Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EUTECTIC ALLOY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Effects of silicon on the oxidation, hot-corrosion, and mechanical behavior of two cast nickel-base superalloys

Cast specimens of nickel-base superalloys 713C and Mar-M200 with nominal additions of 0, 0.5, and 1 wt% Si were evaluated for oxidation and corrosion resistance, tensile and stress-rupture properties, microstructure, and phase relations. Results are compared with those of an earlier study of the effects of Si in B-1900. Si had similar effects on all three superalloys. It improves oxidation resistance but the improvement in 713C and Mar-M200 was considerably less than in B-1900. Hot-corrosion resistance is also improved somewhat. Si is, however, detrimental to mechanical properties, in particular, rupture strength and tensile ductility. Si has two obvious microstructural effects. It increases the amount of gamma-prime precipitated in eutectic nodules and promotes a Mo(Ni,Si)2 Laves phase in the alloys containing Mo. These microstructural effects do not appear responsible for the degradation of mechanical properties, however.

Miner, R. V., Jr.↗

Studies on copper alloys containing chromium on the copper side phase diagram

Specimens were prepared from vacuum melted alloys of high purity vacuum melted copper and electrolytic chromium. The liquidus and eutectic point were determined by thermal analysis. The eutectic temperature is 1974.8 F and its composition is 1.28 wt% of chromium. The determination of solid solubility of chromium in copper was made by microscopic observation and electrical resistivity measurement. The solubility of chromium in solid copper is 0.6 wt% at 1050 F, 0.4 wt% at 1000 F, 0.25 wt% at 950 F, 0.17 wt% at 900 F, and 0.30 wt% at 840 F.

Doi, T.↗

Microstructure and corrosion behavior of cast Fe-B alloys dipped into liquid zinc bath

The corrosion behavior of cast Fe-B alloys in a liquid zinc bath was examined. As a result, the as-cast Fe-3.5B alloy displays the best corrosion resistance in all tested specimens owing to its netlike structure of eutectic Fe{sub 2}B against the liquid zinc. XRD and EDS results indicate that the main phases in the corrosion layer are determined to be {delta}, {zeta} and {eta} from the matrix to the zinc zone, respectively. The corrosion process is controlled by the diffusion of zinc atoms and the dissolution mechanism. According to the observations, only three steps occur in the whole dissolution process: the preferential dissolution of {alpha}-Fe, the formation of intermetallic compounds, and the spalling of Fe{sub 2}B caused by cracks that mainly result from the internal stress produced by Fe/Zn phase transformation. The continuous netlike Fe{sub 2}B phase delays the further reaction of Fe/Zn and hinders the diffusion of zinc atoms between the substrate and liquid zinc effectively, improving corrosion resistance of Fe-B alloy in comparison with 1Cr18Ni9Ti stainless steel.

36 MATERIALS SCIENCE↗

Au, Ge and AuGe Nanoparticles Fabricated by Laser Ablation

A eutectic AuGe target immersed in distilled water was ablated by pulsed ultraviolet laser light. The structure of the ablated material was investigated by high-resolution transmission electron microscopy (HRTEM). The images show formation of nanowire structures of AuGe up to 100 nm in length, with widths of 5-10 nm. These nanostructures have Ge content significantly lower than the target material. Electron diffraction demonstrates that they crystallize in the {alpha}-AuGe structure. For comparison, laser ablation of pure Au and pure Ge targets was also performed under the same conditions. HRTEM shows that Ge forms spherical nanoparticles with a characteristic size of {approx}30 nm. Au forms spherical nanoparticles with diameters of {approx}10 nm. Similar to AuGe, it also forms chainlike structures with substantially lower aspect ratio.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Sr effect on the microstructure and tensile properties of A357 aluminum alloy and Al{sub 2}O{sub 3}/SiC-A357 cast composites

The effect of strontium as a modifier on the microstructures and tensile properties of two castable particulate metal matrix composites has been studied. The particulate metal matrix composites had similar matrix alloy (A357) but different reinforcing fine particles (silicon carbide and alumina). Results showed that the addition of 0.03% strontium makes a modest improvement to the yield strength, ultimate tensile strength and elongation percentage values, and the scatter of these properties, but makes a significant improvement to minimum strength and elongation results. Microstructural examinations by scanning electron microscope and energy dispersive spectroscopy analysis of metal matrix composites showed segregation of strontium on both the silicon carbide and alumina particles. Further results showed that the addition of higher strontium levels contributes to the over-modification of the eutectic silicon and promotes the formation of an Al-Si-Sr intermetallic compound on the particle/matrix interface.

36 MATERIALS SCIENCE↗

Cost/benefit studies of advanced materials technologies for future aircraft turbine engines: Materials for advanced turbine engines

Cost benefit studies were conducted on six advanced materials and processes technologies applicable to commercial engines planned for production in the 1985 to 1990 time frame. These technologies consisted of thermal barrier coatings for combustor and high pressure turbine airfoils, directionally solidified eutectic high pressure turbine blades, (both cast and fabricated), and mixers, tail cones, and piping made of titanium-aluminum alloys. A fabricated titanium fan blisk, an advanced turbine disk alloy with improved low cycle fatigue life, and a long-life high pressure turbine blade abrasive tip and ceramic shroud system were also analyzed. Technologies showing considerable promise as to benefits, low development costs, and high probability of success were thermal barrier coating, directionally solidified eutectic turbine blades, and abrasive-tip blades/ceramic-shroud turbine systems.

Stearns, M.↗

Thermodynamic Assessment of Hot Corrosion Mechanisms of Superalloys Hastelloy N and Haynes 242 in Eutectic Mixture of Molten Salts KF and ZrF4

The KF - ZrF4 system was considered for the application as a heat exchange agent in molten salt nuclear reactors (MSRs) beginning with the work carried out at ORNL in early fifties. Based on a combination of excellent properties such as thermal conductivity, viscosity in the molten state, and other thermo-physical and rheological properties, it was selected as one of possible candidates for the nuclear reactor secondary heat exchanger loop.

36 MATERIALS SCIENCE↗

Evaluating Iodine Immobilization Technologies: Cermets, Polycermets, and Polyhalmets

The work in this report documents the efforts conducted to assess the feasibility of some of the ideas documented in Pacific Northwest National Laboratory invention disclosure reports (IDRs) including: 1) Iodine capture in polyacrylonitrile (PAN)-containing composite sorbents (32451-E). In this work, the composites evaluated included Ag0, Bi0, Cu0, Bi2S3, and Cu2S embedded in PAN. 2) Metal iodide removal from these sorbents through dissolution in dimethyl sulfoxide (DMSO) (32729-E). In this work, PAN dissolution was evaluated for multiple types of sorbents including Ag-Pan, Bi-PAN, Cu-PAN, Bi2S3-PAN, and Cu2S-PAN. 3) Using metal-sulfide sorbents for iodine capture (32647-E). In this work, the composites evaluated under this IDR included Ag2S, Bi2S3, and Cu2S embedded in PAN. 4) Using low-melting metals to immobilize (encapsulate) iodine-loaded and polymer-containing sorbents into polymer-ceramic-metal (called polycermet) or polymer-halide-metal (called polyhalmet) composite waste forms (32625-E). In this work, the iodine-loaded PAN composites included AgI-PAN, BiI-PAN, and CuI-PAN. 5) Ceramic-metal composite waste form synthesis of polymer-containing materials using low-melting metals like bismuth, tin, or bismuth-tin alloys (32537-E). In this work, the metals evaluated included Bi, 58Bi-42Sn eutectic. 6) Cermets for immobilizing commercial sorbents loaded with radioiodine (32806-E). In this work, AgIX (iodine-loaded silver faujasite zeolite) was evaluated in cermet form.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Corrosion of oxide dispersion strengthened iron–chromium steels and tantalum in fluoride salt coolant: An in situ compatibility study for fusion and fusion–fission hybrid reactor concepts

Primary candidate classes of materials for future nuclear power plants, whether they be fission, fusion or hybrids, include oxide dispersion strengthened (ODS) ferritic steels which rely on a dispersion of nano-oxide particles in the matrix for both mechanical strength and swelling resistance, or tantalum alloys which have an inherent neutron-induced swelling resistance and high temperature strength. For high temperature operation, eutectic molten lithium containing fluoride salts are attractive because of their breeding capability as well as their relatively high thermal capacity, which allow for a higher average operating temperature that increases power production. In this paper we test the compatibility of Flinak (LiF–NaF–KF) salts on ODS steels, comparing the performance of current generation ODS steels developed at Kyoto University with the commercial alloy MA956. Additionally, pure tantalum was also tested for comparative purposes. In situ data was obtained for temperatures ranging from 600 to 900 °C using a custom-built high temperature electrochemical impedance spectroscopy cell. Results for ODS steels show that steel/coolant interfacial resistance increases from 600 to 800 °C due to an aluminum enriched layer forming at the surface, however an increase in temperature to 900 °C causes this layer to break up and aggressive attack to occur. Performance of current generation ODS steels surpassed that of the MA956 ODS steel, with an in situ impedance behavior similar or better than that of pure tantalum.

36 MATERIALS SCIENCE↗

Study on Microstructure and Properties of AZ31/6061 GTAW Butt Joints According to Mg-Cd-Al Ternary System

AZ31 Mg and 6061 Al were successfully joined by GTAW method with Cd as filler metal. The tensile strength of the joints reached 170 MPa through this alloying method according to Mg-Cd-Al ternary system. The microstructure, phases, element distribution and fracture mechanism of alloyed joints were studied. The results suggest that the fusion zone is mainly composed of CdMg compounds and Al-based solid solution. A transitional zone thickness of 40-80 μm with few primary Al{sub 12}Mg{sub 17} and fine Al{sub 12}Mg{sub 17}-MCMS (MCMS represents a mixture of CdMg and CdMg{sub 3} compounds) eutectic is formed between the AZ31 base metal and fusion zone. The fracture surface presents three distinct regions because of the different distribution of Al{sub 12}Mg{sub 17} compounds in the transitional zone. The alloying with Cd filler metal can disperse Al{sub 12}Mg{sub 17} intermetallic compounds and form CdMg ordered compounds with excellent plasticity. Thus, the mechanical properties of alloyed joints have been significantly enhanced.

36 MATERIALS SCIENCE↗

Relationships Between Solidification Parameters in A319 Aluminum Alloy

The design of high-performance materials depends on a comprehensive understanding of the alloy-specific relationships between solidification and properties. However, the inconsistent use of a particular solidification parameter for presenting materials characterization in the literature impedes inter-study comparability and the interpretation of findings. Therefore, there is a need for accurate expressions relating the solidification parameters for each alloy. In this study, A319 aluminum alloy castings were produced in a permanent mold with various preheating temperatures in order to control metal cooling. Analysis of the cooling curve for each casting enabled the identification of its liquidus, Al-Si eutectic, and solidus temperatures and times. These values led to the calculation of the primary solidification rate, total solidification rate, primary solidification time, and local solidification time for each casting, which were related to each other as well as to the average casting SDAS and material hardness. Expressions for each of their correlations have been presented with high coefficients of determination, which will aid in microstructural prediction and casting design.

36 MATERIALS SCIENCE↗

Thermodynamic properties of Gd-Bi alloys determined by emf measurements in LiCl-KCl-GdCl 3 electrolyte

Thermodynamic properties of binary Gd-Bi alloys (mole fraction, x Gd = 0.02–0.35) were determined using electromotive force (emf) measurements in molten LiCl-KCl-GdCl 3 electrolyte in complement with structural, microstructural, and thermal characterization. X-ray diffractometry (XRD) and scanning electron microscopy (SEM) identified the phase constituents of Gd-Bi alloys (x Gd = 0.02–0.35) as Bi matrix and GdBi compound. According to differential scanning calorimetry (DSC) measurements up to 1250 K, a eutectic transition [L = Bi + GdBi] was observed at 543 K but the reported peritectic transition [L + GdBi = GdBi 2 ] was not detected, suggesting the absence of the GdBi 2 compound. Based on structural, microstructural, and thermal characterization of Gd-Bi alloys (x Gd = 0.02–0.35), the GdBi 2 compound was not detected, and its thermodynamic stability is questionable. The emf of Gd-Bi alloy (x Gd = 0.16) at 700–1048 K relative to Gd(s) was measured by electrodepositing pure Gd metal at 25 K increments. Further, the emf values of Gd-Bi alloys were determined via coulometric titration of Gd into liquid Bi using a two-phase [L + GdBi] alloy as a reference electrode at 773–973 K. The solubility of Gd in liquid Bi was also estimated to be 0.50 mol% (773 K), 0.99 mol% (873 K), and 2.21 mol% (973 K) and the excess partial molar Gibbs energy (Δ$\mathrm{\bar{G}^{ex}_{Gd}}$) of liquid Gd-Bi alloys was as low as 65 kJ mol –1 , indicating strong chemical interactions between Gd and Bi.

36 MATERIALS SCIENCE↗

Preferred orientation relationships with large misfit interfaces between Ni{sub 3}Sn{sub 4} and Ni in reactive wetting of eutectic SnPb on Ni

Ni{sub 3}Sn{sub 4} grains were formed on Ni by reactive wetting between molten eutectic SnPb and thermally annealed Ni foil. Using synchrotron white beam micro x-ray diffraction analysis, two kinds of preferred orientation relationships between Ni{sub 3}Sn{sub 4} and Ni were found. The existence of preferred orientation with large interfacial misfit is suggested as a general mechanism of intermetallic compound formation in reactive solder wetting on metals.

36 MATERIALS SCIENCE↗

Some properties of low-vapor-pressure braze alloys for thermionic converters

Density, dc electrical resistivity, thermal conductivity, and linear thermal expansion are measured for arc-melted rod-shaped samples of binary eutectics of Zr, Hf, Ru, Nb, Ir, Mo, Ta, Os, Re, and W selected as very-low-pressure braze fillers for thermionic converters. The first two properties are measured at 296 K for Zr-21.7 at% Ru, Zr-13 wt% W, Zr-19 wt% W, Zr-22.3 at% Nb, Nb-66.9 at% Ru, Hf-25.3 wt% Re, Zr-25.7 at% Ta, Hf-22.5 at% W, and Nb-35 wt% Mo. The last property is measured from 293 K to 2/3 melting point for specified alloys of different compositions. Resistivities of 0.000055 to 0.000181 ohm-cm are observed with the alloys having resistivities about ten times that of the less resistive constituent metal and about three times that of the more resistive constituent metal, except for Zr-19 wt% W and Nb-35 wt% Mo (greater resistivities). Thermal expansion coefficients vary from 0.000006 to 0.0000105/K. All brazes exhibit linear thermal expansion near that of their constituent metals.

Bair, V. L.↗

Theoretical and experimental investigation of 'grating' type photovoltaic cells

The fabrication procedure and properties of 'grating' cells made by forming a fine grating pattern of aluminum alloyed into n-silicon wafers are described. The finest grating lines achieved in the cells described were 5 microns; the smallest spacing was about 15 microns. The best temperature for alloying was found to be about 600 C, a bit above the Si-Al eutectic temperature (576 C). The short-circuit current obtained from the best of these cells exposed to 100 mW/sq cm of (simulated air mass zero) illumination was at least equal to that obtained from conventional diffused cells, but their open-circuit voltage was lower. Their quantum yield was strongly blue-shifted; it was flat from 4000 to 8500 A.

Loferski, J. J.↗

Solidification and Re-melting Phenomena During Slurry Preparation Using the RheoMetal™ Process

The melting sequence of the enthalpy exchange material (EEM) and formation of a slurry in the RheoMetal™ process was investigated. The EEM was extracted and quenched, together with a portion of the slurry at different processing times before complete melting. The EEM initially increased in size/diameter due to melt freezing onto its surface, forming a freeze-on layer. The initial growth of this layer was followed by a period of a constant diameter of the EEM with subsequent melting and decrease of diameter. Microstructural characterization of the size and morphology of different phases in the EEM and in the freeze-on layer was made. Dendritic equiaxed grains and eutectic regions containing Si particles and Cu-bearing particles and Fe-rich particles were observed in the as-cast EEM. The freeze-on layer consisted of dendritic aluminum tilted by about 30 deg in the upstream direction, caused by the rotation of the EEM. Energy dispersion spectroscopy analysis showed that the freeze-on layer had a composition corresponding to an alloy with higher melting point than the EEM and thus shielding the EEM from the surrounding melt. Microstructural changes in the EEM showed that temperature rapidly increased to 768 K (495 °C), indicated by incipient melting of the lowest temperature melting eutectic in triple junction grain boundary regions with Al{sub 2}Cu and Al{sub 5}Mg{sub 8}Si{sub 6}Cu{sub 2} phases present. As the EEM temperature increased further the binary Al-Si eutectic started to melt to form a region of a fully developed coherent mushy state. Experimental results and a thermal model indicated that as the dendrites spheroidized near to the interface at the EEM/freeze-on layer reached a mushy state with 25 pct solid fraction, coherency was lost and disintegration of the freeze-on layer took place. Subsequently, in the absence of the shielding effect from the freeze-on Layer, the EEM continued to disintegrate with a coherency limit of a solid fraction estimated to be 50 pct.

36 MATERIALS SCIENCE↗

Atomized BaF2-CaF7 for Better-Flowing Plasma-Spray Feedstock

Atomization of a molten mixture of BaF2 and CaF2 has been found to be superior to crushing of bulk solid BaF2- CaF2 as a means of producing eutectic BaF2-CaF2 powder for use as an ingredient of the powder feedstock of a high-temperature solid lubricant material known as PS304. Developed to reduce friction and wear in turbomachines that incorporate foil air bearings, PS304 is applied to metal substrates by plasma spraying. The constituents of PS304 are: a) An alloy of 80 weight percent Ni and 20 weight percent Cr, b) Cr2O3, c) Ag, and d) The BaF2-CaF2 eutectic, specifically, 62 weight percent BaF2 and 38 weight percent CaF2. The superiority of atomization as a means of producing the eutectic BaF2-CaF2 powder lies in (1) the shapes of the BaF2-CaF2 particles produced and (2) the resulting flow properties of the PS304 feedstock powder: The particles produced through crushing are angular, whereas those produced through atomization are more rounded. PS304 feedstock powder containing the more rounded BaF2-CaF2 particles flows more freely and more predictably, as is preferable for plasma spraying.

DellaCorte, Christopher↗

Microstructure and In Situ Observations of Undercooling for Nucleation of [beta]-Sn Relevant to Lead-Free Solder Alloys

Difficult nucleation of {beta}-Sn during solidification of tin and tin-based lead-free solder alloys can result in high degrees of undercooling of the liquid prior to solidification. The undercooling can produce solder joints with large grains, anisotropic behavior, and undesirable mechanical properties. This paper describes our examination of the amount of undercooling of tin on both graphite (non-wetting) and copper (wetting) surfaces using in situ x-ray diffraction. The microstructure was further characterized by optical microscopy, scanning electron microscopy, and electron backscattering diffraction imaging microscopy. Undercoolings as high as 61 C were observed for Sn solidified on graphite, while lower undercoolings, up to 30 C, were observed for Sn solidified on copper. The microstructure of the high purity Sn sample solidified on graphite showed very few grains in the cross-section, while the commercially pure Sn sample solidified with only one grain and was twinned. Tin solidified on copper contained significant amounts of copper in the tin, intermetallic phase formation at the interface, and a eutectic microstructure.

36 MATERIALS SCIENCE↗