Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Electron diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Application of Electron Backscatter Diffraction to evaluate the ASR risk of concrete aggregates

Alkali-Silica Reaction (ASR) is a frequent cause of reduced concrete durability. Eliminating the application of alkali reactive aggregates would reduce the quantity of ASR concrete deterioration in the field. This study introduces an Electron Backscatter Diffraction (EBSD) technique to distinguish the ASR risk of slow-late reacting aggregates by measuring microstructural properties of quartz. Quantifying the amount of quartz grain boundaries and the associated misorientation of grains can thereby be used to differentiate microstructures bearing an ASR risk. It is also shown that dissolution of quartz in high pH environments occurs along quartz grain and subgrain boundaries. Results of EBSD analysis are compared with ASR performance testing on concrete prisms and optical light microscopy characterization of quartz microstructure. EBSD opens new possibilities to quantitatively characterize microstructure of quartz in concrete aggregates with respect to ASR. This leads to a better understanding on the actual cause of ASR.

36 MATERIALS SCIENCE↗

Electron Backscatter Diffraction of a Ge Growth Tip from a Vertical Gradient Freeze Furnace

The growth-tip region of a high-purity 4.2-cm diameter Ge boule grown using low-pressure Bridgman methods in a vertical gradient freeze furnace was sectioned and polished in preparation for scanning electron microscopy and was characterized using electron backscatter diffraction (EBSD). The boule had a characteristic conical tip region with cone angle of 40° of a right circular cylinder from which a section was taken along the boule longitudinal centerline with an approximate surface area of 4 cm 2 . The majority of this surface area was characterized using EBSD and an image collage was assembled for the tip region. The grain structure, grain boundary orientation, twin structure, and overall crystal growth direction were determined. A crystal growth direction of approximately <112> was observed, which was also identified as the growth direction of several prominent twins observed in the tip region. The grain structure of the tip region appeared to be controlled by the sidewall nucleation of a stray grain that competed for dominance during growth. Grain boundaries and triple grain junctions were identified as low-energy coincident-site-lattice (CSL) boundaries and junctions of the Σ3 and Σ9 types.

36 MATERIALS SCIENCE↗

Determination of grain boundary mobility during recrystallization by statistical evaluation of electron backscatter diffraction measurements

One of the key aspects influencing microstructural design pathways in metallic systems is grain boundary motion. The present work introduces a method by means of which direct measurement of grain boundary mobility vs. misorientation dependence is made possible. The technique utilizes datasets acquired by means of serial electron backscatter diffraction (EBSD) measurements. The experimental EBSD measurements are collectively analyzed, whereby datasets were used to obtain grain boundary mobility and grain aspect ratio with respect to grain boundary misorientation. The proposed method is further validated using cellular automata (CA) simulations. Single crystal aluminium was cold rolled and scratched in order to nucleate random orientations. Subsequent annealing at 300 °C resulted in grains growing, in the direction normal to the scratch, into a single deformed orientation. Growth selection was observed, wherein the boundaries with misorientations close to Σ7 CSL orientation relationship (38° 〈111〉) migrated considerably faster. The obtained boundary mobility distribution exhibited a non-monotonic behavior with a maximum corresponding to misorientation of 38° ± 2° about 〈111〉 axes ± 4°, which was 10–100 times higher than the mobility values of random high angle boundaries. Correlation with the grain aspect ratio values indicated a strong growth anisotropy displayed by the fast growing grains. The observations have been discussed in terms of the influence of grain boundary character on grain boundary motion during recrystallization. - Highlights: • Statistical microstructure method to measure grain boundary mobility during recrystallization • Method implementation independent of material or crystal structure • Mobility of the Σ7 boundaries in 5N Al was calculated as 4.7 × 10{sup –8} m{sup 4}/J ⋅ s. • Pronounced growth selection in the recrystallizing nuclei in Al • Boundary mobility values during recrystallization 2–3 orders of magnitude larger vis-à-vis curvature driven motion.

36 MATERIALS SCIENCE↗

Atomic structures determined from digitally defined nanocrystalline regions

Nanocrystallography has transformed our ability to interrogate the atomic structures of proteins, peptides, organic molecules and materials. By probing atomic level details in ordered sub-10 nm regions of nanocrystals, scanning nanobeam electron diffraction extends the reach of nanocrystallography and in principle obviates the need for diffraction from large portions of one or more crystals. Scanning nanobeam electron diffraction is now applied to determine atomic structures from digitally defined regions of beam-sensitive peptide nanocrystals. Using a direct electron detector, thousands of sparse diffraction patterns over multiple orientations of a given crystal are recorded. Each pattern is assigned to a specific location on a single nanocrystal with axial, lateral and angular coordinates. This approach yields a collection of patterns that represent a tilt series across an angular wedge of reciprocal space: a scanning nanobeam diffraction tomogram. Using this diffraction tomogram, intensities can be digitally extracted from any desired region of a scan in real or diffraction space, exclusive of all other scanned points. Intensities from multiple regions of a crystal or from multiple crystals can be merged to increase data completeness and mitigate missing wedges. It is demonstrated that merged intensities from digitally defined regions of two crystals of a segment from the OsPYL/RCAR5 protein produce fragment-based ab initio solutions that can be refined to atomic resolution, analogous to structures determined by selected-area electron diffraction. In allowing atomic structures to now be determined from digitally outlined regions of a nanocrystal, scanning nanobeam diffraction tomography breaks new ground in nanocrystallography.

36 MATERIALS SCIENCE↗

High-Performance LiNi0.5Mn1.5O4 Spinel Controlled by Mn3+ Concentration and Site Disorder

The influences of Mn3+ ions on the properties of high voltage spinel LiNi0.5Mn1.5O4 is systematically investigated in this work. The content of Mn3+ ions in the spinel is tuned by further annealing of the sample or partially substitution of Ni2+ in the lattice structure. The former decreases the amount of Mn3+ while the latter increases Mn3+ concentration, which has been confirmed by both X-ray diffraction (XRD) and electron diffraction analysis. It has also been experimentally and theoretically proven that Mn3+ ions are directly related to the disordering between Ni2+ and Mn4+ on the octahedral sites in the spinel structure which facilitates the transportation of Li+ ions especially at elevated current densities. An extremely cycling stability as well as good rate capability have been observed in the Cr-substituted spinel confirming that an appropriate amount of Mn3+ ions is the key for a high performance high voltage spinel.

36 MATERIALS SCIENCE↗

Nd-doped BiFeO{sub 3} ceramics with antipolar order

Bi{sub 1-x}Nd{sub x}FeO{sub 3} (0{<=}x{<=}0.2) ceramics have been investigated using x-ray diffraction (XRD) and electron diffraction (ED). XRD patterns for x{<=}0.1 were consistent with rhombohedral BiFeO{sub 3}, whereas those for x=0.15 and x=0.2 exhibited peak splitting and superlattice reflections representative of orthorhombic, antiferroelectric PbZrO{sub 3}. ED for the latter samples confirmed the presence of (1/4)(hk0) superlattice reflections typical of a PbZrO{sub 3}-like structure but additional superlattice reflections were observed at (1/4)(00l) yielding a {radical}2a,2{radical}2a,4a (where a is the pseudocubic lattice parameter) unit cell. The transition from rhombohedral BiFeO{sub 3} to the PbZrO{sub 3}-like structure implies a modification from polar to antipolar behavior.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Intercalation-Induced Topotactic Phase Transformation of Tungsten Disulfide Crystals

Recent research has demonstrated the potential for topological superconductivity, anisotropic Majorana bound states, optical nonlinearity, and enhanced electrochemical activity for transition metal dichalcogenides (TMDs) with a 2M structure. These unique TMD compounds exhibit metastability and, upon heating, undergo a transition to the thermodynamically stable 2H phase. The 2M phase is commonly made at high temperatures using traditional solid-state methods, and this metastability further complicates the growth of large 2M WS 2 crystals. Herein, a novel synthetic method was developed, focusing on a molten salt reaction to synthesize large 2H crystals and then inducing transformation to the 2M phase through intercalation and thermal treatment. The 2H crystals were intercalated via a room-temperature sodium naphthalenide solution, producing a previously unreported Na-intercalated 2H WS 2 phase. Thermal heating was required to facilitate the phase transition to the intercalated 2M crystal structure. This phase transition was studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), selected area electron diffraction (SAED), electron dispersive X-ray spectroscopy (EDS), and Raman spectroscopy, which confirmed the synthesis of the intercalated 2M phase. Upon deintercalation, crystal and powder samples showed superconductivity with a T c of 8.6–8.7 K, similar to previously reported values. The generality of this process was further demonstrated using alkali metal triethyl borohydride to intercalate 2H WS 2 and produced the desired 2M phase. This novel synthetic method has broad implications for discovering metastable phases in other TMD families and layered materials. Furthermore, separation of the intercalation and phase transition also has the potential to allow for large-scale synthesis of this technologically important phase with greater control over each step of the reaction.

36 MATERIALS SCIENCE↗

Disordered surface structure of an ultra-thin tin oxide film on Rh(100)

The composition and structure of an ultra-thin tin oxide film on Rh(100), prepared by the deposition of a submonolayer of tin followed by annealing in an O{sub 2} atmosphere, were examined by a combination of low-energy electron diffraction (LEED), Auger electron spectroscopy, X-ray photoemission spectroscopy (XPS), scanning tunneling microscopy (STM), and ab initio calculations based on density functional theory (DFT). Although the LEED pattern exhibited c(2 x 8) spots clearly, a uniform periodicity of the c(2 x 8) unit cell was not observed in the STM images. The bright dots that were observed periodically in the STM image were similar to those of the ultra-thin Sn{sub 2}O{sub 3} film on Rh(111) and formed a zigzag arrangement with the numerous point and line defects. The XPS study revealed that the Sn 3d{sub 5/2} peak of the tin oxide film on Rh(100) showed a metallic state as well as an oxide state that was between the SnO{sub 2} and SnO states. The structural models, which were based on the Sn{sub 2}O{sub 3} structure on Rh(111), were determined using DFT total energy calculations. The simulated STM images of the two slightly different honeycomb-chain models well reproduced the zigzag arrangement in the STM image. The STM image and XPS spectrum were interpreted using a combination of the two models.

36 MATERIALS SCIENCE↗

Cantilever stress measurements for pulsed laser deposition of perovskite oxides at 1000 K in an oxygen partial pressure of 10{sup −4} millibars

An in situ stress measurement setup using an optical 2-beam curvature technique is described which is compatible with the stringent growth conditions of pulsed laser deposition (PLD) of perovskite oxides, which involves high substrate temperatures of 1000 K and oxygen partial pressures of up to 1 × 10{sup −4} millibars. The stress measurements are complemented by medium energy electron diffraction (MEED), Auger electron spectroscopy, and additional growth rate monitoring by a quartz microbalance. A shielded filament is used to allow for simultaneous stress and MEED measurements at high substrate temperatures. A computer-controlled mirror scans an excimer laser beam over a stationary PLD target. This avoids mechanical noise originating from rotating PLD targets, and the setup does not suffer from limited lifetime issues of ultra high vacuum (UHV) rotary feedthroughs.

36 MATERIALS SCIENCE↗

ZnSiP2 Thin Film Growth for Si-Based Tandem Photovoltaics

ZnSiP 2 is a ternary III-V analog with 0.5% lattice mismatch with Si and a 2.1 eV band gap, in the appropriate range for a top cell on a Si-based tandem device. We have previously shown that ZnSiP 2 has many properties suitable for applications to Si-based tandem photovoltaics using bulk single crystals grown in a Zn flux. The favorable results obtained from characterization of bulk material encourage the development of ZnSiP 2 as a photovoltaic absorber. To pursue this development, we have constructed a thin film growth reactor. This reactor employs a combination of chemical vapor deposition, using silane and phosphine as precursor gases, and physical vapor deposition, using an effusion cell to evaporate elemental Zn. We will present the results of ZnSiP 2 film growth on (100) Si substrates. The composition, structure, and morphology of these films have been characterized by energy dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy, X-ray diffraction and transmission electron diffraction, and electron microscopy, respectively. These promising results represent significant advancement towards implementing ZnSiP 2 as a top cell material on Si-based tandem photovoltaics.

14 SOLAR ENERGY↗

Effect of cold deformation on the recrystallization behavior of FePd alloy at the ordering temperature using electron backscatter diffraction

In this study, the evolution of the recrystallization texture and microstructure was investigated after annealing of 50% and 90% cold-rolled FePd alloy at 530 °C. The FePd alloy was produced by vacuum arc melting in an atmosphere of 97% Ar and 3% H{sub 2}. The specimens were cold rolled to achieve 50% and 90% reduction in thickness. Electron backscatter diffraction measurements were performed on the rolling direction–normal direction section. With increased deformation from 50% to 90%, recrystallized texture transition occurs. For the 50% cold-rolled alloy, the preferred orientation is (0 1 0) [11 0 1], which is close to the cubic orientation after 400 h of annealing. For the 90% cold-rolled alloy, the orientation changes to (0 5 4) [22–4 5] after 16 h of annealing. - Highlights: • Texture and microstructure in cold-rolled FePd alloy was investigated during annealing using EBSD. • The recrystallized texture of 50% cold-rolled FePd is (0 1 0) [11 0 1] at 530 °C for 400 hours. • The recrystallized texture of 90% cold-rolled FePd is changed to (0 5 4) [22–4 5] at 530 °C after 16 hours.

36 MATERIALS SCIENCE↗

A new ordered triple Hollandite: Ba{sub 1.33}Sb{sub 2.66}Al{sub 5.33}O{sub 16}

Ba{sub 1.33}Sb{sub 2.66}Al{sub 5.33}O{sub 16} is a triple Hollandite, which crystallizes in a tetragonal cell (I4/m no. 87) with a=b=9.86090(5) A and c=8.77612(6) A. Its crystal structure was characterized using electron diffraction and X-ray powder diffraction; it is isotypic to K{sub 1.33}Mg{sub 3.11}Sb{sub 4.89}O{sub 16}, K{sub 1.76}Mg{sub 3.25}Sb{sub 4.75}O{sub 16} and to K{sub 1.8}Li{sub 2.45}Sb{sub 5.55}O{sub 16}. In the rutile chains of Ba{sub 1.33}Sb{sub 2.66}Al{sub 5.33}O{sub 16}, the ordering of Al and Sb atoms into unmixed sites induces the tripling of the c parameter compared to a 'single' Hollandite structure. The Ba{sup 2+} cations are dispersed along c, in the largest tunnels on non-split and fully occupied sites. They lie into Ba-Ba pairs separated by vacancies. Their regular arrangement has been confirmed by high resolution electron microscopy. Electrochemical experiments have also been performed in Li-ion cell but no Li insertion was detected. - Graphical Abstract: The new Ba{sub 1.33}Sb{sub 2.66}Al{sub 5.33}O{sub 16} triple Hollandite has been synthesized and characterized by X-ray diffraction, electron microscopy, and cyclic voltammetry. Highlights: > Synthesis of a new barium antimonium aluminium oxide with a Hollandite structure. > X-ray diffraction, electron microscopy and cyclic voltammetry studies. > Presence of cationic vacancies but no Li insertion activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Determining the sputter yields of molybdenum in low-index crystal planes via electron backscattered diffraction, focused ion beam and atomic force microscope

Previous literature has used several monocrystalline sputtering targets with various crystalline planes, respectively, to investigate the variations of the sputter yield of materials in different crystalline orientations. This study presents a method to measure the sputtered yields of Mo for the three low-index planes (100), (110), and (111), through using an easily made polycrystalline target. The procedure was firstly to use electron backscattered diffraction to identify the grain positions of the three crystalline planes, and then use a focused ion beam to perform the micro-milling of each identified grain, and finally the sputter yields were calculated from the removed volumes, which were measured by atomic force microscope. Experimental results showed that the sputter yield of the primary orientations for Mo varied as Y{sub (110)} > Y{sub (100)} > Y{sub (111)}, coincidental with the ranking of their planar atomic packing densities. The concept of transparency of ion in the crystalline substance was applied to elucidate these results. In addition, the result of (110) orientation exhibiting higher sputter yield is helpful for us to develop a Mo target with a higher deposition rate for use in industry. By changing the deformation process from straight rolling to cross rolling, the (110) texture intensity of the Mo target was significantly improved, and thus enhanced the deposition rate. - Highlights: • We used EBSD, FIB and AFM to measure the sputter yields of Mo in low-index planes. • The sputter yield of the primary orientations for Mo varied as Y{sub (110)} > Y{sub (100)} > Y{sub (111)}. • The transparency of ion was used to elucidate the differences in the sputter yield. • We improved the sputter rate of polycrystalline Mo target by adjusting its texture.

36 MATERIALS SCIENCE↗

Electron Backscattered Diffraction Study of Microstructural Evolution During Isothermal Deformation of High-N Mn18Cr18 Alloy

In order to understand the dynamic recrystallization (DRX) mechanism of Mn18Cr18N austenitic stainless steel during hot deformation, the investigation of microstructure evolution is significant. Isothermal compression tests were conducted on a Gleeble-3500 thermomechanical simulator in the temperature range of 950 °C to 1150 °C and strain rate range between 0.001 and 1 s{sup −1}. Optical microscopy (OM) and electron backscattered diffraction (EBSD) were employed to study the resultant microstructures. More grain boundary information of hot-deformed specimens was provided by EBSD. It was found that the fraction of low-angle grain boundaries (LAGBs) increases with the decrease of deformation temperature or the increase of strain rate and can be expressed as a function of the Zener–Hollomon parameter. DRX easily occurs at the high deformation temperature and low strain rate. From the flow stress curves, the occurrence of single peak behavior and multiple transient steady-state (MTSS) behavior illustrated the existence of different DRX mechanisms. The EBSD analysis indicated that both continuous dynamic recrystallization (CDRX) and discontinuous dynamic recrystallization (DDRX) existed during hot deformation. For the low fraction of 10 to 15 deg misorientation, CDRX is the minor DRX mechanism while DDRX is the major DRX mechanism for the studied steel.

36 MATERIALS SCIENCE↗

Nanoscale-correlated octahedral rotations in BaZrO 3

BaZrO 3 is reportedly one of few perovskites that retains an ideal cubic structure down to zero Kelvin even though its ground state as predicted by first-principles calculations has remained contentious. Here, we combine electron diffraction with total neutron scattering measured on ceramic samples at cryogenic temperatures to demonstrate that below 80 K, this compound undergoes a structural change associated with the onset of correlated out-of-phase rotations of [ZrO 6 ] octahedra. Here, the change is manifested in the appearance of weak but relatively sharp superlattice reflections at ½hkl (h, k, l = odd), which are readily detectable by electron diffraction. Atomistic structural refinements from the total neutron scattering data confirmed that these reflections are associated with octahedral tilting. The observed rotations are consistent with the a 0 a 0 c - type and feature a coherence length of about 3 nm. The average structure of BaZrO 3 , as seen by Bragg diffraction, remains cubic. According to the electron diffraction data, Nb-doped BaZrO 3 undergoes a similar structural transition but in this case, the tilting couldn't be recovered from the neutron scattering, suggesting that the distortions are smaller compared to those in the pure compound.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Direct observation of the intergrown {alpha}-phase in {beta}-TmAlB{sub 4} via high-resolution electron microscopy

A TmAlB{sub 4} crystal with a ThMoB{sub 4}-type ({beta}-type) structure phase related to a hexagonal AlB{sub 2}-type structure was studied by electron diffraction and high-resolution electron microscopy. A high-resolution image clearly exhibits an intergrown lamellar structure of a YCrB{sub 4}-type ({alpha}-type) phase in the matrix of the {beta}-type phase in TmAlB{sub 4} crystal. The lamellar structure can be characterized by a tiling of deformed hexagons, which are a common structure unit in the {alpha}-type and {beta}-type structures. The intergrown nanostructure is considered to be attributed to the origin of low temperature anomalies in physical properties.

36 MATERIALS SCIENCE↗

Transmission electron microscope studies of extraterrestrial materials

Transmission Electron Microscopy, X-Ray spectrometry and electron-energy-loss spectroscopy are used to analyse carbon in interplanetary dust particles. Optical micrographs are shown depicting cross sections of the dust particles embedded in sulphur. Selected-area electron diffraction patterns are shown. Transmission Electron Microscope specimens of lunar soil were prepared using two methods: ion-milling and ultramicrotomy. A combination of high resolution TEM imaging and electron diffraction is used to characterize the opaque assemblages. The opaque assemblages analyzed in this study are dominated by ilmenite with lesser rutile and spinel exsolutions, and traces of Fe metal.

Keller, Lindsay P.↗