Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Effective temperature model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Synergistic Effects of Physical Aging and Damage on Long-Term Behavior of Polymer Matrix Composites

The research consisted of two major parts, first modeling and simulation of the combined effects of aging and damage on polymer composites and secondly an experimental phase examining composite response at elevated temperatures, again activating both aging and damage. For the simulation, a damage model for polymeric composite laminates operating at elevated temperatures was developed. Viscoelastic behavior of the material is accounted for via the correspondence principle and a variational approach is adopted to compute the temporal stresses within the laminate. Also, the effect of physical aging on ply level stress and on overall laminate behavior is included. An important feature of the model is that damage evolution predictions for viscoelastic laminates can be made. This allows us to track the mechanical response of the laminate up to large load levels though within the confines of linear viscoelastic constitutive behavior. An experimental investigation of microcracking and physical aging effects in polymer matrix composites was also pursued. The goal of the study was to assess the impact of aging on damage accumulation, in ten-ns of microcracking, and the impact of damage on aging and viscoelastic behavior. The testing was performed both at room and elevated temperatures on [+/- 45/903](sub s) and [02/903](sub s) laminates, both containing a set of 90 deg plies centrally located to facilitate investigation of microcracking. Edge replication and X-ray-radiography were utilized to quantify damage. Sequenced creep tests were performed to characterize viscoelastic and aging parameters. Results indicate that while the aging times studied have limited ]Influence on damage evolution, elevated temperature and viscoelastic effects have a profound effect on the damage mode seen. Some results are counterintuitive, including the lower strain to failure for elevated temperature tests and the catastrophic failure mode observed for the [+/- 45/9O3](sub s), specimens. The fracture toughness for transverse cracks increases with increasing temperature for both systems: transverse cracking was completely absent prior to failure in [+/- 45/903](sub s), and was suppressed for [02/903](sub s). No significant effect of damage on aging or viscoelastic parameters was observed.

Brinson, L. Cate↗
DOE OSTI2020

TEMPEST (Thermo-Electric Model for Powering Energy Storage Technologies)

NREL's TEMPEST model combines electrical and thermal modeling for residential-scale battery systems. The model and default parameters are based off of two common commercial residential batteries. Key inputs to the model include house load, temperature of the battery location, and the solar profile. The key output of the TEMPEST model is the battery profile and internal battery temperature. If internal battery temperature exceeds limits, a derating will occur and this will be reflected in the battery profile. In addition to thermal modeling, the TEMPEST model uses realistic operating principals that are common in today's residential batteries. Mainly, the TEMPEST model incorporates "modes" of operation that constrain battery setpoint based on house load, solar output, and state of charge. The TEMPEST model can be used to analyze the effect of battery temperature, deratings, and mode setpoints on utility network loading and customer bills.

Blonsky, Michael↗
NASA NTRS1985

Atmospheric planetary wave response to external forcing

The tools of observational analysis, complex general circulation modeling, and simpler modeling approaches were combined in order to attack problems on the largest spatial scales of the earth's atmosphere. Two different models were developed and applied. The first is a two level, global spectral model which was designed primarily to test the effects of north-south sea surface temperature anomaly (SSTA) gradients between the equatorial and midlatitude north Pacific. The model is nonlinear, contains both radiation and a moisture budget with associated precipitation and surface evaporation, and utilizes a linear balance dynamical framework. Supporting observational analysis of atmospheric planetary waves is briefly summarized. More extensive general circulation models have also been used to consider the problem of the atmosphere's response, especially in the horizontal propagation of planetary scale waves, to SSTA.

Stevens, D. E.↗
DOE OSTI2022

Microwave Heating-Induced Temperature Gradients in Liquid–Liquid Biphasic Systems

Microwaves (MWs) can enable the electrification and intensification of chemical manufacturing. They have been applied to various unit separations, such as drying, distillation, and extraction, entailing gas–liquid and solid–liquid systems. However, a limited quantitative understanding of MW-heated liquid–liquid biphasic systems related to extraction exists. This work measures the temporal and spatial temperature difference between an aqueous and an organic phase in batch and continuous microfluidic modes. We demonstrate permanent temperature differences between phases over 35 °C and spatiotemporal periodic and quasiperiodic oscillations modulated by the flow patterns. The temperature differences are primarily driven by the faster absorption rate of MW irradiation by the aqueous phase versus the slower heat transfer from the aqueous phase to the organic phase. These are amplified by low specific interfacial area and modifications of the electromagnetic field. We employ a multiphysics model to predict the temperature difference in a batch system. The model is in good agreement with the experiments. We demonstrate a strong effect of input power, dielectric properties of organic solvents, the volume of solvents, and the volume ratio between phases on the temperature difference. A simple analytical model describes the temperature difference and provides design principles. Furthermore, the combined approach offers new insights into the design and optimization of the MW-heated biphasic systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Modeling and design of a separate effects irradiation test targeting fission gas release from Cr-doped UO 2

Fission gas release (FGR) from nuclear fuel during operation can diminish heat transfer properties across the pellet-cladding gap and increase the fuel rod internal pressure, thereby posing a concern to fuel reliability and safety during an accident. Enlarging the fuel grain size, which has been shown to improve fission gas retention, can be achieved by doping the fuel feedstock prior to sintering. In this work, the BISON fuel performance code was used to predict FGR from undoped and chromia-doped UO 2 (referred to as Cr-doped UO 2 ) fuel specimens with different grain sizes and across various temperatures. The BISON models identified the irradiation conditions for which FGR is most significant, and a separate effects irradiation experiment in the High Flux Isotope Reactor (HFIR) was then developed targeting those conditions. Further, the experiment leveraged the MiniFuel irradiation capability at Oak Ridge National Laboratory and consisted of 12 fuel specimens of varying grain size and Cr content. A coupling scheme between BISON FGR results and the ANSYS finite element thermal model used for experiment design was formulated to predict cumulative FGR from each fuel specimen based on expected irradiation temperature histories. The fuel samples were fabricated and characterized as a part of this work, and the fuel compositions modeled in BISON were representative of the specimens used in the experiment. This combined modeling and experimental effort aims to study the effect of fuel grain size and Cr content on FGR and to provide simulated BISON FGR results that can be used for future model validation activities.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1999

The Atmospheric Effects of HSCT Emissions Simulated by a 3-Wave Interactive Model

An interactive model which couples a semi-spectral dynamical model, a radiative transfer code and a two-dimensional chemistry transport model (2-D CTM), is used to assess the atmospheric effects of the High-Speed Civil Transport (HSCT) engine emissions. The residual mean meridional circulation, the zonal-mean temperature and the eddy diffusion coefficients are calculated using zonal means and three longest zonal waves of dynamical variables integrated in the semi-spectral dynamical model. They are used in the 2-D CTM to simulate the distribution of trace gases in the atmosphere. The simulated ozone is sent to the radiative transfer code to calculate the heating rates, which drive the dynamics. This radiative coupling connects the dynamical and photochemical processes and creates feedback when the atmosphere is perturbed. It is found that in most areas the ozone depletion caused by HSCT emissions calculated using the 3-wave model has the features similar to, but with significantly larger magnitude than that calculated by the AER 2-D CTM with prescribed transport parameters and temperature. The difference is mostly due to the differences in the circulation in the two models. The radiative feedback effects are investigated by comparing the ozone depletion calculated with the baseline dynamics and with the dynamics perturbed by the HSCT emissions. The feedback through changes in the residual mean meridional circulation and the eddy diffusion coefficients has moderate effects on the simulated ozone depletion. It reduced the ozone depletion by 20-30% in northern mid and high-latitudes. However, the feedback through changes in the zonal- mean temperature is negligible.

Shia, R.-L.↗
NASA NTRS2021

PRELIMINARY MODEL FOR SOIL MOISTURE RETRIEVAL USING P-BAND RADIOMETER OBSERVATIONS

Soil Moisture is an important geophysical variable that needs reliable quantification for applications in hydrology, meteorology and agriculture. L-band radiometry has proved to be one of the best methods in soil moisture estimation using microwave signals. However, they provide measurements that correspond to a shallow depth of 5 cm and are also affected by the presence of overlaying vegetation and roughness. In contrast, P-band radiometry is expected to provide moisture information on a deeper layer of soil. Moreover, these lower frequency measurements are expected to be less affected by soil roughness and vegetation contributions. Consequently, this pilot study uses the Polarimetric P-band Multi beam Radiometer(PPMR) at 740 MHz to evaluate the response of theP-band radiometer over a realistic range of surface condition sat the field scale. A preliminary framework of P-band MicrowaveEmission of theBiosphere (P-MEB) has been developed as a forward model that simulates brightness temperature from soil moisture and other ancillary data collected from the field. This paper presents the model for the bare soil condition observed during June 2018 to August 2018. The results show that H-polarized PPMR data has better correlation to the soil moisture over a depth of 10 cm than the V-polarized PPMR data. A model is under improvement by incorporating a more suitable effective temperature formulation.

Edward J Kim↗
NASA NTRS1998

Comparison of Graphite Fabric Reinforced PMR-15 and Avimid N Composites After Long Term Isothermal Aging at Various Temperatures

Extensive effort is currently being expended to demonstrate the feasibility of using high-performance, polymer-matrix composites as engine structural materials over the expected operating lifetime of the aircraft, which can extend from 18,000 to 30,000 hr. The goal is to develop light-weight, high-strength, and high-modulus materials for use in higher temperature sections of advanced 21 st century aircraft propulsion systems. To accomplish this goal, it is necessary to pursue the development of thermal and mechanical durability models for graphite-fiber-reinforced, polymer-matrix composites. Numerous investigations have been reported regarding the thermo-oxidative stability (TOS) of the polyimide PMR-15 (1-5). A significant amount of this work has been directed at edge and geometry effects, reinforcement fiber influences, and empirical modeling of high-temperature weight loss behavior. It is yet to be determined if the information obtained from the PMR-15 composite tests is applicable to other polyimide-matrix composites. The condensation-curing polymer Avimid N is another advanced composite material often considered for structural applications at high temperatures. Avimid N has better thermo-oxidative stability than PMR-15 (6), but the latter is more easily processed. The most comprehensive study of the thermo-oxidative stability of Avimid N neat resin and composites at 371 (infinity)C is found in Salin and Seferis (7). The purposes of the work described herein were to compare the thermal aging behavior of these two matrix polymers and to determine the reasons for and the consequences of the difference in thermal durability. These results might be of some use in improving future polymer development through the incorporation of the desirable characteristics of both polyimides.

Bowles, Kenneth J.↗
NASA NTRS1991

Thermal analysis of conceptual designs for GPHS/FPSE power systems of 250 We and 500 We

Thermal analyses were performed for two distinct configurations of a proposed space nuclear power system which combines General Purpose Heat Source (GPHS) modules with the state of the art Free-Piston Stirling Engines (FPSEs). The two configurations correspond to systems with power levels of 250 and 500 W(sub e). The 250 W(sub e) GPHS/FPSE power system utilizes four GPHS modules and one FPSE, and the 500 W(sub e) contains eight GPHS modules and two FPSEs. The configurations of the systems and the bases for selecting the configurations are described. Brief introductory sections are included to describe the GPHS modules and free piston Stirling engines. The primary focus of the thermal analyses is on the temperature of the iridium fuel clad within the GPHS modules. A design goal temperature of 1573 K was selected as the upper limit for the fuel clad during normal operating conditions. The basis for selecting this temperature limit is discussed in detail. Results obtained from thermal analysis of the 250 W(sub e) GPHS/FPSE power system indicate fuel clad temperatures which slightly exceed the design goal temperature of 1573 K. The results are considered favorable due to the numerous conservative assumptions used in developing the thermal model and performing the thermal analysis. To demonstrate the effects of the conservatism, a brief sensitivity analysis is performed in which a few of the key system parameters are varied to determine their effect on the fuel clad temperatures. It is concluded that thermal analysis of a more detailed thermal model would be expected to yield fuel clad temperatures below the design foal temperature limiy 1573 K.

Mccomas, Thomas J.↗
DOE OSTI2025

Storms Are an Important Driver of Change in Tropical Forests

Tropical forest dynamics and composition have changed over recent decades, but the proximate drivers of these changes remain unclear. Investigations into these trends have focused on increasing drought stress, CO 2 , temperature, and fires, whereas convective storms are generally overlooked. We argue that existing literature provides clear support for the importance of storms as drivers of forest change. We reanalyze the largest plot-based study of tropical forest carbon dynamics to show that lightning frequency—an indicator of storm activity—strongly predicts forest carbon storage and residence time, and its inclusion improves model fit and weakens evidence for the effects of high temperatures. Convective storm activity has increased 5%–25% per decade over the past half century. Extrapolating from historic trends, we estimate that storms likely contribute ca. 50% of the reported increases in biomass mortality across Amazonia, with all realistic combinations of assumptions indicating a possible range of 12%–118%. Spatial variation in storm activity shows weak relationships with drought, demonstrating that forests can experience high drought stress, high storm activity, or both. Accordingly, we hypothesise that convective storms are among the most important drivers of tropical forest change, and as such, they require significant research investment to avoid misguiding science, policy, and management.

biomass carbon↗
NASA NTRS2000

A statistical model of the human core-temperature circadian rhythm

We formulate a statistical model of the human core-temperature circadian rhythm in which the circadian signal is modeled as a van der Pol oscillator, the thermoregulatory response is represented as a first-order autoregressive process, and the evoked effect of activity is modeled with a function specific for each circadian protocol. The new model directly links differential equation-based simulation models and harmonic regression analysis methods and permits statistical analysis of both static and dynamical properties of the circadian pacemaker from experimental data. We estimate the model parameters by using numerically efficient maximum likelihood algorithms and analyze human core-temperature data from forced desynchrony, free-run, and constant-routine protocols. By representing explicitly the dynamical effects of ambient light input to the human circadian pacemaker, the new model can estimate with high precision the correct intrinsic period of this oscillator ( approximately 24 h) from both free-run and forced desynchrony studies. Although the van der Pol model approximates well the dynamical features of the circadian pacemaker, the optimal dynamical model of the human biological clock may have a harmonic structure different from that of the van der Pol oscillator.

NASA Discipline Regulatory Physiology↗
NASA NTRS1981

A pocket model for aluminum agglomeration in composite propellants

This paper presents a model for the purpose of estimating the fraction of aluminum powder that will form agglomerates at the surface of deflagrating composite propellants. The basic idea is that the fraction agglomerated depends upon the amount of aluminum that melts within effective binder pocket volumes framed by oxidizer particles. The effective pocket depends upon the ability of ammonium perchlorate modals to encapsulate the aluminum and provide a local temperature sufficient to ignite the aluminum. Model results are discussed in the light of data showing effects of propellant formulation variables and pressure.

Cohen, N. S.↗
NASA NTRS1982

A model of the thermal-spike mechanism in graphite/epoxy laminates

The influence of a thermal spike on a moisture-saturated graphite/epoxy composite was studied in detail. A single thermal spike from 25 C to 132 C was found to produce damage as evidenced by a significant increase in the level of moisture saturation in the composite. Approximately half of this increase remained after a vacuum anneal at 150 C for 7 days, suggesting the presence of an irreversible damage component. Subsequent thermal spikes created less and less additional moisture absorption, with the cumulative effect being a maximum or limiting moisture capacity of the composite. These observations are explained in terms of a model previously developed to explain the reverse thermal effect of moisture absorption in epoxy and epoxy matrix composites. This model, based on the inverse temperature dependence of free volume, contributes an improved understanding of thermal-spike effects in graphite/epoxy composites.

Adamson, M. J.↗
NASA NTRSDate not supplied

Analysis of Cryogenic Propellant Liquefaction Rates in Cooled Constant-Wall-Temperature Tanks

NASA has been focused on developing technology that would allow the production of cryogenic propellants on the Lunar and Martian surfaces. Utilizing Lunar/Martian resources, the produced gaseous propellants must first be liquefied and stored prior to use on the Moon or Mars ascent vehicle. Liquefaction of cryogenic propellants is a necessary technical development to enable NASA’s future spaceflight goals. This paper presents an overview of a proposed model for a propellant liquefaction system, and the effect of tank wall temperatures on cryogenic propellant liquefaction rates. The propellant system was assumed to be a receiver of a gas from an In-Situ Resource Utilization (ISRU) harvester and condensed the gas by cooling the tank walls. First, the heat transfer principles pertinent to condensation are summarized, followed by an overview of the model which performed the analysis, including a summary of the Fortran algorithm implementation. The sensitivity of the condensation rate relative to varying tank wall temperatures is also discussed.

Anson Koch↗
DOE OSTI2020

Spectral Radiative Properties of Ceramic Particles for Concentrated Solar Thermal Energy Storage Applications

This work investigates the spectral radiative properties of ceramic particles using a monochromator and a Fourier-transform infrared spectrometer (FTIR) with integrating spheres at wavelengths from 0.38 μm to 15 μm. Particles are encased between two transparent windows to obtain the directional-hemispherical reflectance of the particle bed. Two types of commercially available particles with three different sizes are examined. Integration over the solar spectrum reveals that the solar absorptance of the particle beds is between 0.940 and 0.957. The total emittance at 1000 K is also estimated by assuming the spectral emittance is independent of temperature. The optical constants of particles are modeled with effective medium approaches, considering the optical properties of individual constituent materials. The absorptance of the particle is estimated using the effective optical constants and compared with that of the particle bed from the measurement. Finally, this work facilitates the characterization of radiative properties of particles with a windowed method and provides a modeling scheme for approximating the radiative properties of composite ceramic materials.

14 SOLAR ENERGY↗
DOE OSTI2020

Theoretical Investigation of Solvent Effects on the Hydrodeoxygenation of Propionic Acid over a Ni(111) Catalyst Model

The effect of two solvents, liquid water and 1,4-dioxane, has been studied from first principles on the hydrodeoxygenation of propionic acid over a Ni (111) catalyst surface model. A mean-field microkinetic model was developed to investigate these effects at a temperature of 473 K. Under all reaction conditions, a decarbonylation mechanism is favored significantly over a decarboxylation pathway. Although no significant solvent effects were observed on the decarbonylation rate, a substantial solvent stabilization of two key surface intermediates in the decarboxylation mechanism, CH 3 CCOO and CH 3 CHCOO, lead to a notable increase of the decarboxylation rate by two orders of magnitude in liquid water and by one order of magnitude in liquid 1,4-dioxane. Furthermore, a significant solvent stabilization of the transition state of C-H bond cleavage of the α-carbon of CH 3 CHCO, relative to the stabilization of the C-C bond cleavage of the α-carbon of CH 3 CHCO, leads to a change in dominant pathway in the liquid phase environments. Finally, a sensitivity analysis shows that the C-OH bond cleavage of propionic acid and C-C bond cleavage of the α-carbon of CH 3 CHCO are the most rate controlling states in the gas phase. In contrast, in solvents the dehydrogenation of CH 3 CHCO becomes the most influential step. This shift in rate controlling state is attributed to the solvent effect on the dehydrogenation of CH 3 CHCO, which is facilitated in aqueous phase. Altogether, it is likely that the investigated (111) facet of Ni is not active for the hydrodeoxygenation of propionic acid in neither the gas nor liquid phase and other Ni facets or phases must be responsible for the experimentally observed kinetics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Phase mediated dynamics of self-propagating Co/Al nanolaminate reactions

The ignition of sputter deposited nanolaminate foils comprised of alternating Co and Al layers results in rapid, self-propagating formation reactions. The propagating waves present after ignition of 150 nm-thick foils are characterized in movie mode dynamic transmission electron microscopy where these are found to have reaction speeds and wave morphology that vary with bilayer thickness. High speed videography reveals different bilayer thickness-wave character relationships in 750 nm- and 7500 nm-thick Co/Al foils. The reaction speed dependencies on bilayer thickness are calculated for each total thickness by treating the effect of radiation loss as a perturbation from an analytical model described by the difference in the heat of reaction measured in calorimetry and the adiabatic heat of product formation. From this model, an effective activation energy, diffusion constant, and flame temperatures are obtained, which allows for an interpretation of the reaction phase variations with laminate design and their effects on propagating wave morphology.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Quantum phase transitions in long-range interacting hyperuniform spin chains in a transverse field

Hyperuniform states of matter are characterized by anomalous suppression of long-wavelength density fluctuations. While most of the interesting cases of disordered hyperuniformity are provided by complex many-body systems such as liquids or amorphous solids, classical spin chains with certain long-range interactions have been shown to demonstrate the same phenomenon. Such spin-chain systems are ideal models for exploring the effects of quantum mechanics on hyperuniformity. It is well-known that the transverse field Ising model shows a quantum phase transition (QPT) at zero temperature. Under the quantum effects of a transverse magnetic field, classical hyperuniform spin chains are expected to lose their hyperuniformity. High-precision simulations of these cases are complicated because of the presence of highly nontrivial long-range interactions. We perform an extensive analysis of these systems using density matrix renormalization group simulations to study the possibilities of phase transitions and the mechanism by which they lose hyperuniformity. Even for a spin chain of length 30, we see discontinuous changes in properties like the “τ order metric” of the ground state, the measure of hyperuniformity, and the second cumulant of the total magnetization along the x-direction, all suggestive of first-order QPTs. An interesting feature of the phase transitions in these disordered hyperuniform spin chains is that, depending on the parameter values, the presence of a transverse magnetic field may lead remarkably to an increase in the order of the ground state as measured by the “τ order metric,” even if hyperuniformity is lost. Therefore, it would be possible to design materials to target specific novel quantum behaviors in the presence of a transverse magnetic field. Our numerical investigations suggest that these spin chains can show no more than two QPTs. We further analyze the long-range interacting spin chains via the Jordan-Wigner mapping onto a system of spinless fermions, showing that under the pairwise-interaction approximation and a mean-field treatment, there can be at most two quantum phase transitions. Here, based on these numerical and theoretical explorations, we conjecture that for spin chains with long-range pair interactions that have convergent cosine transforms, there can be a maximum of two quantum phase transitions at zero temperature.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗