability of the isolated lignin as a source of aromatic monomers, the lignin was subjected to a sequential Bobbitt’s salt oxidation followed by formic-acid catalyzed depolymerization process. Monomer yields of approximately 17% (w/w) were obtained, and the difference in yields was not significant between lignin isolated from our Cu-AHP process with and without O 2 as a co-oxidant. Thus, the addition of O 2 did not lead to significant lignin crosslinking, a result consistent with the twodimensional heteronuclear single-quantum coherence (2D HSQC) NMR spectra of the isolated lignin.

09 BIOMASS FUELS↗

Upcycling Associated Natural Gas into Liquid Chemical Intermediates

This report assesses the opportunity to utilize associated natural gas (ANG) that is currently flared or vented by conversion to value-added chemicals. In cases where ANG production is not sufficient to justify on-site capture and added investments for transportation and storage, there may be commercial opportunities to perform conversion and value-added processing of ANG. This analysis focuses on CH 4 conversion to liquid intermediates, as opposed to gaseous product, due to the opportunity to transport large volumes of liquids, by truck or rail as opposed to pipeline. This report assesses market opportunities for four liquid intermediates: benzene, toluene, xylene, and formic acid.

03 NATURAL GAS↗

Electrochemical Reduction of Flue Gas Carbon Dioxide to Commercially Viable C2-C4 Products (Final Report)

This is the final scientific/technical report for a DOE project focused on the electrochemical conversion of CO 2 in non-aqueous solvents to novel products. Electrochemical reduction of CO 2 provides an attractive route to produce valuable fuels and chemicals that can simultaneously lower greenhouse gas emissions when powered by renewable electricity. While recent technological advances have shown the feasibility of industrial CO 2 electroreduction, many challenges remain to improve this technology and expand the list of economically viable products. The vast majority of electrochemical CO 2 reduction research has been conducted in aqueous media under neutral to alkaline conditions, leading to commonly reported products including carbon monoxide, formic acid, methane, methanol, ethylene, acetic acid, and ethanol. In comparison, non-aqueous media for CO 2 reduction has been underexplored but represents a possible avenue to yield new products and improved operating conditions. The aim of the project was to convert waste CO 2 in the form of flue gas to a multicarbon C2 - C4 chemical product in a reactor designed to achieve economically competitive values of current density and selectivity. The project strived to advance the technology readiness of an electrochemical CO 2 reduction process in alcohol solvents from the proof-of-concept stage to a device capable of meeting performance metrics for commercial viability. In the initial plan, the University of Louisville researchers were to focus on investigating the electrochemical process and improving the faradaic efficiency for novel C2 – C4 species, while also working on a parallel effort to build a practical electrolysis reactor to markedly increase the CO 2 reduction current density. The reactor development effort also aimed to engineer a dual-electrolyte feed strategy with non-aqueous catholyte and aqueous anolyte to promote water oxidation as the coupling anodic half-reaction to enable a sustainable and economical overall process. At the outset, the University of North Dakota was to investigate the feasibility of operating directly from coal-derived flue gas without separate capture and purification. The research team sought to determine impurity effects and test mitigation strategies, as well as engineer the gaseous feed system for high reactor tolerance to lower CO 2 concentration. In the last half year of the project, the focus was planned to shift to integrating the advances in the catalysis, electrochemical conditions, reactor design, and flue gas compatibility into a fully functional device and improve it for maximum current density and faradaic efficiency for C2 – C4 species. Knowledge of the full system components, constraints, and maximum performance was then to be used as the basis for a thorough technoeconomic analysis (TEA) and life cycle analysis (LCA) at the end of the project.

01 COAL, LIGNITE, AND PEAT↗

Analysis of the Sludge Batch 9 (Macrobatch 11) DWPF Pour Stream Glass Sample

A pour stream (PS) sample taken near the end of processing of Sludge Batch 9 (SB9, Macrobatch 11) with the Nitric-Formic Acid Flowsheet was analyzed by the Savannah River National Laboratory to comply with the Defense Waste Processing Facility (DWPF) Glass Product Control Program. The SB9 PS sample was taken on 5/28/2022 during Melter Feed Batch 815 associated with glass canister S04741, and was transferred to SRNL in Primary Container PC0136.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

ANION ANALYSES BY ION CHROMATOGRAPHY FOR THE ALTERNATE REDUCTANT DEMONSTRATION FOR THE DEFENSE WASTE PROCESSING FACILITY

The Process Science Analytical Laboratory (PSAL) at the Savannah River National Laboratory was requested by the Defense Waste Processing Facility (DWPF) to develop and demonstrate an Ion Chromatography (IC) method for the analysis of glycolate, in addition to eight other anions (fluoride, formate, chloride, nitrite, nitrate, sulfate, oxalate and phosphate) in Sludge Receipt and Adjustment Tank (SRAT) and Slurry Mix Evaporator (SME) samples. The method will be used to analyze anions for samples generated from the Alternate Reductant Demonstrations to be performed for the DWPF at the Aiken County Technology Laboratory (ACTL). The method is specific to the characterization of anions in the simulant flowsheet work. Additional work will be needed for the analyses of anions in radiological samples by Analytical Development (AD) and DWPF. The documentation of the development and demonstration of the method fulfills the third requirement in the TTQAP, SRNL-RP-2010-00105, 'Task Technical and Quality Assurance Plan for Glycolic-Formic Acid Flowsheet Development, Definition and Demonstrations Tasks 1-3'.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Catalytic Hydrogen Production from Methane: A Review on Recent Progress and Prospect

Natural gas (Methane) is currently the primary source of catalytic hydrogen production, accounting for three quarters of the annual global dedicated hydrogen production (about 70 M tons). Steam–methane reforming (SMR) is the currently used industrial process for hydrogen production. However, the SMR process suffers with insufficient catalytic activity, low long-term stability, and excessive energy input, mostly due to the handling of large amount of CO 2 coproduced. With the demand for anticipated hydrogen production to reach 122.5 M tons in 2024, novel and upgraded catalytic processes are desired for more effective utilization of precious natural resources. In this review, we summarized the major descriptors of catalyst and reaction engineering of the SMR process and compared the SMR process with its derivative technologies, such as dry reforming with CO 2 (DRM), partial oxidation with O 2 , autothermal reforming with H 2 O and O 2 . Finally, we discussed the new progresses of methane conversion: direct decomposition to hydrogen and solid carbon and selective oxidation in mild conditions to hydrogen containing liquid organics (i.e., methanol, formic acid, and acetic acid), which serve as alternative hydrogen carriers. We hope this review will help to achieve a whole picture of catalytic hydrogen production from methane.

08 HYDROGEN↗

Plasma Treating Mixed Metal Oxides to Improve Oxidative Performance via Defect Generation

The generation of structural defects in metal oxide catalysts offers a potential pathway to improve performance. Herein, we investigated the effect of thermal hydrogenation and low-temperature plasma treatments on mixed SiO 2 /TiO 2 materials. Hydrogenation at 500 °C resulted in the reduction of the material to produce Ti 3+ in the bulk TiO 2 . In contrast, low temperature plasma treatment for 10 or 20 min generated surface Ti 3+ species via the removal of oxygen on both the neat and hydrogenated material. Assessing the photocatalytic activity of the materials demonstrated a 40–130% increase in the rate of formic acid oxidation after plasma treatment. A strong relationship between the Ti 3+ content and catalyst activity was established, although a change in the Si–Ti interaction after plasma treating of the neat SiO 2 /TiO 2 material was found to limit performance, and suggests that performance is not determined solely by the presence of Ti 3+ .

36 MATERIALS SCIENCE↗

Cloud response to co-condensation of water and organic vapors over the boreal forest

Abstract. Accounting for the condensation of organic vapors along with water vapor (co-condensation) has been shown in adiabatic cloud parcel model (CPM) simulations to enhance the number of aerosol particles that activate to form cloud droplets. The boreal forest is an important source of biogenic organic vapors, but the role of these vapors in co-condensation has not been systematically investigated. In this work, the environmental conditions under which strong co-condensation-driven cloud droplet number enhancements would be expected over the boreal biome are identified. Recent measurement technology, specifically the Filter Inlet for Gases and AEROsols (FIGAERO) coupled to an iodide-adduct chemical ionization mass spectrometer (I-CIMS), is utilized to construct volatility distributions of the boreal atmospheric organics. Then, a suite of CPM simulations initialized with a comprehensive set of concurrent aerosol observations collected in the boreal forest of Finland during spring 2014 is performed. The degree to which co-condensation impacts droplet formation in the model is shown to be dependent on the initialization of temperature, relative humidity, updraft velocity, aerosol size distribution, organic vapor concentration, and the volatility distribution. The predicted median enhancements in cloud droplet number concentration (CDNC) due to accounting for the co-condensation of water and organics fall on average between 16 % and 22 %. This corresponds to activating particles 10–16 nm smaller in dry diameter that would otherwise remain as interstitial aerosol. The highest CDNC enhancements (ΔCDNC) are predicted in the presence of a nascent ultrafine aerosol mode with a geometric mean diameter of ∼ 40 nm and no clear Hoppel minimum, indicative of pristine environments with a source of ultrafine particles (e.g., via new particle formation processes). Such aerosol size distributions are observed 30 %–40 % of the time in the studied boreal forest environment in spring and fall when new particle formation frequency is the highest. To evaluate the frequencies with which such distributions are experienced by an Earth system model over the whole boreal biome, 5 years of UK Earth System Model (UKESM1) simulations are further used. The frequencies are substantially lower than those observed at the boreal forest measurement site (< 6 % of the time), and the positive values, peaking in spring, are modeled only over Fennoscandia and the western parts of Siberia. Overall, the similarities in the size distributions between observed and modeled (UKESM1) are limited, which would limit the ability of this model, or any model with a similar aerosol representation, to project the climate relevance of co-condensation over the boreal forest. For the critical aerosol size distribution regime, ΔCDNC is shown to be sensitive to the concentrations of semi-volatile and some intermediate-volatility organic compounds (SVOCs and IVOCs), especially when the overall particle surface area is low. The magnitudes of ΔCDNC remain less affected by the more volatile vapors such as formic acid and extremely low- and low-volatility organic compounds (ELVOCs and LVOCs). The reasons for this are that most volatile organic vapors condense inefficiently due to their high volatility below the cloud base, and the concentrations of LVOCs and ELVOCs are too low to gain significant concentrations of soluble mass to reduce the critical supersaturations enough for droplet activation to occur. A reduction in the critical supersaturation caused by organic condensation emerges as the main driver of the modeled ΔCDNC. The results highlight the potential significance of co-condensation in pristine boreal environments close to sources of fresh ultrafine particles. For accurate predictions of co-condensation effects on CDNC, also in larger-scale models, an accurate representation of the aerosol size distribution is critical. Further studies targeted at finding observational evidence and constraints for co-condensation in the field are encouraged.

54 ENVIRONMENTAL SCIENCES↗

Experimental interstellar organic chemistry: Preliminary findings

In a simulation of interstellar organic chemistry in dense interstellar clouds or on grain surfaces, formaldehyde, water vapor, ammonia and ethane are deposited on a quartz cold finger and ultraviolet-irradiated in high vacuum at 77K. The HCHO photolytic pathway which produces an aldehyde radical and a superthermal hydrogen atom initiates solid phase chain reactions leading to a range of new compounds, including methanol, ethanol, acetaldehyde, acetonitrile, acetone, methyl formate, and possibly formic acid. Higher nitriles are anticipated. Genetic relations among these interstellar organic molecules (e.g., the Cannizzaro and Tischenko reactions) must exist. Some of them, rather than being synthesized from smaller molecules, may be degradation products of larger organic molecules, such as hexamethylene tetramine, which are candidate consitituents of the interstellar grains. The experiments reported here may also be relevant to cometary chemistry.

Khare, B. N.↗

Research investigation directed toward extending the useful range of the electromagnetic spectrum

The lifetimes and fine structure of He(-) were studied using time-of-flight techniques and quenching by a static axial magnetic field. Using level-crossing spectroscopy the hyperfine constants A and B and the lifetime of the 3 2P3/2 state of Li-7 were measured. Polarization of the Ru 7S level was created as a first step in determining the hyperfine structure of the alkali excited S state. The parametric interaction between light and microwaves in optically pumped Rb-87 vapor were investigated. Measurements and analyses of transitions in formaldehyde and its isotopic species and in the lowest two excited vibrational states of H2CO were also made, as well as of transitions in furan, pyrrole, formic acid, and cyanoacetylene. The Hanle effect was studied in the NO molecule, and RF oscillators were developed with flat, wideband output to observe excited state hyperfine transitions at zero field. Data was generated on the time-dependent behavior of photon echoes in ruby. Stimulated Raman scattering was studied in atomic Tl vapor. A Q switched, temperature-tuned ruby laser was developed which operates between 6934 and 6938 A. The frequency shift due to resonant interaction between identical radiating atoms was calculated.

Hartmann, S. R.↗